Migration behavior and selectivity of sulfonamides in capillary electrophoresis

On-line preconcentration and determination of sulfadiazine in food samples using surface molecularly imprinted polymer coating by capillary electrophoresis

In this study, on-line preconcentration and selective determination of the trace sulfadiazine (SDZ) existing in milk and hen egg white samples were realized by the capillary electrophoresis using molecularly imprinted polymer (MIP) coated capillary. The capillary coated with MIP was firstly prepared through the surface imprinted techniques, using SDZ as template molecule and dopamine as function monomer and crosslinker, and then amine-terminated poly(2-methyl-2-oxazoline) (PMOXA-NH₂) was introduced onto polydopamine layer to reduce the non-specific adsorption. Successful preparation of SDZ-MIP-PMOXA coating was verified by zeta potential, as well as water contact angle. The SDZ-MIP-PMOXA coated capillary performed well on-line preconcentration of SDZ and the obtained peak area of SDZ was 46 times higher than that one obtained in bare capillary using the same procedure. Then the proposed on-line preconcentration method was fully validated and displayed good linear behavior in the concentration from 5.0 to 100.0 ng/mL, with the limit of detection was low to 1.5 ng/mL; and this method presented excellent accuracy and robustness. The prepared SDZ-MIP-PMOXA coated capillary also showed high selectivity with the imprinting factor of 5.85 and good repeatability during five consecutive runs with the relative standard deviation value of peak area was 1.6%. At last, the application of the prepared SDZ-MIP-PMOXA coated capillary in the detection of SDZ in spiked food samples was investigated, and good recoveries of 98.7-109.3% were obtained.

A kinetic study of the photolysis of sulfamethoxazole with special emphasis on the photoisomer

Abstract

The previously not studied photochemical degradation of sulfamethoxazole (SMX) to the isomer of SMX (ISO) was measured via a polychromatic (Xe) and a monochromatic (Hg) light source and accompanied by quantum chemical DFT calculations. In addition to the $$\mathrm{p}K_\mathrm{a} = \;7.0 \pm 0.1$$ p K a = 7.0 ± 0.1 of ISO, tautomer-dependent properties such as the $$K_\mathrm{OW}$$ K OW were measured and theoretically confirmed by DFT. The kinetics in solutions below and above the $$\mathrm{p}K_\mathrm{a} = 5.6$$ p K a = 5.6 of SMX were studied for the available and quantifiable products SMX, ISO, 3-amino-5-methylisoxazole (AMI), 2-amino-5-methyloxazole (AMO), and sulfanilic acid (SUA). The quantum yields of the neutral ($$\Phi _\mathrm{N}$$ Φ N ) and anionic $$\Phi _\mathrm{A}$$ Φ A ) forms of SMX ($$\Phi _\mathrm{A} = 0.03 \pm 0.001$$ Φ A = 0.03 ± 0.001 , $$\Phi _\mathrm{N} = 0.15 \pm 0.01$$ Φ N = 0.15 ± 0.01 ) and ISO ($$\Phi _\mathrm{A} = 0.05 \pm 0.01$$ Φ A = 0.05 ± 0.01 and $$\Phi _\mathrm{N} = 0.06 \pm 0.02$$ Φ N = 0.06 ± 0.02 ) were found to be wavelength-independent. In a competitive reaction to the formation of ISO from SMX, the degradation product TP271 is formed. Various proposed structures for TP271 described in the literature have been studied quantum mechanically and can be excluded for thermodynamic reasons. In real samples in a northern German surface water in summer 2021 mean concentrations of SMX were found in the range of 120 ng/L. In agreement with the pH-dependent yields, concentrations of ISO were low in the range of 8 ng/L.

Graphical abstract

Enhanced transformation of aquatic organic compounds by long-lived photooxidants (LLPO) produced from dissolved organic matter

Dissolved organic matter (DOM) plays a crucial role in the photochemical transformation of organic contaminants in natural aquatic systems. The present study focuses on the characterization of a specific effect previously observed for electron-rich phenols, consisting in an acceleration of the DOM-photosensitized transformation of target compounds at low concentrations (< 1 µM). This effect was hypothesized to be caused by DOM-derived "long-lived" photooxidants (LLPO). Pseudo-first-order rate constants for the transformation of several phenols, anilines, sulfonamide antibiotics and phenylureas photosensitized by Suwannee River fulvic acid were determined under steady-state irradiation using the UVA and visible wavelengths from a medium-pressure mercury lamp. A significant enhancement (by a factor of 2.4 - 16) of the first-order transformation rate constant of various electron-rich target compounds was observed for an initial concentration of 0.1 μM compared to 5 μM . This effect points to a relevant reactivity of these compounds with LLPO. For phenols and anilines the enhancement effect occurred only above certain standard one-electron oxidation potentials. From these data series the standard one-electron reduction potential of LLPO was estimated to be in the range of 1.0 - 1.3 V versus the standard hydrogen electrode. LLPO are proposed to mainly consist of phenoxyl radicals formed by photooxidation of electron-poor phenolic moieties of the DOM. The plausibility of this hypothesis was successfully tested by studying the photosensitized transformation kinetics of 3,4-dimethoxyphenol in aqueous solutions containing a model photosensitizer (2-acetonaphthone) and a model electron-poor phenol (4-cyanophenol) as DOM surrogates.

Determination of acidity constants, ionic mobilities, and hydrodynamic radii of carborane-based inhibitors of carbonic anhydrases by capillary electrophoresis

Capillary electrophoresis (CE) has been applied for determination of the thermodynamic acidity constants (pK_a ) of the sulfamidoalkyl and sulfonamidoalkyl groups, the actual and limiting ionic mobilities and hydrodynamic radii of important compounds, eight carborane-based inhibitors of carbonic anhydrases, which are potential new anticancer drugs. Two types of carboranes were investigated, (i) icosahedral cobalt bis(dicarbollide)(1-) ion with sulfamidoalkyl moieties, and (ii) 7,8-nido-dicarbaundecaborate with sulfonamidoalkyl side chains. First, the mixed acidity constants, pK_a ^mix , of the sulfamidoalkyl and sulfonamidoalkyl groups of the above carboranes and their actual ionic mobilities were determined by nonlinear regression analysis of the pH dependences of their effective electrophoretic mobility measured by capillary electrophoresis in the pH range 8.00-12.25, at constant ionic strength (25 mM), and constant temperature (25°C). Second, the pK_a ^mix were recalculated to the thermodynamic pK_a s using the Debye-Hückel theory. The sulfamidoalkyl and sulfonamidoalkyl groups were found to be very weakly acidic with the pK_a s in the range 10.78-11.45 depending on the type of carborane cluster and on the position and length of the alkyl chain on the carborane scaffold. These pK_a s were in a good agreement with the pK_a s (10.67-11.27) obtained by new program AnglerFish (freeware at https://echmet.natur.cuni.cz), which provides thermodynamic pK_a s and limiting ionic mobilities directly from the raw CE data. The absolute values of the limiting ionic mobilities of univalent and divalent carborane anions were in the range 18.3-27.8 TU (Tiselius unit, 1 × 10^-9 m² /Vs), and 36.4-45.9 TU, respectively. The Stokes hydrodynamic radii of univalent and divalent carborane anions varied in the range 0.34-0.52 and 0.42-0.52 nm, respectively.

Experimental and theoretical study of kinetic and mechanism of hydroxyl radical-mediated degradation of sulfamethazine

Hydroxyl radical (^•OH)-based advanced oxidation technologies (AOTs) is an effective and clean way to remove sulfonamide antibiotics in water at ambient temperature and pressure. In this study, we systematically investigated the degradation kinetics of sulfamethazine (SMT) by ^•OH with a combination of experimental and theoretical approaches. The second-order rate constant (k) of SMT with ^•OH was experimentally determined to be 5.27 ± 0.06 × 10⁹ M^-1 s^-1 at pH 4.5. We also calculated the thermodynamic and kinetic behaviors for the reactions by density functional theory (DFT) using the B3LYP/6-31G*. The results revealed that ^•OH addition pathways at the methylene (C4) site on the pyridine ring and the ortho sites (C12 and C14) of the amino group on the benzene ring dominate the reaction, especially C14 site on the benzene ring accounted for 43.95% of SMT degradation kinetics. The theoretical k value which was calculated by conventional transition state theory is 3.96 × 10⁹ M^-1 s^-1, indicating that experimental observation (5.27 ± 0.06 × 10⁹) is correct. These results could further help AOTs design in treating sulfonamide during wastewater treatment processes.

Degradation of emerging contaminants by sono-Fenton process with in situ generated H2O2 and the improvement by P25-mediated visible light irradiation

Developing advanced treatment methods to minimize the release of emerging contaminants to natural water has become a matter of considerable interest. Sono-Fenton process was investigated to degrade bisphenol A (BPA) and sulfadiazine (SDZ). The H₂O₂ generated in situ was used as the exclusive source. Results showed that, the 400 kHz ultrasound is more efficient in creating homogeneous sono-Fenton than the 20 kHz apparatus due to the higher production of OH. Influence of Fe²⁺ was more remarkable on the degradation of hydrophilic SDZ, and its degradation kinetics was well fitted by two-stage kinetic model. However, the Fe²⁺ and H₂O₂ were unproductively wasted, which could not be improved by changing the dosing modes of Fe²⁺. The presence of P25 under visible light irradiation could significantly accelerate SDZ degradation at small amount of iron precursors, mainly via promoting the Fe²⁺/Fe³⁺ cycling by the photoelectrons. Moreover, SDZ degradation in sono-Fenton process was significantly inhibited at pH > 7, but the inhibition was very weak in P25-assisted sono-Fenton process. The presence of P25 also improved the mineralization. Three primary degradation pathways of SDZ degradation were proposed, including the attacking of the benzene ring, the oxidation of the amino group and the extrusion of SO₂.

Modelled phototransformation kinetics of the antibiotic sulfadiazine in organic matter-rich lakes

Xenobiotic compounds are commonly detected in inland waters. Sunlight-induced photochemical reactions contribute to xenobiotic degradation, but the role of different photoreactions on large geographic scales remains poorly understood. Here, we used a combination of photochemical modelling and large-scale field data from 1020 lakes across Sweden to elucidate the photodegradation kinetics of the commonly used antibiotic sulfadiazine (SDZ) in organic matter-rich lakes. SDZ occurs in two forms, namely acidic HSDZ (pK_a = 6.5) and basic/deprotonated SDZ^-. Both species are oxidised fast by the photogenerated triplet states of natural organic matter (³NOM*). However, they also undergo efficient back reactions because the partially oxidised HSDZ (and SDZ^- to a larger extent) can be reduced back to the initial compounds by the phenolic moieties contained in NOM. Typical lakes in Sweden are rich in NOM and have low pH, with the consequence that SDZ photochemistry would be dominated by HSDZ. Our simulation results showed that SDZ photodegradation kinetics in Swedish lakes would become significantly slower with increasing water depth and pH, while it depended little on latitude, which affects irradiance, or on organic matter content. As a consequence, SDZ would be particularly persistent in lakewater in some densely populated areas with relatively deep and high-pH lakes such as, most notably, the Stockholm region. Here the surface waters could be more heavily contaminated by pharmaceuticals compared to the scarcely populated regions in the centre-north of the country, where lakewater could otherwise promote an efficient photodegradation of SDZ.

Bioavailability of Antibiotics at Soil-Water Interfaces: A Comparison of Measured Activities and Equilibrium Partitioning Estimates

There are growing concerns that antibiotic pollution impacts environmental microbiota and facilitates the propagation of antibiotic resistance. However, the prediction or analytical determination of bioavailable concentrations of antibiotics in soil is still subject to great uncertainty. Biological assays are increasingly recognized as valuable complementary tools that allow a more direct determination of the residual antibiotic activity. This study assessed the bioavailability of structurally diverse antibiotics at a soil-water interface applying activity-based analyses in conjunction with equilibrium partitioning (EqP) modeling. The activity against Gram-positive and Gram-negative bacteria of nine antibiotics from different classes was determined in the presence and absence of standard soil (LUFA St. 2.2). The addition of soil affected the activity of different antibiotics to highly varying degrees. Moreover, a highly significant correlation ( p < 0.0001) between the experimentally observed and the EqP-derived log EC₅₀ (half-maximal effective concentration) values was observed. The innovative experimental design of this study provided new insights on the bioavailability of antibiotics at soil-water interfaces. EqP appears to be applicable to a broad range of antibiotics for the purpose of screening-level risk assessment. However, EqP estimates cannot replace soil-specific ecotoxicity testing in higher-tier assessments, since their accuracy is still compromised by a number of factors.

Effects of the antioxidant moieties of dissolved organic matter on triplet-sensitized phototransformation processes: Implications for the photochemical modeling of sulfadiazine

Previous studies have shown that the photodegradation of some pollutants, induced by the excited triplet states of chromophoric dissolved organic matter (³CDOM*), can be inhibited by back-reduction processes carried out by phenolic antioxidants occurring in dissolved organic matter (DOM). Here, for the first time to our knowledge, we included such an inhibition effect into a photochemical model and applied the model predictions to sulfadiazine (SDZ), a sulfonamide antibiotic that occurs in surface waters in two forms, neutral HSDZ and anionic SDZ^- (pK_a = 6.5). The input parameters of the photochemical model were obtained by means of dedicated experiments, which showed that the inhibition effect was more marked for SDZ^- than for HSDZ. Compared to the behavior of 2,4,6-trimethylphenol, which does not undergo antioxidant inhibition when irradiated in natural water samples, the back-reduction effect on the degradation of SDZ was proportional to the electron-donating capacity of the DOM. According to the model results, direct photolysis and OH reaction would account for the majority of both HSDZ and SDZ^- photodegradation in waters having low dissolved organic carbon (DOC < 1 mgC L^-1). With higher DOC values (>3-4 mgC L^-1) and despite the back-reduction processes, the ³CDOM* reactions are expected to account for the majority of HSDZ phototransformation. In the case of SDZ^- at high DOC, most of the photodegradation would be accounted for by direct photolysis. The relative importance of the triplet-sensitized phototransformation of both SDZ^- and (most importantly) HSDZ is expected to increase with increasing DOC, even in the presence of back reduction. An increase in water pH, favoring the occurrence of SDZ^- with respect to HSDZ, would enhance direct photolysis at the expense of triplet sensitization. SDZ should be fairly photolabile under summertime sunlight, with predicted half-lives ranging from a few days to a couple of months depending on water conditions.

Elucidating ozonation mechanisms of organic micropollutants based on DFT calculations: Taking sulfamethoxazole as a case

Ozonation is widely used in wastewater treatment plants to remove diverse organic micropollutants. As molecular structures of organic micropollutants contain multiple ozone-preferred reaction sites, and moreover intermediate products can react with ozone again, ozonation mechanism is complex. A fast increasing number of organic micropollutants and a great demand of ecological risk assessments call for an in silico method to provide insights into the ozonation mechanism of organic micropollutants. Here, an in silico model was developed to unveil ozonation mechanisms of organic micropollutants. Sulfamethoxazole was taken as a case. The model enumerates elementary reactions following well-accepted ozonation patterns and secondary transformation reactions established for intermediates by experiments. Density functional theory (DFT) calculations were employed for evaluating thermodynamic feasibilities of reaction pathways. By calculating Gibbs free energies, ozonation products of SMX were predicted. The predicted products are consistent with those detected in experiments. This method is advanced in revealing all possible reaction pathways including minor pathways that produce toxic byproducts but are difficult to be observed by experiments. Accordingly, water treatment engineers can setup necessary treatment technology to ensure water safety.

Oral pharmacokinetics of the acidic drugs, diclofenac and sulfamonomethoxine in male Shiba goats

In the present study, we examined the oral pharmacokinetics of the acidic drugs, diclofenac (DF) and sulfamonomethoxine (SMM), which have different physicochemical properties, in Shiba goats. DF and SMM were intravenously and orally administered to 5 male goats using a crossover design. The T_max of DF and SMM were reached 1.5 and 5.6 hr after they have been orally administered, respectively, and this was followed by their slow elimination. The elimination of both drugs was markedly faster after being intravenously rather than orally administered, which indicated flip-flop phenomena after the oral administration. The mean absorption times (MATs) of DF and SMM were 6 and 15 hr, respectively. This slow absorption may have been due to slow gastric emptying in goats. The large difference observed in MATs between DF and SMM may have been because DF, which is more lipophilic than SMM, was partly absorbed from the forestomach. Therefore, these results suggest that the absorption of highly lipophilic drugs from the forestomach may be markedly high in Shiba goats. In case of drugs whose elimination is quite fast, their efficacies may appear from the early stage after oral administration even in ruminants, because elimination rate is the determinant factor of T_max in flip-flop phenomena. Such drugs may be used orally even in ruminants.

Sorption of selected veterinary antibiotics onto dairy farming soils of contrasting nature

The sorption potential for three sulfonamides (SAs), sulfamethoxazole (SMO), sulfachloropyridazine (SCP) and sulfamethazine (SM) and a macrolide, tylosin tartrate (TT) was assessed on six New Zealand dairy farming soils of contrasting physico-chemical properties. Kinetics studies showed that the sorption was rapid in the first few hours of the contact time (0-2h for SA and 0-4h for TT) and thereafter apparent equilibrium was achieved. Batch sorption isotherm data revealed that the degree of isotherm linearity (N) for SCP and SM varied between 0.50 and 1.08 in the six soils. Isotherms of both TT and SMO were mostly non-linear with the degree of non-linearity for TT (N=0.38-0.71) being greater than for SMO (0.42-0.75) in all soils except Manawatu (TT) and Te Kowhai (SMO) where a linear pattern was observed. Concentration-dependent effective distribution coefficient (Kd(eff)) values for the SMO, SCP and SM antibiotics in the soils ranged from 0.85 to 16.35 L kg(-1), while that for TT was 1.6 to 1,042 L kg(-1). The sorption affinity for all soils followed an order: TT>SCP>SM>SMO. Remarkable high sorption for tylosin in Matawhero soil as compared to other soils was attributed to the presence of oxygen containing acidic polar functional groups as evident in the FT-IR spectra of the soil. Furthermore, it was hypothesised that sorption of TT onto soils was mostly driven by metal oxide-surface mediated transformations whereas for sulfonamides it was primarily due to hydrophobic interactions.

Transformation kinetics of biochemically active compounds in low-pressure UV photolysis and UV/H(2)O(2) advanced oxidation processes

Factors controlling photolysis and UV/H2O2 photooxidation rates of the biochemically active compounds (BACs) sulfamethoxazole, sulfamethazine, sulfadiazine, trimethoprim, bisphenol A, and diclofenac were determined. Experiments were conducted with a quasi-collimated beam apparatus equipped with low-pressure UV lamps. The effects of pH, H2O2 concentration, and background water matrix (ultrapure water, lake water, wastewater treatment plant effluent) on BAC transformation rates were evaluated. For the sulfa drugs, solution pH affected direct photolysis rates but had little effect on the hydroxyl radical oxidation rate. For sulfamethoxazole, the neutral form photolyzed more easily than the anionic form while the reverse was the case for sulfamethazine and sulfadiazine. For trimethoprim, the hydroxyl radical oxidation rate was higher for the cationic form (pH 3.6) than for the neutral form (pH 7.85). Quantum yields and second order rate constants describing the reaction between the hydroxyl radical and BACs were determined and used together with background water quality data to predict fluence-based BAC transformation rate constants (k'). For both the lake water and wastewater treatment plant effluent matrices, predicted k' values were generally in good agreement with experimentally determined k' values. At typical UV/H2O2 treatment conditions (fluence=540 mJ cm(-2), H2O2 dose=6 mg L(-1)), BAC transformation percentages in North Carolina lake water ranged from 43% for trimethoprim to 98% for diclofenac. In wastewater treatment plant effluent, BAC transformation percentages were lower (31-97%) at the same treatment conditions because the hydroxyl radical scavenging rate was higher.

Extraction mechanism of sulfamethoxazole in water samples using aqueous two-phase systems of poly(propylene glycol) and salt

Based on the poly(propylene glycol)(400) (PPG(400))-salt aqueous two-phase system (ATPS), a green, economical and effective sample pretreatment technique coupled with high performance liquid chromatography was proposed for the separation and determination of sulfamethoxazole (SMX). The extraction yield of SMX in PPG(400)-salt ATPS is influenced by various factors, including the salt species, the amount of salt, pH, and the temperature. Under the optimum conditions, most of SMX was partitioning into the polymer-rich phase with the average extraction efficiency of 99.2%, which may be attributed to the hydrophobic interaction and salting-out effect. This extraction technique has been successfully applied to the analysis of SMX in real water samples with the recoveries of 96.0-100.6%, the detection limits of 0.1 μg L(-1), and the linear ranges of 2.5-250.0 μg L(-1).

Sulfamethoxazole abatement by means of ozonation

Sulfamethoxazole (SMX) is a bacteriostatic antibiotic largely used for diverse types of illness. Its widely use in humans and even in animals releases unmetabolized and active metabolites that have a strong potential in terms of effect in organisms. In this work, 200 mg L(-1) solution of sulfamethoxazole was treated by ozonation at different pH. Results showed that ozonation was proved to be an efficient method to degrade sulfamethoxazole. After 15 min of ozonation (corresponding dose=0.4 g of ozone L(-1)), the complete antibiotic abatement was almost achieved with just 10% of mineralization. The biodegradability and toxicity of the ozonation intermediates were also studied. A biodegradability enhancement (increment of BOD(5)/COD ratio) from 0 to 0.28 was observed after 60 min of ozonation. The acute toxicity of the intermediates was followed by the Microtox test and the toxicity profile showed a slight acute toxicity increment in the first stage of ozonation. The pH variation had an important role in the TOC and COD removal, promoting their growth with the increment of alkalinity. The second order kinetic constants for the ozonation of the SMX in an order of magnitude of 10(5) L mol(-1)s(-1) were also determined for pH 5 and 7.

Determination of sulfonamides in milk after precolumn derivatisation by micellar liquid chromatography

A simple method to identify and determine six sulfonamides (sodium sulfacetamide, sulfamethizole, sulfaguanidine, sulfamerazine, sulfathiazole and sulfamethoxazole) in milk by micellar liquid chromatography (MLC) is reported. The assay makes use of a precolumn diazotisation-coupling derivatisation including the formation of an azo dye that can be detected at 490 nm. Furthermore, the use of MLC as an analytical tool allows the direct injection of non-purified samples. The separation was performed with an 80 mM SDS-8.5% propanol eluent at pH 7. Analysis times are below 16 min with a complete resolution. Linearities (r>0.9999), as well as intra- and inter-day precision (below 2.7%), were studied in the validation of the method. The limits of detection and quantification ranged from approximately 0.72 to 0.94 and 2.4 to 3.1 ng mL(-1), respectively. The detection limit was below the maximum residue limit established by the European Community. Finally, recoveries in spiked milk samples were in the 83-103% range.

Comparison of migration models for acidic solutes in micellar electrokinetic chromatography

The validity of two models that explain the migration of ionisable solutes in micellar electrokinetic chromatography (MEKC), mobility model and retention factor model, has been tested. For this purpose, the mobility (mu) and retention factor (k) of a set of 10 phenolic compounds with different hydrophobicity and pKa values have been determined for several sodium dodecyl sulphate (SDS) concentrations and pH values, and fitted to the models. Results show that in general the retention factor model explains better the retention of ionisable solutes, although for hydrophilic compounds at low SDS concentration, mobility model can give better fits. The different drawbacks pointed out by several authors in relation to both models have been checked, and a deep evaluation of each one has been done. As a result we have observed that, while in the retention factor model the variation of k with pH and [SDS] always follows the same trend, the variation of mu with these variables mainly depends on the value of the binding constant of the neutral form of the solutes to the micelles, KHA(m), which plays a critical role in the fit of the mobility model. Also we provide rules and advices to set up the experimental conditions to apply each model to a particular solute.

Application of capillary zone electrophoresis with large-volume sample stacking to the sensitive determination of sulfonamides in meat and ground water

A CZE method with UV-Vis detection has been established and validated for the determination of nine sulfonamides: sulfapyridine, sulfamethazine, sulfamerazine, sulfamether, sulfadiazine, sulfadimethoxine, sulfamethoxazole, sulfachlorpyridazine, and sulfamethizole. Optimum separation was obtained on a 64.5 cm x 75 microm bubble cell capillary using a buffer containing 45 mM sodium phosphate and 10% methanol at pH 7.3, with temperature and voltage of 27 degrees C and 25 kV, respectively. p-Aminobenzoic acid was used as an internal standard . Taking into account the lack of sensitivity of the UV-Vis detection, the application of an on-line preconcentration methodology, such as large-volume sample stacking with polarity switching has been proposed. This procedure combined with a solvent extraction/SPE method applied for off-line preconcentration and cleanup provides a significant improvement in the LODs, ranging from 2.59 to 22.95 mug/L for the studied compounds; the quantification of these residues being possible below the levels established by EU legislation in animal food products, such as meat. Satisfactory recoveries were also obtained in the analysis of these compounds in ground water.

Determination of caffeine and its metabolites in urine by capillary electrophoresis-mass spectrometry

The caffeine content of foods and beverages varies considerably, interfering with our ability to obtain valid interpretations in many human studies with regard to the mechanism of action(s) of caffeine and/or its metabolites. The rate of metabolism of caffeine and other xanthine drugs also varies greatly from one individual to another. Therefore, it is extremely important to develop accurate, reliable analytical methods to quantify caffeine and its metabolites in simple and complex matrixes. A simple method is described for the separation and characterization of caffeine and its major metabolites employing capillary electrophoresis (CE) coupled to ultraviolet-absorption and mass spectrometry (MS) detection. After optimization of the electrophoresis separation conditions, a reliable separation of caffeine and 11 of its major metabolites was achieved in 50 mM ammonium carbonate buffer, pH 11.0. The volatile aqueous electrolyte system used with a normal electroosmotic flow polarity also provided an optimal separation condition for the characterization of the analytes by MS. The CE method achieved baseline resolution for all 12 compounds in less than 30 min. The CE-MS method is suitable for use as a routine procedure for the rapid separation and characterization of caffeine and its metabolites. The usefulness of this method was demonstrated by the extraction, separation, and identification of caffeine and its 11 metabolites from normal urine samples. The urine specimens were first acidified to obtain optimum binding efficiency to the sorbents of the off-line, solid-phase extraction procedure employed here, and an acidified eluent solvent was employed for the desorption step to maximize the recovery of the bound analytes.

Potentiometric determination of acid dissociation constants (pKa) for human and veterinary antibiotics

This work determined the acid dissociation constants (pKa) of 26 common human and veterinary antibiotics by potentiometric titration. Selected antibiotics consisted of sulfonamides, macrolides, tetracyclines, fluoroquinolones, and other miscellaneous antibiotics. After validation of analysis methods using phosphoric acid as a model compound, a second-derivative (delta2pH/deltaV2) method was primarily applied to determining pKa's from titration curves for most antibiotics due to its convenience and accuracy. For tetracyclines, however, a least-square non-linear regression method was developed to determine their pKa's because the second-derivative method cannot well distinguish the pKa,2 and pKa,3 of tetracyclines. Results indicate that the pKa values are approximately 2 and 5-7.5 for sulfonamides; 7.5-9 for macrolides; 3-4, 7-8 and 9-10 for tetracyclines; 3-4, 6, 7.5-9 and 10-11 for fluoroquinolones; while compound-specific for other miscellaneous antibiotics. The moieties corresponding to specific pKa's were identified based on chemical structures of antibiotics. In addition, the pKa's available in literature determined by various techniques are compiled in comparison with the values of this work. These results are expected to essentially facilitate the research on occurrence, fate and effects, analysis methods development, and control of antibiotics in various treatment operations.

A quantitative structure property relationship study of electrophoretic mobility of analytes in capillary zone electrophoresis

A quantitative structure property relationship (QSPR) is proposed to calculate the electrophoretic mobility of analytes in capillary zone electrophoresis. The proposed model employs logarithm of the electrophoretic mobility (ln micro) as dependent variable and partial charge (PQ), surface area (V(2/3)), total energy (TE), heat of formation (DeltaH(f)) and molecular refractivity (MR) as independent variables whose calculated using AM1 (Austin model 1) semi-empirical quantum mechanics method by HyperChem 7.0 software. The general form of the model is: ln micro =K(0)+K(1)PQ+K(2)V(2/3)+K(3)TE+K(4)DeltaH(f)+K(5)MR, where K(0)-K(5) are the model constants computed using a least-square method. The applicability of the model on real mobility data has been studied employing five experimental data sets of beta-blockers, benzoate derivatives, non-steroidal anti-inflammatory drugs, sulfonamides and amines in different buffers. The accuracy of the model is assessed using absolute average relative deviation (AARD) and the overall AARD value. The obtained AARD for the sets studied are 1.0 (N=10), 2.1 (N=26), 0.8 (N=11), 0.6 (N=13) and 2.7% (N=18), respectively, and the overall AARD is 1.4%. The model is cross-validated using one leave out technique and the obtained overall AARD is 1.8%. To further investigate on the applicability of the proposed model, the prediction capability of the model is evaluated by employing a minimum number of six experimental data points as training set, and predicting the mobility of other data points using trained models. The obtained overall AARD (for 48 predicted data points) is 5.6%.

Prediction of electrophoretic mobilities of sulfonamides in capillary zone electrophoresis using artificial neural networks

Artificial neural networks (ANNs) were successfully developed for the modeling and prediction of electrophoretic mobility of a series of sulfonamides in capillary zone electrophoresis. The cross-validation method was used to evaluate the prediction ability of the generated networks. The mobility of sulfonamides as positively charged species at low pH and negatively charged species at high pH was investigated. The results obtained using neural networks were compared with the experimental values as well as with those obtained using the multiple linear regression (MLR) technique. Comparison of the results shows the superiority of the neural network models over the regression models.

Capillary-electrochromatographic separations with copolymeric reversed-stationary phase and ion-exchanger-packed columns

A macroporous, spherical, 7 microm, polystyrene-divinylbenzene (PS-DVB), reversed-phase adsorbent (PRP-1) was evaluated as a stationary phase for the capillary electrochromatographic (CEC) separation of neutral, acidic, and basic analytes of pharmaceutical interest. Electroosmotic flow (EOF) for a PRP-1 packed capillary is nearly constant over the pH 2 to 10 range and is higher than for a silica-based C18 packed capillary on the acidic side. EOF increases with an increase in buffer acetonitrile concentration or as applied potential increases. As analyte hydrophobicity increases, analyte retention and migration time increases. Increasing buffer acetonitrile concentration reduces analyte partitioning with the PS-DVB stationary phase and analyte retention and migration time decreases. When exchange sites are present on the PS-DVB copolymer, EOF (EOF is reversed for the anion-exchanger) increases as the exchange capacity increases. An increased exchange capacity also reduces partitioning of the analyte with the PS-DVB matrix and analyte retention and migration time decrease. Because of excellent stability in an acid environment, the PRP-1 packed capillary can be used in strong acid buffer solution and weak acid and base analytes depending on pKa values can be separated as neutral species and cations, respectively. CEC separations on a PRP-1 capillary of neutral steroids, weak base pharmaceuticals (separation as cations), purines and pyrimidines (as cations), fatty acids (as undissociated species), and sulfa derivatives (as cations) are described. Efficiency for the PRP-1 packed capillary for acetone or thiourea as the analyte is about 6 x 10(4) plates m(-1).

Applications of a sulfonated-polymer wall-modified open-tubular fused-silica capillary in capillary zone electrophoretic separations

A fused-silica capillary that is wall-modified via chemically bonding a sulfonated polymer to the capillary wall has a uniform negative charge density on its surface and produces an electroosmotic flow (EOF) greater than 4 x 10(-4) cm2 V(-1) s(-1) The EOF is nearly independent of buffer pH over the pH range of 2 to 10 and is lower than the EOF obtained for the bare fused-silica capillary at the more basic pH but is higher at the more acidic buffer pH. Optimization of buffer pH can be based on analyte pKa values to improve the overall quality of the capillary zone electrophoresis (CZE) separation of complex mixtures of weak acid and base analytes. Because of the high EOF in an acidic buffer, the capillary is useful for the separation of weak organic bases which are in their cation forms in the acidic buffer. EOF for the sulfonic acid bonded phase capillary can be adjusted via buffer additives such as organic solvent, tetraalkylammonium salts, multivalent cations and alkylsulfonic acids. The advantages of utilizing buffer pH and the EOF buffer modifiers to enhance migration time, selectivity, and resolution in CZE separations with this capillary are illustrated using a series of test analyte mixtures of inorganic anions, carboxylic acids, alkylsulfonic acids, benzenesulfonic acids, sulfas, pyridines, anilines or small-chain peptides.

Capillary electrophoresis separation of vinpocetine and related compounds: prediction of electrophoretic mobilities in partly aqueous media

Offord's equation, a relationship between electrophoretic mobility and charge, size and shape of peptides, has been extended to quantitate the electrophoretic mobility of vinca alkaloids. Partly aqueous protonation constants and the derived theoretical mobilities have been proven to be able to predict experimental electrophoretic mobilities. In practice, seven vincamine derivatives of very low water-solubility were separated by capillary electrophoresis. Buffer total concentration, apparent pH and methanol content, the three most important parameters of the running buffer, were used in triangular resolution mapping to characterize separation. Even though electrophoresis is well known to slow down in partly aqueous media, under our optimized circumstances a baseline separation was achieved within 8 min in each case.

Migration behavior and separation of benzenediamines, aminophenols and benzenediols by capillary zone electrophoresis

The migration behavior and separation of five benzendiamines, five aminophenols and three benzenediols were investigated in capillary zone electrophoresis. The results indicate that benzendiamines and aminophenols are optimally separated with a phosphate buffer at pH 5, whereas benzenediol isomers are best separated at pH about 12. The addition of surfactant monomers of tetradecyltrimethylammonium bromide to a phosphate buffer at pH 5 under the conditions of reversed electroosmotic flow is effective for separating these dye intermediates, except for the separation of 1,2-benzenediol from 1,3-benzenediol. The addition of sodium tetraborate as an electrolyte modifier is effective in the separation of 1,2-benzenediol from 1,3-benzenediol, but the latter comigrates with the 1,4-benzenediol isomer at pH 5.0. The electrophoretic mobility of ionized analytes can be described with Offord's equation, and the migration order depends on their ratios of charge to mass. In addition, the pKa values of these analytes in 50 mM phosphate buffer are reported.