Dynamics of platelet glycoprotein IIb-IIIa receptor expression and fibrinogen binding. I. Quantal activation of platelet subpopulations varies with adenosine diphosphate concentration

A multi-constituent model for assessing the effect of impeller shroud on the thrombosis potential of a centrifugal blood pump

Centrifugal blood pumps can be used for treating heart failure patients. However, pump thrombosis has remained one of the complications that trouble clinical treatment. This study analyzed the effect of impeller shroud on the thrombosis risk of the blood pump, and predicted areas prone to thrombosis. Multi-constituent transport equations were presented, considering mechanical activation and biochemical activation. It was found that activated platelets concentration can increase with shear stress and adenosine diphosphate(ADP) concentration increasing, and the highest risk of thrombosis inside the blood pump was under extracorporeal membrane oxygenation (ECMO) mode. Under the same condition, ADP concentration and thrombosis index of semi-shroud impeller can increase by 7.3% and 7.2% compared to the closed-shroud impeller. The main reason for the increase in thrombosis risk was owing to elevated scalar shear stress and more coagulation promoting factor-ADP released. The regions with higher thrombosis potential were in the center hole, top and bottom clearance. As a novelty, the findings revealed that impeller shroud can influence mechanical and biochemical activation factors. It is useful for identifying potential risk regions of thrombus formation based on relative comparisons.

von Willebrand factor unfolding mediates platelet deposition in a model of high-shear thrombosis

Thrombosis under high-shear conditions is mediated by the mechanosensitive blood glycoprotein von Willebrand factor (vWF). vWF unfolds in response to strong flow gradients and facilitates rapid recruitment of platelets in flowing blood. While the thrombogenic effect of vWF is well recognized, its conformational response in complex flows has largely been omitted from numerical models of thrombosis. We recently presented a continuum model for the unfolding of vWF, where we represented vWF transport and its flow-induced conformational change using convection-diffusion-reaction equations. Here, we incorporate the vWF component into our multi-constituent model of thrombosis, where the local concentration of stretched vWF amplifies the deposition rate of free-flowing platelets and reduces the shear cleaning of deposited platelets. We validate the model using three benchmarks: in vitro model of atherothrombosis, a stagnation point flow, and the PFA-100, a clinical blood test commonly used for screening for von Willebrand disease (vWD). The simulations reproduced the key aspects of vWF-mediated thrombosis observed in these experiments, such as the thrombus location, thrombus growth dynamics, and the effect of blocking platelet-vWF interactions. The PFA-100 simulations closely matched the reported occlusion times for normal blood and several hemostatic deficiencies, namely, thrombocytopenia, vWD type 1, and vWD type 3. Overall, this multi-constituent model of thrombosis enables macro-scale 3D simulations of thrombus formation in complex geometries over a wide range of shear rates and accounts for qualitative and quantitative hemostatic deficiencies in patient blood.

A fibrin enhanced thrombosis model for medical devices operating at low shear regimes or large surface areas

Over the past decade, much of the development of computational models of device-related thrombosis has focused on platelet activity. While those models have been successful in predicting thrombus formation in medical devices operating at high shear rates (> 5000 s⁻¹), they cannot be directly applied to low-shear devices, such as blood oxygenators and catheters, where emerging information suggest that fibrin formation is the predominant mechanism of clotting and platelet activity plays a secondary role. In the current work, we augment an existing platelet-based model of thrombosis with a partial model of the coagulation cascade that includes contact activation of factor XII and fibrin production. To calibrate the model, we simulate a backward-facing-step flow channel that has been extensively characterized in-vitro. Next, we perform blood perfusion experiments through a microfluidic chamber mimicking a hollow fiber membrane oxygenator and validate the model against these observations. The simulation results closely match the time evolution of the thrombus height and length in the backward-facing-step experiment. Application of the model to the microfluidic hollow fiber bundle chamber capture both gross features such as the increasing clotting trend towards the outlet of the chamber, as well as finer local features such as the structure of fibrin around individual hollow fibers. Our results are in line with recent findings that suggest fibrin production, through contact activation of factor XII, drives the thrombus formation in medical devices operating at low shear rates with large surface area to volume ratios.

Patients treated with blood-contacting medical devices suffer from clotting complications. Over the past decades, a great effort has been made to develop computational tools to predict and prevent clot formation in these devices. However, most models have focused on platelet activity and neglected other important parts of the problem such as the coagulation cascade reactions that lead to fibrin formation. In the current work, we incorporate this missing element into a well-established and validated model for platelet activity. We then use this novel approach to predict thrombus formation in two experimental configurations. Our results confirm that to accurately predict the clotting process in devices where surface area to volume ratios are large and flow velocity and shear stresses remain low, coagulation reactions and subsequent fibrin formation must be considered. This new model could have great implications for the design and optimization of medical devices such as blood oxygenators. In the long term, the model could evolve into a functional tool to inform anticoagulation therapies for these patients.

Toward modeling thrombosis and thromboembolism in laminar and turbulent flow regimes

Thrombosis and thromboembolism are deadly risk factors in blood-contacting biomedical devices, and in-silico models of thrombosis are attractive tools to understand the mechanics of these processes, though the simulation of thromboembolism remains underdeveloped. The purpose of this study is to modify an existing computational thrombosis model to allow for thromboembolism and to investigate the behavior of the modified model at a range of flow rates. The new and existing models are observed to lead to similar predictions of thrombosis in a canonical backward-facing step geometry across flow rates, and neither model predicts thrombosis in a turbulent flow. Simulations are performed by increasing flow rates in the case of a clot formed at lower flow to induce embolization. While embolization is observed, most of the clot breakdown is by shear rather than by breakup and subsequent transport of clotted material, and further work is required in the formulation and validation of embolization. This model provides a framework to further investigate thromboembolization.

An Accelerated Thrombosis Model for Computational Fluid Dynamics Simulations in Rotary Blood Pumps

Purpose

Thrombosis ranks among the major complications in blood-carrying medical devices and a better understanding to influence the design related contribution to thrombosis is desirable. Over the past years many computational models of thrombosis have been developed. However, numerically cheap models able to predict localized thrombus risk in complex geometries are still lacking. The aim of the study was to develop and test a computationally efficient model for thrombus risk prediction in rotary blood pumps.

Methods

We used a two-stage approach to calculate thrombus risk. The first stage involves the computation of velocity and pressure fields by computational fluid dynamic simulations. At the second stage, platelet activation by mechanical and chemical stimuli was determined through species transport with an Eulerian approach. The model was compared with existing clinical data on thrombus deposition within the HeartMate II. Furthermore, an operating point and model parameter sensitivity analysis was performed.

Results

Our model shows good correlation (R² > 0.93) with clinical data and identifies the bearing and outlet stator region of the HeartMate II as the location most prone to thrombus formation. The calculation of thrombus risk requires an additional 10–20 core hours of computation time.

Conclusion

The concentration of activated platelets can be used as a surrogate and computationally low-cost marker to determine potential risk regions of thrombus deposition in a blood pump. Relative comparisons of thrombus risk are possible even considering the intrinsic uncertainty in model parameters and operating conditions.

Supplementary Information

The online version contains supplementary material available at 10.1007/s13239-021-00606-y.

Continuum modeling of thrombus formation and growth under different shear rates

Obstruction of blood flow due to thrombosis is a major cause of ischemic stroke, myocardial infarction, and in severe cases, mortality. In particular, in blood wetting medical devices, thrombosis is a common reason for failure. The prediction of thrombosis by understanding signaling pathways using computational models, lead to identify the risk of thrombus formation in blood-contacting devices and design improvements. In this study, a mathematical model of thrombus formation and growth is presented. A biochemical model of platelet activation and aggregation is developed to predict thrombus size and shape at the site of vascular injury. Computational fluid dynamics using the finite volume method is employed to compute the velocity and pressure fields which are influenced by the growing thrombi. The passive transport of platelets, agonists, the platelet activation kinetics, their adhesion to the growing thrombi and embolization of platelets are solved by a fully coupled set of convection-diffusion-reaction equations. The thrombogenic surface representing blood-contacting material or injured blood vessel was incorporated into the model as a surface flux boundary condition to initiate thrombus formation. The blood is considered as a Newtonian fluid, while the thrombus is treated as a porous medium. The results are compared with in vitro experiments of a microfluidic chamber at an initial inlet venous shear rate of 200s^-1 using a pressure-inlet boundary condition. The thrombus development due to agonist concentrations and change in the shear rate as well as thromboembolism for this benchmark problem is successfully computed. Furthermore, to extend the current model to a physiologically relevant configuration, thrombus formation in a blood tube is simulated. Two different heterogeneous reaction rates for platelet aggregation are used to simulate thrombus growth under a constant inlet flow rate. The findings show that the thrombus shape can be substantially altered by the hemodynamic conditions, increase in the shear rate and due to the combined effects of shear induced platelet activation and the heterogeneous reaction rates. It is also concluded that the model is able to predict thrombus formation in different physiological and pathological hemodynamics.

Polydiacetylene Liposome Microarray toward Facile Measurement of Platelet Activation in Whole Blood

The necessity of a simple measurement of platelet activation has been increasing in clinical medicine to regulate the proper dose of the antiplatelet drugs for patients having clinical outcomes in acute situations such as angina pectoris, stroke, or peripheral vascular disease or procedures involving angioplasty or coronary thrombolysis. We developed a self-signaling polydiacetylene (PDA) liposome microarray to detect activated platelets from whole blood samples in a single step. A specific antibody, 9F9 antibody, to platelet-bound fibrinogen was selected and conjugated to the PDA liposome microarray to quantify the fibrinogen-bound platelets. The developed PDA liposome-9F9 microarray generated an intense fluorescence signal when activated platelets in whole blood were introduced and also successfully distinguished the reduced platelet activation in the presence of Tirofiban, a model antiplatelet drug. The results of this single-step benchtop assay incorporates simple, sensitive, and rapid attributes that can detect the extent of platelet activation prior to needed clinical procedures.

Refining a numerical model for device-induced thrombosis and investigating the effects of non-Newtonian blood models

Thrombosis is one of the main causes of failure in device implantation. Computational thrombosis simulation is a convenient approach to evaluate the risk of thrombosis for a device. However, thrombosis is a complicated process involving multiple species and reactions. Application of a macroscopic, single-scale computational model for device-induced thrombosis is a cost-effective approach. The current study has refined an existing thrombosis model, which simulated thrombosis by tracing four species in blood: non-activated platelets, activated platelets, surface adherent platelets, and ADP. Platelets are activated mechanically by shear stress, and chemically by ADP. Platelet adhesion occurs on surfaces with low wall shear stress with platelet aggregation inhibited in regions of high shear stress. The study improves the existing thrombosis model by: 1) Modifying the chemical platelet activation function so that ADP activates platelets; 2) Modifying the function describing thrombus deposition and growth to distinguish between thrombus deposition on wall surfaces and thrombus growth on existing thrombus surfaces; 3) Modifying the thrombus breakdown function to allow for thrombus breakdown by shear stress; 4) Modeling blood flow as non-Newtonian. The results show that the inclusion of ADP and the use of a non-Newtonian model improve agreement with experimental data.

Simulation of thrombosis in a stenotic microchannel: The effects of vWF-enhanced shear activation of platelets

This study was undertaken to develop a numerical/computational simulation of von Willebrand Factor (vWF) - mediated platelet shear activation and deposition in an idealized stenosis. Blood is treated as a multi-constituent mixture comprised of a linear fluid component and a porous solid component (thrombus). Chemical and biological species involved in coagulation are modeled using a system of coupled convection-reaction-diffusion (CRD) equations. This study considers the cumulative effect of shear stress (history) on platelet activation. The vWF activity is modeled as an enhancement function for the shear stress accumulation and is related to the experimentally-observed unfolding rate of vWF. A series of simulations were performed in an idealized stenosis in which the predicted platelets deposition agreed well with previous experimental observations spatially and temporally, including the reduction of platelet deposition with decreasing expansion angle. Further simulation indicated a direct relationship between vWF-mediated platelet deposition and degree of stenosis. Based on the success with these benchmark simulations, it is hoped that the model presented here may provide additional insight into vWF-mediated thrombosis and prove useful for the development of more hemo-compatible blood-wetted devices in the future.

Chemical Equilibrium at the Tick-Host Feeding Interface:A Critical Examination of Biological Relevance in Hematophagous Behavior

Ticks secrete hundreds to thousands of proteins into the feeding site, that presumably all play important functions in the modulation of host defense mechanisms. The current review considers the assumption that tick proteins have functional relevance during feeding. The feeding site may be described as a closed system and could be treated as an ideal equilibrium system, thereby allowing modeling of tick-host interactions in an equilibrium state. In this equilibrium state, the concentration of host and tick proteins and their affinities will determine functional relevance at the tick-host interface. Using this approach, many characterized tick proteins may have functional relevant concentrations and affinities at the feeding site. Conversely, the feeding site is not an ideal closed system, but is dynamic and changing, leading to possible overestimation of tick protein concentration at the feeding site and consequently an overestimation of functional relevance. Ticks have evolved different possible strategies to deal with this dynamic environment and overcome the barrier that equilibrium kinetics poses to tick feeding. Even so, cognisance of the limitations that equilibrium binding place on deductions of functional relevance should serve as an important incentive to determine both the concentration and affinity of tick proteins proposed to be functional at the feeding site.

Platelet activity and hypercoagulation in type 2 diabetes

Background

A strong correlation exists between type 2 diabetes mellitus (T2DM) and cardiovascular disease (CVD), with CVD and the presence of atherosclerosis being the prevailing cause of morbidity and mortality in diabetic populations. T2DM is accompanied by various coagulopathies, including anomalous clot formation or amyloid fibrin(ogen), the presence of dysregulated inflammatory molecules. Platelets are intimately involved in thrombus formation and particularly vulnerable to inflammatory cytokines.

Methods

The aim of this current study was therefore to assess whole blood (hyper)coagulability, platelet ultrastructure and receptor expression, as well as the levels of IL-1β, IL-6, IL-8 and sP-selectin in healthy and diabetic individuals. Platelet morphology was assessed through scanning electron microscopy (SEM), while assessment of GPIIb/IIIa receptor expression was performed with confocal microscopy and flow cytometry with the addition of FITC-PAC-1 and CD41-PE antibodies. IL-1β, IL-6 and IL-8 and sP-selectin levels were assessed using a multiplex assay.

Results

In T2DM there is significant upregulation of circulating inflammatory markers, hypercoagulation and platelet activation, with increased GPIIb/IIIa receptor expression, as seen with flow cytometry and confocal microscopy. Analyses showed that these receptors were additionally shed onto microparticles, which was confirmed with SEM.

Conclusions

Cumulatively, this provides mechanistic evidence that pathological states of platelets together with amyloid fibrin(ogen) in T2DM, might underpin an increased risk for cardiovascular events.

Prediction of Thrombus Growth: Effect of Stenosis and Reynolds Number

Shear stresses play a major role in platelet-substrate interactions and thrombus formation and growth in blood flow, where under both pathological and physiological conditions platelet adhesion and accumulation occur. In this study, a shear-dependent continuum model for platelet activation, adhesion and aggregation is presented. The model was first verified under three different shear conditions and at two heparin levels. Three-dimensional simulations were then carried out to evaluate the performance of the model for severely damaged (stripped) aortas with mild and severe stenosis degrees in laminar flow regime. For these cases, linear shear-dependent functions were developed for platelet-surface and platelet-platelet adhesion rates. It was confirmed that the platelet adhesion rate is not only a function of Reynolds number (or wall shear rate) but also the stenosis severity of the vessel. General correlations for adhesion rates of platelets as functions of stenosis and Reynolds number were obtained based on these cases. Finally using the new platelet adhesion rates, the model was applied to different experimental systems and shown to agree well with measured platelet deposition.

Multi-Constituent Simulation of Thrombus Deposition

In this paper, we present a spatio-temporal mathematical model for simulating the formation and growth of a thrombus. Blood is treated as a multi-constituent mixture comprised of a linear fluid phase and a thrombus (solid) phase. The transport and reactions of 10 chemical and biological species are incorporated using a system of coupled convection-reaction-diffusion (CRD) equations to represent three processes in thrombus formation: initiation, propagation and stabilization. Computational fluid dynamic (CFD) simulations using the libraries of OpenFOAM were performed for two illustrative benchmark problems: in vivo thrombus growth in an injured blood vessel and in vitro thrombus deposition in micro-channels (1.5 mm × 1.6 mm × 0.1 mm) with small crevices (125 μm × 75 μm and 125 μm × 137 μm). For both problems, the simulated thrombus deposition agreed very well with experimental observations, both spatially and temporally. Based on the success with these two benchmark problems, which have very different flow conditions and biological environments, we believe that the current model will provide useful insight into the genesis of thrombosis in blood-wetted devices, and provide a tool for the design of less thrombogenic devices.

Development of a computational model for macroscopic predictions of device-induced thrombosis

While cardiovascular device-induced thrombosis is associated with negative patient outcomes, the convoluted nature of the processes resulting in a thrombus makes the full thrombotic network too computationally expensive to simulate in the complex geometries and flow fields associated with devices. A macroscopic, continuum computational model is developed based on a simplified network, which includes terms for platelet activation (chemical and mechanical) and thrombus deposition and growth in regions of low wall shear stress (WSS). Laminar simulations are performed in a two-dimensional asymmetric sudden expansion geometry and compared with in vitro thrombus size data collected using whole bovine blood. Additionally, the predictive power of the model is tested in a flow cell containing a series of symmetric sudden expansions and contractions. Thrombi form in the low WSS area downstream of the asymmetric expansion and grow into the nearby recirculation region, and thrombus height and length largely remain within 95 % confidence intervals calculated from the in vitro data for 30 min of blood flow. After 30 min, predicted thrombus height and length are 0.94 and 4.32 (normalized by the 2.5 mm step height). Importantly, the model also correctly predicts locations of thrombus deposition observed in the in vitro flow cell of expansions and contractions. As the simulation results, which rely on a greatly reduced model of the thrombotic network, are still able to capture the macroscopic behavior of the full network, the model shows promise for timely predictions of device-induced thrombosis toward optimizing and expediting the device development process.

Modelling of platelet-fibrin clot formation in flow with a DPD-PDE method

The paper is devoted to mathematical modelling of clot growth in blood flow. Great complexity of the hemostatic system dictates the need of usage of the mathematical models to understand its functioning in the normal and especially in pathological situations. In this work we investigate the interaction of blood flow, platelet aggregation and plasma coagulation. We develop a hybrid DPD-PDE model where dissipative particle dynamics (DPD) is used to model plasma flow and platelets, while the regulatory network of plasma coagulation is described by a system of partial differential equations. Modelling results confirm the potency of the scenario of clot growth where at the first stage of clot formation platelets form an aggregate due to weak inter-platelet connections and then due to their activation. This enables the formation of the fibrin net in the centre of the platelet aggregate where the flow velocity is significantly reduced. The fibrin net reinforces the clot and allows its further growth. When the clot becomes sufficiently large, it stops growing due to the narrowed vessel and the increase of flow shear rate at the surface of the clot. Its outer part is detached by the flow revealing the inner part covered by fibrin. This fibrin cap does not allow new platelets to attach at the high shear rate, and the clot stops growing. Dependence of the final clot size on wall shear rate and on other parameters is studied.

A simplified mathematical model for thrombin generation

A new phenomenological mathematical model based directly on laboratory data for thrombin generation and having a patient-specific character is described. A set of the solved equations for cell-based models of blood coagulation that can reproduce the temporal evolution of thrombin generation is proposed; such equations are appropriate for use in computational fluid dynamic (CFD) simulations. The initial values for the reaction rates are either taken from already existing model or experimental data, or they can obtained from simple reasoning under certain assumptions; it is shown that coefficients can be adjusted in order to fit a range of different thrombin generation curves as derived from thrombin generation assays. The behaviour of the model for different platelet concentration seems to be in good agreement with reported experimental data. It is shown that the reduced set of equations used represents to a good approximation a low-order model of the detailed mechanism and thus it can represent a cost-effective and-case specific mathematical model of coagulation reactions up to thrombin generation.

Platelet adhesion from shear blood flow is controlled by near-wall rebounding collisions with erythrocytes

The efficacy of platelet adhesion in shear flow is known to be substantially modulated by the physical presence of red blood cells (RBCs). The mechanisms of this regulation remain obscure due to the complicated character of platelet interactions with RBCs and vascular walls. To investigate this problem, we have created a mathematical model that takes into account shear-induced transport of platelets across the flow, platelet expulsion by the RBCs from the near-wall layer of the flow onto the wall, and reversible capture of platelets by the wall and their firm adhesion to it. This model analysis allowed us to obtain, for the first time to our knowledge, an analytical determination of the platelet adhesion rate constant as a function of the wall shear rate, hematocrit, and average sizes of platelets and RBCs. This formula provided a quantitative description of the results of previous in vitro adhesion experiments in perfusion chambers. The results of the simulations suggest that under a wide range of shear rates and hematocrit values, the rate of platelet adhesion from the blood flow is mainly limited by the frequency of their near-wall rebounding collisions with RBCs. This finding reveals the mechanism by which erythrocytes physically control platelet hemostasis.

Aggregometry detects platelet hyperreactivity in healthy individuals

Aggregometry is widely used to assess platelet function, but its use in identifying platelet hyperreactivity is poorly defined. We studied platelet aggregation in 359 healthy individuals using the agonists adenosine diphosphate (ADP), epinephrine, collagen, collagen-related peptide, and ristocetin. We also assessed the reproducibility of these assays in 27 subjects by studying them repeatedly on at least 4 separate occasions. Healthy subjects exhibited considerable interindividual variability in aggregation response to agonists, especially at concentrations lower than those typically used in clinical laboratories. For each agonist tested at these submaximal concentrations, a small proportion of individuals demonstrated an unusually robust aggregation response. Subjects who exhibited such in vitro hyperreactivity to one agonist tended to demonstrate a similar response to others, suggesting that hyperreactivity is a global characteristic of platelets. Epinephrine and collagen-related peptide were especially reliable and efficient in detecting hyperreactivity. For epinephrine, excellent reproducibility persisted for up to 3 years, and hyperreactivity was associated with female sex and higher fibrinogen levels (P < .02). We recommend these assays as appropriate candidates for future studies requiring accurate assessment of increased platelet reactivity. These include clinical studies to improve risk assessment for arterial thrombosis, as well as genetic studies to establish determinants of the hyperreactive platelet phenotype.

Highly constrained cyclic (S,S) -CXaaC- peptides as inhibitors of fibrinogen binding to platelets

The Arg-Gly-Asp RGD motif of adhesive proteins is recognized by the activated platelet integrin alpha(IIb)beta3. Binding of fibrinogen (Fg) to activated alpha(IIb)beta3 causes platelet aggregation and thrombus formation. Highly constraint cyclic (S,S) -CXaaC- containing peptides incorporating the (S,S) -CDC- and (S,S) -CRC- motifs were tested for their ability to inhibit platelet aggregation and Fg binding. Our results suggest that the above cyclic scaffolds stabilize a favorable structure for the antiaggregatory activity (IC50-values ranged from 1.7 to 570 microm). The peptides inhibited Fg binding with IC50-values up to 30-fold lower than those determined for the inhibition of the adenosine diphosphate (ADP)-induced platelet aggregation. Importantly, peptides (S,S) PSRCDCR-NH2 (peptide 11) and (S,S) PRCDCK-NH2 (peptide 10) did not inhibit PAC-1 binding to the activated platelets at a concentration in which they completely inhibited Fg binding. Moreover, (S,S) PSRCDCR-NH(2) (peptide 11), one of the more active peptides, inhibited ADP-induced P-selectin exposure. By contrast, peptide (S,S) Ac-RWDCRC-NH2, incorporating the inverse (S,S) -DCRC- sequence (peptide 16), failed to inhibit P-selectin exposure whereas at the same concentration, it effectively inhibited PAC-1 and Fg binding. It is concluded that peptides containing the (S,S) -CDC- as well the (S,S) -CRC- sequences, exhibit a broad range of activities toward platelets, and could be helpful tools for elucidating the structural interaction of Fg with the integrin receptor alpha(IIb)beta3, in its activated form. Furthermore, the (S,S) -RCDC- sequence can be used as a scaffold for developing potent non-RGD-like Fg-binding inhibitors.

Computational Model of Device-Induced Thrombosis and Thromboembolism

A numerical model of thrombosis/thromboembolism (T/TE) is presented that predicts the progression of thrombus growth and thromboembolization in low-shear devices (hemodialyzers, oxygenators, etc.). Coupled convection-diffusion-reaction equations were solved to predict velocities, platelet agonist (ADP, thromboxane A2, and thrombin) concentrations, agonist-induced and shear-induced platelet activation, and platelet transport and adhesion to biomaterial surfaces and adherent platelets (hence, thrombus growth). Single-platelet and thrombus embolization were predicted from shear forces and surface adhesion strengths. Values for the platelet-biomaterial reaction constant and the platelet adhesion strength were measured in specific experiments, but all other parameter values were obtained from published sources. The model generated solutions for sequential time steps, while adjusting velocity patterns to accommodate growing surface thrombi. Heparinized human blood was perfused (0.75 ml/min) through 580 microm-ID polyethylene flow cells with flow contractions (280 microm-ID). Thrombus initiation, growth, and embolization were observed with videomicroscopy, while embolization was confirmed by light scattering, and platelet adhesion was determined by scanning electron microscopy. Numerical predictions and experimental observations were similar in indicating: 1) the same three thrombotic locations in the flow cell and the relative order of thrombus development in those locations, 2) equal thrombus growth rates on polyethylene and silicon rubber (in spite of differing overall T/TE), and 3) similar effects of flow rate (1.5 ml/min versus 0.75 ml/min) on platelet adhesion and thrombosis patterns.

Effect of synthetic peptides corresponding to residues 313-332 of the alphaIIb subunit on platelet activation and fibrinogen binding to alphaIIbbeta3

The platelet integrin receptor alphaIIbbeta3 plays a critical role in thrombosis and haemostasis by mediating interactions between platelets and several ligands but primarily fibrinogen. It has been shown previously that the YMESRADR KLAEVGRVYLFL (313-332) sequence of the alphaIIb subunit plays an important role in platelet activation, fibrinogen binding and alphaIIbbeta3-mediated outside-in signalling. Furthermore, we recently showed that the 20-residue peptide (20-mer) alphaIIb 313-332, is a potent inhibitor of platelet aggregation and fibrinogen binding to alphaIIbbeta3, interacting with fibrinogen rather than the receptor. In an effort to determine the sequence and the minimum length required for the biological activity of the above 20-mer, we synthesized seven octapeptides, each overlapping by six residues, covering the entire sequence and studied their effect on platelet activation as well as fibrinogen binding to activated platelets. We show for the first time that octapeptides containing the RAD sequence are capable of inhibiting platelet aggregation and secretion as well as fibrinogen binding to the activated alphaIIbbeta3, possibly interacting with the ligand rather than the receptor. This suggests that the RAD sequence, common to all the inhibitory peptides, is critical for their biological activity. However, the presence of the YMES sequence, adjacent to RAD, significantly increases the peptide's biological potency. The development of such inhibitors derived from the 313-332 region of the alphaIIb subunit may be advantageous against the RGD-like antagonists as they could inhibit platelet activation without interacting with alphaIIbbeta3, thus failing to further induce alphaIIbbeta3-mediated outside-in signalling.

Mapping the binding domains of the alpha(IIb) subunit. A study performed on the activated form of the platelet integrin alpha(IIb)beta(3)

alpha(IIb)beta(3), a member of the integrin family of adhesive protein receptors, is the most abundant glycoprotein on platelet plasma-membranes and binds to adhesive proteins via the recognition of short amino acid sequences, for example the ubiquitous RGD motif. However, elucidation of the ligand-binding domains of the receptor remains controversial, mainly owing to the fact that integrins are conformationally labile during purification and storage. In this study, a detailed mapping of the extracellular region of the alpha(IIb) subunit is presented, using overlapping 20-peptides, in order to identify the binding sites of alpha(IIb) potentially involved in the platelet-aggregation event. Regions alpha(IIb) 313-332, alpha(IIb) 265-284 and alpha(IIb) 57-64 of alpha(IIb)beta(3) were identified as putative fibrinogen-binding domains because the corresponding peptides inhibited platelet aggregation and antagonized fibrinogen association, possibly by interacting with this ligand. The latter is further supported by the finding that the above peptides did not interfere with the binding of PAC-1 to the activated form of alpha(IIb)beta(3). Furthermore, alpha(IIb) 313-332 was found to bind to fibrinogen in a solid-phase binding assay. It should be emphasized that all the experiments in this study were carried out on activated platelets and consequently on the activated form of this integrin receptor. We hypothesize that RAD and RAE adhesive motifs, encompassed in alpha(IIb) 313-332, 265-284 and 57-64, are capable of recognizing complementary domains of fibrinogen, thus inhibiting the binding of this ligand to platelets.

A Model Incorporating Some of the Mechanical and Biochemical Factors Underlying Clot Formation and Dissolution in Flowing Blood

Multiple interacting mechanisms control the formation and dissolution of clots to maintain blood in a state of delicate balance. In addition to a myriad of biochemical reactions, rheological factors also play a crucial role in modulating the response of blood to external stimuli. To date, a comprehensive model for clot formation and dissolution, that takes into account the biochemical, medical and rheological factors, has not been put into place, the existing models emphasizing either one or the other of the factors. In this paper, after discussing the various biochemical, physiologic and rheological factors at some length, we develop a model for clot formation and dissolution that incorporates many of the relevant crucial factors that have a bearing on the problem. The model, though just a first step towards understanding a complex phenomenon, goes further than previous models in integrating the biochemical, physiologic and rheological factors that come into play.

Platelet GP IIIa Pl(A) polymorphisms display different sensitivities to agonists

BACKGROUND

Both inherited predisposition and platelet hyperreactivity have been associated with ischemic coronary events, but mechanisms that support genetic differences among platelets from different subjects are generally lacking. Associations between the platelet Pl(A2) polymorphism of GP IIIa and coronary syndromes raise the question as to whether this inherited variation may contribute to platelet hyperreactivity.

METHODS AND RESULTS

In this study, we characterized functional parameters in platelets from healthy donors with the Pl(A) (HPA-1) polymorphism, a Leu (Pl(A1)) to Pro (Pl(A2)) substitution at position 33 of the GP IIIa subunit of the platelet GP IIb/IIIa receptor (integrin alpha(IIb)beta(3)). We studied 56 normal donors (20 Pl(A1,A1), 20 Pl(A1,A2), and 16 Pl(A2,A2)). Compared with Pl(A1,A1) platelets, Pl(A2)-positive platelets showed a gene dosage effect for significantly greater surface-expressed P-selectin, GP IIb/IIIa-bound fibrinogen, and activated GP IIb/IIIa in response to low-dose ADP. Surface expression of GP IIb/IIIa was similar in resting platelets of all 3 genotypes but was significantly greater on Pl(A2,A2) platelets after ADP stimulation (P=0.003 versus Pl(A1,A1); P=0.03 versus Pl(A1,A2)). Pl(A1,A2) platelets were more sensitive to inhibition of aggregation by pharmacologically relevant concentrations of aspirin and abciximab.

CONCLUSIONS

Pl(A2)-positive platelets displayed a lower threshold for activation, and platelets heterozygous for Pl(A) alleles showed increased sensitivity to 2 antiplatelet drugs. These in vitro platelet studies may have relevance for in vivo thrombotic conditions.

Low-density lipoprotein enhances platelet secretion via integrin-alphaIIbbeta3-mediated signaling

LDL is known to increase the sensitivity of human platelets for agonists and to induce aggregation and secretion independently at high concentrations, but its mechanism of action is largely obscure. To clarify how LDL increases platelet sensitivity, cells were incubated in lipoprotein-poor plasma and treated with collagen at a concentration that induced approximately 20% secretion of 14C-serotonin. Preincubation with LDL (30 minutes at 37 degreesC) enhanced secretion in a dose-dependent manner to 60+/-14% at a concentration of 2 g LDL protein/L. Similar stimulation by LDL was seen when secretion was induced by the thrombin receptor-activating peptide. This enhancement was strongly reduced (1) in the presence of monoclonal antibody PAC1 against activated alphaIIbbeta3, a polyclonal antibody against alphaIIb, and in the presence of the fibrinogen peptides GRGDS and HHLGGAKQAGDV; (2) in alphaIIbbeta3-deficient platelets; and (3) after dissociation of alphaIIbbeta3. In contrast, binding of 125I-LDL to normal platelets in the presence of PAC1, anti-alphaIIb, GRGDS, and HHLGGAKQAGDV, and to alphaIIbbeta3-deficient platelets was normal. LDL increased the surface expression of fibrinogen in lipoprotein-poor plasma and fibrinogen-free medium, suggesting that extracellular and granular fibrinogen bind to alphaIIbbeta3 after platelet-LDL interaction. Platelets deficient in fibrinogen (<0.5% of normal) or von Willebrand Factor (<1% of normal) but containing normal amounts of other ligands for alphaIIbbeta3 preserved responsiveness to LDL, indicating that occupancy of alphaIIbbeta3 was not restricted to fibrinogen. Inhibition of protein kinase C (bisindolylmaleimide) diminished fibrinogen binding and sensitization by LDL; inhibition of tyrosine kinases (herbimycin A) left fibrinogen binding unchanged but diminished sensitization by LDL. We conclude that an increased concentration of LDL, such as observed in homozygous familial hypercholesterolemia, sensitizes platelets to stimulation by collagen and thrombin receptor-activating peptide via ligand-induced outside-in signaling through integrin-alphaIIbbeta3.

Platelet aggregation in flow: differential roles for adhesive receptors and ligands

This article addresses the flow-dependent differential roles of the platelet receptors, glycoprotein (GP) GPIb and GPIIb-IIIa, in platelet aggregation mediated by ristocetin and soluble von Willebrand factor (vWF), by adenosine diphosphate (ADP) and soluble fibrinogen (Fg), and by thrombin and ADP in absence of exogenous ligands. Platelet-rich plasma or "activated" washed platelets were sheared in a coaxial cylinder at 100 to 1000 sec(-1) or in tubular flow, with surface ligands monitored by flow cytometry, with fluorescently labeled soluble ligands or monoclonal antibodies against specific adhesive domains on receptors or ligands. Aggregation was quantitated by monitoring the change in particle concentration with time by particle counting, and expressed as Capture efficiencies (CE) = Experimental/calculated initial rates of aggregation. The contributions of adhesive domains on putative ligands or receptors mediating aggregation at any given flow condition were evaluated with monoclonal antibodies or peptides known to block these adhesive sites. Surprisingly, ristocetin, which "chemically activates" GPIb/vWF to mediate spontaneous binding of the ligand to its receptor, at low concentrations yielding <2000 platelet-bound vWF monomers, gave efficient aggregation even at 1000 sec(-1) (CE = 0.34 +/- 0.02, n = 11) with only GPIb required. The physiologic activators ADP and thrombin both supported efficient aggregation of washed platelets with no exogenous ligands at 1000 sec(-1) by surface-secreted vWF (CE = 0.08 +/- 0.01, n = 6), in contrast to poorer ADP and soluble Fg-mediated aggregation in the absence of secretion (CE = 0.05). The secreted, platelet-bound, vWF-mediated aggregation completely depends on GPIIb-IIIa but partially and increasingly requires GPIb with increasing shear. Molecular models for these interactions are presented in terms of "rolling" and "firm" capture. Flow conditions will be critically important in designing and selecting anti-thrombotic drugs directed against the appropriate adhesive domains on receptors and ligands, which likely include other members such as thrombospondin and P-selectin.

The in vitro and in vivo pharmacological profiles of a platelet glycoprotein IIb/IIIa antagonist, NSL-9403

The in vitro and in vivo pharmacological profiles of NSL-9403 [orotyl-serylarginyl-glycyl-asparatyl-tryptophane], a platelet glycoprotein IIb/IIIa (GpIIb/IIIa) antagonist, has been studied. NSL-9403 inhibited platelet aggregation of human platelet-rich plasma (PRP) with IC50 values of 4.3 +/- 0.4 microM (collagen) and 1.8 +/- 0.3 microM (ADP), which was about 100 times more potent than RGDS. It also inhibited the binding of fibrinogen to activated platelets. Ex vivo collagen and ADP-induced platelet aggregation in a guinea pig was inhibited after a bolus intravenous administration of NSL-9403 at 1.25 mg/kg and above. NSL-9403 had an anti-thrombotic effect in in vivo thrombosis models. In a platelet agonist-induced pulmonary embolic sudden death model, where a bolus injection of collagen and epinephrine induced sudden death in mice, intravenous administration of NSL-9403 before an injection of collagen and epinephrine inhibited this platelet-agonist induced death in a dose dependent manner. In an arterio-venous shunt, infusion of NSL-9403 at 3 mg/kg/hour prevented an increase in circulation pressure due to thrombus formation in the shunt circuit and platelet loss. Infusion of NSL-9403 at 1 to 10 mg/kg/hour produced a complete inhibition of platelet-dependent arterial thrombosis in a dog femoral arterial thrombosis model. Thus NSL-9403 is a potent inhibitor or platelet aggregation in vitro and a potent anti-thrombotic agent in vivo with a relatively short duration of action.

Classes of hydration sites at protein-water interfaces: the source of contrast in magnetic resonance imaging

Immobilized protein solute, approximately 20 wt %, alters the longitudinal and transverse nuclear magnetic relaxation rates 1/T1 and 1/T2 of solvent water protons in a manner that makes their values indistinguishable from those of a typical human tissue. There is now a quantitative theory at the molecular level (S.H. Koenig and R. D. Brown III (1993) Magn. Reson. Med. 30:685-695) that accounts for this, as a function of magnetic field strength, in terms of several distinguishable classes of water-binding sites at the protein-water interface at which significant relaxation and solute-solvent transfer of proton Zeeman energy occur. We review the arguments that these several classes of sites, characterized by widely disparate values of the resident lifetimes tau M of the bound waters, are associated with different numbers of hydrogen bonds that stabilize the particular protein-water complex. The sites that dominate relaxation-and produce contrast in magnetic resonance imaging (MRI), which derives from 1/T1 and 1/T2 of tissue water protons-have tau M approximately 10(-6)s. These, which involve four hydrogen bonds, occupy < or = 1% of the protein-water interface. Sites that involve three bonds, although more numerous, have < or = 20% smaller intrinsic effect on relaxation. The greater part of the "traditional" hydration monolayer, with even shorter-lived hydrogen-bonded waters, has little influence on solvent relaxation and is relatively unimportant in MRI. Finally, we argue, from the data, that most of the protein of tissue (a typical tissue is mostly protein) must be rotationally immobile (with Brownian rotational relaxation times slower than that of a 5 x 10(7) Da (very heavy) globular protein). We propose a functional basis for this immobilization ("cytoplasmic order"), and then indicate a way in which this order can break down ("cytoplasmic chaos") as a result of neoplastic transformation (cancer) and alter water-proton rates of pathological tissue and, hence, image contrast in MRI.

Dynamics of platelet glycoprotein IIb-IIIa receptor expression and fibrinogen binding. II. Quantal activation parallels platelet capture in stir-associated microaggregation

There is broad agreement that platelet aggregation is generally dependent on fibrinogen (Fg) binding to the glycoprotein (GP) IIb-IIIa receptor expressed on the activated platelet surface. We therefore compared rates and extents of aggregation and of fibrinogen receptor expression and specific Fg binding to activated platelets, as a function of ADP concentration. Human citrated platelet-rich plasma (diluted 10-fold) was stirred with adenosine diphosphate (ADP) for 10 s or 2 min to measure rates and extent of aggregation, respectively, determined from the decrease in the total number of particles. The number of fibrinogen receptors and bound Fg were measured from mean fluorescence values obtained with FITC-labeled IgM monoclonal antibody PAC1 and the IgG monoclonal antibody, 9F9, respectively, using flow cytometry as presented in part I (Frojmovic et al., 1994). Because flow cytometric and aggregation measurements were routinely determined at room temperature and 37 degrees C, respectively, we also compared and found temperature-independent initial rates of aggregation. The fraction of platelets with fluorescence values above one critical threshold value, corresponding to maximally "activated" platelets (P*), increased with increasing activator concentration and correlated linearly with the fraction of platelets recruited into aggregates for ADP (r > 0.9). Aggregation was not rate-limited by fibrinogen receptor expression or by Fg binding. It appears that each platelet expresses its maximal Fg receptors at a critical ADP concentration, i.e., occupancy of ADP receptors. This, in turn, leads to rapid Fg occupancy and capture of such "quantally activated" platelets into aggregates.