Chemical water monitoring under the Water Framework Directive with Certified Reference Materials

A journey towards whole water certified reference materials for organic substances: measuring polycyclic aromatic hydrocarbons as required by the European Union Water Framework Directive

In 2000, the Water Framework Directive (WFD) came into force in the European Union with the aim of protecting and improving water quality. The priority substances established to be monitored are predominantly organic compounds, for which the WFD sets the requirement of 'whole water sample' analysis. This legislative requirement poses analytical challenges for the monitoring laboratories as well as technical challenges for reference materials producers. In the past, there were attempts to produce reference materials as quality assurance/quality control tools for measuring organic priority substances in whole water. A critical reflection on the approaches and solutions applied to prepare such kind of matrix reference materials is presented along with a discussion on the difficulties encountered by the analytical laboratories in analysing such complex matrices. The Certified Reference Material (CRM) ERM-CA100 can be considered as a pioneer for a 'whole water' CRM (containing humic acids) and has been designed for the analysis of polycyclic aromatic hydrocarbons (PAHs). Further developments seem to be necessary to upgrade the design towards a CRM which will also include suspended particulate matter, another basic constituent of natural surface water samples.

Ultra-trace determination of total mercury in Italian bottled waters

Mercury (Hg) is a widespread, highly toxic persistent pollutant with adverse health effects on humans. So far, concentrations below the method detection limit have always been reported by studies on the concentration of mercury in bottled water when determined using instrumental analytical methods. These are often very expensive and are unaffordable for many laboratories. In this work, a less expensive method based on cold vapour atomic fluorescence spectrometry has been employed to determine total mercury (Hg_T) concentrations in bottled natural mineral waters. In all, 255 waters representing 164 different typologies were analysed. They came from 136 springs located in 18 Italian regions. In all samples, Hg_T concentrations were found in the range of sub-nanogram to a few nanograms per litre, well below the National and European regulatory limit (1 μg L^-1). Differences in Hg_T concentrations were related not only to the environmental characteristics of the springs but also to the extent and impact of human activities. Higher concentrations were found in waters coming from regions with former mining and/or natural thermal and volcanic activity. These data allowed us to estimate the mercury intake by population (adults, children and toddlers) from drinkable mineral waters consumption. The mean mercury daily intake was found to be remarkably lower, not only than the provisional tolerable value (1 μg L^-1 according to European and Italian legislation) but also than the estimated provisional tolerable weekly intake (PTWI) value (4 μg kg^-1 body weight) recommended by the Joint FAO/WHO Expert Committee on Food Additives (JECFA).

Study of the degradation of butyltin compounds in surface water samples under different storage conditions using multiple isotope tracers and GC-MS/MS

The degradation of butyltin compounds in surface water samples under different storage conditions has been studied. A triple spike solution, containing monobutyltin (MBT), dibutyltin (DBT) and tributyltin (TBT) labelled with a different tin isotope, was added to the sample to calculate the extent of the interconversion reactions among butyltin compounds. Real surface water samples (river water) were collected and stored in glass, polypropylene or polytetrafluoroethylene (PTFE) containers. The presence of light, addition of acetic acid, storage temperature (22, 4 or -18 °C), and the influence of a filtration step were evaluated. Moreover, Milli-Q water with and without the addition of a high concentration of humic acids was prepared in parallel and the results compared to those obtained from the real samples. The water samples were analysed by gas chromatography-tandem mass spectrometry (GC-MS/MS) in selected reaction monitoring (SRM) mode at two different storage times (2 weeks and 4 months after its preparation) to carry out both a short- and a long-term stability study. The lowest butyltin degradation was obtained when the samples were stored at -18 °C in the dark. Under these conditions, both TBT and DBT showed negligible dealkylation factors after 2 weeks. After 4 months, DBT dealkylation to MBT increased up to 19 % but TBT degradation was not observed.

Passive Sampling in Regulatory Chemical Monitoring of Nonpolar Organic Compounds in the Aquatic Environment

We reviewed compliance monitoring requirements in the European Union, the United States, and the Oslo-Paris Convention for the protection of the marine environment of the North-East Atlantic, and evaluated if these are met by passive sampling methods for nonpolar compounds. The strengths and shortcomings of passive sampling are assessed for water, sediments, and biota. Passive water sampling is a suitable technique for measuring concentrations of freely dissolved compounds. This method yields results that are incompatible with the EU's quality standard definition in terms of total concentrations in water, but this definition has little scientific basis. Insufficient quality control is a present weakness of passive sampling in water. Laboratory performance studies and the development of standardized methods are needed to improve data quality and to encourage the use of passive sampling by commercial laboratories and monitoring agencies. Successful prediction of bioaccumulation based on passive sampling is well documented for organisms at the lower trophic levels, but requires more research for higher levels. Despite the existence of several knowledge gaps, passive sampling presently is the best available technology for chemical monitoring of nonpolar organic compounds. Key issues to be addressed by scientists and environmental managers are outlined.

Development and validation of a method for mercury determination in seawater for the process control of a candidate certified reference material

A simple, robust and reliable method for mercury determination in seawater matrices based on the combination of cold vapour generation and inductively coupled plasma mass spectrometry (CV-ICP-MS) and its complete in-house validation are described. The method validation covers parameters such as linearity, limit of detection (LOD), limit of quantification (LOQ), trueness, repeatability, intermediate precision and robustness. A calibration curve covering the whole working range was achieved with coefficients of determination typically higher than 0.9992. The repeatability of the method (RSDrep) was 0.5 %, and the intermediate precision was 2.3 % at the target mass fraction of 20 ng/kg. Moreover, the method was robust with respect to the salinity of the seawater. The limit of quantification was 2.7 ng/kg, which corresponds to 13.5 % of the target mass fraction in the future certified reference material (20 ng/kg). An uncertainty budget for the measurement of mercury in seawater has been established. The relative expanded (k = 2) combined uncertainty is 6 %. The performance of the validated method was demonstrated by generating results for process control and a homogeneity study for the production of a candidate certified reference material.

Novel concepts for preparation of reference materials as whole water samples for priority substances at nanogram-per-liter level using model suspended particulate matter and humic acids

One of the unresolved issues of the European Water Framework Directive is the unavailability of realistic water reference materials for the organic priority pollutants at low nanogram-per-liter concentrations. In the present study, three different types of ready-to-use water test materials were developed for polycyclic aromatic hydrocarbons (PAHs), polybrominated diphenyl ethers (PBDEs) and tributyltin (TBT) at nanogram-per-liter levels. The first type simulated the dissolved phase in the water and comprised of a solution of humic acids (HA) at 5 mg L(-1) dissolved organic carbon (DOC) and a spike of the target compounds. The second type of water sample incorporated the particulate phase in water. To this end, model suspended particulate matter (SPM) with a realistic particle size was produced by jet milling soil and sediments containing known amounts of PAHs, PBDEs and TBT and added as slurry to mineral water. The most complex test materials mimicked "whole water" consequently containing both phases, the model SPM and the HA solution with the target analytes strongly bound to the SPM. In this paper, the development of concepts, processing of the starting materials, characterisation of the HA and model SPMs as well as results for homogeneity and stability testing of the ready-to-use test materials are described in detail.