Covalent immobilization of covalent organic framework on stainless steel wire for solid-phase microextraction GC-MS/MS determination of sixteen polycyclic aromatic hydrocarbons in grilled meat samples

Honeycomb-like triazine-based conjugated microporous polymers exhibiting simultaneous and ultrasensitive detection of fifteen polycyclic aromatic hydrocarbons using solid-phase microextraction technique

BACKGROUND

Since the severe hazard to the ecosystem and widespread distribution through biological and man-made ways of polycyclic aromatic hydrocarbons (PAHs), it is very urgent to establish the ultrasensitive analytical method to quantitatively and directly monitor PAHs in real samples. However, because of the complicated environmental matrix and their trace concentration, the pre-concentration process is a necessary step to analyze of these compounds. In this study, solid phase microextraction (SPME) technique was proposed to separate and enrich fifteen trace PAHs from environmental samples.

RESULTS

In this work, a honeycomb-like triazine-based conjugated microporous polymers (T-CMPs) were prepared by Yamamoto reaction and firstly used as SPME coating material for the ultrasensitive direct-immersion-SPME of PAHs prior to high performance liquid chromatography-fluorescence detector (HPLC-FLD). The synthesized T-CMPs was characterized using various spectroscopy and electron microscopy techniques. The unique porous network of T-CMPs might deliver abundant adsorption sites for PAHs. Orthogonal experimental design (OED) was used to investigate the influence of four experimental parameters on the enrichment ability. Under optimal situation, a wide linear range (which lasted from 0.003 to 1000 μg L-1) with the coefficients of determination (R2) varying 0.9981 to 0.9993 was obtained. The limits of detection (LODs) for the analytes varied from 0.001 to 1.650 μg L-1, and the limits of quantification (LOQs) were between 0.003 and 4.960 μg L-1. The proposed method was effectively employed to the simultaneous and ultrasensitive detection of fifteen PAHs in industrial wastewaters. The relative recoveries for PAHs analysis varied from 74.6 % to 105 % with the relative standard deviations (RSD) of 0.1 %-7.5 % in real water samples.

SIGNIFICANCE

The prepared SPME coating material exhibited a simultaneous, high extraction and adsorption capacity for fifteen PAHs due to its honeycomb-like porous structure, ultra-large specific surface area, strong π-π stacking, and hydrophobic interactions. The present research developed a novel strategy for the construction of SPME fiber coating composites and demonstrated great application potential in the field of sample pretreatment and environmental analytical chemistry.

Nitrogen-rich covalent organic framework as a practical coating for effective determinations of polycyclic aromatic hydrocarbons

Polycyclic aromatic hydrocarbons (PAHs) are high-profile organic pollutants to be poisonous, carcinogenic, and mutagenic, and widely distributed at trace levels in the environment. In order to effectively enrich PAHs, two stable covalent organic frameworks (COFs, TAPT-OMe-PDA and TPB-DMTP) were prepared by combining 2,4,6-tri(4-aminophenyl)-1,3,5-triazine (TAPT) and 1,3,5-tri(4-aminophenyl) benzene (TAPB) with 2,5-dimethoxy-phenyl-1,4-diformaldehyde (OMe-PDA), respectively. Even though the surface area of TAPT-OMe-PDA was much lower than that of TPB-DMTP, it still demonstrated much better extraction efficiencies towards PAHs as the solid phase microextraction (SPME) coating. Therefore, the TAPT-OMe-PDA coated fiber was coupled with gas chromatography-mass spectrometry (GC-MS) to establish a practical and sensitive method, after the extraction parameters (extraction time, extraction temperature, desorption temperature, desorption time, salt concentration and pH) were optimized. This developed analytical method showed wide linear ranges, low limits of detection, good repeatability and reproducibility. Finally, five PAHs in three water samples were detected and quantified precisely (2.72-38.7 ng·L-1) with satisfactory recoveries (88.3%-118%).

In situ fabrication of covalent organic frameworks on solid-phase microextraction probes coupled with electrospray ionization mass spectrometry for enrichment and determination of androgens in biosamples

Solid-phase microextraction (SPME) coupled with electrospray ionization mass spectrometry (ESI-MS) was developed for rapid and sensitive determination of endogenous androgens. The SPME probe is coated with covalent organic frameworks (COFs) synthesized by reacting 1,3,5-tri(4-aminophenyl)benzene (TPB) with 2,5-dioctyloxybenzaldehyde (C8PDA). This COFs-SPME probe offers several advantages, including enhanced extraction efficiency and stability. The analytical method exhibited wide linearity (0.1-100.0 µg L-1), low limits of detection (0.03-0.07 µg L-1), high enrichment factors (37-154), and satisfactory relative standard deviations (RSDs) for both within one probe (4.0-14.8%) and between different probes (3.4-12.7%). These remarkable performance characteristics highlight the reliability and precision of the COFs-SPME-ESI-MS method. The developed method was successfully applied to detect five kinds of endogenous androgens in female serum samples, indicating that the developed analytical method has great potential for application in preliminary clinical diagnosis.

Recent progress of covalent organic frameworks as attractive materials for solid-phase microextraction: A review

Solid-phase microextraction (SPME) is a green, environmentally friendly, and efficient technique for sample pre-treatment. Covalent organic frameworks (COFs), a class of porous materials formed by covalent bonds, have gained prominence owing to their remarkable attributes, including large specific surface area, tunable pore size, and robust thermal/chemical stability. These characteristics have made COFs highly appealing as potential coatings for SPME fiber over the past decades. In this review, various methods used to prepare SPME coatings based on COFs are presented. These methods encompass physical adhesion, sol-gel processes, in situ growth, and chemical cross-linking strategies. In addition, the applications of COF-based SPME coating fibers for the preconcentration of various targets in environmental, food, and biological samples are summarized. Moreover, not only their advantages but also the challenges they pose in practical applications are highlighted. By shedding light on these aspects, this review aims to contribute to the continued development and utilization of COF materials in the field of sample pretreatment.

Covalent organic framework in situ grown on the metal-organic framework as fiber coating for solid-phase microextraction of polycyclic aromatic hydrocarbons in tea

A novel MIL-88-NH2@COF composite was produced by in situ growth of covalent organic framework (COF) on the metal-organic framework (MOF) surface. To obtain a coating fiber for solid-phase microextraction (SPME), the MIL-88-NH2@COF composite physically adhered to the stainless steel wire. Combined with gas chromatography-flame ionization detection (GC-FID), various analytes such as chlorophenols (CPs), phthalates (PAEs), and polycyclic aromatic hydrocarbons (PAHs) were extracted and determined to evaluate the extraction performance of MIL-88-NH2@COF coated fibers and explore their extraction mechanism. This composite exhibit excellent extraction performance and adsorption capacity for various analytes, especially for PAHs with enrichment factor up to 9858. The SPME-GC-FID method based on MIL-88-NH2@COF fiber was established for the determination of five PAHs after the main extraction conditions were optimized. Under optimal conditions, the proposed technique showed a wide linear range (1-150 ng mL-1) with a low limit of detection (0.019 ng mL-1) and a high coefficient of determination (R2 > 0.99). The developed SPME-GC-FID method was used to determine PAHs in green tea and black tea samples, with good recoveries of 51.70-103.64% and 68.56-103.64%, respectively. It is worth mentioning that this is the first time MIL-88-NH2@COF composites have been prepared and applied to SPME. The preparation method of the composite provides a new idea in adsorbent preparation, which will contribute to the field of SPME.

The covalent organic framework based nylon membrane extraction coupled with UHPLC-MS/MS for highly efficiency determination of hexabromocyclododecanes in environmental water

Hexabromocyclododecanes (HBCDs) have given their adverse effects on environment and human health, and highly sensitive analysis of HBCDs in water is urgent. In this study, a new method for the determination of trace HBCDs in water was established by covalent organic framework (COF) based nylon membrane extraction (ME) coupled with ultrahigh-performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS). The COF had been self-assembled onto the nylon membrane in a gentle strategy to fabricate COF nylon membrane. Several important ME parameters including the dosage of COF, pH, eluent condition and salinity were systematically investigated. The limits of detection and quantification were 0.011-0.014 and 0.038-0.047 ng/L for three HBCDs, respectively. The linear ranges were from 0.04 to 20 ng/L, and the relative standard deviations were 5.7-17.8 % (intra-day) and 5.2-14.1 % (inter-day). In addition, density functional theory (DFT) calculations on adsorption energy proved that the introduction of halogen bond (XB) made a key contribution to high extraction efficiency and excellent selectivity of COF nylon membrane for HBCDs. The 500 mL of samples, including tap water and reservoir water, could be extracted only in 23 min. The established method presented highly sensitive for ultra-trace analysis of HBCDs in environmental water.

In situ growth of porous organic framework on iron wire for microextraction of polycyclic aromatic hydrocarbons

In this work, a novel spherical metal organic framework (MOF) was first in situ grown on the surface of iron wire (IW), in which IW served as the substrate and metal source for MOF (type NH₂-MIL88) growth without adding additional metal salts in the process, while spherical NH₂-MIL88 provided more active sites for further construction of multifunctional composites. Subsequently, a covalent organic framework (COF) was covalently bonded to the surface of the NH₂-MIL88 to obtain the IW@NH₂-MIL88@COF fibers, which were used for headspace solid-phase microextraction (HS-SPME) of polycyclic aromatic hydrocarbons (PAHs) in milk samples prior to determination by gas chromatography-flame ionization detection (GC-FID). Compared with the fiber prepared by physical coating, the IW@NH₂-MIL88@COF fiber prepared by in situ growth and covalent bonding exhibits better stability and possesses more uniform layer. The extraction mechanism of the IW@NH₂-MIL88@COF fiber for PAHs was discussed, which mainly owed to π-π interactions and hydrophobic interactions. After optimization of the primary extraction conditions, the SPME-GC-FID method was established for five PAHs with a wide linear range (1-200 ng mL^-1), good linearity coefficient (0.9935-0.9987) and low detection limits (0.017-0.028 ng mL^-1). The relative recoveries for PAHs detection in milk samples ranged from 64.69 to 113.97%. This work not only provides new ideas for the in situ growth of other types of MOF, but also provides new methods for the construction of multifunctional composites.

In-situ growth of covalent organic framework on stainless steel needles as solid-phase microextraction probe coupled with electrospray ionization mass spectrometry for rapid and sensitive determination of tricyclic antidepressants in biosamples

Tricyclic antidepressants (TCAs) including amitriptyline (AT), doxepin (DOX) and nortriptyline (NT) are the first-line drugs for the clinical treatment of depression; however, monitoring TCA concentrations in biological fluids and tissues is necessary to improve therapeutic effect and determine the cause of death in patients. It is of great significance to develop a rapid and sensitive method for real-time monitoring of TCAs in various biosamples. In this work, we fabricated a novel covalent organic framework (COF) based solid-phase microextraction (SPME) probe by an in-situ step-by-step strategy, which was obtained by sequentially modifying 1,3,5-tri (4-aminophenyl) benzene (TPB) and 2, 5-divinylbenzaldehyde (DVA) on the surface of polydopamine layer. The TPB-DVA-COF-SPME probe possessed high specific surface area (1244 m²·g ^- 1), regular pores (3.23 nm), good hydrophobicity and stability, resulting in efficient enrichment for TCAs. Furthermore, the combination of TPB-DVA-COF-SPME probe and ambient electrospray ionization mass spectrometry system (ESI/MS) was firstly proposed for rapid and sensitive determination of TCAs in biosamples. As a result, the developed method exhibited low limits of detection (LODs) (0.1-0.5 μg∙L ^- 1), high enrichment factors (39-218), and low relative standard deviations (RSDs) for one probe (1.2-3.8%) and probe-to-probe (2.0-3.7%). Benefiting from these outstanding performance, TPB-DVA-COF-SPME probe was further successfully applied to biosamples (i.e., serum, liver, kidney, and brain) with excellent reusability, indicating the promising applicability of the TPB-DVA-COF-SPME-ESI/MS as a powerful tool for drug monitoring.

Preparation of a New Solid-Phase Microextraction Fiber Based on Molecularly Imprinted Polymers for Monitoring of Phenobarbital in Urine Samples

A simple solid-phase microextraction technique using molecularly imprinted polymers (MIP-SPME) was prepared to monitor phenobarbital in urine samples. In this technique, the fiber was prepared via insertion of the modified stainless-steel wire in the reaction solution including 3-aminopropyltriethoxysilane and tetraethyl orthosilicate in the presence of an acidic catalyst (acetic acid). The fabricated MIP-SPME fiber was utilized to selectively extract phenobarbital from urine samples and prepare it for detection through high-performance liquid chromatography with ultraviolet detection. The synthesized MIPs were characterized by several techniques such as Fourier-transform infrared spectroscopy, field emission scanning electron microscopy, and thermal gravimetric analysis. The effects of various influencing factors on the extraction yield of phenobarbital were considered and optimized. The conditions that yielded the maximum extraction efficiency were as follows: pH of 5, 25 min extraction time, 500 rpm stirring rate, 15 min desorption time and using methanol as elution solvent. Within the range of concentrations of 0.02 to 100 μg mL-1, the method had linear characteristics, with a suitable coefficient of determination (0.9983). We determined limits of detection and limits of quantification to be 9.88 and 32.9 ng mL-1, respectively. The repeatability and reproducibility of the prepared fibers were 4.6 and 6.5%, respectively.

Flavor formation based on lipid in meat and meat products: A review

Meat product is popular throughout the world due to its unique taste. Flavor is one of the most important quality characteristics of meat products and also is a key influencing factor in the overall acceptability of meat products. The flavor of meat products is formed by precursors undergoing a series of complex reactions. During meat product processing, lipids are hydrolyzed by lipase to produce flavor precursors such as free fatty acid, then further oxidized to form volatile flavor compounds. This review summarizes lipolysis, lipid oxidation, and interaction of lipid with Maillard reaction and amino acid during meat products processing and storage as well as influencing factors on lipid degradation including raw meat (source of meat, feeding pattern, and castration), processing methods (thermal processing, nonthermal processing, salting, and fermentation) and additives. Meanwhile, the volatile compounds produced by lipids in meat products including aldehydes, alcohols, ketones, and hydrocarbons are summed up. Analytical methods of volatile compounds and the application of lipidomics analysis in mechanisms of flavor formation of meat products are also reviewed. PRACTICAL APPLICATIONS: Flavor is one of the most important quality characteristics of meat products, which influences the acceptability of meat products for consumption. Lipids play an important role in the flavor formation of meat products. Understanding the relationship between flavor compounds and changes in lipid compositions during the processing and storage of meat products will be helpful to control the quality of meat products.

[Application progress of covalent organic framework materials in extraction of toxic and harmful substances]

Toxic and hazardous substances constitute a category of compounds that are potentially hazardous to humans, other organisms, and the environment. These substances include pesticides (benzoylureas, pyrethroids, neonicotinoids), persistent organic pollutants (polycyclic aromatic hydrocarbons, polychlorinated biphenyls, perfluorinated compounds), plasticizers (phthalate esters, phenolic endocrine disruptors), medicines (sulfonamides, non-steroid anti-inflammatory drugs, tetracyclines, fluoroquinone antibiotics), heterocyclic aromatic amines, algal toxins, and radioactive substances. Discharge of these toxic and harmful substances, as well as their possible persistence and bioaccumulation, pose a major risk to human health, often to the extent of being life-threatening. Therefore, it is important to analyze and detect toxic and hazardous substances in the environment, drinking water, food, and daily commodities. Sample pretreatment is an imperative step in most of the currently used analytical methods, especially in the analysis of trace toxic and harmful substances in complex samples. An efficient and fast sample pretreatment technology not only helps improve the sensitivity, selectivity, reproducibility, and accuracy of analytical methods, but also avoids contamination of the analytical instruments and even damages the performance and working life of instruments. Sample pretreatment techniques widely used in the extraction of toxic and hazardous substances include solid-phase extraction (SPE), solid-phase microextraction (SPME), and dispersed solid-phase extraction (DSPE). The adsorbent material plays a key role in these pretreatment techniques, thereby determining their selectivity and efficiency. In recent years, covalent organic frameworks (COFs) have attracted increasing attention in sample pretreatment. COFs represent an exciting new class of porous crystalline materials constructed via the strong covalent bonding of organic building units through a reversible condensation reaction. COFs present four advantages: (1) precise control over structure type and pore size by consideration of the target molecular structure based on the connectivity and shape of the building units; (2) post-synthetic modification for chemical optimization of the pore interior toward optimized interaction with the target; (3) straightforward scalable synthesis; (4) feasible formation of composites with magnetic nanoparticles, carbon nanotubes, graphene, silica, etc., which is beneficial to enhance the performance of COFs and meet the requirement of diverse pretreatment technologies. Because of the well-defined crystalline porous structures and tailored functionalities, COFs have excellent potential for use in target extraction. However, some issues need to be addressed for the application of COFs in the extraction of toxic and hazardous substances. (1) For the sample matrix, most of the reported COFs are highly hydrophobic, which limits their dispersibility in water-based samples, leading to poor extraction performance. COFs with good dispersibility in water-based samples are urgently required. (2) Besides, COFs rely on hydrophobic interaction, size repulsion, π-π stacking, and Van der Waals forces to extract target substances, but they are not effective for some polar targets. Thus, it is necessary to develop COFs with high affinity for polar toxic and hazardous substances. (3) Methods for the synthesis of COFs have evolved from solvothermal methods to room-temperature methods, mechanical grinding, microwave-assisted synthesis, ion thermal methods, etc. Most of the existing methods are time-consuming, laborious, and environmentally unfriendly. The starting materials are too expensive to prepare COFs in large quantities. More effort is required to improve the synthesis efficiency and overcome the obstacles in the application of COFs for extraction. This article summarizes and reviews the research progress in COFs toward the extraction of toxic and hazardous substances in recent years. Finally, the application prospects of COFs in this field are summarized, which serves as a reference for further research into pretreatment technologies based on COFs.

Poly(divinylbenzene) as a fiber coating for headspace solid-phase microextraction of polycyclic aromatic hydrocarbons from river water

Porous polydivinylbenzene microspheres with high specific surface area were prepared by distillation-precipitation polymerization, and were used as the coating material in headspace solid phase microextraction for extracting polycyclic aromatic hydrocarbons. Compared with the other reported sorbents, PDVB exhibits lower cost and higher extraction efficiency, and the enrichment factors can reach 5963-16 720.

The analysis and probabilistic health risk assessment of polycyclic aromatic hydrocarbons in cereal products

The analysis and probabilistic health risk assessment of polycyclic aromatic hydrocarbons (PAHs) in cereal products were done by using magnetic solid-phase extraction (MSPE) method and gas chromatography/mass spectrometric (GC/MS). The results of method showed LOQ and LOD of PAHs compounds were 0.105-0.180 and 0.035-0.060 µg/kg, and the recorded values were 4.3-12.1 and 6.1-20.3% for repeatability and reproducibility with an estimated recovery of 94.4-103.4%. In this study, we analyzed kind of bread (Barbari, Sangak, Baguette, Taftoon, Lavash), macaroni, lasagna, and cooked rice that mean of total PAHs were 98.2, 121.7, 134.9, 166.3, 176.3, 176.2, 130.1, and 248.3 μg/kg, respectively. Further, the correlation between the type and amount of 16 PAHs with cereal products samples evaluated with multivariate principal component analysis and heat map visualization. The highest incremental lifetime cancer risk (ILCR) was found in cooked rice (7.80E-6), while the lowest ILCR was found in Lasagna (2.35E-07). In conclusion, the PAHs content in the tested products were in low health risk ranges (1 × 10^-6 < ILCR < 1 × 10^-4), and all of the cereal products sold in Tehran are considered safe for consumers. Therefore, cereal products should be regularly evaluated and monitored by regulatory agencies to reduce contaminants in these high-consumption products.

High efficient solid-phase microextraction based on a covalent organic framework for determination of trifluralin and chlorpyrifos in water and food samples by GC-CD-IMS

Novel porous covalent organic framework (COF) based on condensation reaction between cyanuric chloride, 4,4'-ethylendianiline, and 3,4,9,10-perylenetetracarboxylic dianhydride was synthesized via sealed tube condition. The results COF was used as a new adsorbent for solid-phase microextraction (SPME) for extracting trifluralin and chlorpyrifos from vegetables, fruit samples, and wastewater. Gas chromatograph with a corona discharge-ion mobility spectrometer as the detector was also used for analyzing the target analytes. Some parameters that affected the extraction, such as stirring rate, time and temperature of extraction and pH were investigated, exhaustively. The detection limits were 0.13, and 0.15 µg/L and the linear ranges of 0.45-20 and 0.50-25 µg/L with a linearity coefficient of 0.9965 and 0.9987 were also obtained for trifluralin and chlorpyrifos, respectively. The method was applied successfully to analyze some real samples of cucumber, carrot, grape, and agriculture wastewater, and the results showed a relative recovery in the range of 87% to 110%.

Application of imine covalent organic frameworks in sample pretreatment

亚胺类共价有机骨架(I-COFs)是有机单体根据席夫碱(Schiff-base)反应原理缩合形成的一类新型多孔晶体有机材料。I-COFs具有骨架密度低、比表面积大、孔隙率高、单体种类丰富、孔径尺寸可控、结构可功能化、合成方法多样和物化稳定性好等优点。近年来,I-COFs已成为材料科学领域的研究前沿,并广泛用于气体吸附、存储、催化、传感、光电材料等方面。I-COFs材料优异的物理化学性能使其非常适于用作复杂样品中痕量目标物的分离富集介质,其高比表面积、高孔隙率性能赋予了它极高的吸附负载量,这些性能使得目标分析物可被高效富集;通过控制有机单体的链段长度、几何结构、掺杂元素、取代基团等方面精确调控I-COFs的孔洞结构和功能化基团,从而实现目标痕量物质的选择性富集。目前,I-COFs材料在样品前处理领域作为新型萃取介质已引起了极大关注。该文综述了近年来I-COFs材料的主要类型、合成方法及其在固相萃取、磁性固相萃取、分散固相萃取和固相微萃取方面的研究进展,同时展望了I-COFs在样品前处理领域的发展前景。

GNP/Al-MOF nanocomposite as an efficient fiber coating of headspace solid-phase micro-extraction for the determination of organophosphorus pesticides in food samples

The synthesis and utilization of a high porous nanocomposite comprising MIL-53(Al) metal-organic framework (Al-MOF) and graphene nanopowder (GNP) is reported as a fiber coating for headspace solid-phase micro-extraction (HS-SPME) of selected organophosphorus pesticides (OPPs) from apple, potato, grape juice, tomato, and river water. The adsorbed OPPs on the coated fiber were subsequently determined using GC-MS. Several parameters affecting the efficiency of extraction including time and temperature of extraction, desorption condition of extracted analytes, pH and agitation of sample solution, and salt concentration were investigated. The optimum extraction condition was achieved at 70 °C with an extraction time of 40 min, pH = 4-8, and NaCl concentration of 6.0% (w/v). The best condition of desorption were observed at 280 °C for 2.0 min under a flow of helium gas in the GC inlet. Under optimal conditions, the detection limits ranged from 0.2 to 1.5 ng g^-1 and the linear ranges between 0.8 and 600 ng g^-1. The proposed method showed very good repeatability with RSD values ranging from 4.5 to 7.3% (n = 5). The relative recoveries were between 88% and 109% at the spiked level of 25.0 ng g^-1 for the tomato sample. The fabricated fiber exhibited good enrichment factor (62-195) at optimum condition of HS-SPME. The applied HS-SPME technique is facile, fast, and inexpensive. The thermally stable GNP/Al-MOF exhibited a high sensitivity toward OPPs. So, this nanocomposite can be considered as a sorbent for the micro-extraction of other pesticides in food.

Covalent organic frameworks as multifunctional materials for chemical detection

Sensitive and selective detection of chemical and biological analytes is critical in various scientific and technological fields. As an emerging class of multifunctional materials, covalent organic frameworks (COFs) with their unique properties of chemical modularity, large surface area, high stability, low density, and tunable pore sizes and functionalities, which together define their programmable properties, show promise in advancing chemical detection. This review demonstrates the recent progress in chemical detection where COFs constitute an integral component of the achieved function. This review highlights how the unique properties of COFs can be harnessed to develop different types of chemical detection systems based on the principles of chromism, luminescence, electrical transduction, chromatography, spectrometry, and others to achieve highly sensitive and selective detection of various analytes, ranging from gases, volatiles, ions, to biomolecules. The key parameters of detection performance for target analytes are summarized, compared, and analyzed from the perspective of the detection mechanism and structure-property-performance correlations of COFs. Conclusions summarize the current accomplishments and analyze the challenges and limitations that exist for chemical detection under different mechanisms. Perspectives on how future directions of research can advance the COF-based chemical detection through innovation in novel COF design and synthesis, progress in device fabrication, and exploration of novel modes of detection are also discussed.

Plugged bifunctional periodic mesoporous organosilica as a high-performance solid phase microextraction coating for improving extraction efficiency of chlorophenols in different matrices

In this study, a sensitive solid phase microextraction (SPME) coating was developed based on two kinds of plugged and non-plugged bifunctional periodic mesoporous organosilicas (BFPMO) with ionic liquid and ethyl units. The extraction efficiency of all plugged and unplugged sorbents was investigated for the extraction of chlorophenols (CPs) in water and honey samples by emphasizing the effect of different physicochemical properties. The separation and determination of the CPs was performed by gas chromatography-mass spectrometry (GC-MS). The extraction results showed that plugged BFPMO coating exhibited outstanding enrichment ability for the extraction of CPs as model analytes with different polarities. This can be attributed to a valuable hydrophobic-hydrophilic balance in the mesochanels of the plugged BFPMO, which is the result of the combination of plug technology and bridged organic groups. Low limits of detection in the range of 5-70 ng L^-1, wide linearity, and good reproducibility (RSD = 8.1-10.1 % for n = 6) under the optimized extraction conditions were achieved. Finally, the BFPMOs coated fiber was successfully used for determination of CPs in real water samples. The relative recoveries for the five CPs were in the range of 92.3-104.0 %, which proved the applicability of the method.

In-situ fabrication of a chlorine-functionalized covalent organic framework coating for solid-phase microextraction of polychlorinated biphenyls in surface water

The functionalization of covalent organic frameworks (COFs) identifies significant potential for developing selective coating materials for solid-phase microextraction (SPME). Herein, a chlorine-functionalized covalent organic framework (CF-COF) was in-situ synthesized by employing triformylphloroglucinol (Tp) and 2,5-dichloro-1,4-phenylenediamine (2,5-DCA) as monomers on an amino-functionalized stainless steel wire. The obtained CF-COF coated fiber exhibited a higher enrichment capacity for polychlorinated biphenyls (PCBs) than commercial fibers and non-chlorinated COF fiber, owing to a more hydrophobic surface, size-matching effect, a large number of micropores and the π-π stacking interactions between COF coating and analytes. As a practical application, the CF-COF coated fiber was applied to the headspace extraction of 17 PCBs prior to their quantification by GC/MS. The established analytical method offered a good linearity in the range of 0.1-1000 ng L^-1, low detection limits of 0.0015-0.0088 ng L^-1, and satisfactory enhancement factors (EFs) of 699-4281. The repeatability for single fiber and the fiber-to-fiber reproducibility was lower than 9.26% and 9.33%, respectively. The proposed method was verified to be sensitive, selective, and applicable for the analysis of ultra-trace PCBs in environmental surface water samples with the recoveries ranged from 78.7% to 124.0%.

Novel nanohybrids for effervescence enhanced magnetic solid-phase microextraction of wide-polarity organic pollutants in roasted meat samples

To simultaneously and efficiently extract pollutants with differential polarities, we herein fabricated and characterized a multifunctional nanocomposite. The novel nanohybrids used NiFe₂ O₄ as magnetic cores, and NH₂ -MIL-101(Al), β-cyclodextrin and graphene oxide as functional components combined with magnetic cores. With the aid of graphene oxide's large π-conjugated system, NH₂ -MIL-101(Al)'s strong adsorption to moderately/strongly polar chemicals, and β-cyclodextrin's specific recognition effect, the nanohybrids realized synergistically efficient extraction of polyaromatic hydrocarbons and bisphenols with a log^Kow range of 3-6. Combined with acidic and alkaline sources, the nanohybrids-based effervescent tablets were prepared. Based on effervescent reaction-enhanced nanohybrids-based efficient adsorption/extraction and high performance liquid chromatography and fluorescence detection, we successfully developed an excellent microextraction method for the simultaneous determination of both polyaromatic hydrocarbons and bisphenols in roasted meat samples. Several important variables were optimized as follows: Na₂ CO₃ and tartaric acid as acidic and alkaline sources, 900 μLof the mixed solvent (acetone and hexane at 2:1 by v/v) as the eluent, 5 min of elution time. Under optimized conditions, the novel method gave low limits of detection (0.07-0.30 μg kg^-1 ), satisfactory recoveries (86.9-103.9%), and high precision (relative standard deviations of 1.9-6.7%) in roasted lamb, beef, pork, chicken, and sausage samples.

Comprehensive Strategy for Sample Preparation for the Analysis of Food Contaminants and Residues by GC-MS/MS: A Review of Recent Research Trends

Food safety and quality have been gaining increasing attention in recent years. Gas chromatography coupled to tandem mass spectrometry (GC-MS/MS), a highly sensitive technique, is gradually being preferred to GC-MS in food safety laboratories since it provides a greater degree of separation on contaminants. In the analysis of food contaminants, sample preparation steps are crucial. The extraction of multiple target analytes simultaneously has become a new trend. Thus, multi-residue analytical methods, such as QuEChERs and adsorption extraction, are fast, simple, cheap, effective, robust, and safe. The number of microorganic contaminants has been increasing worldwide in recent years and are considered contaminants of emerging concern. High separation in MS/MS might be, in certain cases, favored to sample preparation selectivity. The ideal sample extraction procedure and purification method should take into account the contaminants of interest. Moreover, these methods should cooperate with high-resolution MS, and other sensitive full scan MSs that can produce a more comprehensive detection of contaminants in foods. In this review, we discuss the most recent trends in preparation methods for highly effective detection and analysis of food contaminants, which can be considered tools in the control of food quality and safety.

In situ room-temperature rapidly fabricated imine-linked covalent organic framework coated fibers for efficient solid-phase microextraction of pyrethroids

A facile and rapid strategy for preparation of covalent organic framework (COF) coated fibers at ambient temperature is urgently needed for solid-phase microextraction (SPME) technology. In this work, an in situ room-temperature rapid growth strategy was developed to high-efficiently fabricate imine-linked COF (TPB-DVA) coated fibers in as little as 30 min at room temperature, and the thickness of the coating reached 9 μm. The prepared TPB-DVA coated fiber offer high thermal and chemical stability, and outstanding service lifetime. Moreover, we generalize this strategy to other two imine-linked COF (TPB-DMTP and TFPB-TAPB) coated fibers and the fibers were fabricated at room temperature for 3 h and 12 h, respectively, which demonstrate the applicability of this strategy. Subsequently, a SPME-GC-MS/MS analytical method was developed for trace pyrethroids (PYs) detection, which exhibited high enhancement factors (EFs, 2700-13195), wide linear range (0.08-800 ng L^-1), low limits of detection (LODs, 0.02-0.20 ng L^-1), and good repeatability (RSD ≤ 8.5%, n = 6). Furthermore, the developed analytical method was applied to tea samples and trace PYs (1.31-4.32 ng L^-1) were found with satisfactory recovery (80.2-119.8%). The above results demonstrated that the feasibility of the developed strategy for the facile and rapid fabrication of imine-linked COF coated fibers.

Hollow zeolitic imidazolate framework-7 coated stainless steel fiber for solid phase microextraction of volatile biomarkers in headspace gas of breast cancer cell lines

In this work, we reported the preparation of the hollow zeolitic imidazolate framework-7 (ZIF-7) via etching ZIF-7 with tannic acid, and further fabricated the hollow ZIF-7 coated fiber for the solid phase microextraction (SPME) of the five volatile biomarkers (acetone, isopropanol, hexanal, hexanol and decanal) generated from breast cancer cell lines. The hollow structure not only endowed higher extraction performance for the SPME of analytes, but also improved the diffusion rate of the analytes inside the hollow ZIF-7. Under the optimal conditions, the hollow ZIF-7 coated fiber offered high extraction capacity (25-153 mg g^-1) and enhancement factors (EFs, 2023-11250) for the five biomarkers, good linearity (R² > 0.9918) of acetone and isopropanol (2.5-500 μg L^-1) and hexanol, hexanal, and decanal (1.0-100 μg L^-1), low limits of detection (S/N = 3) of 0.07-0.53 μg L^-1 and the limit of quantifications (LOQs, S/N = 10) of 0.23-1.76 μg L^-1. The precisions (RSDs, %) for intra-day (n = 6), inter-day (n = 5) and fiber-to-fiber (n = 6) were 2.8-7.5%, 4.3-8.5%, and 4.2-14.6%, respectively. The high EFs of the hollow ZIF-7 coated fiber for the five biomarkers resulted from the integrated effects of the large surface area, the unique porous structure, hydrophobic interaction, gate-opening effect, and enhanced properties after etching including faster mass transport, multiple active components, and more exposed active sites. The fabricated hollow ZIF-7 coated fiber lasted at least 140 cycles of extraction/desorption/aging without obvious decrease of extraction ability and no change of crystal structure. Finally, the hollow ZIF-7 coated fiber combined with GC-FID had been successfully used to detect the five biomarkers in the headspace gas of human breast cancer cell lines (MDA-MB-231) and normal mammary cell lines (CCD-1095Sk) with the recoveries of 84-105%. These results revealed the prospect of hollow MOFs as efficient adsorbents for sample pretreatment.

In situ fabrication of nitrogen doped graphitic carbon networks coating for high-performance extraction of pyrethroid pesticides

The tailor-prepare solid phase microextraction (SPME) coatings with stable and excellent properties to effectively extract analytes from sample matrix still remains a challenge. Herein, a nitrogen doped graphitic carbon networks (NG-CNTW) coated fiber was fabricated by direct carbonization of nanosized ZIF-67 crystals (nano-ZIF-67) that grown on stainless steel wire. The NG-CNTW coated fiber coupled with gas chromatography-tandem mass spectrometry (GC-MS/MS) was applied for enrichment and determination of pyrethroids. The NG-CNTW coating exhibited high surface area and hierarchical porous structures that facilitate diffusion and accessibility of target molecules. Simultaneously, the nitrogen doped and highly graphitic structures endow the coating with high adsorption affinity for aromatic compounds. Under optimum conditions, the SPME-GC-MS/MS method presented wide range of linearity performance (0.08-200.0 ng g^-1), low limits of detection (0.02-0.5 ng g^-1) and good repeatability (RSD < 9.6%) for 8 kinds of pyrethroids. Furthermore, the proposed method was successfully applied in the determination of pyrethroids in grape and cauliflower samples, as the results were in the range of 3.16-15.06 ng g^-1and 2.08-9.29 ng g^-1, respectively. This work not only provides a new method by fabricating carbon nanomaterial coatings in situ derived from MOFs, but also shows great potential of MOFs derivative materials in environmental analysis field.

Development of a SPE/GC-MS method for the determination of organophosphorus pesticides in food samples using syringe filters packed by GNP/MIL-101(Cr) nanocomposite

In this study, we report the synthesis and application of a nanocomposite comprising metal-organic framework MIL-101(Cr) and graphene nanopowder (GNP) as a promising sorbent for the extraction of organophosphorus pesticides (OPPs) in juices, water, vegetables and honey samples. A syringe filter, for the first time, was used to host the synthesized nanocomposite and extract the OPPs followed by GC-MS analysis. Different characterization methods including XRD, FTIR, TGA, BET and SEM were employed to confirm the formation of studied nanocomposite. The results indicated that the GNP/MIL-101(Cr) could provide higher capacity for adsorption of OPPs and lower detection limit compared to pristine MIL-101(Cr). The detection limits were 0.005 to 15.0 µg/Kg and the linear range found between 0.05 and 400 µg/Kg. The proposed method showed very good repeatability with the RSD values ranging from 2.9% to 7.1%. The recoveries were between 84% -110% with the spiked levels of 2.0-100.0 µg/Kg.

A solid-phase microextraction fiber coating based on magnetic covalent organic framework for highly efficient extraction of triclosan and methyltriclosan in environmental water and human urine samples

Herein, we synthesized a kind of magnetic covalent organic framework nanohybrids (NiFe₂O₄@COF), and integrated it with polydimethyl siloxane and silicone rubber curing agent for solid phase microextraction (SPME) fiber coating. The fiber coating demonstrated a porous and uniform surface with the BET specific surface of 169.7 m² g^-1. As for seven environmental analytes, the NiFe₂O₄@COF-based SPME fiber coating gave the higher extraction recoveries for triclosan (TCS) and methyltriclosn (MTCS) than those of fenpropathrin, bifenthrin, permethrin, fenvalerate and deltamethrin. Several operational parameters were rigorously optimized, such as extraction temperature, extraction time, thermal desorption time, solution pH and salt effect. Combined with the GC-ECD detection, the newly developed microextraction method supplied the wide linear range of 0.1-1000 µg L^-1 with the correlation coefficients of > 0.9995. The limits of detection (LODs) and limits of quantitation (LOQs) reached as low as 1-7 ng L^-1 and 3.3-23 ng L^-1, respectively. The intra-day and inter-day precisions in six replicates (n = 6 ) were < 3.55% and < 5.06%, respectively, and the fiber-to-fiber reproducibility (n = 3) was < 7.64%. To evaluate its feasibility in real samples, the fortified recoveries for TCS and MTCS, at low (0.2 µg L^-1), middle (2.0 µg L^-1) and high (20.0 µg L^-1) levels, varied between 81.9% and 119.1% in tap, river and barreled waters as well as male, female and children urine samples. Especially, it is worth mentioning that the NiFe₂O₄@COF-based SPME coating fiber can be recycled for at least 150 times with nearly unchanged extraction efficiency. Moreover, the extraction recoveries by the as-fabricated fiber coating were much higher than those by three commercial fibers (PDMS, PDMS/DVB and PDMS/DVB/CAR). Overall, the NiFe₂O₄@COF-based SPME is a convenient, sensitive, efficient and "green" pretreatment method, thereby possessing important application prospects in trace monitoring of TCS-like pollutants in complex liquid matrices.

Ketoenamine Covalent Organic Framework Coating for Efficient Solid-Phase Microextraction of Trace Organochlorine Pesticides

Fiber coating is a key part of solid-phase microextraction (SPME) technology, and it determines the selectivity, sensitivity, and reproducibility of the analytical method. A ketoenamine covalent organic framework called Tp-Azo-COF with rich electronegative N atoms was prepared as an SPME coating in this work. The Tp-Azo-COF coating had a large surface area of 1218 m² g^-1 and good thermal and chemical stability, and it was applied for the extraction of organochlorine pesticides (OCPs). According to quantum chemistry calculations, the adsorption affinity of the Tp-Azo-COF coating for five OCPs was primarily affected by the halogen bond and hydrophobicity interaction. The extraction efficiencies of the Tp-Azo-COF coating for five OCPs were higher than those of three commercial SPME fiber coatings, and the enrichment factors ranged from 1061 to 3693. When combined with gas chromatography-tandem mass spectrometry, a wide linear range (0.1-1000 ng L^-1), low limits of detection (0.002-0.08 ng L^-1), and good fiber-to-fiber accuracy (4.3-10.9%) were achieved under optimal conditions. Moreover, the applicability of the developed method was evaluated by analyzing four samples (milk, green tea, tap water, and well water), and the recoveries were in the range of 83.4-101.6%, with relative standard deviations <8.6%. This research extends the application of the stabilized ketoenamine COF as a sample enrichment probe for OCP analysis.

[Recent advance of new sample preparation materials in the analysis and detection of environmental pollutants]

针对复杂样品的分析和痕量目标物的检测,样品前处理是必不可少的,高效的样品前处理技术不仅可以去除或减小样品基质干扰而且能够实现分析物的富集,提高分析检测的准确性和灵敏度。近年来,固相萃取、磁分散固相萃取、枪头固相萃取、搅拌棒萃取、固相微萃取等高效的样品前处理技术已在环境污染物分析检测中获得广泛关注,萃取效率主要取决于萃取材料,所以新型的高效萃取材料一直是样品前处理研究领域的重要发展方向。该文总结和讨论了近年来新型样品前处理材料在环境污染物分析检测中的研究进展,主要聚焦在石墨烯、氧化石墨烯、碳纳米管、无机气凝胶、有机气凝胶、三嗪基功能材料、三嗪基聚合物、分子印迹聚合物、共价有机框架材料、金属有机框架材料以及它们的功能化萃取材料等。这些材料已经被应用于环境样品中不同类别污染物的萃取富集,如重金属离子、多环芳烃、塑化剂、烷烃、苯酚、氯酚、氯苯、多溴联苯醚、全氟磺酸、全氟羧酸、雌激素、药物残留、农药残留等。这些样品前处理材料具有高的表面积、大量的吸附位点,并涉及多种萃取机理如π-π、静电、疏水、亲水、氢键、卤键等相互作用。基于这些萃取材料的多种样品前处理技术与各类检测方法如色谱、质谱、原子吸收光谱、荧光光谱、离子迁移谱等相结合,已广泛应用于环境污染物的高灵敏分析检测。最后,该文总结了样品前处理发展中存在的问题,并展望了其未来在环境分析中的发展趋势。

A novel nanocomposite based on covalent organic polymer and nanocellulose for thin-film microextraction of imipramine from biological samples

A novel covalent organic polymer was prepared using 1,5-diaminonaphthalene as a linker and cyanuric chloride as a node. A thin-film nanocomposite of 1,5-diaminonaphthalene covalent organic polymer and cellulose nanocrystalline was then fabricated via filtering and casting method. The effect of incorporation of various amounts of 1,5-diaminonaphthalene covalent organic polymer and cellulose nanocrystalline was studied to obtain an efficient nanocomposite thin-film with a large number of polar functional groups and high mechanical stability. Field emission scanning electron microscopy, X-ray diffraction, Fourier transform infrared spectrometry, and thermogravimetric analysis techniques were applied for the characterization of physicochemical properties of the prepared materials. Imipramine was determined in the biological samples using thin-film microextraction followed by gas chromatography flame ionization detection. Parameters affecting the extraction efficiency of imipramine were investigated. Under the optimized conditions, the limit of detection was 0.5 ng/mL. Film-to-film reproducibility for three different films fabricated under the same conditions (at three concentration levels) varied between 8.9 and 9.7%. The linear dynamic range covered more than three orders of magnitude (2-5000 ng/mL) with a determination coefficient of 0.9985. The method was successfully applied for preconcentration and determination of imipramine in biological samples with spiking recoveries between 78 and 93%.

Smokeless tobacco analysis: Simultaneous extraction and purification of alkaloids, volatile N-nitrosamines, and polycyclic hydrocarbons for GC-MS/MS

Several smokeless tobacco products are available in the market and comprise complex chemical matrices. Sample preparation for analysis of the multiple classes of harmful compounds in smokeless tobacco products is highly cumbersome. In this study, a simultaneous extraction scheme was developed for three toxic analyte classes in smokeless tobacco products using a two-phase solution consisting of 5% aqueous NaOH and dichloromethane in a 1:4 ratio. The dichloromethane extract was used to analyze four alkaloids directly at levels greater than parts per million; however, passing the layer through a silica cartridge for further purification and concentration was necessary for determining 18 polycyclic aromatic hydrocarbons and four volatile N-nitrosoamines at the ppt level. The multitargets were determined by using gas chromatography with tandem mass spectrometry. The limits of detection for the 18 polycyclic aromatic hydrocarbons, four volatile N-nitrosoamines, three minor alkaloids, and nicotine were 0.2-1.2, 0.2-0.4, 0.6-1.0, and 10.2 μg/g, respectively. Four different smokeless tobacco substrates were fortified with three levels of mixed standards, and the recoveries ranged between 83 and 110%. The method was highly efficient, reduced the sample amounts, solvents, and the time required by approximately 60%. The method was used to assay 18 smokeless tobacco products, and showed potentials in assaying drugs and other plant-based substrates.

Membrane-protected covalent organic framework fiber for direct immersion solid-phase microextraction of 17beta-estradiol in milk

17beta-estradiol (E2) could accumulate in human body through milk and cause various diseases by interfering with the endocrine system. Herein, we coated stainless steel wire with covalent organic framework LZU1 (COF-LZU1) and Nafion protected by dialysis membrane for direct immersion solid phase microextraction (DI-SPME) and coupled with gas chromatography-flame ionization detection (GC-FID) for the detection of trace E2 in milk samples. With dialysis membrane protection, the stability of SPME fiber was improved and the extraction efficiency was only reduced by 7% after repeated use of 160 times. The extraction efficiency of E2 with the home-made fiber COF-LZU1 was 22.1, 8.4, 3.6 times higher than that of bare stainless steel wire, PDMS/DVB and PDMS, respectively. The method had been successfully applied to milk samples, and the relative recoveries were between 77.27% and 108.26%. It can provide an effective and general method for the pretreatment of complex matrix samples.

NiFe2O4-based magnetic covalent organic framework nanocomposites for the efficient adsorption of brominated flame retardants from water

A new kind of NiFe₂O₄-based magnetic covalent organic framework nanocomposites (NiFe₂O₄@COFs) was fabricated through facile synthesis approach under room temperature. The NiFe₂O₄@COFs exhibited higher adsorption capacity for brominated flame retardants than carbon nanotube material based on hydrophobic interactions, π-π stacking interaction, and van der Waals forces. In addition, the adsorption isotherm and the kinetic model were more suitable for Langmuir and pseudo-second-order model, respectively. NiFe₂O₄-based magnetic covalent organic framework nanocomposites combined with HPLC-UV (absorption wavelength: 214 nm) technology has excellent adsorption performance, which exhibited low detection limits (0.03-1.9 μg L^-1), wide linear range (0.11-1000 μg L^-1), good recoveries (91.5-102%) with a relative standard deviation of less than 2.9%. Finally, the prepared magnetic material was successfully used asadsorbents of magnetic solid-phase extraction and applied to the determination of five BFRs from the real water samples. The adsorption and removal of BFRs by NiFe₂O₄@COFs from water samples.

Covalent Organic Frameworks: Synthesis, Properties and Applications-An Overview

Covalent Organic Frameworks (COFs) are an exciting new class of microporous polymers with unprecedented properties in organic material chemistry. They are generally built from rigid, geometrically defined organic building blocks resulting in robust, covalently bonded crystalline networks that extend in two or three dimensions. By strategically combining monomers with specific structures and properties, synthesized COF materials can be fine-tuned and controlled at the atomic level, with unparalleled precision on intrapore chemical environment; moreover, the unusually high pore accessibility allows for easy post-synthetic pore wall modification after the COF is synthesized. Overall, COFs combine high, permanent porosity and surface area with high thermal and chemical stability, crystallinity and customizability, making them ideal candidates for a myriad of promising new solutions in a vast number of scientific fields, with widely varying applications such as gas adsorption and storage, pollutant removal, degradation and separation, advanced filtration, heterogeneous catalysis, chemical sensing, biomedical applications, energy storage and production and a vast array of optoelectronic solutions. This review attempts to give a brief insight on COF history, the overall strategies and techniques for rational COF synthesis and post-synthetic functionalization, as well as a glance at the exponentially growing field of COF research, summarizing their main properties and introducing the numerous technological and industrial state of the art applications, with noteworthy examples found in the literature.

[Synthesis and application progress of covalent organic polymers in sample preparation for food safety analysis]

Food safety is closely related to human health and life. Contaminated foods may result in illness or poisoning. For example, perfluorinated compounds can concentrate in the human body, or they can be transferred to the baby during breastfeeding, thus leading to serious health risks. Phthalate esters may cause damage to the liver, lungs, and kidneys. Therefore, food safety has become a hot topic at a global level. Poisonous and harmful substances in foods are derived from the environment, planting or breeding, food contacting materials, and food processing, or due to unsuitable storage conditions. Residues of pesticides and veterinary drugs, organic pollutants, additives, heavy metals, and biotoxins often hamper food safety, causing diseases or even death. The diversity of available food species, complexity of the sample matrix, and lack of information about the source of pollutants render the direct determination of food contaminants difficult. Pretreatment is vital for the accurate analysis of trace toxins in foods. Optimal pretreatment can not only improve the extract efficiency and determination sensitivity, but also prevent instrument contamination. Pretreatment techniques have played an important role in trace determination for complex matrices. Pretreatment methods can be classified as solvent-based and adsorption-based methods. Adsorption-based techniques such as solid-phase extraction, magnetic solid-phase extraction, and solid-phase microextraction are simple and efficient, and hence, are widely used. In these pretreatment techniques, adsorbents play a key role in the extraction effect. In the last few years, metal organic frameworks, metal oxide materials, carbon nanotubes, graphene, and magnetic nanoparticles, as well as a combination of these materials, have been used as adsorbents. These materials are porous and have a large surface area; they are used to enrich trace targets and eliminate interferents. Covalent organic polymers (COPs) are a class of organic porous materials constructed from organic monomers via covalent bonding. Given their excellent characteristics such as light density, good stability, high surface area, structural controllability, and ease of modification, COPs are potential adsorbents. COPs are often synthesized by solvent thermal methods. However, these methods are time-consuming and require toxic solvents and harsh reaction conditions. As alternatives, room-temperature methods, mechanical chemical methods, microwave-assisted methods, and UV-assisted methods have been developed. This has facilitated the synthesis of a wide range of COPs. In this article, the recent applications of COPs in sample pretreatment for food safety analysis are reviewed. COPs can be used in solid-phase extraction by simple packing into columns, polymerization, or chemical bonding in the capillary. Magnetic compounds have been prepared by one-pot synthesis, in situ growth, in situ reduction, or coprecipitation methods and used in magnetic solid-phase extraction. Coatings of solid-phase microextraction fibers are fabricated by physical methods, chemical bonding, sol-gel methods, or in situ growth. Toxic and harmful substances in foods and foodstuffs are efficiently extracted by exploiting the high adsorbent capacities and specificity of COPs. Future development prospects and challenges in sample pretreatment are also discussed herein. There is increased focus on the development of simple, efficient, and environment-friendly methods to synthesize COPs with specific functions; further, high-throughput, sensitive analytical methods may be established. In the future, more specific COPs will be prepared in a cost-effective manner for widespread use in sample pretreatment.

Electro-enhanced solid-phase microextraction with covalent organic framework modified stainless steel fiber for efficient adsorption of bisphenol A

In this work, electro-enhanced solid-phase microextraction (EE-SPME) and covalent organic framework (COF) were adopted to improve the extraction efficiency. A conductive COF synthesized of 2,6-diaminoanthraquinone (DQ) and 1,3,5-triformylphloroglucinol (TP) was in situ bonded to the stainless steel wire via facile solution-phase approach and used as the EE-SPME fiber coating to preconcentrate a typical endocrine disruptor bisphenol A (BPA). Compared with conventional SPME, the DQTP bonded fiber coupled with EE-SPME device exhibited higher extraction efficiency and achieved extraction equilibrium within 10 min. The proposed approach based on EE-SPME and gas chromatography coupled with flame ionization detector gave a linear range of 0.05-10 μg mL^-1 and detection limit of 3 μg L^-1 (S/N = 3) with good precision (<6.7%) and reproducibility (<7.1%) spiked with 0.1, 0.5, 1.0 μg mL^-1 BPA. Quantitative determination of BPA in extracts of food packagings (mineral water bottles, milk boxes and milk tea cups) was achieved with recoveries from 88.6 to 118.0%.