Effects of linear flow velocity and residence time on the retention of non-polar aqueous organic analytes by cartridges of tenax-gc

Trace determination of 1-octacosanol in rat plasma by solid-phase extraction with Tenax GC and capillary gas chromatography

1-Octacosanol is the major component of policosanol, a new natural lowering-cholesterol agent. A sensitive solid-phase extraction with a Tenax GC capillary gas chromatography method for determining the proportion of this fatty alcohol in plasma after its denaturation with trichloroacetic acid was developed. The trimethylsilyl ether derivative of the target analyte obtained from the organic extract showed excellent chromatographic properties and was detectable in the low nanogram range (1 ng/ml). Adequate separation from plasma's extract was achieved with a fused-silica capillary column (30m x 0.25 mm I.D.) with SPB-5 (0.5 microm film thickness) and operated with temperature programming from 100 to 200 degrees C at 40 degrees C/min and from 200 degrees C increased at 10 degrees C/min to 320 degrees C, then held for 30 min, the carrier gas flow-rate (argon) was 1 ml/min. Quantification was performed by the internal standard method using 1-hexacosanol. The reliable relative retention parameters and the mass response factors values, and their confidence levels, ensure a proper GC sensitivity, necessary for the determination of the alcohol being analyzed. The method was evaluated to a concentration range from 6 to 47.6 ng/ml of plasma obtaining recoveries from 95 to 98%. The correlation between the theoretical concentration values and the corresponding experimental values was appropriate (gamma=0.9718 x -0.0915; r2=0.9998). The method showed a good within-day (RSD=4.3%) and between-day (RSD=6.0%) precision according to the acceptance criteria (<10%). This procedure was successfully applied to the study of 1-octacosanol in rat plasma samples after a single oral administration (40 mg/kg) of policosanol.

Fifty years of solid-phase extraction in water analysis--historical development and overview

The use of an appropriate sample handling technique is a must in an analysis of organic micropollutants in water. The efforts to use a solid phase for the recovery of analytes from a water matrix prior to their detection have a long history. Since the first experimental trials using activated carbon filters that were performed 50 years ago, solid-phase extraction (SPE) has become an established sample preparation technique. The initial experimental applications of SPE resulted in widespread use of this technique in current water analysis and also to adoption of SPE into standardized analytical methods. During the decades of its evolution, chromatographers became aware of the advantages of SPE and, despite many innovations that appeared in the last decade, new SPE developments are still expected in the future. A brief overview of 50 years of the history of the use of SPE in organic trace analysis of water is given in presented paper.

Uptake rates of semipermeable membrane devices (SPMDs) for PCDDs, PCDFs and PCBs in water and sediment

Uptake rates of several PCDDs, PCDFs and PCBs were measured for semipermeable membrane devices (SPMDs) under controlled conditions in bulk water and sediment. The study was performed at 19 degrees C and 11 degrees C, and water and sediment concentrations were measured during the exposure. Linear uptake rates for specific PCDD/Fs and PCBs in 19 degrees C water varied from 34 to 111 l/m2 day and in 11 degrees C water from 8.8 to 96 l/m2 day for the whole SPMD. Uptake rates at 19 degrees C sediment ranged from 9.0 to 80 mgOC/m2 day and in 11 degrees C sediment, from 3.0 to 31, mgOC/m2 day. Partitioning of the compounds between membrane and lipid was also measured during the linear uptake phase. The membrane-lipid concentration ratios ranged from 0.02 to 1.11 depending on the compound, temperature, and bulk medium.

Determination of kinetic and retention properties of cartridge and disk devices for solid-phase extraction

The kinetic properties of cartridge and disk solid-phase extraction devices are determined by forced-flow liquid chromatography. Typical cartridges provide about 5-15 theoretical plates per cm of bed height and particle-loaded membranes provide about 4-9 theoretical plates for a 0.5-mm-thick membrane. It is shown that cartridge devices fail to provide their maximum trapping performance because of inadequate packing density and that the required packing density could be easily achieved in practice with particles of a standard size. The retention properties of common sorbents for extraction from water and air are characterized with the solvation parameter model. For predominantly aqueous solutions a favorable cavity term results in increased retention while polar interactions tend to reduce retention. Retention on porous polymer sorbents is more complicated because of their capacity to absorb significant amounts of the sample processing solvent resulting in solvent-dependent changes in retention properties. For trapping organic volatiles from air cavity formation and dispersion interactions are important, and in the case of Tenax its capacity for induction interactions is also significant.