The effect of preparation time and aeration rate on the properties of bulk micro-nanobubble water using hydrodynamic cavitation

Ultrasound Pretreatment for Enhancing Fine and Ultrafine Flake Graphite Flotation Beneficiation

With the severe depletion of coarse flake graphite (a critical raw material) resources, developing and utilizing fine and ultrafine graphite resources have recently attracted attention. Froth flotation is a widely used technique for the initial enrichment of graphite; however, the flotation selectivity decreases significantly along with particle size reduction. Ultrasound pretreatment would be a promising method to improve the flotation of fine particles. As an innovative approach to understand better the flotation response of different flake graphite sizes, this study conducted a comparative analysis based on flotation concentrate yield and ash as well as ash removal rate between the flake graphite with various particle sizes after ultrasound pretreatment. Particle size, X-ray powder diffraction, and scanning electron microscopy and energy dispersive X-ray spectroscopy analyses were used to investigate the effect of ultrasound treatment on mineralogical properties of the flake graphite with varied particle sizes. Process outcomes indicated that the flotation performance of fine flake graphite (mean chord length: 62.63 μm) was significantly enhanced after ultrasound pretreatment. However, flotation of the ultrafine flake graphite (mean chord length: 24.97 μm) after ultrasound treatment was limited due to the difficulty of generating sufficient fragmentation and dissociation by microjets and shock waves formed by the cavitation effect. Compared with conventional flotation, the concentrate yield of ultrasound flotation increased from 88.95 to 94.98%, ash content decreased from 5.72 to 4.87%, and ash removal rate enhanced from 36.94 to 42.61%. Particle size and mineral property analyses confirmed that further crushing and dissociation of the larger flake graphite after ultrasound pretreatment would be the main factors contributing to improved flotation performance. Additionally, the formation of air flocs in the coarse flake graphite during the ultrasound pretreatment process facilitated the flotation recovery of the crushed graphite particles.

Mechanism of the Decrease in Surface Tension by Bulk Nanobubbles (Ultrafine Bubbles)

The mechanism of the decrease in the surface tension of water containing bulk nanobubbles (ultrafine bubbles) is studied theoretically by numerical simulations of the adsorption of bulk nanobubbles at the liquid's surface based on the dynamic equilibrium model for the stability of a bulk nanobubble under the conditions of the Tuziuti experiment (Tuziuti, T., et al., Langmuir, 2023, 39, 5771-5778). It is predicted that the concentration of bulk nanobubbles in the bulk liquid decreases considerably with time, as many bulk nanobubbles are gradually adsorbed at the liquid's surface. A part of the decrease in surface tension is due to the Janus-like structure of a bulk nanobubble that could partly break the hydrogen bond network of water molecules at the liquid's surface because more than 50% of the bubble's surface is covered with hydrophobic impurities, according to the dynamic equilibrium model. The theoretically estimated decrease in surface tension due to the Janus-like structure of a bulk nanobubble agrees with the experimental data of the decrease in surface tension solely by bulk nanobubbles obtained by the comparison of before and after the elimination of bulk nanobubbles by the freeze-thaw process. This effect cannot be explained by the electric charge stabilization model widely discussed for the stability of a bulk nanobubble, although the present model is only applicable to the solution containing hydrophobic impurities. Another part of the decrease in surface tension should be due to impurities produced from a nanobubble generator, such as a mechanical seal, which was partly confirmed by the TOC measurements.

Current decontamination challenges and potentially complementary solutions to safeguard the vulnerable seafood industry from recalcitrant human norovirus in live shellfish: Quo Vadis?

Safeguarding the seafood industry is important given its contribution to supporting our growing global population. However, shellfish are filter feeders that bioaccumulate microbial contaminants in their tissue from wastewater discharged into the same coastal growing environments leading to significant human disease outbreaks unless appropriately mitigated. Removal or inactivation of enteric viruses is very challenging particularly as human norovirus (hNoV) binds to specific histo-blood ligands in live oyster tissue that are consumed raw or lightly cooked. The regulatory framework that sets out use of clean seawater and UV disinfection is appropriate for bacterial decontamination at the post-harvest land-based depuration (cleaning) stage. However, additional non-thermal technologies are required to eliminate hNoV in live shellfish (particularly oysters) where published genomic studies report that low-pressure UV has limited effectiveness in inactivating hNoV. The use of the standard genomic detection method (ISO 15, 216-1:2017) is not appropriate for assessing the loss of infectious hNoV in treated live shellfish. The use of surrogate viral infectivity methods appear to offer some insight into the loss of hNoV infectiousness in live shellfish during decontamination. This paper reviews the use of existing and potentially other combinational treatment approaches to enhance the removal or inactivation of enteric viruses in live shellfish. The use of alternative and complementary novel diagnostic approaches to discern viable hNoV are discussed. The effectiveness and virological safety of new affordable hNoV intervention(s) require testing and validating at commercial shellfish production in conjunction with laboratory-based research. Appropriate risk management planning should encompass key stakeholders including local government and the wastewater industry. Gaining a mechanistic understanding of the relationship between hNoV response at molecular and structural levels in individually treated oysters as a unit will inform predictive modeling and appropriate treatment technologies. Global warming of coastal growing environments may introduce additional contaminant challenges (such as invasive species); thus, underscoring need to develop real-time ecosystem monitoring of growing environments to alert shellfish producers to appropriately mitigate these threats.

Effect of ultrasound power on HCl leaching kinetics of impurity removal of aphanitic graphite

This study aimed to investigate the effect of ultrasonic power and temperature on the impurity removal rate during conventional and ultrasonic-assisted leaching of aphanitic graphite. The results showed that the ash removal rate increased gradually (∼50 %) with the increase in ultrasonic power and temperature but deteriorated at high power and temperature. The unreacted shrinkage core model was found to fit the experimental results better than other models. The Arrhenius equation was used to calculate the finger front factor and activation energy under different ultrasonic power conditions. The ultrasonic leaching process was significantly influenced by temperature, and the enhancement of the leaching reaction rate constant by ultrasound was mainly reflected in the increase of the pre-exponential factor A. Ultrasound treatment improved the efficiency of impurity mineral removal by destroying the inert layer formed on the graphite surface, promoting particle fragmentation, and generating oxidation radicals. The poor reactivity of hydrochloric acid with quartz and some silicate minerals is a bottleneck limiting the further improvement of impurity removal efficiency in ultrasound-assisted aphanitic graphite. Finally, the study suggests that introducing fluoride salts may be a promising method for deep impurity removal in the ultrasound-assisted hydrochloric acid leaching process of aphanitic graphite.

Decrease in the Surface Tension of Nanobubble Dispersion in Water: Results of Surface Excess of Bulk Nanobubbles at Interfaces

The effect of nanobubbles (NBs) on the surface tension of liquid was investigated by three methods of different measuring principles, pendant drop (PD), Wilhelmy, and du Noüy methods, over a wide range of number concentration of bulk NBs (BNBs). In all of the three methods, the surface tension decreased in proportion to the number concentration of BNBs and the proportional constant was different among the three methods. Such behavior was inferred to be caused by the surface excess of BNBs at the gas-liquid or solid-liquid interface. In the PD method, the hydrophobic interaction between BNBs and air around a drop seems to cause the surface excess of BNBs along the surface of water drops. It brings about a subtle change in its profile, resulting in the decrease in surface tension, which takes a time of hundreds of seconds. Meanwhile, in the Wilhelmy and du Noüy methods, electrostatic attractive force between BNBs and a plate or ring is a likely cause of surface excess at the solid-liquid interface, resulting in the instantaneous decrease in surface tension. This study also provides a practical methodology of comparison for surface tension of NB dispersion: surface tension shall be compared among different samples with the same measurement method. Especially in the PD method, retention time of droplets before measurement shall be the same among samples.

Critical Roles of Impurities and Imperfections in Various Phases of Materials

In many materials, impurities and imperfections play a critical role on the physical and chemical properties. In the present review, some examples of such materials are discussed. A bulk nanobubble (an ultrafine bubble) is stabilized against dissolution by hydrophobic impurities attached to the bubble surface. An acoustic cavitation threshold in various liquids decreases significantly by the presence of impurities such as solid particles, etc. The strength of brittle ceramics is determined by the size and number of pre-existing microcracks (imperfections) in the specimen. The size effect of a BaTiO3 nanocrystal is influenced by the amount and species of adsorbates (impurities) on its surface as adsorbate-induced charge-screening changes the free energy. The dielectric constant of an assembly of BaTiO3 nanocubes is influenced by a small tilt angle (imperfection) between two attached nanocubes, which induces strain inside a nanocube, and is also influenced by the spatial strain-relaxation due to defects and dislocations (imperfections), resulting in flexoelectric polarization.

Physicochemical Characteristics and the Scale Inhibition Effect of Air Nanobubbles (A-NBs) in a Circulating Cooling Water System

Air nanobubbles (A-NBs) in a circulating cooling water system have not been investigated, although their role is significant. In this paper, the influences of the contents of main salts and other parameters on the physicochemical characteristics and scale inhibition performance of A-NBs in circulating cooling water were investigated and the scale inhibition mechanism of A-NBs in a simulated circulating cooling water system was explored. A-NBs realized a higher scale inhibition rate of 90%, which was higher than that of 1-hydroxyethane-1,1-diphosphonic acid (40%), and A-NBs stably existed for more than 5 days in the complex water environment. Four interface functions were proposed to interpret the scale inhibition effect of A-NBs in circulating cooling water as follows. First, the negatively charged surface of A-NBs adsorbed cations (Ca²⁺) reduced the concentration of scaling ions. Second, the negatively charged surface of A-NBs could also adsorb microcrystals, and their crystal-like seed action was conducive to the formation of large-size crystals, broke the rules of crystal growth, and reduced the adhesion of scales to the pipe wall. Third, A-NBs could also form a bubble layer after they were adsorbed on the inner surface of pipes, thereby preventing the deposition of scales on the surface. Fourth, A-NB burst caused local turbulence, increased the shear force onto the pipe surface, and reduced the scales adhering to the pipe surface. The interface effect of A-NBs in metal pipes is important in many industrial applications. This study laid the basis for the development of a new green A-NB scale-inhibiting technology.

An Assessment of the Role of Combined Bulk Micro- and Nano-Bubbles in Quartz Flotation

Bulk micro-nano-bubbles (BMNBs) have been proven to be effective at improving the flotation recovery and kinetics of fine-grained minerals. However, there is currently no research reported on the correlation between the properties of BMNBs and flotation performance. For this purpose, aqueous dispersions with diverse properties were created by altering preparation time (0, 1, 2, 3, 5, and 7 min), aeration rate (0, 0.5, 1, 1.5, and 2 L/min) and aging time (0, 0.5, 1, and >3 min). Micro- and nano-bubbles were characterized using focused beam reflection measurements (FBRM) and nanoparticle tracking analysis (NTA), respectively. The micro-flotation of quartz particles was performed using an XFG-cell in the presence and absence of BMNBs with Cetyltrimethylammonium bromide (CTAB) as a collector. The characterization of bubble sizes showed that the bulk micro-bubble (BMB) and bulk nanobubble (BNB) diameters ranged from 1–10 μm and 50–400 nm, respectively. It was found that the preparation parameters and aging time considerably affected the number of generated bubbles. When BNBs and BMBs coexisted, the recovery of fine quartz particles significantly improved (about 7%), while in the presence of only BNBs the promotion of flotation recovery was not significant (2%). This was mainly related to the aggregate via bridging, which was an advantage for quartz flotation. In comparison, no aggregates were detected when only nano-bubbles were present in the bulk solution.

On Some Aspects of Nanobubble-Containing Systems

Theoretical studies are reviewed for bulk nanobubbles (ultrafine bubbles (UFBs)), which are gas bubbles smaller than 1 μm in diameter. The dynamic equilibrium model is discussed as a promising model for the stability of a UFB against dissolution; more than half of the surface of a UFB should be covered with hydrophobic material (impurity). OH radicals are produced during hydrodynamic or acoustic cavitation to produce UFBs. After stopping cavitation, OH radicals are generated through chemical reactions of H2O2 and O3 in the liquid water. The possibility of radical generation during the bubble dissolution is also discussed based on numerical simulations. UFBs are concentrated on the liquid surface according to the dynamic equilibrium model. As a result, rupture of liquid film is accelerated by the presence of UFBs, which results in a reduction in "surface tension", measured by the du Noüy ring method. Finally, the interaction of UFBs with a solid surface is discussed.