Dynamic oscillation measurements of starch networks at temperatures above 100 degrees C

Effect of dry heat and its combination with vacuum heat on physicochemical, rheological and release characteristics of Alocasia macrorrhizos retrograded starches

Retrograded starches have received increasing attention due to their potential excipient properties in pharmaceutical formulations. However, to evade its application-oriented challenges, modification of retrograded starch is required. The study emphasizes influence of dry heating and the dual heat treatment by dry heating amalgamation with the vacuum heat treatment on quality parameters of retrograded starch. The starch was isolated by using two different extraction media (0.05 % w/v NaOH and 0.03 % citric acid) from Alocasia macrorrhizos and then retrograded separately. Further, retrograded starches were first modified by dry heating and afterwards modified with combination of dry and vacuum heating. Modification decreased moisture, ash content and increased solubility. Modified Samples from NaOH media had higher water holding capacity and amylose content. X-ray diffraction revealed type A and B crystals with increasing crystallinity of retrograded heat-modified samples from NaOH media. Thermogravimetric analysis, differential scanning calorimetry confirmed thermal stability. Shear tests showed shear-thinning behavior whereas dominant storage modulus (G/) over loss modulus (G//), depicting gel-like behavior. Storage, loss, and complex viscosity initially increased, then decreased with temperature. In-vitro release reflects, modified retrograded starches offers versatile drug release profiles, from controlled to rapid. Tailoring starch properties enables precise drug delivery, enhancing pharmaceutical formulation flexibility and efficacy.

Rheology of carbohydrate blends close to the glass transition: Temperature and water content dependence of the viscosity in relation to fragility and strength

Several modifications of the Williams-Landel-Ferry (WLF) equation that incorporate the water-content dependence of the viscosity are introduced and applied to the fitting the zero-shear viscosity of a systematic series of maltopolymer-maltose blends for water contents w between 4% and 70% (M. Dupas-Langlet et al., Carbohydrate Polymers 213 (2019) 147-158). These models include a previously published model that addresses the water-content dependence of the viscosity via a Gordon-Taylor-type modification of the C₂ coefficient of the WLF equation. New models that are based on two simple assumptions are introduced: 1. The viscosity at the glass transition temperature T_g decreases exponentially with the water content and 2. The WLF coefficient C₂ depends linearly on the water content. The modified WLF models allow to extract the so-called isoviscosity lines, that connect points of varying temperature and water content that are characterized by the same viscosity. Based on data obtained between T = -15 °C and 70 °C using shear rheology (w = 30-70% w/w) and dynamic mechanical thermal analysis (w = 4-9% w/w), we conclude that the models provide a good fit of the experimental data, and that additional data, specifically very close to the glass transition line, is needed, to assess the hypotheses underlying the various modified WLF models. It is established that the viscosity at T_g is dependent on the composition and decreases with the content of maltose and water. The modified WLF models are used to determine Angell's fragility parameter m and Roos' strength parameter S. m and S are observed to increase, respectively decrease with increasing water and maltose content, signifying an increasing temperature dependence of the viscosity close to T_g with decreasing diluent content. The application of the isoviscosity concept to unit operations in the food and pharmaceutical industry is discussed. Specifically, we show how to analyze atomization, agglomeration, sintering and compaction using the isoviscosity concept.

Rheological and Structural Properties of Camel Milk/Sweet Potato Starch Gel

The unique composition of camel milk limited its use for fermented products preparation. In this research, camel milk (CAM) or cow milk (COM) was blended with sweet potato starch (SPS). Blends were precooked and the rheological properties of the gel were determined. Since the elastic modulus (G′) was much greater than the viscous modulus (G″), milk + SPS gels are considered viscoelastic. The tan δ of all blends was <1.0, signifying solid-like behavior; however, variations between CAM gels or COM were identified. Unlike COM, CAM was more frequency-dependent at low frequencies (0.1 to 1.0 rad/sec). Gels exhibited shear thinning according to the nonlinear rheological tests. Camel milk exhibited gel hardness much higher than cow milk. Because of the domination of G′ and the low power law exponent, camel milk is expected to present processing complications such as in extrusion cooking.

Effects of Defatted Flaxseed Addition on Rheological Properties of Wheat Flour Slurry

Rheological property of defatted flaxseed-added wheat flour dispersions was investigated as a function of defatted flaxseed concentration (0–20%), NaCl concentration (0, 0.6, and 1.2%), sucrose concentration (0, 5, and 10%), and slurry concentration (33and 62.5%). Frequency sweep tests at 20°C and temperature sweep tests from 20 to 90°C were applied to the samples. The experimental measurements demonstrated that the viscoelastic moduli of samples increased with the increase in defatted flaxseed concentration from 0 to 20% and decreased with the increase in NaCl, sucrose, and water concentration at 20°C. The gelatinization temperatures of the defatted flaxseed-wheat slurry samples were delayed with the addition of defatted flaxseed, NaCl, and sucrose but hastened with the addition of water.