Determination of rotenone in river water utilizing packed capillary column switching liquid chromatography with UV and time-of-flight mass spectrometric detection

Predicting the Potential for Natural Recovery of Atlantic Salmon (Salmo salar L.) Populations following the Introduction of Gyrodactylus salaris Malmberg, 1957 (Monogenea)

Gyrodactylus salaris (Monogenea, Platyhelminthes) is a notifiable freshwater pathogen responsible for causing catastrophic damage to wild Atlantic salmon stocks, most notably in Norway. In some strains of Baltic salmon (e.g., from the river Neva) however, the impact is greatly reduced due to some form of innate resistance that regulates parasite numbers, resulting in fewer host mortalities. Gyrodactylus salaris is known from 17 European states; its status in a further 35 states remains unknown; the UK, the Republic of Ireland and certain watersheds in Finland are free of the parasite. Thus, the parasite poses a serious threat if it emerges in Atlantic salmon rearing regions throughout Europe. At present, infections are generally controlled via extreme measures such as the treatment of entire river catchments with the biocide rotenone, in order to remove all hosts, before restocking with the original genetic stock. The use of rotenone in this way in EU countries is unlikely as it would be in contravention of the Water Framework Directive. Not only are such treatments economically and environmentally costly, they also eradicate the potential for any host/parasite evolutionary process to occur. Based on previous studies, UK salmon stocks have been shown to be highly susceptible to infection, analogous to Norwegian stocks. The present study investigates the impact of a G. salaris outbreak within a naïve salmon population in order to determine long-term consequences of infection and the likelihood of coexistence. Simulation of the salmon/ G. salaris system was carried out via a deterministic mathematical modelling approach to examine the dynamics of host-pathogen interactions. Results indicated that in order for highly susceptible Atlantic strains to evolve a resistance, both a moderate-strong deceleratingly costly trade-off on birth rate and a lower overall cost of the immune response are required. The present study provides insights into the potential long term impact of G. salaris if introduced into G. salaris-free territories and suggests that in the absence of external controls salmon populations are likely to recover to high densities nearing 90% of that observed pre-infection.

Comparison of Fenton and sono-Fenton bisphenol A degradation

Degradation of bisphenol A (BPA) was carried out with the Fenton reagent with and without additional sonochemical treatment. The Fenton and the sono-Fenton decomposition of BPA showed that ultrasound irradiation of wastewater improved the wet oxidation process of 25 mg l(-1) BPA solutions. The sonochemical degradation of BPA was monitored using UV absorption and large volume injection packed capillary LC measurements.

Time of flight mass spectrometry applied to the liquid chromatographic analysis of pesticides in water and food

Liquid chromatography coupled to mass spectrometry (LC-MS) is an excellent technique to determine trace levels of polar and thermolabile pesticides and their degradation products in complex matrices. LC-MS can be equipped with several mass analyzers, each of which provides unique features capable to identify, quantify, and resolve ambiguities by selecting appropriate ionization and acquisition parameters. We discuss in this review the use of LC coupled to (quadrupole) time-of-flight mass spectrometry (LC-(Q)ToF-MS) to determine the presence of target and non-target pesticides in water and food. This technique is characterized by operating at a resolving power of 10,000 or more. Therefore, it gives accurate masses for both parent and fragment ions and enables the measurement of the elemental formula of a compound achieving compound identification. In addition, the combination of quadrupole-ToF permits tandem mass spectrometry, provides more structural information, and enhances selectivity. The purpose of this article is to provide an overview on the state of art and applicability of liquid chromatography time-of-flight mass spectrometry (LC-ToF-MS), and liquid chromatography quadrupole time-of-flight mass spectrometry (LC-QToF-MS) for the analysis of pesticides in environmental matrices and food. The performance of such techniques is depicted in terms of accurate mass measurement, fragmentation, and selectivity. The final section is devoted to describing the applicability of LC-(Q)ToF-MS to routine analysis of pesticides in food matrices, indicating those operational conditions and criteria used to screen, quantify, and identify target and "suspected" pesticides and their degradation products in water, fruits, and vegetables. The potential and future trends as well as limitations of LC-(Q)ToF-MS for pesticide monitoring are highlighted.

Extraction of rotenone from Derris elliptica and Derris malaccensis by pressurized liquid extraction compared with maceration

The extraction of active compounds from plants is one of the most critical steps in the commercial development of natural products for medicinal, herbicidal or pesticidal use. The focus of this study was to compare conventional maceration and pressurized liquid extraction (PLE) techniques for the efficient extraction of rotenone from the stem and root of Derris elliptica Benth and Derris malaccensis Prain. The effects of experimental variables, such as solvent, temperature and pressure, on PLE efficiency have been studied. Chloroform was determined to be a good extraction solvent (rotenone content 40.6%, w/w) compared to commonly used solvent, 95% ethanol (rotenone content 15.0%, w/w). The optimal conditions for PLE were 50 degrees C and 2000 psi. PLE showed higher extraction efficiency (rotenone content 46.1%, w/w) as compared with conventional maceration method (rotenone content 40.6%, w/w). The order of rotenone content found in crude extract obtained by optimized method from the highest to the lowest was root (46.1%, w/w) and stem (9.4%, w/w) of D. elliptica and stem of D. malaccensis (5.2%, w/w), respectively. Moreover, the results from this study indicated that PLE was considerably less time and solvent consuming (30 min, 3 ml/g of dried sample) than the conventional maceration techniques (72 h, 10 ml/g of dried sample).

Comparison of advanced oxidation processes and identification of monuron photodegradation products in aqueous solution

The photodegradation of monuron (3-(4-chlorophenyl)-1,1-dimethylurea) in aqueous solutions under simulated solar irradiation has been conducted by different advanced oxidation processes (UV/H(2)O(2), UV/H(2)O(2)/Fe(2+), UV/H(2)O(2)/TiO(2), UV/TiO(2), dark H(2)O(2)/Fe(3+)). The degradation rates were always higher for the homogeneous catalysis in photo-Fenton reactions (UV/H(2)O(2)/Fe(2+)) compared to the heterogeneous photocatalytic systems (TiO(2)/UV and UV/H(2)O(2)/TiO(2)). Optimal concentrations of Fe(2+) and H(2)O(2) for the abatement of the herbicide in the photo-Fenton system were found to be 1 mM Fe(II) and 10 mM H(2)O(2). Several intermediary products were identified using large volume injection micro-liquid chromatography with UV detection (mu-LC-UV), mu-LC-MS and GC-MS techniques and a degradation mechanism has been proposed.

Potential of liquid chromatography/time-of-flight mass spectrometry for the determination of pesticides and transformation products in water

Until now, time-of-flight (TOF) mass analysers have only been very rarely used in pesticide residue analysis (PRA) of water samples. However, the inherent characteristics of TOF MS make these analysers well-suited to this field, mainly for qualitative purposes. Thus, the high sensitivity obtained from full-scan acquisition in comparison to other MS analysers and the high resolution of TOF MS suggest its suitability for screening purposes; it also increases the multiresidue capabilities of methods based on it and decreases the chance of recording false positives. Although these characteristics can also be helpful for quantification, confirmation and elucidation, some limitations on the use of TOF for these purposes have been observed. These limitations are more noticeable when dealing with samples containing very low analyte concentrations, which is the normal situation for PRA in water. The use of hybrid quadrupole-time-of-flight instruments (QTOF) minimises the limitations of TOF, facilitating the simultaneous detection and unequivocal confirmation of pesticides found in the sample. Additionally, the acquisition of accurate product ion full-scan mass spectra can help to elucidate the structures of unknown compounds. In this paper, the potential of TOF and QTOF hyphenated to liquid chromatography for PRA in water is explored, emphasizing both the advantages and limitations of this approach for screening, quantification, confirmation and elucidation purposes. Emphasis is placed on the determination of polar pesticides and transformation products-the analytes that fit well with LC-API-(Q)TOF MS technology.

A comparison of performance of various analytical columns in pharmaceutical analysis: conventional C18 and high throughput C18 Zorbax columns

New improved types of analytical columns Zorbax Eclipse XDB-C18 (75 mm x 4.6 mm i.d., 3.5 microm) and Zorbax Eclipse XDB-C18 (50 mm x 4.6 mm i.d., 1.8 microm) have been tested for determination of estradiol (active substance), methylparaben, propylparaben (preservatives) and estrone (degradation product) and compared with the conventional C18 columns (250 mm x 3.0 mm i.d., 5.0 microm). The Zorbax columns differ with their particle size, column length and ODS (octadecylsilica) type as well. Higher flow-rates (up to about 2.5 ml min(-1)) could be applied regardless to back-pressure. The analysis - previously done at 40 degrees C - could be performed even at ambient temperature. Analytical run was shortened to 3.5 min (from 12 min used for the conventional C18 column) with the same or better retention characteristics. System suitability data for all Zorbax columns show the advantages of these columns for the practical use in routine quality control of pharmaceuticals, particularly from the point of view of speed of analysis and solvent consumption.

Determination of bradykinin and arg-bradykinin in rat muscle tissue by microdialysis and capillary column-switching liquid chromatography with mass spectrometric detection

Quantification of bradykinin peptides in limited amounts of rat muscle tissue dialysate has been performed using a packed capillary LC-ESI-TOF-MS method. The micro dialysate samples (450 microL) with added internal standard were loaded onto a 1 mm x 5 mm loading column packed with 5 microm Kromasil C18 particles by a carrier solution of 0.1% formic acid in ACN/water (5:95, v/v) at a flow rate of 250 microL/min for online preconcentration of the analytes. Back-flushed elution onto a 150 mm x 0.5 mm Zorbax C18 column packed with 5 microm particles was conducted using a linear solvent ACN/H2O gradient containing 0.1% formic acid. (Tyr8)-bradykinin was used as an internal standard and was added to the dialysis sample prior to injection. Baseline separation of bradykinin, arg-bradykinin and (tyr8)-bradykinin was achieved within 10 min. Positive ESI was performed in the m/z range of 200-1300. The method was validated in the range 0.2-1.0 ng/mL dialysate, yielding correlation coefficients of 0.995 and 0.990 for bradykinin and arg-bradykinin, respectively. The within-assay and between-assay precisions were between 4.3-9.6% and 6.2-10.6%, respectively. Both arg-bradykinin and bradykinin were detected in dialysate from rat muscle tissue, at concentrations of 0.1 and 0.4 ng/mL for bradykinin and arg-bradykinin, respectively, confirming the presence of arg-bradykinin in rat muscles.

Combined solid-phase extraction and 2D LC–MS for characterization of the neuropeptides in rat-brain tissue

A comprehensive two-dimensional capillary liquid chromatographic (2D LC) method has been established for determination of neuropeptides in rat brain tissue. Rats were exposed to different levels of stress before sacrificing and the aim of this study was to design a powerful separation and detection technique capable of characterizing differences between cerebral neuropeptide expression as a function of stress level. Rat brain samples were homogenized and subjected to clean-up by solid-phase extraction (SPE) on both a reversed-phase (C(18)) and a weak cation-exchange (CBA) cartridge. The samples were divided in two fractions (A and B) depending on retention on the CBA column. Subsequently, 50 microL of the sample were injected on to a strong cation exchanger (SCX) at a mobile phase pH of 3, which enabled preconcentration of positively charged compounds. The trapped compounds were eluted using step gradients of ammonium formate in water-ACN (90:10, v/v). Before enrichment in the second dimension, the eluate from the first dimension was diluted with water containing 0.1% TFA. The compounds eluting from the first dimension were trapped in the second dimension using a dual precolumn system consisting of two short capillary columns packed with Kromasil C(18), 10 microm particles. Subsequently, the trapped compounds were backflushed on to a 10 cm long, 320 microm I.D. analytical column packed with Kromasil C(18) 3.5 microm particles, on which they were efficiently separated. Detection was performed using an ion-trap mass spectrometer (ITMS) in both the MS and the MS-MS mode. Comparison of base-peak chromatograms (BPC) from MS analysis of stressed and non-stressed rats clearly revealed several differences in neuropeptide expression. The MS-MS data obtained combined with Mascot software were employed for peptide identification.

Assay of rotenone in river water by high-throughput tandem mass spectrometry and multiple-reaction monitoring methodology

The high-throughput analytical approach proposed for the assay of rotenone in lake and river waters presented here is based on atmospheric pressure chemical ionization (APCI) multiple-reaction monitoring (MRM) methodology whereby the analyte and internal standard solutions are directly analyzed, without any previous chromatographic separation. The very good accuracy is obtained by the critical choice of a reference compound that shows gas-phase chemistry similar to that of the analyte, by producing the same product ions selected for the MRM-based assay.

High-throughput assay of rotenone in olive oil using atmospheric pressure chemical ionization tandem mass spectrometry

A high-throughput method is presented for the determination of rotenone in contaminated matrices. The procedure involves atmospheric pressure chemical ionization tandem mass spectrometry with a triple-quadrupole instrument and the use as internal standard of a cycloadduct derivative of rotenone itself. The method was applied to the evaluation of the decay of rotenone in olives and olive oil at various times after exposure to the contaminant.

Controlling the retention in capillary LC with solvents, temperature, and electric fields

Once a suitable stationary phase and column dimensions have been selected, the retention in liquid chromatography (LC) is traditionally adjusted by controlling the mobile phase composition. Solvent gradients enable achievement of good separation selectivity while decreasing the separation time as compared to isocratic elution. Capillary columns allow use of other programming parameters, i.e. temperature and applied electric fields, in addition to solvent gradient elution. This paper presents a review of programmed separation techniques in miniaturized LC, including retention modeling and method transfer from the conventional to micro- and capillary scales. The impact of miniaturized instrumentation on retention and the limitations of capillary LC are discussed. Special attention is focused on the gradient dwell volume effects, which are more important in micro-LC techniques than in conventional analytical LC and may cause significant increase in the time of analysis, unless special instrumentation and (or) pre-column flow-splitting is used. The influence of temperature upon retention is also discussed, and applications where the temperature has been actively used for retention control in capillary LC are included together with the instrumentation utilized. Finally the possibilities of additional selectivity control by applying an electric field over a packed capillary LC column are discussed.

High resolution electrospray and electrospray tandem mass spectra of rotenone and its isoxazoline cycloadducts

An evaluation of the gas-phase ion chemistry of rotenone (1) by electrospray ionisation (ESI) mass spectrometry (MS) and tandem mass spectrometry (MS2) is presented, aiming at providing tools for its determination in natural and biological matrices. The behaviour of its cycloadducts with benzonitrile-N-oxide (2) and 2,4,6-trimethylbenzonitrile-N-oxide (3) was also evaluated and the MS data thus obtained have provided evidence into the mechanism of formation of the key product ion at m/z 192 which can be considered a marker in the MS and MS2 spectra of rotenone and its derivatives.

Environmental and food applications of LC-tandem mass spectrometry in pesticide-residue analysis: an overview

An overview is given on pesticide-residue determination in environmental and food samples by liquid chromatography/mass spectrometry/mass spectrometry (LC/MS/MS). Pesticides comprise a large number of substances that belong to many completely different chemical groups, the only common characteristic is that they are effective against pests. They still constitute a challenge in MS because there is no collective pathway for fragmentation. A brief introduction to the theory of tandem MS permits a discussion of which parameters influence the ionization efficiency when the ions are subjected to different actions. Emphasis is placed on the different tandem MS instruments: triple and ion-trap quadrupoles, and hybrid quadrupole time-of-flight (Q-TOF), including advantages and drawbacks, typical detection limits, and ion signals at low concentrations. The instrumental setup, as well as LC and mass spectrometric experimental conditions, must be carefully selected to increase the performance of the analytical system. The capacity of each instrument to provide useful data for the identification of pesticides, and the possibility to obtain structural information for the identification of target and non-target compounds, are discussed. Finally, sample preparation techniques and examples of applications are debated to reveal the potential of the current state-of-the-art technology, and to further promote the usefulness of tandem MS.