Gradients in immobilized biological systems

EPS-Then and Now

“Slime” played a brief and spectacular role in the 19th century founded by the theory of primordial slime by Ernst Haeckel. However, that substance was never found and eventually abandoned. Further scientific attention slowly began in the 1930s referring to slime as a microbial product and then was inspired by “How bacteria stick” by Costerton et al. in 1978, and the matrix material was considered to be polysaccharides. Later, it turned out that proteins, nucleic acids and lipids were major other constituents of the extracellular polymeric substances (EPS), an acronym which was highly discussed. The role of the EPS matrix turns out to be fundamental for biofilms, in terms of keeping cells in proximity and allowing for extended interaction, resource capture, mechanical strength and other properties, which emerge from the life of biofilm organisms, including enhanced tolerance to antimicrobials and other stress. The EPS components are extremely complex and dynamic and fulfil many functional roles, turning biofilms into the most ubiquitous and successful form of life on Earth.

Shine a light on immobilized enzymes: real-time sensing in solid supported biocatalysts

Enzyme immobilization on solid supports has been key to biotransformation development. Although technologies for immobilization have largely reached maturity, the resulting biocatalysts are not well understood mechanistically. One limitation is that their internal environment is usually inferred from external data. Therefore, biological consequences of the immobilization remain masked by physical effects of mass transfer, obstructing further development. Work reviewed herein shows that opto-chemical sensing performed directly within the solid support enables the biocatalyst's internal environment to be uncovered quantitatively and in real time. Non-invasive methods of intraparticle pH and O2 determination are presented, and their use as process analytical tools for development of heterogeneous biocatalysts is described. Method diversification to other analytes remains a challenging task for the future.

Biocidal effect of cathodic protection on bacterial viability in biofilm attached to carbon steel

Biofilm formed on carbon steel by various species of bacterial cells causes serious problems such as corrosion of steel, choking of flow in the pipe, deterioration of the heat-transfer efficiency, and so on. Cathodic protection is known to be a reliable method for protecting carbon steel from corrosion. However, the initial attachment of bacteria to the surface and the effects of cathodic protection on bacterial viability in the biofilm have not been clarified. In this study, cathodic protection was applied to an artificial biofilm containing Pseudomonas aeruginosa (PAO1), a biofilm constituent, on carbon steel. The aims of this study were to evaluate the inhibition effect of cathodic protection on biofilm formation and to reveal the inhibition mechanisms. The viability of PAO1 in artificial biofilm of 5 mm thickness on cathodically protected steel decreased to 1% of the initial cell concentration. Analysis of pH distribution in the artificial biofilm by pH microelectrode revealed that pH in proximity to carbon steel increased to approximately 11 after cathodic protection for 5 h. Moreover, 99% of region in the artificial biofilm was under the pH conditions of over nine. A simulation of pH profile was shown to correspond to experimental values. These results indicate cells in the artificial biofilm were killed or damaged by cathodic protection due to pH increase.

Cascade of bioreactors in series for conversion of 3-phospho-d-glycerate into d-ribulose-1,5-bisphosphate: kinetic parameters of enzymes and operation variables

A novel scheme employing enzymatic catalysts is described enabling conversion of D-ribulose-1,5-bisphosphate (RuBP) from 3-phospho-D-glycerate (3-PGA) without loss of carbon. Bioreactors harboring immobilized enzymes namely, phosphoglycerate kinase (PGK), glycerate phosphate dehydrogenase, triose phosphate isomerase (TIM), aldolase, transketolase (TKL), phosphatase (PTASE/FP), epimerase (EMR) and phosphoribulokinase (PRK), in accordance with this novel scheme were employed. These reactors were designed and constructed based on simulations carried out to study their performance under various operational conditions and allowed production of about 56 +/- 3% RuBP from 3-PGA. This method of synthesis of RuBP from 3-PGA employing immobilized enzyme bioreactors may be used for continuous regeneration of RuBP in biocatalytic carbon dioxide fixation processes from emissions where RuBP acts as acceptor of carbon dioxide to produce 3-PGA, rendering the fixation process continuous.

Influence of different cultivars on populations of ammonia-oxidizing bacteria in the root environment of rice

Comparisons of the activities and diversities of ammonia-oxidizing bacteria (AOB) in the root environment of different cultivars of rice (Oryza sativa L.) indicated marked differences despite identical environmental conditions during growth. Gross nitrification rates obtained by the 15N dilution technique were significantly higher in a modern variety, IR63087-1-17, than in two traditional varieties. Phylogenetic analysis based on the ammonium monooxygenase gene (amoA) identified strains related to Nitrosospira multiformis and Nitrosomonas europaea as the predominant AOB in our experimental rice system. A method was developed to determine the abundance of AOB on root biofilm samples using fluorescently tagged oligonucleotide probes targeting 16S rRNA. The levels of abundance detected suggested an enrichment of AOB on rice roots. We identified 40 to 69% of AOB on roots of IR63087-1-17 as Nitrosomonas spp., while this subpopulation constituted 7 to 23% of AOB on roots of the other cultivars. These results were generally supported by denaturing gradient gel electrophoresis of the amoA gene and analysis of libraries of cloned amoA. In hydroponic culture, oxygen concentration profiles around secondary roots differed significantly among the tested rice varieties, of which IR63087-1-17 showed maximum leakage of oxygen. The results suggest that varietal differences in the composition and activity of root-associated AOB populations may result from microscale differences in O2 availability.

Microbial-ecological significance of sulfide precipitation within anaerobic granular sludge revealed by micro-electrodes study

Micro-electrodes were applied to anaerobic granular sludge, which was developed in a UASB reactor, to examine intra-granule profiles with respect to pH, glucose and sulfide. When glucose was employed as a bulk liquid substrate, the micro-electrodes study demonstrated the pH behavior along granule depth: pH decrement at the granule exterior portion due to acid formation (buildup of acidity), and subsequent pH increment at the granule inner portion due to the consumption of acid (buildup of alkalinity). Sulfide micro-electrode proved sulfate reduction that mostly occurred at the granule exterior portion. Chemical equilibrium consideration evidently explained the occurrence of ferric sulfide predominantly in the interior portion, which accounts well for the morphology of a representative double-layered structure of granules grown on a low level of sulfite. Inorganic elements distribution within anaerobic granule was examined by electron probe X-ray micro analysis (EPMA) and ICP methods. The presence of crystalline calcium carbonate (calcite) was identified by X-ray diffraction analysis.

Location and limitation of cellulose production by Acetobacter xylinum established from oxygen profiles

The static fermentation of coconut water sucrose by Acetobacter xylinum was carried out at initial pH's of 3.0, 4.0, 5.0 or 6.0. Cellulose was produced at the surface, and its production was most favourable at pH's 4.0 and 5.0. These pH values also allowed for optimal bacterial growth. Oxygen concentration profiles were measured with microelectrodes at different cultivation stages, and steep profiles were obtained with penetration depths between 50 and 100 microm. A substrate penetration depth analysis confirmed the hypothesis that the first stage of the fermentation is entirely oxygen controlled. Diffusion calculations showed, however, that at a later stage sucrose becomes a limiting substrate also, which was confirmed by the decrease in cellulose production rate over time. The effective diffusion coefficient of oxygen in deactivated cellulose pellicles was measured with microelectrodes, and a value of 1.4 x 10(-9) m2/s was obtained under all investigated conditions. The oxygen flux was 5.9 x 10(-6) mol/m2.s, while a significantly higher value of 9.1 x 10(-6) mol/m2.s was obtained at pH 4.0.

Analyses of spatial distributions of sulfate-reducing bacteria and their activity in aerobic wastewater biofilms

The vertical distribution of sulfate-reducing bacteria (SRB) in aerobic wastewater biofilms grown on rotating disk reactors was investigated by fluorescent in situ hybridization (FISH) with 16S rRNA-targeted oligonucleotide probes. To correlate the vertical distribution of SRB populations with their activity, the microprofiles of O(2), H(2)S, NO(2)(-), NO(3)(-), NH(4)(+), and pH were measured with microelectrodes. In addition, a cross-evaluation of the FISH and microelectrode analyses was performed by comparing them with culture-based approaches and biogeochemical measurements. In situ hybridization revealed that a relatively high abundance of the probe SRB385-stained cells (approximately 10(9) to 10(10) cells per cm(3) of biofilm) were evenly distributed throughout the biofilm, even in the oxic surface. The probe SRB660-stained Desulfobulbus spp. were found to be numerically important members of SRB populations (approximately 10(8) to 10(9) cells per cm(3)). The result of microelectrode measurements showed that a high sulfate-reducing activity was found in a narrow anaerobic zone located about 150 to 300 microm below the biofilm surface and above which an intensive sulfide oxidation zone was found. The biogeochemical measurements showed that elemental sulfur (S(0)) was an important intermediate of the sulfide reoxidation in such thin wastewater biofilms (approximately 1,500 microm), which accounted for about 75% of the total S pool in the biofilm. The contribution of an internal Fe-sulfur cycle to the overall sulfur cycle in aerobic wastewater biofilms was insignificant (less than 1%) due to the relatively high sulfate reduction rate.

In situ analysis of nitrifying biofilms as determined by in situ hybridization and the use of microelectrodes

We investigated the in situ spatial organization of ammonia-oxidizing and nitrite-oxidizing bacteria in domestic wastewater biofilms and autotrophic nitrifying biofilms by using microsensors and fluorescent in situ hybridization (FISH) performed with 16S rRNA-targeted oligonucleotide probes. The combination of these techniques made it possible to relate in situ microbial activity directly to the occurrence of nitrifying bacterial populations. In situ hybridization revealed that bacteria belonging to the genus Nitrosomonas were the numerically dominant ammonia-oxidizing bacteria in both types of biofilms. Bacteria belonging to the genus Nitrobacter were not detected; instead, Nitrospira-like bacteria were the main nitrite-oxidizing bacteria in both types of biofilms. Nitrospira-like cells formed irregularly shaped aggregates consisting of small microcolonies, which clustered around the clusters of ammonia oxidizers. Whereas most of the ammonia-oxidizing bacteria were present throughout the biofilms, the nitrite-oxidizing bacteria were restricted to the active nitrite-oxidizing zones, which were in the inner parts of the biofilms. Microelectrode measurements showed that the active ammonia-oxidizing zone was located in the outer part of a biofilm, whereas the active nitrite-oxidizing zone was located just below the ammonia-oxidizing zone and overlapped the location of nitrite-oxidizing bacteria, as determined by FISH.

Characterization of the diffusive properties of biofilms using pulsed field gradient-nuclear magnetic resonance

The mobility of water in intact biofilms was measured with pulsed field gradient nuclear magnetic resonance (PFG-NMR) and used to characterise their diffusive properties. The results obtained with several well-defined systems, viz. pure water, agar, and agar containing inert particles or active bacteria were compared to glucose diffusion coefficients measured with micro-electrodes and those calculated utilising theoretical diffusion models. A good correspondence was observed indicating that PFG-NMR should also enable the measurement of diffusion coefficients in heterogeneous biological systems. Diffusion coefficients of several types of natural biofilms were measured as well and these results were related to the physical biofilm characteristics. The values had a high accuracy and reflected the properties of a sample of ca. 100 biofilms, while non-uniformity or non-geometrical shapes did not negatively influence the results. The monitored PFG-NMR signal contains supplementary information on e.g. cell fraction or spatial organisation but quantitative analysis was not yet possible. Copyright 1998 John Wiley & Sons, Inc.

pH and Glucose Profiles in Aggregates of Bacillus laevolacticus

Size distributions and glucose and pH profiles of aggregates of the d -(-)-lactic acid-producing organism Bacillus laevolacticus were measured. The organisms were grown in continuous culture with a medium glucose concentration of either 280 or 110 mM. A maximal aggregate diameter of 2.2 mm, with a Sauter mean of 1.46 mm, was determined for the former culture condition, whereas aggregates from a culture with 110 mM glucose input had a maximal diameter of 1.9 mm (Sauter mean of 1.07 mm). A pH gradient of approximately 2 U was observed for large aggregates (above 1.5 mm). In smaller aggregates (0.75 mm), the pH value in the interior part was approximately 0.4 U lower than that in the culture fluid. It could be concluded that, in cultures with the high glucose input, lactic acid accumulated within the aggregates to such an extent that metabolism in the central region of the larger aggregates could not proceed further. In these cultures, approximately 90% of the total biomass was active. In aggregates from cultures with a low glucose input, glucose only partly penetrated the larger-sized aggregates, and the activity of this culture was reduced to approximately 70% of the biomass. These aggregates were found to decrease in size after prolonged periods of cultivation. It is suggested that this is caused by glucose depletion in the interior of the aggregates. It is concluded that the availability of glucose is an important factor in determining the size of aggregates of B. laevolacticus.

Microelectrode Measurements of the Activity Distribution in Nitrifying Bacterial Aggregates

Microelectrodes for ammonium, oxygen, nitrate, and pH were used to study nitrifying aggregates grown in a fluidized-bed reactor. Local reactant fluxes and distribution of microbial activity could be determined from the microprofiles. The interfacial fluxes of the reactants closely reflected the stoichiometry of bacterial nitrification. Both ammonium consumption and nitrate production were localized in the outer shells, with a thickness of approximately 100 to 120 μm, of the aggregates. Under conditions in which ammonium and oxygen penetrated the whole aggregate, nitrification was restricted to this zone; oxygen was consumed in the central parts of the aggregates as well, probably because of oxidation of dead biomass. A sudden increase of the oxygen concentration to saturation (pure oxygen) was inhibitory to nitrification. The pH profiles showed acidification in the aggregates, but not to an inhibitory level. The distribution of activity was determined by the penetration depth of oxygen during aggregate development in the reactor. Mass transfer was significantly limited by the boundary layer surrounding the aggregates. Microelectrode measurements showed that the thickness of this layer was correlated with the diffusion coefficient of the species. Determination of the distribution of nitrifying activity required the use of ammonium or nitrate microelectrodes, whereas the use of oxygen microelectrodes alone would lead to erroneous results.

Determination of glucose diffusion coefficients in biofilms with micro-electrodes

A glucose micro-electrode was developed for direct measurements inside biofilms, and applied for the determination of effective diffusion coefficients in a model system of agar beads containing immobilized yeast cells. Two methods were used, one based on concentration gradients present at the liquid/solid interface of an active biofilm under steady-state conditions, the other based on the rate of glucose redistribution in an inactivated biofilm under transient-state conditions. Additional measurements with pH and oxygen micro-electrodes were performed and thus allowed for in-situ correction of the glucose electrode signal. From the micro-electrode measurements in the model system it was concluded that the glucose micro-sensor is a useful tool with which to obtain effective diffusion coefficients in biofilms.