Environmental applications of solid-phase microextraction

Simultaneous and sensitive detection of methylparaben and its metabolites by using molecularly imprinted solid-phase microextraction fiber array technique

BACKGROUND

Methylparaben (MP), a commonly used antibacterial preservative, is widely used in personal care products, foods, and pharmaceuticals. MP and its metabolites are easy to enter the water environment, and their exposure and accumulation have negative effects on the ecological environment and human health, and have endocrine disrupting activity and potential physiological toxicity. It is still the primary issue of environmental analysis and ecological risk assessment to develop simple and reliable methods for simultaneous sensitive detection of these compounds in environmental water.

RESULTS

In this paper, a flexible molecularly imprinted fiber array strategy is proposed for simultaneous enrichment and detection of trace MP and its four main metabolites. The experimental results showed that the three-fiber imprinted fiber array constructed by MP imprinted fiber had the best effect on the simultaneous enrichment of these five target analytes. The enrichment capacity of the imprinted fiber array was 214-456 times, 314-1201 times and 38-685 times that of commercial PA, PDMS and PDMS/DVB fiber arrays, respectively. The limit of detection (LOD) of this method was 0.033 μg L-1. The spiked recovery rate was 86.78-113.96 %, and RSD was less than 9.17 %. In addition, this molecularly imprinted SPME fiber array has good stability, long service life and can be used repeatedly at least 100 times.

SIGNIFICANCE

This molecularly imprinted fiber array strategy can flexibly assemble different molecularly imprinted SPME fibers together, effectively improve the enrichment ability and detection sensitivity, and achieve simultaneous selective enrichment and detection of several analytes. This is an easy, efficient and reliable method for monitoring several trace analytes simultaneously in intricate environmental matrices.

Supramolecular Materials as Solid-Phase Microextraction Coatings in Environmental Analysis

Solid-phase microextraction (SPME) has been widely proposed for the extraction, clean-up, and preconcentration of analytes of environmental concern. Enrichment capabilities, preconcentration efficiency, sample throughput, and selectivity in extracting target compounds greatly depend on the materials used as SPME coatings. Supramolecular materials have emerged as promising porous coatings to be used for the extraction of target compounds due to their unique selectivity, three-dimensional framework, flexible design, and possibility to promote the interaction between the analytes and the coating by means of multiple oriented functional groups. The present review will cover the state of the art of the last 5 years related to SPME coatings based on metal organic frameworks (MOFs), covalent organic frameworks (COFs), and supramolecular macrocycles used for environmental applications.

Polycyclic aromatic hydrocarbon (PAH) accumulation in selected medicinal plants: a mini review

The use of plant-based products in healthcare systems has experienced a tremendous rise leading to a substantial increase in global demand. However, the quality and effectiveness of such plant-based treatments are often affected due to contamination of various pollutants including polycyclic aromatic hydrocarbons (PAHs). Like other plants, medicinal plants also uptake and accumulate PAHs when exposed to a contaminated environment. The consumption of such medicinal plants and/or plant-based products causes negative effects on health rather than providing any therapeutic advantages. Unfortunately, research focusing on PAH accumulation in medicinal plants has received very limited attention. This review discusses a sizable number of literature regarding the concentration of sixteen priority PAH pollutants as recognised by the US Environmental Protection Agency (USEPA) in different medicinal plants. The review also highlights the risk assessment of cancer associated with some medicinal plants in terms of benzo[a]pyrene (BaP) equivalent concentrations.

Polyaniline-coated kapok fibers for convenient in-syringe solid-phase microextraction and determination of organochlorine and pyrethroid pesticide residues in aqueous samples

Pesticides used in agriculture have low polarity and a tendency to accumulate in fatty tissues, posing potential risks to human health. Effective pre-treatment is crucial due to complex sample matrices and low concentrations of pesticide residues typically encountered in instrument analysis. In this study, polyaniline-coated kapok fiber (PANI-KF) was synthesized successfully using in-situ oxidative polymerization for use as sorbents in in-syringe SPME of pyrethroid pesticides (PYRs) and organochlorine pesticides (OCPs) from aqueous samples. Coating the natural KF with PANI maintained the hollow microtubular structure and fiber morphology while significantly enhancing the extraction efficiency. The extraction process was easily conducted by simply pulling and pushing the syringe plunger. The entire extraction process, utilizing 3 mg of PANI-KF, could be completed in approximately 3 min. Density functional theory results indicated that the adsorption mechanism of PANI-KF towards OCPs and PYRs mainly involved van der Waals interactions, π-π interactions, and weak hydrogen bonding interactions. With the coupling of gas chromatography-mass spectrometry, a quantification method was established that exhibited good linearities (R2 > 0.990), and relative recoveries (87.2-108.5 %). The limits of detection ranged from 0.4 to 2.0 ng mL-1 and the matrix effects were negligible (-12.3-16.4 %). The validated in-syringe SPME-GC-MS method was successfully applied to determine pesticide residues in fruit juices, oral liquids and herbal extract granules with satisfactory accuracy and precision. PANI-KF exhibits remarkable promise as a sorbent for the extraction and enrichment of pesticide residues in aqueous samples, thereby contributing to the advancement of pesticide residue determination methodologies.

Embedding Mixed Sorbents in Binder: Solid-Phase Microextraction Coating with Wide Extraction Coverage and Its Application in Environmental Water Analysis

Solid-phase microextraction (SPME) is a simple and highly effective sample-preparation technique for water analysis. However, the extraction coverage of a given SPME device with a specific coating can be an issue when analyzing multiple environmental contaminants. Therefore, instead of synthesizing one sorbent material with dual or multiple functions, we investigated a new strategy of preparing SPME blades using a homogeneous slurry made by mixing three different sorbent particles─namely, hydrophobic/lipophilic balanced (HLB), HLB-weak cationic exchange (HLB-WCX), and HLB-weak anionic exchange (HLB-WAX)─with a polyacrylonitrile (PAN) binder. The developed coating is matrix compatible, as the binder functions not only as a glue for immobilizing the sorbent particles but also as a porous filter, which only allows small molecules to enter the pores and interact with the particles, thus avoiding contamination from large elements. The results confirmed that the proposed mixed-coating SPME device provides good extraction performance for polar and nonpolar as well as positively and negatively charged compounds. Based on this device, three comprehensive analytical methodologies─high-throughput SPME-LC-MS/MS (for the quantitative analysis of targeted drugs of abuse and artificial sweeteners), in-bottle SPME-LC-high resolution MS (HRMS) (for the untargeted screening of organic contaminants), and on-site drone sampling SPME-LC-HRMS (for on-site sampling and untargeted screening)─were developed for use in environmental water analysis. The resultant data confirm that the proposed strategies enable comprehensive water quality assessment by using a single SPME device.

Current status and future challenges of chlorobenzenes pollution in soil and groundwater (CBsPSG) in the twenty-first century: a bibliometric analysis

The global industrial structure had undertaken significant changes since the twenty-first century, making a severe problem of chlorobenzene pollution in soil and groundwater (CBsPSG). CBsPSG receives increasing attention due to the high toxicity, persistence, and bioaccumulation of chlorobenzenes. To date, despite the gravity of this issue, no bibliometric analysis (BA) of CBsPSG does exist. This study fills up the gap by conducting a BA of 395 articles related to CBsPSG from the Web of Science Core Collection database using CiteSpace. Based on a comprehensive analysis of various aspects, including time-related, related disciplines, keywords, journal contribution, author productivity, and institute and country distribution, the status, development, and hotspots of research in the field were shown visually and statistically. Moreover, this study has also delved into the environmental behavior and remediation techniques of CBsPSG. In addition, four challenges (unequal research development, insufficient cooperation, deeply mechanism research, and developing new technologies) have been identified, and corresponding suggestions have been proposed for the future development of research in the field. Afterwards, the limitations of BA were discussed. This work provides a powerful insight into CBsPSG, enabling to quickly identify the hotspot and direction of future studies by relevant researchers.

Physisorption Behaviors of Organochlorine Pesticides on the InP3 Monolayer from Theoretical Insight

Dichlorodiphenyltrichloroethane (DDT), hexachlorocyclohexane (BHC), aldrin, and chlordimeform are ubiquitous organochlorine pesticide (OCP) residues in the environment, which pose a great threat to human health and ecosystems due to their high toxicity and easy accumulation. Based on the density functional theory (DFT) calculations, a two-dimensional InP3 monolayer was selected as a sensing material to study the sensitivity detection and adsorption behaviors toward BHC, aldrin, chlordimeform, and DDT. The calculation results show that four pesticide molecules are adsorbed on the InP3 surface by physical interaction. The identified response values (69.1, -43.1%) for DDT and chlordimeform reveal the potential of the InP3 monolayer as a sensing material for the detection of these two pesticides, accompanied by the achievement of cyclic utilization by heating to 498 K. The most satisfactory result is the adsorption of BHC, owing to the admirable sensing response (62.7%) and short recovery time (1.8 s) at room temperature, which makes InP3 a promising pesticide sensor for BHC. However, the InP3 surface is unsuitable for aldrin sensing due to poor response (-1.9%). Our work gives theoretical insight into the good sensitivity and recycling of the InP3 monolayer as a new pesticide sensor to detect DDT, BHC, and chlordimeform, which further broadens the application prospect of the InP3 nanosheet into the sensitive detection of organochlorine pesticides in the ecological environment.

Performance Evaluation of Extraction Coatings with Different Sorbent Particles and Binder Composition

Binders are critical components used in the preparation of a range of extraction devices, including solid-phase microextraction (SPME) devices. While the main role of a binder is to affix the sorbent particles to the selected support, it is critical to select the optimal binder to ensure that it does not negatively impact the coating's particle sorption capability. This work presents the first comprehensive investigation of the interactions between binders and solid sorbent particles as these interactions can significantly impact the performance of the coating. Specifically, the findings presented herein provide a better understanding of the extraction mechanisms of composite coatings and new rules for predicting the particle adhesion forces and binder distribution in the coating. The influence of binder chemistry on coating performance is investigated by examining a selection of the most used binders, namely, polydimethylsiloxane (PDMS), polyacrylonitrile (PAN), poly(vinylidene difluoride) (PVDF), polytetrafluoroethylene amorphous fluoroplastics (PTFE AF 2400), and polybenzimidazole (PBI). The solid particles (e.g., hydrophilic-lipophilic balanced (HLB) and C18) used in this work were selected for their ability to provide optimal extraction coverage for a broad range of analytes. The results show that PDMS does not change the properties of the solid particles and that the binder occupies a negligible volume due to shrinking after polymerization, resulting in the solid particles making up most of the coating volume. Hence, the coating sorption characteristics correspond closely to the properties of the selected solid particles. On the other hand, the results also showed that PTFE AF 2400 can interact with the active surface of the sorbent, leading to the deactivation of the sorbent particles. Therefore, the extraction performance and permeability coefficients decrease as the size of the penetrant increases, indicating a rigid porous structure. The results of this study can aid in the optimization of SPME devices as they provide reference values that can be used to determine the optimal binder and the sorbent affinity for the targeted compounds. Finally, the present work also provides the broader scientific community with a strategy for investigating the properties of sorbent particle/binder structures and defines the characteristics of a good coating/membrane by analyzing all parameters such as kinetics, thermodynamic equilibria, and morphology.

A robust and ultra-high-surface hydrogen-bonded organic framework promoting high-efficiency solid phase microextraction of multiple persistent organic pollutants from beverage and tea

Persistent organic pollutants (POPs) are widely distributed in the environment and are toxic, even at low concentrations. In this study, we first used hydrogen-bonded organic framework (HOF) to enrich POPs, based on solid phase microextraction (SPME). The HOF called PFC-1 (self-assembled by 1,3,6,8-tetra(4-carboxylphenyl)pyrene) has an ultra-high specific surface area, excellent thermochemical stability, and abundant functional groups, making it potential to be an excellent coating in SPME. And the as-prepared PFC-1 fiber have demonstrated outstanding enrichment abilities for nitroaromatic compounds (NACs) and POPs. Furthermore, the PFC-1 fiber was coupled with gas chromatography-mass spectrometry (GC-MS) to develop an ultrasensitive and practical analytical method with wide linearity (0.2-200 ng·L^-1), low detection limits for organochlorine pesticides (OCPs) (0.070-0.082 ng·L^-1) and polychlorinated biphenyls (PCBs) (0.030-0.084 ng·L^-1), good repeatability (6.7-9.9%), and satisfactory reproducibility (4.1-8.2%). Trace concentrations of OCPs and PCBs in drinking water, tea beverage, and tea were also determined precisely with the proposed analytical method.

Carbon nanotubes-assisted solid-phase microextraction for the extraction of gasoline in fire debris samples

Gasoline is one of the most encountered ignitable liquids (IL) in fire debris analysis. The extraction of gasoline from fire debris samples presents challenges due to the complicated nature of multicomponent mixtures. This research work proposed a novel carbon nanotube-assisted solid phase microextraction (CNT-SPME) fiber coupled with gas chromatography and mass spectrometry (GC/MS) to determine gasoline residues for fire debris analysis. The CNT-SPME fiber was prepared by a sequential coating of polydopamine, epoxy, and CNTs on a stainless-steel wire. The extraction capabilities of the CNT-SPME fiber for gasoline and its major aromatic groups (xylenes, alkylbenzenes, indanes, and naphthalenes) from neat and spiked samples were promising, with linear dynamic ranges of 0.4-12.5 and 3.1-12.5 µg 20-mL^-1 headspace vial, respectively. The average relative standard deviations and accuracies for all concentration ranges in this work were lower than 15%. The relative recovery of the CNT-SPME fiber for all aromatic groups ranged from 28 ± 3% to 59 ± 2%. Additionally, the CNT-SPME fiber showed a higher selectivity for the naphthalenes group in gasoline, as indicated by the experimental outcome using a pulsed thermal desorption process of the extracts. We envision the nanomaterial-based SPME offers promising opportunities for extracting and detecting other ILs to support fire investigation.

Cellulose Nanocrystals Induced Loose and Porous Graphite Phase Carbon Nitride/Porous Carbon Composites for Capturing and Determining of Organochlorine Pesticides from Water and Fruit Juice by Solid-Phase Microextraction

Herein, novel, loose, and porous graphite phase carbon nitride/porous carbon (g-C₃N₄@PC) composites were prepared by decorating cellulose nanocrystals (CNCs). The characterization results demonstrate that the as-prepared composites presented high specific surface areas, porous structures, and abundant chemical groups, with the modification of CNCs. In view of the unique advantages, g-C₃N₄@PC was used as the coating material for the solid-phase microextraction (SPME) of organochlorine pesticides (OCPs) in water and juice samples. The g-C₃N₄@PC-coated fibers showed better extraction efficiencies than commercial fibers (100/7 μm PDMS and PA) toward the OCPs, with the enrichment factors of the g-C₃N₄@PC-coated fibers 5-30 times higher than the latter. Using a gas chromatography-mass spectrometry (GC-MS) instrument, the g-C₃N₄@PC-coated fibers exhibited a gratifying analytical performance for determining low concentrations of OCPs, with a wide linear range (0.1-1600 ng L^-1 for water; 0.1-1000 ng L^-1 for juice), low limits of detection (0.0141-0.0942 ng L^-1 for water; 0.0245-0.0777 ng L^-1 for juice), and good reproducibility and repeatability in optimal conditions. The established method showed good sensitivity and recovery in the determination of OCPs in the water and fruit juice samples, which displayed broad prospects for analyzing organic pollutants from environmental samples.

Exploring different high-capacity tools and extraction modes to characterize the aroma of brewed coffee

In the present work, the potential benefit of using multi-cumulative trapping headspace extraction was explored by comparing the results using solid-phase microextraction (SPME) coated with divinylbenzene/carboxen/polydimethylsiloxane and a probe-like tool coated with polydimethylsiloxane. The efficiency of a single 30-min extraction, already explored in previous work, was compared with that of multiple shorter extractions. We evaluated three different conditions, i.e., three repeated extractions for 10 min each from different sample vials (for both the probe-like tool and SPME) or from the same vial (for SPME) containing brewed coffee. The entire study was performed using comprehensive two-dimensional gas chromatography coupled with mass spectrometry. The two-dimensional plots were aligned and integrated using a tile-sum approach before any statistical analysis. A detailed comparison of all the tested conditions was performed on a set of 25 targeted compounds. Although a single 30-min extraction using the probe-like tool provided a significantly higher compound intensity than SPME single extraction, the use of multiple shorter extractions with SPME showed similar results. However, multiple extractions with the probe-like tool showed a greater increase in the number of extracted compounds. Furthermore, an untargeted cross-sample comparison was performed to evaluate the ability of the two tested tools and the different extraction procedures in differentiating between espresso-brewed coffee samples obtained from capsules made of different packaging materials (i.e., compostable capsules, aluminum capsules, aluminum multilayer pack). The highest explained variance was obtained using the probe-like tool and multiple extractions (91.6% compared to 83.9% of the single extraction); nevertheless, SPME multiple extractions showed similar results with 88.3% of variance explained.

N, N'-methylene bisacrylamide/divinyl benzene based-highly cross-linked hybrid monolithic column: Production and its applications for powerful capture of four chlorophenols

In this paper, the role of the halogen bond in capillary monolithic column microextraction was explored for the first time. Benzene-1,3,5-tricarbohydrazide (BTH) was synthesized as a functional monomer, N, N'-methylene bisacrylamide (MBA) and divinyl benzene (DVB) were used as cross-linking agents, the hybrid monolithic column of poly (BTH-co-DVB-co-MBA) was prepared using methanol and polyethylene glycol as pore-forming agents and azodiisobutyronitrile as the initiator. Due to the existence of BTH, a large number of nitrogen atoms (Lewis base) were introduced into the monolithic column, which could form a halogen bond with chlorine-containing organic pollutants and enhance its adsorption performance. Based on the monolithic column, a sensitive and environment-friendly solid-phase microextraction technology was studied. The monolithic column was integrated with high-performance liquid chromatography (HPLC) to extract and detect four kinds of chlorophenol in real water samples. Under best conditions, the method showed excellent extraction ability and linearity, with a linear correlation coefficient of 0.9958-0.9987, a low detection limit (LOD) of 0.04-0.23 μg L^-1 (S/N = 3), and relative standard deviation (RSD) less than 3.09%. The recovery rate was kept between 87.30% and 123.00%, and the RSD was less than 3.83%, which indicated that the column had powerful capture performance, high precision, and strong anti-matrix interference ability in the real sample, and had potential application value in practical work.

Temporal chemical composition changes in water below a crude oil slick irradiated with natural sunlight

Photooxidation can alter the environmental fate and effects of spilled oil. To better understand this process, oil slicks were generated on seawater mesocosms and exposed to sunlight for 8 days. The molecular composition of seawater under irradiated and non-irradiated oil slicks was characterized using ion mobility spectrometry-mass spectrometry and polyaromatic hydrocarbons analyses. Biomimetic extraction was performed to quantify neutral and ionized constituents. Results show that seawater underneath irradiated oil showed significantly higher amounts of hydrocarbons with oxygen- and sulfur-containing by-products peaking by day 4-6; however, concentrations of dissolved organic carbon were similar. Biomimetic extraction indicated toxic units in irradiated mesocosms increased, mainly due to ionized components, but remained <1, suggesting limited potential for ecotoxicity. Because the experimental design mimicked important aspects of natural conditions (freshly collected seawater, natural sunlight, and relevant oil thickness and concentrations), this study improves our understanding of the effects of photooxidation during a marine oil spill.

Research Advances in the Analysis of Estrogenic Endocrine Disrupting Compounds in Milk and Dairy Products

Milk and dairy products are sources of exposure to estrogenic endocrine disrupting compounds (e-EDCs). Estrogenic disruptors can accumulate in organisms through the food chain and may negatively affect ecosystems and organisms even at low concentrations. Therefore, the analysis of e-EDCs in dairy products is of practical significance. Continuous efforts have been made to establish effective methods to detect e-EDCs, using convenient sample pretreatments and simple steps. This review aims to summarize the recently reported pretreatment methods for estrogenic disruptors, such as solid-phase extraction (SPE) and liquid phase microextraction (LPME), determination methods including gas chromatography-mass spectrometry (GC-MS), liquid chromatography-mass spectrometry (LC-MS), Raman spectroscopy, and biosensors, to provide a reliable theoretical basis and operational method for e-EDC analysis in the future.

Quantification of trace transformation products of rocket fuel unsymmetrical dimethylhydrazine in sand using vacuum-assisted headspace solid-phase microextraction

Quantification of unsymmetrical dimethylhydrazine transformation products in solid samples is an important stage in monitoring of environmental pollution caused by heavy rockets launches. The new method for simultaneous quantification of unsymmetrical dimethylhydrazine transformation products in sand samples using vacuum-assisted headspace solid-phase microextraction without addition of water followed by gas chromatography-mass spectrometry is proposed. Decreasing air evacuation time from 120 to 20 s at 23 °C resulted in increased responses of analytes by 25-46% and allowed obtaining similar responses as after evacuation at -30 °C. The best combination of responses of analytes and their relative standard deviations (RSDs) was achieved after air evacuation of a sample (m = 1.00 g) for 20 s at 23 °C, incubation for 30 min at 40 °C, and 30-min extraction at 40 °C by Carboxen/polydimethylsiloxane (Car/PDMS) fiber. The method was validated in terms of linearity (R²=0.9912-0.9938), limits of detection (0.035 to 3.6 ng g^-1), limits of quantification (0.12-12 ng g^-1), recovery (84-97% with RSDs 1-11%), repeatability (RSDs 3-9%), and reproducibility (RSDs 7-11%). It has a number of major advantages over existing methods based on headspace solid-phase microextraction-lower detection limits, better accuracy and precision at similar or lower cost of sample preparation. The developed method was successfully applied for studying losses of analytes from open vials with model sand spiked with unsymmetrical dimethylhydrazine transformation products. It can be recommended for analysis of trace concentrations of unsymmetrical dimethylhydrazine transformation products when studying their transformation, migration and distribution in contaminated sand.

In Vivo Solid-Phase Microextraction and Applications in Environmental Sciences

Solid-phase microextraction (SPME) is a well-established sample-preparation technique for environmental studies. The application of SPME has extended from the headspace extraction of volatile compounds to the capture of active components in living organisms via the direct immersion of SPME probes into the tissue (in vivo SPME). The development of biocompatible coatings and the availability of different calibration approaches enable the in vivo sampling of exogenous and endogenous compounds from the living plants and animals without the need for tissue collection. In addition, new geometries such as thin-film coatings, needle-trap devices, recession needles, coated tips, and blades have increased the sensitivity and robustness of in vivo sampling. In this paper, we detail the fundamentals of in vivo SPME, including the various extraction modes, coating geometries, calibration methods, and data analysis methods that are commonly employed. We also discuss recent applications of in vivo SPME in environmental studies and in the analysis of pollutants in plant and animal tissues, as well as in human saliva, breath, and skin analysis. As we show, in vivo SPME has tremendous potential for the targeted and untargeted screening of small molecules in living organisms for environmental monitoring applications.

Portable stirring device for the on-site extraction of environmental waters using magnetic hydrophilic-lipophilic balance tape

The spatial heterogeneity of environmental systems makes sampling at multiple locations crucial to provide complete and representative information. The on-site application of an extraction technique simplifies the sampling logistics, increasing sample integrity during transportation and storage. This article presents a portable, simple, and low-cost device capable of performing the simultaneous on-site extraction of several environmental water samples. The device consists of a small electric motor integrated into the plastic cap of a conventional glass bottle and operated with a portable battery. The electric motor provides stirring to a novel magnetic sorptive phase based on the deposition of hydrophilic-lipophilic balance (HLB) particles over a magnetic tape. The use of open technology makes the device globally affordable. In this first approach, the isolation and preconcentration of atrazine and simazine have been selected as proof of concept. Using an internal standard made unnecessary the adjustment of the ionic strength before the extraction, thus simplifying the analytical procedure. Under the optimum conditions and using direct infusion mass spectrometry as the instrumental technique, detection limits as low as 15 ng/L were obtained. The precision calculated at three different levels was better than 8.3%. The accuracy, calculated with spiked samples, indicates the applicability of the approach for environmental water analysis.

Controllable in situ growth of novel octahedral TiO2 nanoparticles on nickel/titanium alloy fiber substrate for selective solid-phase microextraction of ultraviolet filters in water samples

The nature and fabrication of fiber coatings with good adsorption capacity and selectivity play a decisive role in solid-phase microextraction (SPME). In this work, a novel SPME fiber was fabricated through hydrothermal in situ growth of octahedral TiO₂ nanoparticles (TiO₂NPs) on a superelastic nickel/titanium alloy (NiTi) wire substrate in acid solution. The resulting fiber coatings were characterized by scanning electron microscopy and energy dispersive X-ray spectroscopy. Acid types, acid concentration as well as hydrothermal temperature and time were found to be effective route to manipulate the morphologies and composition of TiO₂-based nanoflakes grown on the NiTi fiber substrates. At the concentration of 0.4 mol L⁻¹ HCl as well as hydrothermal temperature of 150 °C and hydrothermal time of 12 h, TiO₂NPs were in situ grown on the NiTi wire substrates. The obtained NiTi wire with the TiO₂NPs coating (NiTi@TiO₂NPs fiber) was employed to investigate the adsorption of some representative aromatic analytes in water samples coupling with high-performance liquid chromatography with UV detection (HPLC/UV). The results clearly demonstrate that the fiber exhibits good extraction selectivity for ultraviolet filters (UVFs). In view of good extraction selectivity for the selected UVFs, the key experimental parameters were optimized. Under the optimum conditions, the calibration curves were linear in the ranges of 0.05–100 μg L⁻¹ with the correlation coefficients greater than 0.998. Limits of detection (LODs) were 0.007 to 0.064 μg L⁻¹. Furthermore, the intra-day and inter-day repeatability of the proposed method with the single fiber varied from 4.3% to 6.1% and from 4.5% to 6.8%, respectively. The fiber-to-fiber reproducibility ranged from 5.8% to 8.2%. The developed SPME-HPLC/UV method was applied to selective preconcentration and sensitive determination of target UVFs from real water samples. Moreover, the fabricated fiber showed precisely controllable growth and 150 extraction and desorption cycles.

This work presents a facile strategy with in situ growth of TiO₂ nanoparticles on nickel/titanium alloy wire through hydrothermal method for selective preconcentration and determination of UVFs in water.

Study of an adsorption method for trace mercury based on Bacillus subtilis

In order to decrease the difficulty in trace mercury determination, an adsorption method for trace mercury based on Bacillus subtilis cells was proposed in this article. The adsorption process was characterized by optical microscopy and SEM. The adsorption mechanism was analyzed by IR. The adsorption performance was studied by measuring the concentration of supernate and calculating the adsorption efficiency. When adsorbing Hg2+, Bacillus subtilis cells gathered and their structure turned coarse. The IR results illustrated that functional groups bound with Hg for complexation during adsorption. Bacillus subtilis completed adsorption for trace Hg2+ in 15 min. The adsorption efficiency was maintained above 80% under low Hg2+ concentrations (<200 µg/L). The proposed study illustrates that Bacillus subtilis cells are highly efficient and easily obtained material for the adsorption of trace mercury, which shows potential to be further used in the pretreatment of trace Hg2+ detection.

Novel solid-phase microextraction fiber coatings: A review

The materials used for the fabrication of solid-phase microextraction fiber coatings in the past five years are summarized in the current review, including carbon, metal-organic frameworks, covalent organic frameworks, aerogel, polymer, ionic liquids/poly (ionic liquids), metal oxides, and natural materials. The preparation approaches of different coatings, such as sol-gel technique, in-situ growth, electrodeposition, and glue methods, are briefly reviewed together with the evolution of the supporting substrates. In addition, the limitations of the current coatings and the future development directions of solid-phase microextraction are presented.

Current overview and perspectives in environmentally friendly microextractions of carbamates and dithiocarbamates

Carbamates and dithiocarbamates are two classes of pesticides widely employed in the agriculture practice to control and avoid pests and weeds, hence, the monitoring of the residue of those pesticides in different foodstuff samples is important. Thus, this review presents the classification, chemical structure, use, and toxicology of them. Moreover, it was shown the evolution of liquid- and solid-phase microextractions employed in the extraction of carbamates and dithiocarbamates in water and foodstuff samples. The classification, operation mode, and application of the microextractions of liquid-phase and solid-phase used in their extraction were discussed and related to the analytical parameters and guidelines of green analytical chemistry.

Recent Advances in Sample Preparation for Cosmetics and Personal Care Products Analysis

The use of cosmetics and personal care products is increasing worldwide. Their high matrix complexity, together with the wide range of products currently marketed under different forms imply a challenge for their analysis, most of them requiring a sample pre-treatment step before analysis. Classical sample preparation methodologies involve large amounts of organic solvents as well as multiple steps resulting in large time consumption. Therefore, in recent years, the trends have been moved towards the development of simple, sustainable, and environmentally friendly methodologies in two ways: (i) the miniaturization of conventional procedures allowing a reduction in the consumption of solvents and reagents; and (ii) the development and application of sorbent- and liquid-based microextraction technologies to obtain a high analyte enrichment, avoiding or significantly reducing the use of organic solvents. This review provides an overview of analytical methodology during the last ten years, placing special emphasis on sample preparation to analyse cosmetics and personal care products. The use of liquid–liquid and solid–liquid extraction (LLE, SLE), ultrasound-assisted extraction (UAE), solid-phase extraction (SPE), pressurized liquid extraction (PLE), matrix solid-phase extraction (MSPD), and liquid- and sorbent-based microextraction techniques will be reviewed. The most recent advances and future trends including the development of new materials and green solvents will be also addressed.

Temperature and time-controlled hydrothermal growth and sorption selectivity of titania nanowires on titanium fiber for highly efficient solid-phase microextraction

Two kinds of TiO₂ nanowires (TiO₂NWs) with different orientation were in-situ grown on Ti substrates by controlling temperature and time during the hydrothermal process. The adsorption performance was evaluated by using typical aromatic compounds as model analytes coupled to HPLC with UV detection. The results demonstrated that the TiO₂NWs coating grown at higher temperature within longer time had better affinity towards PAHs. For this purpose, the key experimental factors affecting the adsorption performance of the TiO₂NWs coating fabricated at 200 °C for 10 h were further investigated and optimized for the extraction of PAHs. Under the optimized conditions, the proposed method presented linear responses in the concentration ranges of 0.05 to 200 μg·L^-1 PAHs with correlation coefficients more than 0.998. LODs (S/N=3) were 0.008 to 0.034 μg·L^-1. Moreover, RSDs for the single fiber repeatability of the intra-day and the inter-day analyses were less than 5.6% (n=5) and 5.8%, respectively. RSDs for the fiber-to-fiber reproducibility were between 5.1% and 6.5%. Finally, the proposed method was successfully applied to the selective preconcentration and determination of trace PAHs in environmental water samples. In addition, The fabricated Ti fiber can be used at least 200 times due to its high mechanical and chemical stability.

Surface nanodroplet-based nanoextraction from sub-milliliter volumes of dense suspensions

A greener analytical technique for quantifying compounds in dense suspensions is needed for wastewater and environmental analysis, chemical or bio-conversion process monitoring, biomedical diagnostics, and food quality control, among others. In this work, we introduce a green, fast, one-step method called nanoextraction for extraction and detection of target analytes from sub-milliliter dense suspensions using surface nanodroplets without toxic solvents and pre-removal of the solid contents. With nanoextraction, we achieve a limit of detection (LOD) of 10-9 M for a fluorescent model analyte obtained from a particle suspension sample. The LOD is lower than that in water without particles (10-8 M), potentially due to the interaction of particles and the analyte. The high particle concentration in the suspension sample, thus, does not reduce the extraction efficiency, although the extraction process was slowed down up to 5 min. As a proof of principle, we demonstrate the nanoextraction for the quantification of model compounds in wastewater slurry containing 30 wt% solids and oily components (i.e. heavy oils). The nanoextraction and detection technology developed in this work may be used in fast analytical technologies for complex slurry samples in the environment, industrial waste, or in biomedical diagnostics.

Sheathed in-situ room-temperature growth covalent organic framework solid-phase microextraction fiber for detecting ultratrace polybrominated diphenyl ethers from environmental samples

The extraction performance of solid-phase microextraction (SPME) fiber is significantly influenced by coating materials and fabricating process. It is urgently needed for fabricating robust SPME fiber with facile preparation methods. Herein, a novel polyimide (PI) @ covalent organic framework (COF) synthesized by 1,3,5-Tris (4-aminophenyl) benzene (TPB) and 2,5-dimethoxyterephthalaldehyde (DMTP) fiber, named PI@TPB-DMTP fiber, was successfully fabricated with facile method at room temperature. Firstly, a COF crystals TPB-DMTP was in situ grown on stainless steel fiber, where the COF crystals was synthesized by the Schiff-base reaction between TPB and DMTP. Subsequently, the COF coating was covered with an ultrathin layer of PI through a simple dip-coating method to improve the fiber stability. By coupled PI@TPB-DMTP SPME fiber with gas chromatography-negative chemical ion-mass spectrometry (GC-NCI-MS), a sensitive analytical method was established for the determination of ultratrace polybrominated diphenyl ethers (PBDEs) in water sample. To achieve the best efficiency and sensitivity for the analysis of PBDEs, six potential influencing factors in extraction step and desorption step were optimized. Under optimized conditions, the established method showed high enhancement factors of 1470-3555, wide linear range of 0.05-100 ng L^-1, low detection limits of 0.0083-0.0190 ng L^-1, good repeatability for intra-day in the range of 3.71%-7.62% and inter-day in the range of 5.12%-8.81%, good reproducibility in the range of 6.83%-9.21%. The satisfactory recovery was ranged from 79.2% to 117.3% in determining real water samples. The excellent experimental performance was mainly attributed to the large specific surface area of TPB-DMTP, as well as the high permeability of porous PI film. The results demonstrated that the COF-based fiber showed great potential for analysis of PBDEs in complex environmental samples.

Task specific monolith for magnetic field-reinforced in-tube solid phase microextraction of mercury species in waters prior to online HPLC quantification

In this study, a novel sorbent based on task specific monolith doped with Fe₃O₄ was in situ fabricated in capillary and acted as the extraction medium of magnetic field-reinforced in-tube solid phase microextraction (MFR/IT-SPME) to trap and preconcentrate mercury species which were coordinated with dithizone to form chelates. Various characterization technologies evidenced that the obtained monolithic adsorbent presented porous and super paramagnetic properties, and possessed abundant functional groups. Results evidenced that the implementation of magnetic field during extraction stages enhanced the extraction efficiency of studied Hg chelates from 48.5% to 75.3% to 69.9-94.4%. Under the optimized extraction parameters, the introduced MFR/IT-SPME was online coupled to HPLC/DAD to quantify mercury species at ultra-trace levels in various water samples. Limits of detection varied from 0.0067 μg/L to 0.016 μg/L, and the RSDs for precision were below 7.5%. Additionally, related extraction mechanism was deduced and revealed multiple forces co-contributed to the enrichment. The reliability and accuracy of suggested online approach for speciation analysis of mercury was well proved by confirmatory experiments.

Fan-based device for integrated air sampling and microextraction

In this article, a new air sampler based on a conventional computer fan is presented and evaluated. The fan has a double role as it acts as the air pumping system and supports the sorptive phases, which are located on its blades. The compact design and the reduced energy consumption (it can operate with a standard cell phone charger) confers high portability to the device. Also, a simple alternative integrated into the fan is proposed for using an internal standard during the sampling, thus increasing the precision of the measurements. In this first communication, sol-gel Carbowax 20 M coated fabric phases are used as sorptive membranes thanks to their planar geometry, mechanical and thermal stability, and their versatility covering different interaction chemistries. After sampling, the fabric phases are placed in a headspace vial, which is finally analyzed by gas chromatography-mass spectrometry. The sampler has been characterized for the extraction of selected volatile organic compounds (chloroform, benzaldehyde, toluene, and cyclohexane) from air and its versatility has also been evaluated by the identification of semi-volatile compounds in working place (toluene and xylene in laboratory residue storage room) and biogenic volatile compounds in natural samples (terpenes in fresh pine needles and orange peel samples).

Electro-enhanced solid-phase microextraction with covalent organic framework modified stainless steel fiber for efficient adsorption of bisphenol A

In this work, electro-enhanced solid-phase microextraction (EE-SPME) and covalent organic framework (COF) were adopted to improve the extraction efficiency. A conductive COF synthesized of 2,6-diaminoanthraquinone (DQ) and 1,3,5-triformylphloroglucinol (TP) was in situ bonded to the stainless steel wire via facile solution-phase approach and used as the EE-SPME fiber coating to preconcentrate a typical endocrine disruptor bisphenol A (BPA). Compared with conventional SPME, the DQTP bonded fiber coupled with EE-SPME device exhibited higher extraction efficiency and achieved extraction equilibrium within 10 min. The proposed approach based on EE-SPME and gas chromatography coupled with flame ionization detector gave a linear range of 0.05-10 μg mL^-1 and detection limit of 3 μg L^-1 (S/N = 3) with good precision (<6.7%) and reproducibility (<7.1%) spiked with 0.1, 0.5, 1.0 μg mL^-1 BPA. Quantitative determination of BPA in extracts of food packagings (mineral water bottles, milk boxes and milk tea cups) was achieved with recoveries from 88.6 to 118.0%.

Facile fabrication and application of poly(ortho-phenetidine) nanocomposite coating for solid-phase microextraction of carcinogenic polycyclic aromatic hydrocarbons from wastewaters

The waters and wastewaters around industrial areas are heavily polluted and have adverse effects on the ecosystems. The present study is mainly focused on the electropolymerization of ortho-phenetidine and co-deposited on a steel wire along with graphene oxide nanosheets as a novel coating for solid-phase microextraction of polycyclic aromatic hydrocarbons (PAHs) from aqueous media prior to gas chromatography-mass spectrometry. PAHs are composed of multiple aromatic rings which have been linked to skin, lung, bladder and liver. Cancer is a primary human health risk of exposure to PAHs. To obtain a firm and stable coating, several empirical factors relevant to the electrochemical process were investigated. Characterization for chemical structure and surface morphology of the synthesized nanocomposite was conducted with FT-IR spectroscopy and FE-SEM, respectively. XRD and TGA were applied to study the other properties of the nanocomposite. Some essential items involved in microextraction process were also checked in details. Under optimized case, validation parameters were assessed. Wide linearity (0.005-5.0 ng mL^-1), low detection limits (0.4-4.3 pg mL^-1) and good repeatability (3.6-9.5%) and reproducibility (7.6-11.8%) were achieved. The developed method was utilized to analyze contaminated real samples such as wastewater samples from coal processing industries and agricultural water samples collected from the vicinity of the industry in different seasons and high recoveries were obtained, finally.

In-tube solid-phase microextraction: Current trends and future perspectives

In-tube solid-phase microextraction (IT-SPME) was developed about 24 years ago as an effective sample preparation technique using an open tubular capillary column as an extraction device. IT-SPME is useful for micro-concentration, automated sample cleanup, and rapid online analysis, and can be used to determine the analytes in complex matrices simple sample processing methods such as direct sample injection or filtration. IT-SPME is usually performed in combination with high-performance liquid chromatography using an online column switching technology, in which the entire process from sample preparation to separation to data analysis is automated using the autosampler. Furthermore, IT-SPME minimizes the use of harmful organic solvents and is simple and labor-saving, making it a sustainable and environmentally friendly green analytical technique. Various operating systems and new sorbent materials have been developed to improve its extraction efficiency by, for example, enhancing its sorption capacity and selectivity. In addition, IT-SPME methods have been widely applied in environmental analysis, food analysis and bioanalysis. This review describes the present state of IT-SPME technology and summarizes its current trends and future perspectives, including method development and strategies to improve extraction efficiency.

Miniaturized analytical methods for determination of environmental contaminants of emerging concern - A review

The determination of contaminants of emerging concern (CECs) in environmental samples has become a challenging and critical issue. The present work focuses on miniaturized analytical strategies reported in the literature for the determination of CECs. The first part of the review provides brief overview of CECs whose monitoring in environmental samples is of particular significance, namely personal care products, pharmaceuticals, endocrine disruptors, UV-filters, newly registered pesticides, illicit drugs, disinfection by-products, surfactants, high technology rare earth elements, and engineered nanomaterials. Besides, an overview of downsized sample preparation approaches reported in the literature for the determination of CECs in environmental samples is provided. Particularly, analytical methodologies involving microextraction approaches used for the enrichment of CECs are discussed. Both solid phase- and liquid phase-based microextraction techniques are highlighted devoting special attention to recently reported approaches. Special emphasis is placed on newly developed materials used for extraction purposes in microextraction techniques. In addition, recent contributions involving miniaturized analytical flow techniques for the determination of CECs are discussed. Besides, the strengths, weaknesses, opportunities and threats of point of need and portable devices have been identified and critically compared with chromatographic methods coupled to mass chromatography. Finally, challenging aspects regarding miniaturized analytical methods for determination of CECs are critically discussed.

Sheathed in situ heteroepitaxial growth metal-organic framework probe for detection of polycyclic aromatic hydrocarbons in river water and living fish

Exploring the presence of polycyclic aromatic hydrocarbons (PAHs) in aquatic environment is an important task. Metal-organic frameworks (MOF) are commonly used as sorbents for enriching PAHs but their crystal synthesis, sorbent preparation and robustness remain challenging. In the present study, under mild conditions, a novel sheathed MOF fiber coating was fabricated via in situ heteroepitaxial growth of copper-2,5-diaminoterephthalate (Cu-DAT) crystals and subsequent polyimide (PI) sheath. The copper hydroxide nanotubes were first synthesized on the copper wire to provide a substrate for further in situ heteroepitaxial Cu-DAT growth, and the coating was then sheathed with PI via a simple dip-coating procedure. The well-ranged copper hydroxide nanotubes, the unique adsorption property of Cu-DAT, and the PI sheath, the prepared fiber all contributed to a successful solid-phase microextraction (SPME) device for detecting PAHs. Results demonstrated that the SPME methods using the novel fiber possessed great sensitivity, wide linear range, good reproducibility, and the robustness was significantly improved with PI sheath. The novel SPME material was successfully applied for detection of PAHs in river water samples and in vivo detection of PAHs in fish dorsal muscle. In general, this study explored an effective and convenient method to prepare high-efficient MOF-based SPME fiber for PAHs analysis in complex environmental water samples and living organisms via in situ growth and polymer sheath.