Liquid-phase microextraction techniques based on ionic liquids for preconcentration and determination of metals

Development of a rapid method for extraction of uranium from uranium bearing materials using ionic liquid as extracting agent from basic media

The paper presents the development of a rapid method for the direct determination of uranium using liquid scintillation analysis in uranium bearing materials with different uranium concentrations and with different impurity levels (U-ore, Uranium ore concentrate (UOC) and U-metal). Uranium extraction was carried out using hydrophobic ionic liquid Aliquat-336 thiosalicylate, ([A-336][TS]) from diluted samples in basic medium followed by liquid scintillation counting (LSC). Extraction efficiencies for uranium from aqueous medium was studied with very small volumes of ionic liquid under varying volume, pH and uranium concentration of the aqueous medium. Maximum extraction efficiency was achieved near pH 8-11. Uranium was successfully re-extracted from organic medium with nitric acid and electroplated onto stainless steel planchette for alpha spectrometry determination. Maximum re-extraction efficiency with 1 M HNO₃ combined with electroplating efficiency observed was 80%. The methodology was applied for real samples. The uranium extraction efficiency using ionic liquid was about 85% for U-metal and UOC samples with comparatively low impurity level; whereas extraction efficiency for U-ore samples was found to be less than 40%. The technique can be applied for nuclear forensic applications as well as nuclear emergency scenarios for a quick initial assessment and isotopic analysis of uranium in the samples.

Simultaneous and highly sensitive determination of selenium and tellurium species in environmental samples by on-line ionic liquid based in-situ solvent formation microextraction with hydride generation atomic fluorescence spectrometry detection

A novel on-line preconcentration and speciation analysis method for the simultaneous determination of inorganic Se and Te species is presented in this work. The methodology is based on the on-line formation of a hydrophobic ionic liquid (IL) directly in the liquid sample stream of a flow injection system, thus achieving an efficient and rapid extraction of the analytes complexed with ammonium pyrrolidine dithiocarbamate into the finely dispersed extractant droplets, that were then retained in a column filled with cotton. A full study of the chemical and hydrodynamical parameters was developed, including the right selection of the IL used as extractant and its concentration, pH, complexing reagent, sample and ion-exchange reagent volumes and column design. Additionally, a miniaturized external hydride generator was adapted to the spectrometer in order to increase the sensitivity of the atomic fluorescence measurements using only 250 μL of 5 mol L^-1 HNO₃ in methanol as eluent. The analytical figures of merit obtained for 15 mL of sample included sensitivity enhancement factors of 71, 70, 49 and 40 for Te(IV), Te(VI), Se(IV) and Se(VI), respectively, and limits of detection of 1.8 ng L^-1 for both Te species, 2.6 ng L^-1 for Se(IV) and 3.2 ng L^-1 for Se(VI). After optimization, the method was successfully applied for the analysis of environmental samples: soils and sediments, as well as sea, river, underground and tap water.

A Critical Study of the Effect of Polymeric Fibers on the Performance of Supported Liquid Membranes in Sample Microextraction for Metals Analysis

Popularity of hollow fiber-supported liquid membranes (HF-SLM) for liquid-phase microextraction (HF-LPME) has increased in the last decades. In particular, HF-SLM are applied for sample treatment in the determination and speciation of metals. Up to the date, optimization of preconcentration systems has been focused on chemical conditions. However, criteria about fiber selection are not reflected in published works. HFs differ in pore size, porosity, wall thickness, etc., which can affect efficiency and/or selectivity of chemical systems in extraction of metals. In this work, Ag+ transport using tri-isobutylphosphine sulfide (TIBPS) has been used as a model to evaluate differences in metal transport due to the properties of three different fibers. Accurel PP 50/280 fibers, with a higher effective surface and smaller wall thickness, showed the highest efficiency for metal transport. Accurel PP Q3/2 exhibited intermediate efficiency but easier handling and, finally, Accurel PP S6/2 fibers, with a higher wall thickness, offered poorer efficiency but the highest stability and capability for metal speciation. Summarizing, selection of the polymeric support of HF-SLM is a key factor in their applicability of LPME for metals in natural waters.

Novel Room Temperature Ionic Liquid for Liquid-Phase Microextraction of Cannabidiol from Natural Cosmetics

This study presents the synthesis of a novel asymmetric 1,3-di(alkoxy)imidazolium based room temperature ionic liquid, more precisely 1-butoxy-3-ethoxy-2-ethyl-imidazolium bis(trifluoromethane)sulfonimide, and its application as an extraction solvent in liquid-phase microextraction of cannabidiol from natural cosmetics. Quantification was implemented, using a high performance liquid chromatography system coupled to ultraviolet detection. Molecular structure elucidation was performed by nuclear magnetic resonance spectroscopy. The extraction procedure was optimized by means of two different design of experiments. Additionally, a full validation was executed. The established calibration model, ranging from 0.6 to 6.0 mg g−1, was linear with a coefficient of determination of 0.9993. Accuracy and precision were demonstrated on four consecutive days with a bias within −2.6 to 2.3% and a maximum relative standard deviation value of 2.5%. Recoveries, tested for low and high concentration within the calibration range, were 80%. Stability of extracted cannabidiol was proven for three days at room temperature and fourteen days at 4 °C and −20 °C. An autosampler stability for 24 h was validated. Liquid-phase microextraction of cannabidiol from different formulated cream based cosmetics was performed, including four ointments and four creams. The results show that a significantly higher selectivity could be achieved compared to a conventional extraction methods with methanol.

Ligandless, deep eutectic solvent-based ultrasound-assisted dispersive liquid-liquid microextraction with solidification of the aqueous phase for preconcentration of lead, cadmium, cobalt and nickel in water samples

A green and efficient sample preparation method using a deep eutectic solvent-based ultrasounds-assisted dispersive liquid-liquid microextraction with solidification of the aqueous phase followed by high performance liquid chromatography analysis was developed for preconcentration and determination of heavy metals in environmental samples. In the proposed method, a novel, low density deep eutectic solvent was prepared by mixing trihexyl(tetradecyl)phosphonium chloride and thiosalicylic acid at a molar ratio of 1:2 and used both as an extractant and complexing agent. Ultrasound was used to disperse the extractant in the aqueous phase of the sample. Then, the phases were separated by centrifugation, after which the aqueous phase was frozen and the surface extractant phase was dissolved in a small volume of acetonitrile and subjected to liquid chromatographic analysis. The proposed method provided precisions (relative standard deviation, n = 5) in the range of 2.6-4.7%. The limit of detection were 0.05, 0.13, 0.06, and 0.11 µg/L for Pb(II), Cd(II), Co(II), Ni(II), respectively. The enhancement factors were equal to 154, 159, 162, and 158 for lead(II), cadmium(II), cobalt(II), and nickel(II), respectively. The accuracy of the proposed method was evaluated using certified reference materials (CA011b - hard drinking water, NIST 1643e - trace elements in water, TMRAIN-04 - simulated rain sample).

Microwave-assisted ionic liquid-based micelle extraction combined with trace-fluorinated carbon nanotubes in dispersive micro-solid-phase extraction to determine three sesquiterpenes in roots of Curcuma wenyujin

INTRODUCTION

Germacrone, furanodiene and β-elemene are the representative bioactive compounds in Curcuma species. The conventional extraction methods of these three sesquiterpenes are usually time-consuming and require a large volume of hazardous organic solvents. Thus, a fast and reliable method for extracting these sesquiterpenes from Curcuma plant is required urgently.

OBJECTIVE

To establish a novel and simple extraction method for quantitative analysis of small amounts of sesquiterpenes in C. wenyujin plant.

METHODOLOGY

A method using microwave-assisted ionic liquid-micelle extraction combined with dispersive micro-solid-phase extraction (DMSPE) has been proposed for the extraction of three sesquiterpenoids in Curcuma plant. Fluorinated carbon nanotubes (FCNTs) were used as an adsorbent in DMSPE for the first time. Parameters concerning the microwave-assisted extraction (MAE) conditions and the DMSPE were investigated and evaluated to achieve optimum extraction efficiency of target analytes.

RESULTS

The final conditions of ionic liquid-micelle based MAE were selected to be 0.25 M of 1-decyl-3-vinylimidazolium bromide as the extraction solvent, microwave irradiation for 10 min at 60°C. And the optimal DMSPE conditions were found to be 2 μg/mL of FCNTs as the adsorbent, extraction time of 2 min and 100 μL of acetonitrile as the elution solvent. The developed method exhibited good linearities (R > 0.9990), high repeatability and recoveries. The proposed method has been successfully applied in determination of sesquiterpenes in C. wenyujin samples.

CONCLUSION

The work shows a potential in analysing small amounts of sesquiterpenes in complex samples and represents the first attempt of using FCNTs as an adsorbent for the microextraction mode.

Determination of Mercury(II) on A Centrifugal Microfluidic Device Using Ionic Liquid Dispersive Liquid-Liquid Microextraction

An integrated centrifugal microfluidic device was developed to preconcentrate and detect hazardous mercury (II) in water with ionic liquid as environmentally friendly extractant. An automatically salt-controlled ionic liquid dispersive liquid–liquid microextraction on a centrifugal microfluidic device was designed, fabricated, and characterized. The entire liquid transport mixing and separation process was controlled by rotation speed, siphon valves, and capillary valves. Still frame images on the rotating device showed the process in detail, revealing the sequential steps of mixing, siphon priming, transportation between chambers, and phase separation. The preconcentration of red dye could be clearly observed with the naked eye. By combining fluorescence probe and microscopy techniques, the device was tested to determine ppb-level mercury (II) in water, and was found to exhibit good linearity and low detection limit.

Multi-elemental ionic liquid-based solvent bar micro-extraction of priority and emerging trace metallic pollutants (Cd, Ag, Pd) in natural waters

Transition metals Cd, Pd and Ag are toxic even at very low concentration. Cd is considered a priority substance; while, Pd and Ag are emerging pollutants. Membrane technologies have been applied for their extraction; however, they require important amounts of reagents, time and energy. Additionally, effective reagents for metal extraction in saline natural waters are limited. In this case, hollow fiber liquid phase micro-extraction with a configuration of solvent bar (SBME) using the ionic liquid Cyphos® 101 as extractant is proposed. Optimized conditions for SBME of Cd, Ag and Pd were 50% Cyphos® 101 in the organic solution, extraction time 30 min and 800 rpm stirring rate. Leaching was in all cases lower than 0.1%. Metallic concentrations were measured by flame atomic absorption spectroscopy. The method was applied to the extraction of Ag, Cd and Pd in natural water samples. Except for waste water, Pd extraction was higher than 90% in all cases. Cd (≈100%) and Ag (93-95%) offered their best results for saline samples. Concluding, the proposed system is a low cost and green methodology that allows a simple and fast extraction of trace pollutants such as Ag, Cd and Pd in different natural waters, including highly saline samples.

Selective ionic liquid solvent bar micro-extraction for estimation of ultra-trace silver fractions in marine waters

Ag can be found in the ocean at the ultra-trace level, mainly as AgCl_n^(n-1)- and complexed by dissolved organic matter (Ag-DOM). However, methods for studying Ag speciation in marine waters are limited by the lack of extractants capable to separate organic and inorganic silver species in natural conditions of seawater samples. In this work, a two-phase solvent bar micro-extraction method using the ionic liquid trihexyltetradecylphosphonium chloride (Cyphos® 101) was applied for selective micro-extraction of AgCl_n^(n-1)- from organic silver in marine waters, working at seawater pH,. The application to real samples was performed under the following conditions: 2.5% Cyphos® 101 in kerosene solution with 10% dodecan-1-ol inside the fiber, and 30 min of sample extraction at a stirring rate of 800 rpm. The proposed SBME was successfully used for estimation of Ag fractions in waters from the Bay of Cádiz (South-west Spain) showing its applicability for a simple, fast and environmentally friendly speciation of silver in marine water samples. The method presented a linear response up to 500 ng L^-1 and a detection limit of 0.4 ng L^-1, using GF-AAS for instrumental determination.

Solvent Bar Micro-Extraction of Heavy Metals from Natural Water Samples Using 3-Hydroxy-2-Naphthoate-Based Ionic Liquids

Developments in the liquid micro-extraction of trace metals from aqueous phases have proven to be limited when extended from pure water to more complex and demanding matrices such as sea water or wastewater treatment effluents. To establish a system that works under such matrices, we successfully tested three task-specific ionic liquids, namely trihexyltetradecyl- phosphonium-, methyltrioctylphosphonium- and methyltrioctylammonium 3-hydroxy-2-naphthoate in two-phase solvent bar micro-extraction (SBME) experiments. We describe the influence of pH, organic additives, time, stirring rate and volume of ionic liquid for multi-elemental micro-extraction of Cu, Ag, Cd and Pb from various synthetic and natural aqueous feed solutions. Highest extraction for all metals was achieved at pH 8.0. Minimal leaching of the ionic liquids into the aqueous phase was demonstrated, with values < 30 mg L⁻¹ DOC in all cases. Sample salinities of up to 60 g L⁻¹ NaCl had a positive effect on the extraction of Cd, possibly due to an efficient extraction mechanism of the present chlorido complexes. In metal-spiked natural feed solutions, the selected SBME setups showed unchanged stability under all conditions tested. We could efficiently (≥85%) extract Cu and Ag from drinking water and achieved high efficacies for Ag and Cd from natural sea water and hypersaline water, respectively. The method presented here proves to be a useful tool for an efficient SBME of heavy metals from natural waters without the need to pretreat or modify the sample.

Detection of Polycyclic Aromatic Hydrocarbons in Water Samples by Annular Platform-Supported Ionic Liquid-Based Headspace Liquid-Phase Microextraction

In this paper, a new method of annular platform-supported headspace liquid-phase microextraction (LPME) was designed using ionic liquid as an extraction solvent, wherein extraction stability and efficiency were improved by adding an annular platform inside the extraction bottle. The ionic liquid 1-silicyl-3-benzylimidazolehexafluorophosphate was first synthesized and proved to be an excellent extraction solvent. Coupled with liquid chromatography, the proposed method was employed to analysis of polycyclic aromatic hydrocarbons (PAHs) in water and optimized in aspects of extraction temperature, extraction solvent volume, extraction time, pH, stirring rate, and salt effect of solution. The results indicated that this method showed good linearity (R ² > 0.995) within 0.5 µg·L^-1 to 1000 µg·L^-1 for PAHs. The method was more suitable for extraction of volatile PAHs, with recoveries from 65.0% to 102% and quantification limits from 0.01 to 0.05 µg·L^-1. It has been successfully applied for detection of PAHs in seawater samples.

Ultrasound-assisted emulsification–microextraction and spectrophotometric determination of cobalt, nickel and copper after optimization based on Box-Behnken design and chemometrics methods

A fast, simple, and economical method for extraction, preconcentration and determination of cobalt, nickel and copper as their 1-(2-pyridilazo) 2-naphthol (PAN) complexes based on ultrasound-assisted emulsification–microextraction (USAEME) and multivariate calibration of spectrophotometric data is presented. Various parameters affecting the extraction efficiency were optimized both with univariate and Box–Behnken design. The resolution of ternary mixtures of these metallic ions was accomplished by using partial least-squares regression (PLS), orthogonal signal correction-partial least-squares regression (OSC-PLS), and orthogonal signal correction-genetic algorithmspartial least-squares regression (OSC-GA-PLS). Under the optimum conditions, the calibration graphs were linear in the range of 2.0–150.0, 2.0–120.0 and 2.0–150.0 ng mL−1 for Co2+, Ni2+, and Cu2+, respectively, with a limit of detection of 0.14 (Co2+), 0.13 (Ni2+) and 0.14 ng mL−1 (Cu2+) and the relative standard deviation was <2.5%. The method was successfully applied to the simultaneous determination of these cations in different samples.

Preconcentration of Trace Neonicotinoid Insecticide Residues Using Vortex-Assisted Dispersive Micro Solid-Phase Extraction with Montmorillonite as an Efficient Sorbent

In this work, we investigated montmorillonite for adsorption of neonicotinoid insecticides in vortex-assisted dispersive micro-solid phase extraction (VA-d-μ-SPE). High-performance liquid chromatography with photodiode array detection was used for quantification and determination of neonicotinoid insecticide residues, including thiamethoxam, clothianidin, imidacloprid, acetamiprid, and thiacloprid. In this method, the solid sorbent was dispersed into the aqueous sample solution and vortex agitation was performed to accelerate the extraction process. Finally, the solution was filtered from the solid sorbent with a membrane filter. The parameters affecting the extraction efficiency of the proposed method were optimized, such as amount of sorbent, sample volume, salt addition, type and volume of extraction solvent, and vortex time. The adsorbing results show that montmorillonite could be reused at least 4 times and be used as an effective adsorbent for rapid extraction/preconcentration of neonicotinoid insecticide residues. Under optimum conditions, linear dynamic ranges were achieved between 0.5 and 1000 ng mL^-1 with a correlation of determination (R²) greater than 0.99. Limit of detection (LOD) ranged from 0.005 to 0.065 ng mL^-1, while limit of quantification (LOQ) ranged from 0.008 to 0.263 ng mL^-1. The enrichment factor (EF) ranged from 8 to 176-fold. The results demonstrated that the proposed method not only provided a more simple and sensitive method, but also can be used as a powerful alternative method for the simultaneous determination of insecticide residues in natural surface water and fruit juice samples.

Zwitterion-functionalized polymer microspheres as a sorbent for solid phase extraction of trace levels of V(V), Cr(III), As(III), Sn(IV), Sb(III) and Hg(II) prior to their determination by ICP-MS

This paper describes the preparation of zwitterion-functionalized polymer microspheres (ZPMs) and their application to simultaneous enrichment of V(V), Cr(III), As(III), Sn(IV), Sb(III) and Hg(II) from environmental water samples. The ZPMs were prepared by emulsion copolymerization of ethyl methacrylate, 2-diethylaminoethyl methacrylate and triethylene glycol dimethyl acrylate followed by modification with 1,3-propanesultone. The components were analyzed by elemental analyses as well as Fourier transform infrared spectroscopy, and the structures were characterized by scanning electron microscopy and transmission electron microscopy. The ZPMs were packed into a mini-column for on-line solid-phase extraction (SPE) of the above metal ions. Following extraction with 40 mM NH₄NO₃ and 0.5 M HNO₃ solution, the ions were quantified by ICP-MS. Under the optimized conditions, the enrichment factors (from a 40 mL sample) are up to 60 for the ions V(V), As(III), Sb(III) and Hg(II), and 55 for Cr(III) and Sn(IV). The detection limits are 1.2, 3.4, 1.0, 3.7, 2.1 and 1.6 ng L^-1 for V(V), Cr(III), As(III), Sn(IV), Sb(III) and Hg(II), respectively, and the relative standard deviations (RSDs) are below 5.2%. The feasibility and accuracy of the method were validated by successfully analyzing six certified reference materials as well as lake, well and river waters. Graphical abstract Zwitterion-functionalized polymer microspheres (ZPMs) were prepared and packed into a mini-column for on-line solid-phase extraction (SPE) via pump 1. Then V(V), Cr(III), As(III), Sn(IV), Sb(III) and Hg(II) ions in environmental waters were eluted and submitted to ICP-MS via pump 2.

Ionic liquid ultrasound-assisted dispersive liquid-liquid microextraction based on solidification of the aqueous phase for preconcentration of heavy metals ions prior to determination by LC-UV

Ionic liquid ultrasound-assisted dispersive liquid-liquid microextraction based on solidification of the aqueous phase was used for preconcentration of Ni²⁺, Co²⁺, Cd²⁺, Cu²⁺, Pb²⁺ in natural water samples prior to liquid chromatography with UV detection. In the proposed method, the ammonium pyrrolidinedithiocarbamate was used as a complexing agent and the phosphonium ionic liquid trihexyl(tetradecyl)phosphonium bis[(2,4,4-trimethyl)pentyl]phosphinate (Cyphos IL 104) was used as an extractant. Ultrasound energy was used to disperse the extractant in the aqueous phase. After microextraction, the ionic liquid and aqueous phases were separated by centrifugation. Then the aqueous phase was frozen and the lighter than water ionic liquid phase containing metal ions complexes with pyrrolidinedithiocarbamate was separated and dissolved in a small volume of methanol prior to injection into the liquid chromatograph. Several parameters including the volume of extractant, the pH of the sample, the concentration of complexing agent, the time of ultrasound energy treatment, the time and speed of centrifugation and the effect of ionic strength were optimized. Under the optimized conditions (10 µL of Cyphos IL 104, pH = 5, 0.3% w/v ammonium pyrrolidinedithiocarbamate, 60 s of ultrasound use, 5 min/5000 rpm (2516×g) of centrifugation, 2.0 mg of NaCl), preconcentration factors were 211, 210, 209, 207 and 211 for Ni²⁺, Co²⁺, Cd²⁺, Cu²⁺ and Pb²⁺ respectively. Linearity was observed in the ranges 0.2-75.0 µg L^-1 for Pb²⁺, Cd²⁺, Co²⁺ and 0.5-100.0 µg L^-1 for Cu²⁺, Ni²⁺. The limits of detection were 0.03 µg L^-1 for Ni²⁺, 0.03 µg L^-1 for Co²⁺, 0.03 µg L^-1 for Cd²⁺, 0.02 µg L^-1 for Cu²⁺, 0.02 µg L^-1 for Pb²⁺, respectively. The accuracy of this method was evaluated by preconcentration and determination of Ni²⁺, Co²⁺, Cd²⁺, Cu²⁺, Pb²⁺ in certified reference materials (TMRAIN-04 and NIST 1643e) with the recovery values in the range of 97-102%. The presented method has been successfully applied for the determination of analytes in natural water samples (river and lake waters).

Ionic liquid solvent bar micro-extraction of CdCln(n-2)- species for ultra-trace Cd determination in seawater

Water analysis of trace metals has been benefited by recent studies on sample preparation by liquid micro-extraction. However, there are still limitations for its application to seawater, such as the need of additives to preserve the sample or the availability of chemical extractants for the selective extraction from highly saline samples. In this work, a three phase solvent bar micro-extraction (3SBME) system containing the ionic liquid trioctylmethylammonium chloride (Aliquat^® 336) has been used for isolation and pre-concentration of Cd from seawater samples, due to its ability for ionic exchange of CdCl_n^(n-2)-. The system was optimized to work at the natural pH of seawater, and conditions for application to real samples were 0.18 M Aliquat^® 336 dissolved in kerosene with 0.25 M dodecan-1-ol as organic solution, 1.5 M HNO₃ as acceptor solution, 60 min extraction time, and 800 rpm stirring speed in the sample. Loss of organic solution into the sample during extraction was evaluated and revealed its dependence on stirring rate and extraction time. Under optimum conditions samples containing Cd 0.09-0.90 nM were pre-concentrated 65 times. GF-AAS was used for metal quantification with a limit of detection of 0.04 nM. Accuracy was successfully evaluated measuring Cd in a seawater certified reference material BCR-403.