Ester flavorants detection in foods with a bienzymatic biosensor based on a stable Prussian blue-copper electrodeposited on carbon paper electrode

Acetylcholinesterase and butyrylcholinesterase co-immobilized on a copper containing Prussian blue modified electrode for the broad screening of insecticides

We have developed a bienzymatic biosensor that contains acetylcholinesterase together with butyrylcholinesterase co-immobilized on the same electrode modified with a stabilized copper containing Prussian blue electrodeposited on electrodes coated with 4-aminothiophenol monolayer using diazonium chemistry and copper nanoparticles for improved sensitivity. There are organophosphorus and carbamate neurotoxic insecticides that inhibit only one of the two enzymes, e.g., pirimicarb inhibits butyrylcholinesterase at much lower concentrations than acetylcholinesterase while methomyl inhibits only acetylcholinesterase. Our system is simple and in a single measurement provides a sensitive signal for insecticides' presence based on the inhibition of the enzyme with the highest affinity for each toxic compound. The limits of detection are 50 ng/mL pirimicarb for the bienzymatic biosensor in comparison with 400 ng/mL pirimicarb for the acetylcholinesterase biosensor and 6 ng/mL methomyl for the bienzymatic biosensor, while inhibition is obtained for the butyrylcholinesterase biosensor at 700 ng/mL.

Highly stable acetylcholinesterase electrochemical biosensor based on polymerized ionic liquids microgel for pesticides detection

A highly stable electrochemical biosensor for pesticide detection was developed. For the first time polymeric ionic liquids (PILs) were introduced to construct an acetylcholinesterase (AChE) biosensor . AChE was entrapped in PILs microspheres through an emulsion polymerization reaction, where negatively charged Au nanoparticles (Au NPs) can be immobilized by the positively charged PILs, leading to improved catalytic performance. The results suggest that the positively charged PILs not only provide a biocompatible microenvironment around the enzyme molecule, stabilizing its biological activity and preventing its leakage, but also act as a modifiable interface allowing other components with electron transport properties to be loaded onto the polymer substrate, thus providing an efficient electron transport channel for the entrapped enzyme. More notably, when AChE was immobilized in a positively charged environment, the active site is closer to the electrode, promoting faster electron transfer. The detection limits of the constructed electrochemical biosensor AChE@PILs@Au NPs/GCE toward carbaryl and dichlorvos (DDVP) were 5.0 × 10^-2 ng ml^-1 and 3.9 × 10^-2 ng ml^-1, in a wide linear range of 6.3 × 10^-2-8.8 × 10² ng ml^-1 and 1.3 × 10^-1-1.4 × 10³ ng ml^-1, respectively. More importantly, the biosensor has high thermal and storage stability, which facilitates rapid field analysis of fruits and vegetables in a variety of climates. In addition, the biosensor reported has good repeatability and selectivity and has high accuracy in the analysis of peaches, tap water, and other types of samples.

An amphiprotic paper-based electrode for glucose detection based on layered carbon nanotubes with silver and polystyrene particles

In this work, a flexible amphiprotic amino-bonded carbon nanotube-Ag nanoparticle/polystyrene (CNT-NH₂-Ag/PS) paper electrode was fabricated to measure glucose in human body fluids by a combination of vacuum filtration and high temperature baking. The front side of the fabricated paper electrode was hydrophobic and conductive, whereas its back side was hydrophilic and nonconductive. In the fabrication process, the coating sequence of CNT-NH₂, Ag and PS was critical to determine the performance of the resulting CNT-NH₂-Ag/PS electrode besides other parameters (e.g., amount of soluble starch, PS and Ag nanoparticles, type and amount of CNT-NH₂, and electrode sensing area). Based on a series of experimental observations, the possible mechanism of glucose detection on the paper electrode was proposed, in which glucose was more favorable to migrate to the hydrophilic back side of the paper and interact with the active species (e.g., O₂^-) on the electrode surface. The electrochemical results showed that the CNT-NH₂-Ag/PS paper electrode maintained stable electrochemical properties even after five cycles of use and 60 days of storage in air. The amphiprotic paper electrode demonstrated excellent sensing performance for glucose with a linear range of 1 μM to 1000 μM, a low detection limit of 0.2 μM, and a sensitivity of 31 333.0 μA mM^-1 cm^-2. The fabricated paper electrode was also successfully applied to detect different levels of glucose in complex human body fluids such as saliva, urine, and serum. These features make this type of paper electrode promising for glucose measurement.

A Novel Approach to the Facile Growth and Organization of Photothermal Prussian Blue Nanocrystals on Different Surfaces

We report here a novel "one-pot" approach for the controlled growth and organization of Prussian blue nanostructures on three different surfaces: pure Au0, cysteamine-functionalized Au0, and SiO2-supported lipid bilayers with different natures of lipids. We demonstrate that fine control over the size, morphology, and the degree and homogeneity of the surface coverage by Prussian Blue (PB) nanostructures may be achieved by manipulating different parameters, which are the precursor concentration, the nature of the functional groups or the nature of lipids on the surfaces. This allows the growth of isolated PB nanopyramids and nanocubes or the design of thin dense films over centimeter square surfaces. The formation of unusual Prussian blue nanopyramids is discussed. Finally, we demonstrate, by using experimental techniques and theoretical modeling, that PB nanoparticles deposited on the gold surface exhibit strong photothermal properties, permitting a rapid temperature increase up to 90 °C with a conversion of the laser power of almost 50% for power source heat.

Addressing the Selectivity of Enzyme Biosensors: Solutions and Perspectives

Enzymatic biosensors enjoy commercial success and are the subject of continued research efforts to widen their range of practical application. For these biosensors to reach their full potential, their selectivity challenges need to be addressed by comprehensive, solid approaches. This review discusses the status of enzymatic biosensors in achieving accurate and selective measurements via direct biocatalytic and inhibition-based detection, with a focus on electrochemical enzyme biosensors. Examples of practical solutions for tackling the activity and selectivity problems and preventing interferences from co-existing electroactive compounds in the samples are provided such as the use of permselective membranes, sentinel sensors and coupled multi-enzyme systems. The effect of activators, inhibitors or enzymatic substrates are also addressed by coupled enzymatic reactions and multi-sensor arrays combined with data interpretation via chemometrics. In addition to these more traditional approaches, the review discusses some ingenious recent approaches, detailing also on possible solutions involving the use of nanomaterials to ensuring the biosensors' selectivity. Overall, the examples presented illustrate the various tools available when developing enzyme biosensors for new applications and stress the necessity to more comprehensively investigate their selectivity and validate the biosensors versus standard analytical methods.

Paper and Other Fibrous Materials-A Complete Platform for Biosensing Applications

Paper-based analytical devices (PADs) and Electrospun Fiber-Based Biosensors (EFBs) have aroused the interest of the academy and industry due to their affordability, sensitivity, ease of use, robustness, being equipment-free, and deliverability to end-users. These features make them suitable to face the need for point-of-care (POC) diagnostics, monitoring, environmental, and quality food control applications. Our work introduces new and experienced researchers in the field to a practical guide for fibrous-based biosensors fabrication with insight into the chemical and physical interaction of fibrous materials with a wide variety of materials for functionalization and biofunctionalization purposes. This research also allows readers to compare classical and novel materials, fabrication techniques, immobilization methods, signal transduction, and readout. Moreover, the examined classical and alternative mathematical models provide a powerful tool for bioanalytical device designing for the multiple steps required in biosensing platforms. Finally, we aimed this research to comprise the current state of PADs and EFBs research and their future direction to offer the reader a full insight on this topic.

A non-enzymatic electrochemical biosensor based on Au@PBA(Ni-Fe):MoS2 nanocubes for stable and sensitive detection of hydrogen peroxide released from living cells

Hydrogen peroxide (H2O2) is the main product of enzymatic reactions and plays an important role in biological processes. The detection of H2O2 inside organisms or cells is critical. Here, we report a nickel-iron Prussian blue analogue nanocube doped with molybdenum disulfide and Au nanoparticles (Au@PBA(Ni-Fe):MoS2) as an electrochemical sensing material for the stable detection of H2O2 in neutral solutions for a long time. First, the Prussian blue analogue (PBA(Ni-Fe)) is synthesized by a simple charge-assembly technology, and then etched into PBA(Ni-Fe):MoS2 hollow nanocubes by a high-temperature hydrothermal reaction. Finally, Au nanoparticles are reduced inside the PBA(Ni-Fe):MoS2in situ to generate Au@PBA(Ni-Fe):MoS2 nanocubes. Ni-doping enhances the nanocube's stability in neutral solutions; as a result, the sensor can maintain a stable current response towards H2O2 reduction for more than 1 h. The sensing material can meet the needs of a long-time test. The introduction of Au enhances the electron transfer efficiency, which endows the sensor with good reduction ability for H2O2 at 0 V over a wide linear range (0.5-200 μM and 210-3000 μM) and with a low detection limit (0.23 μM (S/N = 3)), which fulfills the requirements for the detection of H2O2 in a biological system. The sensor can sense H2O2 released from cells stimulated by ascorbic acid. Au@PBA(Ni-Fe):MoS2 provides good guidance for the future development of efficient biosensors to be applied in cell biology.