Using sodium percarbonate to suppress vertically distributed filamentous cyanobacteria while maintaining the stability of microeukaryotic communities in drinking water reservoirs

Emergency control of dinoflagellate bloom in freshwater with chlorine enhanced by solar radiation: Efficiency and mechanism

Dinoflagellate requires a lower temperature and blooms frequently in the spring and autumn compared to regular cyanobacteria. The outbreak of dinoflagellate bloom will also lead to the death of some aquatic organisms. However, research on freshwater dinoflagellates is still lacking due to the challenges posed by classification and culture in laboratory. The removal effect and mechanism of Peridinium umbonatum (P. umbonatum, a typical dinoflagellate) were investigated using solar/chlorine in this study. The effect of simulated solar alone on the removal of algae was negligible, and chlorine alone had only a slight effect in removing algae. However, solar/chlorine showed a better removal efficiency with shoulder length reduction factor and kmax enhancement factor of 2.80 and 3.8, respectively, indicating a shorter latency period and faster inactivation rate for solar/chlorine compared to solar and chlorine alone. The removal efficiency of algae gradually increased with the chlorine dosage, but it dropped as the cell density grew. When the experimental temperature was raised to 30 °C, algal removal efficiency significantly increased, as the temperature was unsuitable for the survival of P. umbonatum. Attacks on cell membranes by chlorine and hydroxyl radicals (•OH) produced by solar/chlorine led to a decrease in cell membrane integrity, leading to a rise in intracellular reactive oxygen species and an inhibition of photosynthetic and antioxidant systems. Cell regeneration was not observed in either the chlorine or solar/chlorine systems due to severe cell damage or cysts formation. In addition, natural solar radiation was demonstrated to have the same enhancing effect as simulated solar radiation. However, the algal removal efficiency of solar/chlorine in real water was reduced compared to 119 medium, mainly due to background material in the real water substrate that consumed the oxidant or acted as shading agents.

Molecular mechanisms underlying sodium percarbonate treatment suppress the recovery and growth of Pseudanabaena sp. in early spring

Increasing frequency and intensity of cyanobacterial blooms in water sources is a growing global issue. Algicides are usually implemented in summer or autumn when blooms break out, however, the blooms will form again when algicide's concentration declines to a certain extent. Preventing the recovery and growth of cyanobacteria in early spring may be conducive to abatement of the blooms in summer or autumn. In this study solid sodium percarbonate (SPC) was used as an algicide to suppress recovery and growth of Pseudanabaena sp., a common odour-producing cyanobacterium, in early spring (12 °C). Results showed that 3.0 and 6.0 mg/L SPC were able to kill most of the algal cells after 12 h treatment at 12 °C, and the residual cells gradually died during the re-cultivation period at 25 °C. As a control, although SPC also caused most of algal cells to lyse at 25 °C, regrowth of cells was found during the period of re-cultivation at 25 °C. Transcriptomic analysis revealed that the dysregulated genes were strongly associated with translation and photosynthesis after SPC treatment. All differentially expressed unigenes related to translation and photosynthesis were down-regulated after SPC oxidation at 12 °C, whereas key genes associated with translation and photosynthesis were upregulated after SPC treatment at 25 °C.

Advances and challenges in the technologies for cyanobacterial cells removal in drinking water treatment

Harmful cyanobacteria in reservoirs pose a serious threat to drinking water safety due to the intracellular metabolites, such as toxins and unpleasant tastes & odours. Effective removal of harmful cyanobacteria with little to no cell damage is very important to ensure the safety of drinking water. This review first introduced development history of cyanobacterial removal technologies in drinking water treatment. Then, impacts of oxidation, coagulation and pre-oxidation enhanced coagulation processes on cyanobacterial removal and integrity of the cells were comprehensively evaluated and discussed. Oxidation can remove cyanobacteria, but high doses of oxidants can result in significant cell lysis and release of intracellular metabolites, especially when using chlorine or ozone. Although there is practically no cell damage during coagulation, the removal efficiency is low in many cases. Pre-oxidation may improve cyanobacterial removal by the subsequent solid-liquid separation processes, and moderate pre-oxidation with little to no cell lysis is very important. Mechanisms of interface interaction between pre-oxidants and cyanobacteria should be defined in future to ensure moderate pre-oxidation of algal cells. Fate of cyanobacterial cells in sludge is also reviewed because more and more waterworks return sludge supernatant to the inlet of plant. Damage to cyanobacterial cells in sludge depends mainly upon coagulant type and dosage, algal species, and cyanobacteria-containing sludge should be treated before cell lysis. Efficient techniques for harmless disposal of cyanobacteria-containing sludge should be developed in future. This paper will help to better understand the cyanobacterial removal processes and provide improved perspectives for future research in this field.

Effects of microcystin-LR on purification efficiency of simulating drinking water source by Hydrocharis dubia (Bl.) backer

The safety of drinking water source directly affects human health. Microcystin-LR (MC-LR), a toxic and common pollutant in drinking water source, is released by algae and can impede the in-situ remediation effect of aquatic plant. Finding out the effect mechanism of MC-LR on the purification of drinking water by aquatic plant is the key to its application. This study aims to explore the performance and mechanism of MC-LR on drinking water source purification by Hydrocharis dubia (Bl.) backer. The optimum removal efficiency of NH4+-N, TP and COD were 90.7%, 93.2% and 77.3% at MC-LR concentration of 0.5 μg L-1, respectively. With the increase of MC-LR concentration, the pollutants removal rate was obviously inhibited causing by concentration-dependent. Furthermore, the growth and development of the Hydrocharis dubia (Bl.) backer roots were significantly promoted at the concentration of 0.1 μg L-1. The length, tips, surface area, and average diameter of the root increased by 71.3%, 271.4%, 265.5%, and 113.0%, respectively. Chlorophyll contents under low-concentration MC-LR show a 14.5%-15.7% promoting effect compared with the control group. The activities of POD and CAT were also stimulated with the MC-LR increasing (<1.0 μg L-1). Notably, the MDA contents increased with increasing MC-LR concentration (p < 0.01). This study indicates the effect mechanism of MC-LR on Hydrocharis dubia (Bl.) backer purification performance relies on the increased growth and enzyme activity of Hydrocharis dubia (Bl.) backer.

Triclocarban transformation and removal in sludge conditioning using chalcopyrite-triggered percarbonate treatment

Herein, a facile combination approach of chalcopyrite and sodium percarbonate (CuFeS2+ SPC) was established to augment both TCC removal efficiency and sludge dewatering. Results showed that utilizing the CuFeS2 dosage of 600 mg/g total solids (TS) under the optimal condition, along with the SPC dosage of 12.5 mg/g TS, an initial pH of 4.0, and a reaction duration of 40 min, led to a substantial reduction of 53.9% in the TCC content within the sludge, accompanied by a notable decrease of 36.9% in the water content. Compared to well-studied iron-based advanced oxidation processes, CuFeS2 + SPC treatment proved to be more cost-effective and environmentally friendly. Mechanistic findings demonstrated that •OH oxidation played a significant role in TCC removal, with O2•- and 1O2 acting as secondary factors. During the CuFeS2 + SPC process, the received •OH, O2•-, and 1O2 destroyed the main binding sites of extracellular polymeric substances to TCC, including tryptophan-like protein, amide, CO stretch, and -COO- functional groups. As a result, approximately 50% of TCC was partially degraded within the solid sludge phase after the attack of radicals. Meanwhile, the decreased macromolecular organic compounds in solid sludge attenuated the binding efficacy of TCC, giving rise to the transfer of partial TCC to the liquid phase. Ultimately, the TCC in sludge was successfully removed, and five transformation products were identified. This study significantly contributes to our understanding regarding TCC transformation and removal in the sludge conditioning process.

The apoptosis of Chlorella vulgaris and the release of intracellular organic matter under metalimnetic oxygen minimum conditions

Metalimnetic oxygen minimum (MOM) is a frequent occurrence in lakes and reservoirs, and its formation is related to the blooming and apoptosis of algae. In this study, the apoptosis mechanism of Chlorella vulgaris (C. vulgaris) and the release of intracellular organic matter (IOM) under different MOM conditions were analyzed by changing the dissolved oxygen (DO) (7.0 mg/L, 3.0 mg/L, and 0.3 mg/L) and water pressure (0.3 MPa and normal pressure). The integrity and auto-fluorescence of algae cells decreased rapidly in the first 8 days, and then stabilized gradually during the development of MOM. Compared with that of water pressures, DO had a significant effect on the activity of algal cells, and higher initial DO levels (3.0 mg/L and 7.0 mg/L) accelerated the lysis of algal cells. The integrity of algae cells decreased to 28.8 %, 31.8 % and 56.6 % at the initial DO of 7 mg/L, 3 mg/L and 0.3 mg/L under 0.3 MPa, respectively. Meanwhile, the concentration of dissolved organic carbon (DOC) and dissolved organic nitrogen (DON) continued to increase and reached their maximum at 8 or 12 days, respectively, due to the IOM release caused by algal cell rupture, and then gradually decreased due to microbial degradation. Consistent with the results of membrane integrity, the highest DOC and DON concentrations were found at higher initial DO conditions. By parallel factor analysis, the change in total organic matter fluorescence intensity was consistent with DOC, once again increasing in the first 8 days and then gradually decreasing. The increased humic-like component, which is related to higher aromaticity, led to the monotonic increase of HAAFPs and THMFPs. However, the released IOM of C. vulgaris had lower N-DBPFPs, with TCNMFP predominating primarily. In summary, these results shed new lights on exploring the apoptosis of algae and the release of IOM during the development of MOM.

Temporal patterns of algae in different urban lakes and their correlations with environmental variables in Xi'an, China

Urban lakes were critical in aquatic ecology environments, but how environmental factors affected the distribution and change characteristics of algal communities in urban lakes of Xi'an city was not clearly. Here, we investigated the algal community structure of six urban lakes in Xi'an and evaluated the effects of water quality parameters on algae. The results indicated that the significant differences on physicochemical parameters existed in different urban lakes. The maximum concentration of total phosphorus in urban lakes was (0.18 ± 0.01) mg/L and there was a phenomenon of phosphorus limitation. In addition, 51 genera of algae were identified and Chlorella sp. was the dominant algal species, which was affiliated with Chlorophyta. Network analysis elucidated that each lake had a unique algal community network and the positive correlation was dominant in the interaction between algae species, illustrating that mature microbial communities existed or occupied similar niches. Redundancy analysis illustrated that environmental factors explained 47.35% variance of algal species-water quality correlation collectively, indicating that water quality conditions had a significant influence on the temporal variations of algae. Structural equation model further verified that algal community structure was directly or indirectly regulated by different water quality conditions. Our study shows that temporal patterns of algal communities can reveal the dynamics and interactions of different urban ecosystem types, providing a theoretical basis for assessing eutrophication levels and for water quality management.

A novel actinomycete Streptomyces enissocaesilis exhibiting algicidal activity against the toxic cyanobacterium Phormidium angustissimum

Harmful cyanobacterial blooms that occur in freshwater can produce hazardous cyanotoxins as contaminants that threaten ecosystems, aquatic organisms, and human health. In the present study, the actinobacterium Streptomyces enissocaesilis, strain M35, isolated from soils, exhibited the strongest algicidal activity against the toxic cyanobacterium Phormidium angustissimum TISTR 8247. To improve the P. angustissimum removal efficiency of strain M35, the optimum carbon and nitrogen sources were determined as starch and yeast extract, respectively. Response surface methodology (RSM) using the Box-Behnken design (BBD) revealed that the optimal independent parameters among the culture medium conditions for enhancing the algicidal activity of strain M35 were 21.5 g/L starch, 0.57 g/L yeast extract, and a pH value of 8.00. The Phormidium sp. removal efficiency increased notably from 80.8 to 94.4% under the optimum conditions. In a batch experiment, the removal of P. angustissimum in an internal airlift loop (IAL) bioreactor containing immobilized strain M35 on a plastic medium indicated a high anti-Phormidium activity of 94.8%, whereas in a continuous system, strain M35 exhibited a removal efficiency of 85.5%. This study revealed that this actinobacterium could potentially be utilized to remove the toxic cyanobacterium Phormidium from water.

Inactivation of Microcystis aeruginosa by H2O2 generated from a carbon black polytetrafluoroethylene gas diffusion electrode in electrolysis by low-amperage electric current

Frequent outbreaks of cyanobacterial blooms have seriously threatened aquatic ecological environments and human health. Electrolysis by low-amperage electric current is effective for algae inactivation; however, it has no selectivity. Hydrogen peroxide (H₂O₂) is considered to be an efficient and selective suppressor of algae. Therefore, it is necessary to develop an electrode that can generate H₂O₂ to improve electrolysis technology. In this study, a carbon black polytetrafluoroethylene gas diffusion electrode (C-PTFE GDE) with good stability was prepared by a simple adhesive coating method. Then, the inactivation of Microcystis aeruginosa was conducted with electrolysis by low-amperage electric current using Ti/RuO₂ as the anode and C-PTFE GDE as the cathode. When the electrode spacing was 4 cm, the current density was 20 mA cm^-2, and the gas flow was 0.4 L min^-1, 85% of the algae could be inactivated in 20 min. Comparing the inactivation effect of the electric field and electrogenerated oxidants, it was found that electrolysis more rapidly and strongly inactivated algae when an electric field existed. However, electrogenerated oxidants dominated algae inactivation. The concentration of H₂O₂ was as high as 58 mg L^-1, while the concentration of chlorines was only 0.57 mg L^-1, and the generation rate of H₂O₂ was 65 times that of chlorines. Consequently, electrogenerated oxidants dominated by H₂O₂ attacked photosystem II of the algae and caused oxidative damage to membrane lipids, affecting the photosynthetic capacity. Eventually, most of the algae were inactivated. The study suggested that C-PTFE GDE was promising for the inactivation of Microcystis aeruginosa in this electrochemical system.

Targeted Decomplexation of Metal Complexes for Efficient Metal Recovery by Ozone/Percarbonate

Traditional methods cannot efficiently recover Cu from Cu(II)-EDTA wastewater and encounter the formation of secondary contaminants. In this study, an ozone/percarbonate (O₃/SPC) process was proposed to efficiently decomplex Cu(II)-EDTA and simultaneously recover Cu. The results demonstrate that the O₃/SPC process achieves 100% recovery of Cu with the corresponding k_obs value of 0.103 min^-1 compared with the typical ^•OH-based O₃/H₂O₂ process (81.2%, 0.042 min^-1). The carbonate radical anion (CO₃^•-) is generated from the O₃/SPC process and carries out the targeted attack of amino groups of Cu(II)-EDTA for decarboxylation and deamination processes, resulting in successive cleavage of Cu-O and Cu-N bonds. In comparison, the ^•OH-based O₃/H₂O₂ process is predominantly responsible for the breakage of Cu-O bonds via decarboxylation and formic acid removal. Moreover, the released Cu(II) can be transformed into stable copper precipitates by employing an endogenous precipitant (CO₃^2-), accompanied by toxic-free byproducts in the O₃/SPC process. More importantly, the O₃/SPC process exhibits excellent metal recovery in the treatment of real copper electroplating wastewater and other metal-EDTA complexes. This study provides a promising technology and opens a new avenue for the efficient decomplexation of metal-organic complexes with simultaneous recovery of valuable metal resources.

Effects of copper sulfate algaecide on the cell growth, physiological characteristics, the metabolic activity of Microcystis aeruginosa and raw water application

Harmful cyanobacteria blooms (HCBs) occurred frequently and become a serious scientific challenge. Copper sulfate (CuSO₄) is a broad-spectrum chemical algaecide to control algae blooms. Herein, the Microcystis aeruginosa was exposed to different CuSO₄ (0.0, 0.2 and 0.5 mg/L) to assess the variations in algal physiological process and metabolic profiles. The results indicated that exposure to CuSO₄ of 0.5 mg/L at 72 h could significantly inhibit the cell growth and photosynthetic capacity of M. aeruginosa, including chl-a content and chlorophyll fluorescence parameters. Plasma membrane damage causing cell lysis of M. aeruginosa increased the K⁺ release. The increase of SOD and CAT suggested that CuSO₄ treatment caused oxidative stress in algal cells. Different doses of CuSO₄ modified the carbon metabolic potential, algal cells had their unique metabolic mode thereby. Moreover, the research further verified that CuSO₄ would also inhibit algal growth and change algal community structure in site-collected water application. Overall, laboratory results of M. aeruginosa to CuSO₄ and site-collected water application of algal responses to CuSO₄ might be conducive to uncovering the controlling mechanism of algae and the potential effect of carbon cycling in an ecological environment.

Advanced oxidation processes for water purification using percarbonate: Insights into oxidation mechanisms, challenges, and enhancing strategies

Percarbonate (SPC) has drawn considerable attention due to its merits in the safety of handling and transport, stability, and price as well as environmental friendliness, which has been extensively applied in advanced oxidation processes (AOPs) for water decontamination. Nevertheless, comprehensive information on the application of SPC-AOPs for the treatment of organic compounds in aquatic media is scarce. Hence, the focus of this review is to shed light on the mechanisms of reactive oxygen species (ROS) evolution in typical SPC-AOPs (i.e., Fenton-like oxidation, photo-assisted oxidation, and discharge plasma-involved oxidation processes). These SPC-AOPs enable the formation of multiple reactive species like hydroxyl radical (^•OH), superoxide radical (O₂^•-), singlet oxygen (¹O₂), carbonate radicals (CO₃^•-), and peroxymonocarbonate (HCO₄^-), which together or solely contribute to the degradation of target pollutants. Simultaneously, the potential challenges in practical applications of SPC-AOPs are systematically discussed, which include the influence of water quality parameters, cost-effectiveness, available active sites, feasible activation approaches, and ecotoxicity. Subsequently, enhancing strategies to improve the feasibility of SPC-AOPs in the practical implementation are tentatively proposed, which can be achieved by introducing reducing and chelating agents, developing novel activation approaches, designing multiple integrated oxidation processes, as well as alleviating the toxicity after SPC-AOPs treatment. Accordingly, future perspectives and research gaps in SPC-AOPs are elucidated. This review will hopefully offer valuable viewpoints and promote the future development of SPC-AOPs for actual water purification.

Biocides with Controlled Degradation for Environmentally Friendly and Cost-Effective Fecal Sludge Management

Didecyldimethylammonium chloride (DDAC) and polyhexamethylene guanidine (PHMG) exhibit high antimicrobial activity and are widely used as biocidal agents in chemical toilet additives for the management of fecal sludge (FS). Disposal of such biocide-treated FS to a wastewater treatment plant (WWTP) is a major environmental problem. It is possible to reduce environmental damage through the use of biocidal agents, which easily decompose after performing their main biocidal functions. In this work, it is proposed to use the fact of a gradual increase in pH of FS from the initial 7.5 to 9.0-10.0 due to the decomposition of urea. Six biocidal compounds were selected that are capable of rapidly degrading in an alkaline environment and one that naturally degrades upon prolonged incubation. Four of them: bronopol (30 mg/L), DBNPA (500 mg/L), Sharomix (500 mg/L), and sodium percarbonate (6000 mg/L) have shown promise for environmentally friendly management of FS. In selected dosage, they successfully reduced microbial activity under both aerobic and anaerobic conditions and are cost-effective. After 10 days of incubation, degradation of the biocide occurred as measured by biological oxygen demand (BOD₅) in biocide-treated FS. Such FS can be discharged to WWTP without severe damage to the activated sludge process, the need for dilution and additional procedures to neutralize toxicity.

Differentiation of DNA or membrane damage of the cells in disinfection by flow cytometry

Recently, the viabilities changes of fungal spores in the water supply system during different disinfection processes have been revealed. SYBR Green I (SG), a nucleic acid stain, its fluorescence intensity is correlated with the amount of double-stranded DNA. This study established a new method through successive SG-SG-PI staining (PI: Propidium Iodide) with flow cytometry (FCM). It could successfully distinguish DNA damage and membrane damage of fungal spores, clearly elucidating the intrinsic disinfection mechanism during the chemical disinfection. This method was briefly described as follows: firstly, (1) the fungal spores were stained with SG and washed by centrifugation; and then, (2) the washed spores were treated with disinfectants and terminated; after that, (3) the disinfected spores were re-stained with SG and analyzed by FCM; finally, (4) the SG re-stained spores were stained with PI and analyzed by FCM. The percentages of spores with DNA damage and membrane damage were determined by the fluorescence intensity obtained from steps (3) and (4), respectively. The repeatability and applicability of this developed method were confirmed. It was further applied to explore the inactivation mechanism during chlorine-based disinfection, and results demonstrated that chloramine attacked the DNA more seriously than the membrane, while chlorine and chlorine dioxide worked in a reverse way.

Moderate pre-ozonation coupled with a post-peroxone process remove filamentous cyanobacteria and 2-MIB efficiently: From bench to pilot-scale study

The increasing frequency and intensity of taste- and odour-producing cyanobacteria in water sources is a growing global issue. Odour events caused by 2-methylisoborneol (2-MIB) mainly arising from filamentous cyanobacteria have been a very common problem in water supply. Removal rates of filamentous cyanobacteria and 2-MIB by conventional water treatment, such as coagulation, and disinfection treatment processes is low. Hence, a moderate pre-ozonation of cyanobacteria (with little cell damage) was proposed in this study as an enhanced coagulation step to remove filamentous cyanobacteria and intracellular 2-MIB effectively, while avoiding the release of intracellular 2-MIB. A post-peroxone (O₃/H₂O₂) process was applied after sand filtration to degrade the residual dissolved 2-MIB. Results show that moderate pre-ozonation (0.2 mg/L O₃ oxidation for 20 min) can substantially enhance the coagulation efficiency for algae, with low cell lysis and high cell viability. Furthermore, 2.0 mg/L O₃ combined with 2.0 mg/L H₂O₂ can degrade the residual dissolved 2-MIB nearly 100% after 20 min reaction. Based on the optimal dosages, a 0.6 m³/h pilot system, including pre-ozonation, coagulation and sedimentation, sand filtration, and post-peroxone processes, was continuously run for 14 days, and it was found that the proposed process can effectively and stably remove filamentous cyanobacteria and 2-MIB.

Coupling sodium percarbonate (SPC) oxidation and coagulation for membrane fouling mitigation in algae-laden water treatment

To alleviate algal fouling in membrane water treatment processes, conventional technologies such as coagulation with poly aluminum chloride (PACl) has been widely adopted by many drinking water treatment plants. However, coagulation alone exhibited relatively weak removal effect for algal pollutants, and the coagulant residues due to the excess dosage also raised concerns. Thus, a novel process of coupling sodium percarbonate (SPC) oxidation and PACl coagulation was proposed, integrated with membrane filtration for algae-laden water treatment. The dosages of PACl and SPC were optimized, and the SPC dosing strategies were systematically compared. The changes in the characteristics of algal pollutants were investigated, and the results revealed that the resistance of algal foulants to aggregation was decreased, and the particle size of algal foulants became larger. With the synergism of coagulation and oxidation, the degradation of fluorescent organics was strengthened, and macromolecular biopolymers were decomposed into low molecular weight organics. The fouling control efficiency was further explored, and the results indicated that both irreversible and reversible fouling were effectively controlled, among which PACl/SPC (simultaneous treatment) performed best with the irreversible fouling reduced by 90.5%, while the efficiency of SPC-PACl (SPC followed by PACl) was relatively lower (57.3%). The fouling mechanism was altered by slowing the formation of cake filtration, and the reduction of algal cells played a more important role for the fouling alleviation. The interface properties of contaminated membranes (i.e., functional groups, images, and micromorphology) were characterized, and the efficiency of the proposed strategy was further verified. The proposed strategy exhibits great application values for improving membrane performance during algae-laden water treatment.

Cyanobacterial Harmful Algal Blooms in Aquatic Ecosystems: A Comprehensive Outlook on Current and Emerging Mitigation and Control Approaches

An intensification of toxic cyanobacteria blooms has occurred over the last three decades, severely affecting coastal and lake water quality in many parts of the world. Extensive research is being conducted in an attempt to gain a better understanding of the driving forces that alter the ecological balance in water bodies and of the biological role of the secondary metabolites, toxins included, produced by the cyanobacteria. In the long-term, such knowledge may help to develop the needed procedures to restore the phytoplankton community to the pre-toxic blooms era. In the short-term, the mission of the scientific community is to develop novel approaches to mitigate the blooms and thereby restore the ability of affected communities to enjoy coastal and lake waters. Here, we critically review some of the recently proposed, currently leading, and potentially emerging mitigation approaches in-lake novel methodologies and applications relevant to drinking-water treatment.