Sodium dodecyl sulfate-multi-walled carbon nanotubes-coated-membrane solid phase extraction of glucocorticoids in aqueous matrices

Biochar-based polymeric film as sustainable and efficient sorptive phase for preconcentration of steroid hormones in environmental waters and wastewaters

BACKGROUND

The environmental impact of sample preparation should be minimized through simplification of the procedures and the use of natural, renewable and/or reusable materials. In such scenario, thin-film microextraction fulfils the former criteria, as it enables few steps and miniaturization, thus small amount of extraction phase. At the same time, the use of sorbents such as biochars obtained from biomass waste is even more promoted due to their availability at low cost and increased life-cycle in a circular economy vision. However, it is not always easy to combine these criteria in sample preparation.

RESULTS

A thin film microextraction was developed for the determination of steroids in aqueous samples, entailing a membrane made of cellulose triacetate and a wood-derived biochar (Nuchar®) as carbon precursor. Different characterization techniques showed the successful preparation, whereas the sorption kinetics experiments demonstrated that biochar is responsible for the extraction with the polymer acting as a smart support. After a study about membranes' composition in terms of biochar amounts (4 %, 10 %, 16 % wt) and type of synthesis set up, the ceramic 3D-mold was selected, achieving reproducible and ready-to-use membranes with composition fixed as 10 %. Different elution conditions, viz. type and time of agitation, type, composition and volume of eluent, were evaluated. The final microextraction followed by HPLC-MS/MS quantification was successfully validated in river and wastewater treatment plant effluent samples in terms of accuracy (R% 64-123 %, RSD<19 % in river; R% 61-118 %, RSD <18 % in effluent, n = 4), sensitivity (MQLs 0.2-8.5 ng L-1) and robustness.

SIGNIFICANCE

This novel biochar-based polymeric film proved to be a valid and sustainable sorbent, in terms of extraction capability, ease of preparation and greenness. By comparison with literature and the greenness evaluation with the most recent metric tools, this method expands the potential applicability of the thin-film microextraction and opens up innovative scenarios for sustainable procedures entailing the use of biochars entrapped in bio-polymers.

Carbon nanotubes buckypapers: A new frontier in wastewater treatment technology

Occurrence of contaminants in water is one of the major global concerns humanity is still facing today: most of them are extremely toxic and dangerous for human health, obliging their removal for a proper and correct process of sanitation. Among wastewater treatment technologies, in the view of development of sustainable and environmentally friendly processes, membrane adsorption has proved to be a fast and simple method in the removal of pollutants, offering great contaminants recovery percentages, fast adsorbent regeneration and recycle, and easy scale-up. Due to their large surface area and tunable chemistry, carbon nanotubes (CNTs)-based materials revealed to be extraordinary adsorbents, exceeding by far performances of ordinary organic and inorganic membranes such as polyethersulfone, polyvinylidene fluoride, polytetrafluoroethylene, ceramics, currently employed in membrane technologies for wastewater treatment. In consideration of this, the review aims to summarize recent developments in the field of carbon nanotubes-based materials for pollutants recovery from water through adsorption processes. After a brief introduction concerning what adsorption phenomenon is and how it is performed and governed by using carbon nanotubes-based materials, the review discusses into detail the employment of three common typologies of CNTs-based materials (CNTs powders, CNTs-doped polymeric membranes and CNTs membranes) in adsorption process for the removal of water pollutants. Particularly focus will be devoted on the emergent category of self-standing CNTs membranes (buckypapers), made entirely of carbon nanotubes, exhibiting superior performances than CNTs and CNTs-doped polymeric membranes in terms of preparation strategy, recovery percentages of pollutants and regeneration possibilities. The extremely encouraging results presented in this review aim to support and pave the way to the introduction of alternative and more efficient pathways in wastewater treatment technologies to contrast the problem of water pollution.

Green, mildly synthesized bismuth-based MOF for extraction of polar glucocorticoids in environmental water

The complex sample matrix and low environmental concentration make it challenging to effectively determine the polar glucocorticoids. In particular, a green, economical, and environmentally friendly method is urgently needed, since a large amount of extraction solvents, samples, and extraction materials have been commonly used to improve the sensitivity of the reported methods. In this study, a green and robust phenol and bismuth-based MOF of SU101 was mildly synthesized and fabricated as a brand new solid-phase microextraction (SPME) fiber. Only tiny amounts of SU101 and desorption solvents were employed to realize the high-efficiency enrichments of glucocorticoids from water samples. The detection performance of proposed SU101 fiber towards glucocorticoids was much superior to the single-component and multi-component commercial fibers. It indicated that SU101 fiber could be an excellent candidate for the enrichments of polar pharmaceuticals. After it was coupled with the instrument of high performance liquid chromatography tandem mass spectrometry (HPLC-MS/MS), the linear range of 5-10000 ng L-1 with detection limits low to 0.070-1.5 ng L-1 and satisfactory recoveries were achieved by the developed method. Benefiting from the environmental friendliness of SU101 and the less-solvent consumption of SPME technique, this work presented a green and economical strategy for determinations of trace glucocorticoids.

Determination of polyfluoroalkyl substances in cosmetic products using dispersed liquid-liquid extraction coupled with UHPLC-MS/MS

Human exposure to polyfluoroalkyl substances (PFASs) via cosmetics has been of increasing concern due to the tremendous detrimental health impacts of PFASs. Developing an effective method for extracting and determining PFASs in cosmetics is crucial in accurately assessing their corresponding human exposure risk. Herein, this study developed a new sample pre-treatment method to address the challenges posed by the variety and complexity of cosmetic matrices. Seventeen PFASs in cosmetic products, including 9 perfluoro carboxylic acids and 8 perfluorosulfonic acids, were simultaneously determined using ultra-high-performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS). The whole pre-treatment process can be divided into three steps. In step 1, cosmetics with diverse matrix types can be effectively dispersed during extraction by using saturated sodium chloride-acetonitrile and saturated sodium chloride-tetrahydrofuran as extraction solvents. In step 2, the pre-purification step employs a potassium ferrocyanide-zinc acetate co-precipitant to remove high molecular weight interferents from the extraction solution, thereby enhancing the efficiency of solid-phase extraction (SPE). In step 3, WAX-SPE is utilized to further eliminate interferents from the extraction solution while concentrating the analytes, meeting the trace analysis requirements for PFASs in cosmetics. The method detection limits were 0.09-0.26 ng g-1. The recoveries ranged from 70.1% to 114.7%, with relative standard deviations in the range of 2.0-19.1%. The method was applied to cosmetic samples in the Guangzhou market, and the total concentration of PFASs ranged from 0 to 10.8 ng g-1. This method has strong anti-interference ability, good applicability, high sensitivity, and good reproducibility, making it suitable for the analysis and detection of perfluorinated acids in cosmetic samples. It provides technical support for cosmetics safety regulation.

Emerging micropollutants in aquatic ecosystems and nanotechnology-based removal alternatives: A review

There is a significant concern about the accessibility of uncontaminated and safe drinking water, a fundamental necessity for human beings. This concern is attributed to the toxic micropollutants from several emission sources, including industrial toxins, agricultural runoff, wastewater discharges, sewer overflows, landfills, algal blooms and microbiota. Emerging micropollutants (EMs) encompass a broad spectrum of compounds, including pharmaceutically active chemicals, personal care products, pesticides, industrial chemicals, steroid hormones, toxic nanomaterials, microplastics, heavy metals, and microorganisms. The pervasive and enduring nature of EMs has resulted in a detrimental impact on global urban water systems. Of late, these contaminants are receiving more attention due to their inherent potential to generate environmental toxicity and adverse health effects on humans and aquatic life. Although little progress has been made in discovering removal methodologies for EMs, a basic categorization procedure is required to identify and restrict the EMs to tackle the problem of these emerging contaminants. The present review paper provides a crude classification of EMs and their associated negative impact on aquatic life. Furthermore, it delves into various nanotechnology-based approaches as effective solutions to address the challenge of removing EMs from water, thereby ensuring potable drinking water. To conclude, this review paper addresses the challenges associated with the commercialization of nanomaterial, such as toxicity, high cost, inadequate government policies, and incompatibility with the present water purification system and recommends crucial directions for further research that should be pursued.

From polyethylene waste bottles to UIO-66 (Zr) for preconcentration of steroid hormones from river water

Metal-organic framework (UiO-66 (Zr) was synthesized using polyethylene terephthalate (PET) and used as an adsorbent for extraction and preconcentration of steroid hormones in river water. Polyethylene waste bottles were used as the source of polyethylene terephthalate (PET) ligands. The UIO-66(Zr), which the PET was made from recycled waste plastics, was used for the first time for the extraction and preconcentration of four different types of steroid hormones in river water samples. Various analytical characterization techniques were employed to characterize the synthesized material. The steroid hormones were detected and quantified using high-performance liquid chromatography coupled with diode array detector (HPLC-DAD). The results were further validated using ultra-high performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS). Experimental variables, such as sample pH, the mass of adsorbent and extraction time, were optimized using Box-Behnken design (BBD). The dispersive solid phase extraction method combined with HPLC-DAD, displayed good linearity (0.004-1000 µg/L) low limits of detections (LODs, 1.1-16 ng/L for ultrapure water and 2.6-5.3 ng/L for river water) and limits of quantification (LOQs, 3.7-5.3 ng/L for ultrapure water and 8.7-11.0 ng/L for river water samples) and acceptable extraction recoveries (86-101%). The intraday (n = 10) and interday (n = 5) precisions expressed in terms of relative standard deviations (%RSD) were all less than 5%. The steroid hormones were detected in most of the river water samples (Vaal River and Rietspruit River). The DSPE/HPLC method offered a promising approach for simultaneous extraction, preconcentration and determination of steroid hormones in water.

Three-dimensional hydroxylated covalent organic frameworks for solid phase extraction of glucocorticoids in environmental water samples

It is challenging to achieve the highly sensitive detection of glucocorticoids at ultratrace levels because of the abundant hydrophilic groups in their molecules and the complexity of environmental water sample matrices. Here, a highly crystalline three-dimensional hydroxylated covalent organic frameworks (denoted by COF-301) with tetra(4-anilyl)methane (TAM) and 2,5-dihydroxyterephthalaldehyde (DHTA) as building units was constructed and proposed as adsorbent for solid phase extraction (SPE) of glucocorticoids. Theoretical studies were conducted to elucidate the potential adsorption mechanism of glucocorticoids on the COF-301. The COF-301 based SPE combined with liquid chromatography-tandem mass spectrometry provides a promising approach for the preconcentration and determination of glucocorticoids residue in water samples. Good linearity with a correlation coefficient exceeding 0.9988, low limits of detection ranging from 0.024 to 0.075 ng L^-1 and relative standard deviations below 6.68% were achieved. The proposed method was successfully applied to analyze glucocorticoids residue in actual water samples, demonstrating the prospects of this method for the determination of trace glucocorticoids.

Highly efficient amino-functionalized aluminum-based metal organic frameworks mesoporous nanorods for selective extraction of hydrocortisone in pharmaceutical wastewater

Hydrocortisone (HC), as a common steroid hormone drug, is also one of the key intermediates involved in the synthesis of multiple steroid hormone drugs. Residual HC in pharmaceutical wastewater frequently pollutes environmental water as steroid hormone contaminant and possesses great threat to human health as well as sustainable development of the ecosystem. Herein, in order to develop a highly efficient adsorbent system for selective enrichment and detection of HC in pharmaceutical wastewater, a novel amino-functionalized aluminum-based metal organic frameworks (Al-MOFs@NH₂) mesoporous nanorod is fabricated, in which 2-aminoterephthalic acid plays a dual role as organic linker and functional modification unit. The resultant Al-MOFs@NH₂ not only exhibits stable mesoporous structure but also has large specific surface area (849.76 m² g^-1) and plentiful binding sites, which significantly increases the adsorption capacity for HC. Under the promotion of hydrogen bonding and hydrophobic interaction together, Al-MOFs@NH₂ possesses high adsorption capacity (218.53 mg g^-1) for HC, as well as shows satisfactory selectivity for HC and other steroid hormones. Moreover, a method using Al-MOFs@NH₂ as solid phase extraction adsorbents combined with high performance liquid chromatography (HPLC) has been developed to specifically enrich and detect trace amount of HC in pharmaceutical wastewater. The developed method has a low limit of detection (LOD) (0.5×10^-3 μg mL^-1) and shows satisfactory recoveries for HC (75.9%-102.5%) with an acceptable relative standard deviation (RSD). These results demonstrate that the facile one-step preparation and excellent adsorption capacity makes Al-MOFs@NH₂ attractive to capture and remove environmental steroid hormone pollutants. More importantly, the method proposed in this work is expected to provide a prospective solution for analysis of strong bioactive contaminants in pharmaceutical wastewater.

Novel Surfactant-Induced MWCNTs/PDMS-Based Nanocomposites for Tactile Sensing Applications

The paper presents the use of surfactant-induced MWCNTs/PDMS-based nanocomposites for tactile sensing applications. The significance of nanocomposites-based sensors has constantly been growing due to their enhanced electromechanical characteristics. As a result of the simplified customization for their target applications, research is ongoing to determine the quality and quantity of the precursor materials that are involved in the fabrication of nanocomposites. Although a significant amount of work has been done to develop a wide range of nanocomposite-based prototypes, they still require optimization when mixed with polydimethylsiloxane (PDMS) matrices. Multi-Walled Carbon Nanotubes (MWCNTs) are one of the pioneering materials used in multifunctional sensing applications due to their high yield, excellent electrical conductivity and mechanical properties, and high structural integrity. Among the other carbon allotropes used to form nanocomposites, MWCNTs have been widely studied due to their enhanced bonding with the polymer matrix, highly densified sampling, and even surfacing throughout the composites. This paper highlights the development, characterization and implementation of surfactant-added MWCNTs/PDMS-based nanocomposites. The prototypes consisted of an optimized amount of sodium dodecyl sulfonate (SDS) and MWCNTs mixed as nanofillers in the PDMS matrix. The results have been promising in terms of their mechanical behaviour as they responded well to a maximum strain of 40%. Stable and repeatable output was obtained with a response time of 1 millisecond. The Young’s Modulus of the sensors was 2.06 MPa. The utilization of the prototypes for low-pressure tactile sensing applications is also shown here.

Recent advances in micro- and nanomaterial-based adsorbents for pipette-tip solid-phase extraction

There are a lot of review papers of sample pretreatment, but the comprehensive review on pipette-tip solid-phase extraction (PT-SPE) is lacking. This review (133 references) is mainly devoted to the development of different types of micro- and nanosorbent-based PT-SPE, including silica materials, carbon materials, organic polymers, molecularly imprinted polymers, and metal-organic frameworks. Each section mainly introduces and discusses the preparation methods, advantages and limitations of adsorbents, and their applications to environmental, biological, and food samples. This review also demonstrates the advantages of PT-SPE like convenience, speed, less organic solvent, and low cost. Finally, the future application and development trend of PT-SPE are prospected.

Development of a surfactant-assisted dispersive solid phase extraction using deep eutectic solvent to extract four tetracycline antibiotics residues in milk samples

In this study, a new floating dispersive solid phase extraction method based on deep eutectic solvents has been developed in a home-made extraction device for the extraction of four tetracycline antibiotics from milk samples. In this approach, the sorbent (activated carbon) was dispersed in whole parts of solution with the aid of air stream and floated on top of the solution with the aid of the surfactant (lauryl betaine) and air bubbles. After collection of the sorbent, the adsorbed analytes were eluted with tetrabutyl ammonium chloride-propionic acid deep eutectic solvent under sonication. In this method, there was no need of organic dispersive and extraction solvents and the used sorbent was collected on top of the solution and collected without centrifugation. The validation parameters showed that low limits of detection (0.1-0.3 μg/kg) and quantification (0.6-1.0 μg/kg), acceptable enrichment factors (52-60), efficient extraction recoveries (80-91%), and satisfactory relative standard deviations (≤9.8%) were obtained. Eventually, the method was successfully applied on different milk samples and tetracycline was determined in them.