Determination of polychlorinated biphenyls by liquid chromatography following cloud-point extraction

Compatibility of cloud point extraction with gas chromatography: Matrix effects of Triton X-100 on GC-MS and GC-MS/MS analysis of organochlorine and organophosphorus pesticides

Cloud point extraction is an environmentally benign and simple separation/concentration procedure that can be regarded as an alternative to classical liquid-liquid extraction. In the current work, it was studied the compatibility of cloud point extraction followed by back-extraction in low volume of organic solvent with gas chromatography-mass spectrometry (GC-MS and GC-MS/MS). Triton X-100 was preferred than Triton X-114 as a surfactant to produce the clouding phenomenon and hexane or isooctane was found to be appropriate organic solvents which can be used at the back-extraction step. It was observed that ca. 0.09 % w/w Triton X-100 was co-extracted in the organic phase (hexane or isooctane) so further study was carried out to find out its effect on the GC-MS (GC-MS/MS) measurement when liquid samples are injected without any pre-cleaning to remove the surfactant. The chromatographic separation and the mass detection were not deteriorated by the concomitant Triton X-100 for analysis of several Organochlorine and Organophosphorus pesticides (alpha-HCH, beta-HCH, gamma-HCH, Pentachlorobenzene, Hexachlorobenzene, Chlorpyrifos, Chlorpyrifos-methyl, Aldrin, Endrin, Dieldrin, alpha-Endosulfan, Heptachlor, Heptachlor-endo-epoxide-A, o,p-DDD, p,p-DDD, o,p-DDE, p,p-DDE, o,p-DDT and p,p-DDT). The stability of the GC system when introducing surfactant was assessed as acceptable (typically the peak area RSD% for 20 consecutive injections were below 5 %). Under the developed vaporization conditions using PTV or PSS injectors it can be deduced that Triton X-100 is deposited on the inner surface of the liner. This effect is beneficial since the resulting surfactant layer makes a surface which facilitates the pesticides transfer to the GC column. As a consequence, for some analytes, a substantial enhancement (up to 2.3 times) in the sensitivity was observed when the matrix-matched medium (0.09 % w/w Triton X-100 in organic solvent) is used compared to calibration in solely hexane or isooctane. Meanwhile, the measurement precision in the presence of Triton X-100 remains unchanged. The GC-MS/MS analysis was alternatively accomplished by the use of glass or metal liner and it was found that the glass one should be preferable. Finally, it can be concluded that cloud point extraction with Triton X-100 can be combined with GC-MS or GC-MS/MS analysis by applying liquid injection of the target analytes transferred in organic solvents such as hexane or isooctane. We have established a positive effect of Triton X-100 on the instrumental performance which is on opposite to the generally accepted concern of the negative influence of the surfactants on the gas chromatographic analysis.

Dynamic Microwave-Assisted Micelle Extraction Coupled with Cloud Point Preconcentration for the Determination of Triazine Herbicides in Soil

A green and simple method, dynamic microwave-assisted micelle extraction coupled with cloud point preconcentration, was developed for the determination of triazine herbicides in soil samples. The method has the advantages of those two extraction procedures, which could eliminate the interferences from complex soil samples greatly. Non-ionic surfactant Triton X-114 aqueous solution used as extraction solvent was continuously pumped into soil samples. The resulting extract was heated and centrifuged in the presence of NaCl. After centrifugation, the analytes were enriched into the surfactant-rich phase. No filtration or cleaning steps were required. Several key parameters were investigated. The Box-Behnken design was applied to optimize the experimental factors involved in the dynamic microwave-assisted micelle extraction. Good linearity was observed in the range of 1.00-250.00 μg kg-1. The limits of detection were ranged between 0.26 and 1.71 μg kg-1. The recoveries of analytes ranged from 80.3 to 98.3% with the relative standard deviations ranging from 1.1 to 6.6%.

Cloud point extraction coupled with back extraction: a green methodology in analytical chemistry

Recently, cloud point extraction (CPE) coupled with back extraction (BE) has been suggested as a promising alternative to liquid-liquid extraction. In CPE, non-ionic surfactants in aqueous solutions form micelles and the solution becomes turbid when heated to the cloud point temperature. Microwave- or ultrasonic-assisted BE can be performed after CPE and before injection of the sample for instrumental analysis by ultraviolet-visible spectroscopy, high-performance liquid chromatography, gas chromatography, gas chromatography-mass spectrometry, or liquid chromatography-mass spectrometry. This article reviews selected published scientific research on the application of CPE-BE to the determination of alkaloids, drugs and organophosphorus compounds from several complex matrices. This method could be scaled-up for use in forensic science.

Polyoxyethylene alkyl ether carboxylic acids: An overview of a neglected class of surfactants with multiresponsive properties

In this work, an overview on aqueous solutions of polyoxyethylene alkyl ether carboxylic acids is given. Unique properties arise from the combination of the nonionic, temperature-responsive polyoxyethylene block with the weakly ionic, pH-responsive carboxylic acid termination in a single surfactant headgroup. Accordingly, this class of surfactant finds broad application across very different sectors. Despite their large use on an industrial and a technical scale, the literature lacks a systematic and detailed characterization of their physico-chemical properties which is provided herein. In addition, a comprehensive overview is given of their self-assembly and interfacial behavior, of their use as colloidal building blocks and for large-scale applications.

A Simple Two-Step Cloud Point Extraction Process for Removing Fluorescent Whitening Agents VBL in Industrial Wastewater and Recycling of Surfactant

  With the enhancement of people's environmental consciousness, the treatment of wastewater was studied as the focus of this paper. Here we present a simple two-step extraction to realize efficient separation of fluorescent whitening agents VBL and cyclic utilization of surfactant to reduce the cost of wastewater treatment and environmental pollution. Firstly, the removal of VBL has been achieved by CPE using TX-114 as nonionic surfactant. The results showed that complete extraction was possible using 1% (w/w) TX-114 for VBL concentration not exceeding 17.5 mg/L, otherwise using a higher concentration of 1.5% (w/w) TX-114. Then the surfactant from the coacervate phase was recycled by changing the potential difference between phases. The morphology of micelles and solubilization mechanism of VBL were demonstrated through the observation of a fluorescent microscope. This method was successfully used to remove the VBL from wastewater sample and the surfactant could be reused several times.

Simultaneous preconcentration and determination of U(VI), Th(IV), Zr(IV) and Hf(IV) ions in aqueous samples using micelle-mediated extraction coupled to inductively coupled plasma-optical emission spectrometry

A simple cloud point extraction method followed by inductively coupled plasma-optical emission spectrometry (ICP-OES) was developed for simultaneous preconcentration and determination of trace amounts of U(VI), Th(IV), Zr(IV) and Hf(IV) ions in aqueous samples. The metal ions in 50 ml of aqueous solution (containing 0.1 M sodium acetate, pH 6.0) were formed complexes with dibenzoylmethane (DBM). Then, Triton X-114 (0.2%, w/v) was added to the solution. By increasing the temperature of the solution up to 50 degrees C, a phase separation occurred. After centrifugation at 4000 rpm for 6 min, the surfactant-rich phase (sediment phase) was diluted with 1.0 ml of 20:80 (v/v) of methanol/1 M HNO(3). The metal ions were then determined using ICP-OES. Finally, the main factors affecting the cloud point extraction were evaluated and optimized. Under optimized conditions, enhancement factors in the range of 37.0-43.6 were obtained. The calibration graphs were linear in the range of 0.5-1500 microg l(-1) for Th and Zr, 0.5-500 microg l(-1) for Hf and 2.5-1240 microg l(-1) for U with correlation coefficients (r(2)) better than 0.9926. The detection limits were between 0.1 and 1.0 microg l(-1) and the R.S.D. values for seven replicates were lower than 6.1%.

Simultaneous spectrophotometric determination of nitroaniline isomers after cloud point extraction by using least-squares support vector machines

Cloud point extraction has been used for the preconcentration of m-nitroaniline, o-nitroaniline and p-nitroaniline and later simultaneous spectrophotometric determination using polyethylene glycol tert-octylphenyl ether (Triton X-100) as surfactant. The resolution of a ternary mixture of the nitroaniline isomers (after extraction by cloud point) by the application of least-squares support vector machines (LS-SVM) was performed. The chemical parameters affecting the separation phase and detection process were studied and optimized. Under the optimum experimental conditions (i.e. pH 7.0, Triton X-100=0.6%, equilibrium time 20 min and cloud point 75 degrees C), calibration graphs were linear in the range of 0.2-20.0, 0.1-15.0 and 0.1-17.0 microg ml(-1) with detection limits of 0.08, 0.05 and 0.06 microg ml(-1) for m-nitroaniline, o-nitroaniline and p-nitroaniline, respectively. The experimental calibration matrix was designed with 21 mixtures of these chemicals. The concentrations were varied between calibration graphs concentrations of nitroaniline isomers. The root mean square error of prediction (RMSEP) for m-nitroaniline, o-nitroaniline and p-nitroaniline were 0.0146, 0.0308 and 0.0304, respectively. This procedure allows the simultaneous determination of nitroaniline isomers in synthetic and real matrix samples good reliability of the determination was proved.

Cloud point extraction coupled with HPLC-UV for the determination of phthalate esters in environmental water samples

A method based on cloud point extraction was developed to determine phthalate esters including di-ethyl-phthalate (DEP), di-(2-ethylhexyl)-phthalate (DEHP) and di-cyclohexyl-phthalate (DCP) in environmental water samples using high-performance liquid chromatography separation and ultraviolet detection (HPLC-UV). The non-ionic surfactant Triton X-114 was chosen as extraction solvent. The parameters affecting extraction efficiency, such as concentrations of Triton X-114 and Na2SO4, equilibration temperature, equilibration time and centrifugation time were evaluated and optimized. Under the optimum conditions, the method can achieve preconcentration factors of 35, 88, 111 and detection of limits of 2.0, 3.8, 1.0 ng/ml for DEP, DEHP and DCP in 10-ml water sample, respectively. The proposed method was successfully applied to the determination of trace amount of phathalate esters in effluent water of the wastewater treatment plant and the lixivium of plastic fragments.

Environmental analysis based on luminescence in organized supramolecular systems

The use of organized supramolecular systems-including micellar media and cyclodextrin inclusion complexes-combined with luminescence techniques in the study and determination of compounds and elements of environmental interest from 1990 to 2005 is reviewed. Analyses of environmental samples performed using fluorescence, photochemically induced fluorescence and phosphorescence spectroscopy as well as liquid chromatography, capillary electrophoresis and flow injection with luminescence detection in the presence of these organized media are described in detail.

Surfactant enhanced liquid-phase microextraction of basic drugs of abuse in hair combined with high performance liquid chromatography

The aim of this study was to evaluate the performance of a technique for simultaneous testing of hydrophilic abuse drugs in hair. The analysis of, codeine and methadone in morphine hair included incubation in methanol (5h, 50 degrees C), Surfactant enhanced liquid-phase microextraction (SE-LPME) and HPLC analysis. This study has demonstrated that SE-LPME constitute a real alternative to the other liquid-phase microextraction methods, for pre-concentration and extraction of hydrophilic drugs in biological samples and has shown the advantages of these optimized methodologies over the traditional microextraction techniques. For these drugs recoveries in the range of 57.5-93.7 were obtained from hair. The drugs were enriched by a factor of 61-128 during SE-LPME. Linearity (r2, 0.9982-0.9997) was obtained in the range of 50-500 microg/l for morphine and 10-500 microg/l for codeine and methadone.

Cloud Point Extraction Coupled with Microwave or Ultrasonic Assisted Back Extraction as a Preconcentration Step Prior to Gas Chromatography

Cloud point extraction of nonionic and anionic surfactants was applied as a preconcentration step prior to gas chromatography. No cleanup step preceded chromatographic analysis. The obtained surfactant-rich phase was treated with water-immiscible solvents, and the target analytes were back extracted by short-term microwave application or ultrasonication. A mixture of six PAHs (naphthalene, acenaphthene, fluorene, anthracene, fluoranthene, pyrene) was used as test compounds. The obtained detection limits were in the microgram per liter area. Recoveries of spiked water and soil samples ranged between 92 and 105% while analysis of certified reference materials gave results in good agreement with the certified values. Under the optimum experimental conditions, there was no interference or blocking of the column. According to our results, this approach presents a convenient solution to the up-to-date problem of combining gas chromatography with micellar cloud point extraction.

Dynamics of nonionic surfactant-rich phase separation and recovery of dyes

Cloud point separation of selected dyes was studied. The use of dyes made possible observation of the dynamics of surfactant-rich phase separation by color video. The pictures were interpreted by means of ImageC software and degrees of whiteness were calculated. It was found that separation was slow and equilibrium was not achieved even after a period of more than 10 h. The separated surfactant-rich phase had a heterogeneous structure. The globules of the surfactant-rich phase were also observed in the micellar aqueous phase. The surfactant concentration could be as high as one or two orders of magnitude above the expected cmc values and was not decreased to critical micelle concentration by centrifugation. The presence of sodium chloride was important and improved separation. Separation of dyes was in the range 73-98% and depended upon the surfactant, the temperature, the electrolyte content, and the dye. In each system considered, appropriate conditions had to be selected to obtain high recovery of the dye. The presence of the electrolyte was the most important parameter and it improved the separation of dyes. However, addition of the electrolyte could also account for precipitation of the dyes, as observed for the systems containing Direct Pink. The best recoveries were observed for Direct Yellow and oxyethylated nonylphenol (98% at 55 degrees C in the presence of NaCl). Centrifugation gave recoveries similar to those for prolonged heating but it shortened the time of phase separation.

Prediction of the behaviour of organic pollutants using cloud point extraction

A preconcentration study based on the cloud point phenomenon was carried out for a set of triazine herbicides, three of them chloro-substituted and three of them methylthio-substituted. Concentration factors and recoveries were calculated as function of the percentage of the non-ionic surfactant Triton X-114 employed. From these values, obtained from a cloud point extraction (CPE) procedure, the distribution coefficient between the Triton X-114 micelles and water, Kc, prior to CPE was calculated for each triazine and related to the corresponding octanol-water partition coefficient, Kow. In order to confirm the results obtained with the triazine herbicides, two sets of data from chemically different organic pollutants--organophosporous and chlorophenols--obtained from the literature were assessed, concluding that they display a similar behaviour to that of the triazine herbicides. This can be used to predict the CPE behaviour of other organic pollutants from their octanol-water partition coefficients. The Kc values were compared with the analyte concentration ratio in the surfactant-rich phase and aqueous phase (Ksa) with a view to obtaining a link between the analyte behaviour prior to and after cloud point extraction procedures.

Solid-phase extraction sorbent consisting of alkyltrimethylammonium surfactants immobilized onto strong cation-exchange polystyrene resin

Presented is a solid-phase extraction sorbent material composed of cationic alkyltrimethylammonium surfactants attached to a strong cation-exchange resin via ion-exchange. The original hydrophilic cation-exchange resin is made hydrophobic by covering the surface with alkyl chains from the hydrophobic portion of the surfactant. The sorbent material now has a better ability to extract hydrophobic molecules from aqueous samples. The entire stationary phase (alkyltrimethylammonium surfactant) is removed along with the analyte during the elution step. The elution step requires a mild elution solvent consisting of 0.25 M Mg2+ in a 50% 2-propanol solution. The main advantage of using a removable stationary phase is that traditionally utilized toxic elution solvents such as methylene chloride, which are necessary to efficiently release strongly hydrophobic species from SPE stationary phases, may now be avoided. Also, the final extract is directly compatible with reversed-phase liquid chromatography. The performance of this procedure is presented using pyrene as a test molecule.

Cloud-point extraction and preconcentration of cyanobacterial toxins (microcystins) from natural waters using a cationic surfactant

A new cloud-point extraction and preconcentration method using a cationic surfactant, Aliquat-336 (tricaprylylmethylammonium chloride), has been developed for the determination of cyanobacterial toxins, microcystins, in natural waters. Sodium sulfate was used to induce phase separation at 25 degrees C. The phase behavior of Aliquat-336 with respect to concentration of Na2SO4 was studied. The cloud-point system revealed a very high phase volume ratio compared to other established systems of nonionic, anionic, and cationic surfactants. At pH 6-7, it showed an outstanding selectivity in analyte extraction for anionic species. Only MC-LR and MC-YR, which are known to be predominantly anionic, were extracted (with averaged recoveries of 113.9 +/- 9% and 87.1 +/- 7%, respectively). MC-RR, which is likely to be amphoteric at the above pH range, was not detectable in the extract. Coupled to HPLC/UV separation and detection, the cloud-point extraction method (with 2.5 mM Aliquat-336 and 75 mM Na2SO4 at 25 degrees C) offered detection limits of 150 +/- 7 and 470 +/- 72 pg/mL for MC-LR and MC-YR, respectively, in 25 mL of deionized water. Repeatability of the method was 7.6% for MC-LR and 7.3% for MC-YR. The cloud-point extraction process can be completed within 10-15 min with no cleanup steps required. Applicability of the new method to the determination of microcystins in real samples was demonstrated using natural surface waters collected from a local river and a local duck pond spiked with realistic concentrations of microcystins. Effects of salinity and organic matter (TOC) content in the water sample on the extraction efficiency were also studied.

Use of non-ionic surfactant solutions for the extraction and preconcentration of phenolic compounds in water prior to their HPLC-UV detection

A simple and rapid HPLC method with spectrophotometric detection to determine phenolic compounds in water, including the 11 priority phenolic pollutants, is described. As they are present in low concentrations, an extraction and preconcentration step is necessary prior to their determination. A methodology based on the cloud point phenomenon is applied using the non-ionic surfactant oligoethylene glycol monoalkyl ether (Genapol X-080) as extractant. The optimum conditions for the extraction and preconcentration of phenolic derivatives have been established and detection limits lower than 10 micrograms L-1 were obtained for all studied compounds. The method has been applied to their determination in sea water and depurated waste water samples.

A novel cloud-point extraction process for preconcentrating selected polycyclic aromatic hydrocarbons in aqueous solution

A novel but simple cloud-point extraction (CPE) process is developed to preconcentrate the trace of selected polycyclic aromatic hydrocarbons (PAHs) with the use of the readily biodegradable nonionic surfactant Tergitol 15-S-7 as extractant. The concentrations of PAHs, mixtures of naphthalene and phenanthrene as well as pyrene, in the spiked samples were determined with the new CPE process at ambient temperature (23 degrees C) followed by high performance liquid chromatography(HPLC) with fluorescence detection. More than 80% of phenanthrene and pyrene, respectively, and 96% of naphthalene initially present in the aqueous solutions with concentrations near or below their aqueous solubilities were recovered using this new CPE process. Importantly Tergitol 15-S-7 does not give any fluorometric signal to interfere with fluorescence detection of PAHs in the UV range. No special washing step is, thus, required to remove surfactant before HPLC analyses. Different experimental conditions were studied. The optimum conditions for the preconcentration and determination of these selected PAHs at ambient temperature have been established as the following: (1) 3 wt% surfactant; (2) addition of 0.5 M Na2SO4; (3) 10 min for equilibration time; and (4) 3000 rpm for centrifugal speed with duration of 10 min.

Surfactant cloud point extraction and preconcentration of organic compounds prior to chromatography and capillary electrophoresis

The use of preconcentration steps based on phase separation by the cloud point technique offers a convenient alternative to more conventional extraction systems. It has been used successfully for the preconcentration of species of widely differing character and nature, such as metal ions, proteins and other biomaterials, or organic compounds of strongly differing polarity. Here we address the most recent analytical applications of this methodology when used as an isolation and trace enrichment step prior to the analysis of organic compounds (polycyclic aromatic hydrocarbons, polychlorinated compounds, pesticides, phenolic derivatives, aromatic amines, vitamins, etc.) via liquid and gas chromatography or capillary electrophoresis.

Alkyltrimethylammonium surfactant-mediated extractions: characterization of surfactant-rich and aqueous layers, and extraction performance

Most surfactants employed for extraction purposes contain strongly absorbing chromophores, and therefore cannot be used with the ultraviolet-visible HPLC detector because of the high background created. Alkyltrimethylammonium surfactants, which do not have strongly absorbing chromophores, have shown promise as an extractant compatible with HPLC-ultraviolet-visible detection. In our extraction procedure, alkyltrimethylammonium surfactants are added to a sample containing organic analytes in distilled water. Sodium chloride is next added, then the entire sample is shaken. Before centrifugation, 1-octanol is added to aid in the two phase formation of surfactant-rich and aqueous phases. In this paper, we present the results of our studies on the extraction behavior of an alkyltrimethylammonium surfactant technique using various organic compounds as test probes. Specifically studied are the extraction behavior of organic bases, isomers of varying polarity and a zwitterionic species that has different charges at various pH values. Results from multiple extractions to obtain quantitative recovery of analytes is also presented. The composition of each phase is elucidated through the interpretation of data obtained from thermogravimetric and carbon, hydrogen and nitrogen (CHN) instrumentation.

Determination of polycyclic aromatic hydrocarbons in marine sediments by high-performance liquid chromatography after microwave-assisted extraction with micellar media

A simple and rapid method is developed for extraction and determination of polycyclic aromatic hydrocarbons (PAHs) in marine sediments. The procedure was based on the microwave-assisted extraction of PAHs in marine sediment samples using a micellar medium of Polyoxyethylene 10 lauryl ether as extractant. Two-level factorial designs have been used to optimize the microwave extraction process. The analysis of extracts has been carried out by HPLC with UV detection. Fortified sediments gave an average recovery between 85.70 and 100.73%, with a relative standard deviation of 1.77-7.0% for PAHs with a ring number higher than three.