A systematic review and meta-analysis of voltammetric and optical techniques for inorganic selenium determination in water

A modified selective optical sensor for selenium determination based on incorporating xylenol orange in a poly(vinyl chloride) membrane

A novel optical sensor has been developed to measure selenium ions. The sensor membrane was created by mixing xylenol orange (XO) and sodium tetraphenylborate (NaTPB) with a plasticized poly(vinyl chloride) membrane that contained o-nitrophenyl octyl ether (o-NPOE) as a plasticizer. XO was previously established for use in a colorimeter to measure selenium in water and other media. At pH 6.6, the color of the detecting membrane changed from orange to pink when in contact with Se4+ ions. Various variables affecting the uptake efficiency were evaluated and optimized. Under optimum conditions (i.e., 30% PVC, 60% o-NPOE, and 5.0% of both XO and NaTPB for 5.0 min as the response time), the proposed sensor displayed a linear range 10-175 ng mL-1 with the detection and quantification limits of 3.0 and 10 ng mL-1, respectively. Also, the precision (RSD%) was better than 2.2% for six replicate determinations of 100 ng mL-1 Se4+ in various membranes. For the detection of Se4+, the selectivity of the sensor membrane was investigated for a number of possible interfering inorganic cations, but no appreciable interference was found. With the use of a 0.3 M HCl solution, the sensor was successfully restored, and the response that may have been reversible and reproducible exhibited an RSD% of less than 2.0%. The sensor has been successfully used to analyze Se4+ ions in environmental and biological materials.

A critical analysis of sources, pollution, and remediation of selenium, an emerging contaminant

Selenium (Se) is an essential metalloid and is categorized as emerging anthropogenic contaminant released to the environment. The rise of Se release into the environment has raised concern about its bioaccumulation, toxicity, and potential to cause serious damages to aquatic and terrestrial ecosystem. Therefore, it is extremely important to monitor Se level in environment on a regular basis. Understanding Se release, anthropogenic sources, and environmental behavior is critical for developing an effective Se containment strategy. The ongoing efforts of Se remediation have mostly emphasized monitoring and remediation as an independent topics of research. However, our paper has integrated both by explaining the attributes of monitoring on effective scale followed by a candid review of widespread technological options available with specific focus on Se removal from environmental media. Another novel approach demonstrated in the article is the presentation of an overwhelming evidence of limitations that various researchers are confronted with to overcome achieving effective remediation. Furthermore, we followed a holistic approach to discuss ways to remediate Se for cleaner environment especially related to introducing weak magnetic field for ZVI reactivity enhancement. We linked this phenomenal process to electrokinetics and presented convincing facts in support of Se remediation, which has led to emerge 'membrane technology', as another viable option for remediation. Hence, an interesting, innovative and future oriented review is presented, which will undoubtedly seek attention from global researchers.

Bioconversion of inorganic selenium to less toxic selenium forms by microbes: A review

In recent years, microbial conversion of inorganic selenium into an efficient and low-toxic form of selenium has attracted much attention. With the improvement of scientific awareness and the continuous progress of nanotechnology, selenium nanoparticles can not only play the unique functions of organic selenium and inorganic selenium but also have higher safety, absorption and biological activity than other selenium forms. Therefore, the focus of attention has gradually shifted beyond the level of selenium enrichment in yeast to the combination of biosynthetic selenium nanoparticles (BioSeNPs). This paper primarily reviews inorganic selenium and its conversion to less toxic organic selenium and BioSeNPs by microbes. The synthesis method and potential mechanism of organic selenium and BioSeNPs are also introduced, which provide a basis for the production of specific forms of selenium. The methods to characterize selenium in different forms are discussed to understand the morphology, size and other characteristics of selenium. In general, to obtain safer and higher selenium content products, it is necessary to develop yeast resources with higher selenium conversion and accumulation.

Properties and Characterization Techniques of Graphene Modified Asphalt Binders

Graphene is a carbon-based nanomaterial used in various industries to improve the performance of hundreds of materials. For instance, graphene-like materials have been employed as asphalt binder modifying agents in pavement engineering. In the literature, it has been reported that (in comparison to an unmodified binder) the Graphene Modified Asphalt Binders (GMABs) exhibit an enhanced performance grade, a lower thermal susceptibility, a higher fatigue life, and a decreased accumulation of permanent deformations. Nonetheless, although GMABs stand out significantly from traditional alternatives, there is still no consensus on their behavior regarding chemical, rheological, microstructural, morphological, thermogravimetric, and surface topography properties. Therefore, this research conducted a literature review on the properties and advanced characterization techniques of GMABs. Thus, the laboratory protocols covered by this manuscript are atomic force microscopy, differential scanning calorimetry, dynamic shear rheometer, elemental analysis, Fourier transform infrared spectroscopy, Raman spectroscopy, scanning electron microscopy, thermogravimetric analysis, X-ray diffraction, and X-ray photoelectron spectroscopy. Consequently, the main contribution of this investigation to the state-of-the-art is the identification of the prominent trends and gaps in the current state of knowledge.

Speciation of inorganic selenium in natural water by in situ solid-phase extraction using functionalized silica

Functionalized adsorbents with poly-(4,9-dioxododecane-1,12-guanidine) (SiO₂-PDDG) and mercaptophenyl groups (MPhS) were used for the separation of Se(VI) and Se(IV) for the first time. Fixation of PDDG was characterized by capillary electrophoresis and TGA/DSC. The quantitative extraction of Se(VI) proceeded due to anion exchange at pH 3-7. The adsorption capacity of SiO₂-PDDG for Se(VI) was 28 μmol g^-1. Silicas with mercaptophenyl groups were used for the extraction of Se(IV) from solutions in the range of 2 M HCl - pH 6.5. The adsorption capacity of MPhS was 35 μmol g^-1. A system of columns containing synthesized adsorbents was proposed for the separation of Se(VI) and Se(IV) and their subsequent determination by ICP-MS. Optimal parameters of adsorption include a flow rate of 1 mL min^-1, pH of 5, and sample volume of 200 mL. Se(IV) was desorbed with 5 mL of 0.25 M 2,3-dimercapto-1-propanesulphonic acid and Se(VI) with 5 mL of 1 M HNO₃. The preconcentration factor was 40. The limits of detection (3s) were 0.75 and 1.25 ng L^-1 for Se(VI) and Se(IV), respectively. The proposed method (SPE-ICPMS) was used to determine selenium species in natural water and certified reference materials. The separation was carried out directly at the sampling site.

Voltammetric and impedimetric determinations of selenium(iv) by an innovative gold-free poly(1-aminoanthraquinone)/multiwall carbon nanotube-modified carbon paste electrode

Selenite (Se4+), a significant source of water pollution above the permissible limits, is considered a valuable metal by environmentalists. In this study, we described a novel electrochemical sensor that utilized a carbon paste electrode (CPE) that was modified using multiwall carbon nanotubes (MWCNTs) and poly(1-aminoanthraquinone) (p-AAQ) for finding Se4+ in water samples. Electrochemical quantification of Se4+ depends on the formation of a selective complex (piaselenol) with p-AAQ. In this work, we prepared a CPE modified by physical embedding of MWCNTs and 1-aminoanthraquione (AAQ), while the polymer film was formed by anodic polymerization of AAQ by applying a constant potential of 0.75 V in 0.1 M HCl for 20 s followed by cyclic voltammetry (CV) from -0.2 to 1.4 V for 20 cycles. The modified CPE was used for differential pulse voltammetry (DPV) of Se4+ in 0.1 M H2SO4 from 0 to 0.4 V with a characteristic peak at 0.27 V. Further, the proposed sensor was characterized by scanning electron microscopy, energy-dispersive X-ray spectroscopy, and electrochemical impedance spectroscopy (EIS). The analytical conditions regarding the electrode performance and voltammetric measurements were optimized, with the accumulation time and potential, supporting electrolyte, differential-pulse period/time, and amplitude. The EIS results indicated that the p-AAQ/MWCNTs-modified CPE sensor (p-AAQ/MWCNTs/CPE) that also exhibited low charge-transfer resistance (R ct) toward the anodic stripping of Se4+, exhibited good analytical performance toward different concentrations of Se4+ in a linear range of 5-50 μg L-1 Se4+ with a limit of determination (LOD) of 1.5 μg L-1 (3σ). Furthermore, differential-pulse voltammetry was employed to determine different concentrations of Se4+ in a linear range of 1-50 μg L-1 Se4+, and an LOD value of 0.289 μg L-1 was obtained. The proposed sensor demonstrated good precision (relative standard deviation = 4.02%) at a Se4+ concentration of 5 μg L-1. Moreover, the proposed sensor was applied to analyze Se4+ in wastewater samples that were spiked with Se, and it achieved good recovery values.

Materials interacting with inorganic selenium from the perspective of electrochemical sensing

Inorganic selenium, the most common form of harmful selenium in the environment, can be determined using electrochemical sensors, which are compact, fast, reliable and easy-to-operate devices. Despite progress in this area, there is still significant room for developing high-performance selenium electrochemical sensors. To achieve this, one should take into account (i) the electrochemical process that selenium undergoes on the electrode; (ii) the valence state of selenium species in the sample and (iii) modification of the sensor surface by a material with high affinity to selenium. The goal of this review is to provide a knowledge base for these issues. After the Introduction section, mechanisms and principles of the electrochemical reduction of selenium are introduced, followed by a section introducing the modification of electrodes with materials interacting with selenium and a section dedicated to speciation methods, including the reduction of non-detectable Se(VI) to detectable Se(IV). In the following sections, the main types of materials (metallic, polymers, hybrid (nano)materials…) interacting with inorganic selenium (mostly absorbents) are reviewed to show the diversity of properties that may be endowed to sensors if the materials were to be used for the modification of electrodes. These features for the main material categories are outlined in the conclusion section, where it is stated that the engineered polymers may be the most promising modifiers.

Determination of selenite and selenomethionine in kefir grains by reversed-phase high-performance liquid chromatography-inductively coupled plasma-optical emission spectrometry

A new and efficient reversed-phase high-performance liquid chromatography-inductively coupled plasma-optical emission spectrometry method was developed for the simultaneous separation and determination of SeO₃ ^2- and seleno-dl-methionine in kefir grains. For the system, limits of detection and quantitation values for SeO₃ ^2- and seleno-dl-methionine were calculated as 0.52/1.73 mg/kg (as Se) and 0.26/0.87 mg/kg (as Se), respectively. After performing the system analytical performance, recovery experiment was done for kefir grains and percent recovery results for SeO₃ ^2- and seleno-dl-methionine were calculated as 98.4 ± 0.8% and 93.6 ± 1.0%, respectively. It followed by the feeding studies that the kefir grains were exposed to three different concentrations of SeO₃ ^2- (20, 30, and 50 mg/kg) for approximately 4 days at room temperature to investigate the conversion/non-conversion of SeO₃ ^2- to seleno-dl-methionine. Next, the fed grains were extracted with tetramethylammonium hydroxide pentahydrate solution (20%, w/w) and then sent to the developed system. There was no detectable seleno-dl-methionine found in fed kefir grains at different concentrations of SeO₃ ^2- while inorganic or elemental selenium in the fed kefir grains was determined between 1579.5 - 3116.0 mg/kg (as Se). Selenium species in the kefir grains samples was found in the form of SeO₃ ^2- proved by using an anion exchange column.

Discussions of Fluorescence in Selenium Chemistry: Recently Reported Probes, Particles, and a Clearer Biological Knowledge

In this review from literature appearing over about the past 5 years, we focus on selected selenide reports and related chemistry; we aimed for a digestible, relevant, review intended to be usefully interconnected within the realm of fluorescence and selenium chemistry. Tellurium is mentioned where relevant. Topics include selenium in physics and surfaces, nanoscience, sensing and fluorescence, quantum dots and nanoparticles, Au and oxide nanoparticles quantum dot based, coatings and catalyst poisons, thin film, and aspects of solar energy conversion. Chemosensing is covered, whether small molecule or nanoparticle based, relating to metal ion analytes, H2S, as well as analyte sulfane (biothiols-including glutathione). We cover recent reports of probing and fluorescence when they deal with redox biology aspects. Selenium in therapeutics, medicinal chemistry and skeleton cores is covered. Selenium serves as a constituent for some small molecule sensors and probes. Typically, the selenium is part of the reactive, or active site of the probe; in other cases, it is featured as the analyte, either as a reduced or oxidized form of selenium. Free radicals and ROS are also mentioned; aggregation strategies are treated in some places. Also, the relationship between reduced selenium and oxidized selenium is developed.

A miniaturized UV-LED array chip-based photochemical vapor generator coupled with a point discharge optical emission spectrometer for the determination of trace selenium

Ultraviolet light emitting diode array chip-based photochemical vapor generation was combined with hollow electrode point discharge to establish a miniaturized optical emission spectrometer for efficient vapor generation and excitation of selenium.

Zirconium nanoparticles based dispersive solid phase extraction prior to slotted quartz tube-flame atomic absorption spectrophotometry for the determination of selenium in green tea samples

In this study, a novel, easy, rapid and green zirconium nanoparticles (Zr-NPs) based dispersive solid phase extraction (DSPE) method is presented for the precise and sensitive determination of selenium by slotted quartz tube-flame atomic absorption spectrophotometry (SQT-FAAS). Influential parameters of the extraction procedure were optimized by altering one parameter while keeping the other parameters constant. The optimum conditions were selected as 10 mg of Zr-NPs, 75 s vortex period, and 200 µL of concentrated HCl for 30 mL of sample/standard solution. The linear range of the developed method was found to be between 25 and 100 µg/L, and the respective limits of detection and quantification were 5.3 and 18 µg/L. About 415 folds enhancement in detection power was achieved by the optimized method relative to the conventional FAAS. Green tea samples were spiked and used for recovery experiments and the results obtained were between 92 and 102%.

Performance of selenate removal by biochar embedded nano zero-valent iron and the biological toxicity to Escherichia coli

The application of nano zero-valent iron (nZVI) in water environment was limited by its easily aggregation and potential biological toxicity. In this study, biochar embedded nZVI (BC-nZVI) was prepared by carbon-thermal reduction method, and the SEM-EDX mapping results showed that nZVI was successfully embedded on biochar. Meanwhile, BC-nZVI with the optimal Fe/C of 2/1 showed a similar Se(vi) removal efficiency to pure nZVI. Effects of pH, BC-nZVI loading, and initial Se(vi) concentration were studied. Se(vi) removal rates (at 30 min) by BC-nZVI at pH 4.0 and 5.0 were 98.2% and 95.9%, respectively. But Se(vi) removal rate (at 30 min) was sharply decreased to 25.8% at pH 6.0. With the increase of BC-nZVI loading from 0.5 g L⁻¹ to 1 g L⁻¹, Se(vi) removal rate (at 30 min) significantly increased from 25.5% to 95.9%. And the continuous increase of BC-nZVI loading to 2 g L⁻¹ did not improve Se(vi) removal rate. Se(vi) less than 3 mg L⁻¹ was completely removed by BC-nZVI in 30 min, but Se(vi) more than 6 mg L⁻¹ only was removed about 25.9% at 30 min. Optimal parameters were pH 4.0, 2 g L⁻¹ BC-nZVI, and 1.5 mg L⁻¹ Se(vi). Variation of calculated amount, SOD activity, and protein content of Escherichia coli with nZVI and BC-nZVI indicated that nZVI and BC-nZVI both produced negative effects on the growth of E. coli. But the amount and SOD activity of E. coli with pure nZVI was lower than that with BC-nZVI. Moreover, E. coli with nZVI released more protein than that with BC-nZVI. So modified nZVI by biochar was less harmful to E. coli than nZVI.

The application of nano zero-valent iron (nZVI) in water environment was limited by its easily aggregation and potential biological toxicity.

Selenium Analysis and Speciation in Dietary Supplements Based on Next-Generation Selenium Ingredients

Selenium is essential for humans and the deficit of Se requires supplementation. In addition to traditional forms such as Se salts, amino acids, or selenium-enriched yeast supplements, next-generation selenium supplements, with lower risk for excess supplementation, are emerging. These are based on selenium forms with lower toxicity, higher bioavailability, and controlled release, such as zerovalent selenium nanoparticles (SeNPs) and selenized polysaccharides (SPs). This article aims to focus on the existing analytical systems for the next-generation Se dietary supplement, providing, at the same time, an overview of the analytical methods available for the traditional forms. The next-generation dietary supplements are evaluated in comparison with the conventional/traditional ones, as well as the analysis and speciation methods that are suitable to reveal which Se forms and species are present in a dietary supplement. Knowledge gaps and further research potential in this field are highlighted. The review indicates that the methods of analysis of next-generation selenium supplements should include a step related to chemical species separation. Such a step would allow a proper characterization of the selenium forms/species, including molecular mass/dimension, and substantiates the marketing claims related to the main advantages of these new selenium ingredients.

Application of novel nanocomposite-modified electrodes for identifying rice wines of different brands

In this paper, poly(acid chrome blue K) (PACBK)/AuNP/glassy carbon electrode (GCE), polysulfanilic acid (PABSA)/AuNP/GCE and polyglutamic acid (PGA)/CuNP/GCE were self-fabricated for the identification of rice wines of different brands. The physical and chemical characterization of the modified electrodes were obtained using scanning electron microscopy and cyclic voltammetry, respectively. The rice wine samples were detected by the modified electrodes based on multi-frequency large amplitude pulse voltammetry. Chronoamperometry was applied to record the response values, and the feature data correlating with wine brands were extracted from the original responses using the 'area method'. Principal component analysis, locality preserving projections and linear discriminant analysis were applied for the classification of different wines, and all three methods presented similarly good results. Extreme learning machine (ELM), the library for support vector machines (LIB-SVM) and the backpropagation neural network (BPNN) were applied for predicting wine brands, and BPNN worked best for prediction based on the testing dataset (R 2 = 0.9737 and MSE = 0.2673). The fabricated modified electrodes can therefore be applied to identify rice wines of different brands with pattern recognition methods, and the application also showed potential for the detection aspects of food quality analysis.

An electrochemical sequential injection method to investigate the adsorption of selenite on Fe(III) polyhydroxy cations intercalated vermiculite

A sequential injection - square wave anodic stripping voltammetry (SI-SWASV) method for determination of Se(IV) at a gold working electrode was developed to investigate the adsorption of Se(IV) onto vermiculite intercalated with Fe(III) polyhydroxy cations. The limits of detection and quantification were 0.060 and 0.20 μmol L^-1, respectively (4.7 and 15.7 μg L^-1). The linearity was up to 1.0 μmol L^-1, and the sampling throughput was 18 analyses h^-1. The proposed approach is a low-cost alternative to more expensive spectrometric methods. Adsorption onto vermiculite intercalated with Fe(III) polyhydroxy cations removed 93% of Se(IV) from a 1.0 μmol L^-1 solution (250 mL) after 5 min of contact time with 625 mg of adsorbent. Adsorption isotherms (25.0 ± 0.5 °C) were fitted by the Freundlich equation resulting in 1/n = 0.51 ± 0.03 and K_f = (1.584 ± 0.002) × 10³ μmol^1-1/n g^-1 L^1/n (r² = 0.995). Fitting by the Langmuir equation resulted in an adsorption constant of 0.026 ± 0.008 L g^-1 and adsorption capacity of 47 ± 5 μmol g^-1 (3.7 ± 0.4 mg g^-1) (r² = 0.97). This capacity was higher than that found for several other iron oxides, but lower than that obtained for oxide/hydroxide-based Fe(III) nanoparticles.