Determination and speciation of metals by liquid chromatography

Quantifying indium with ion chromatography in hydro- and biohydrometallurgical leaching solutions

A methodology has been developed to chromatographically quantify indium in polymetallic (bio)hydrometallurgical processing solutions using the Dionex IonPac CS5A column and pyridine-2,6-dicarboxylic acid eluent. Cu(II) and In(III) could be separated by elevating the column temperature to 45°C. The comparatively low stability constant of the In-eluent complex (log K₂  = 3.8) required typical leaching samples to be diluted in the eluent rather than acid or water to overcome ligand competition between components of the sample solution and the eluent. The methodology was applied to leachates from (bio)hydrometallurgical processing of oxidic flue dust residues and sulfidic zinc ores, where both are promising candidates for the recovery of indium from low grade ores and metallurgical wastes. Indium, ferrous iron, ferric iron, copper, zinc, nickel, and manganese concentrations could be simultaneously quantified. The method was found suitable for samples containing at least 0.25 mg/L indium and an iron to indium ratio of up to 100:1.

Chromium and its speciation in water samples by HPLC/ICP-MS--technique establishing metrological traceability: a review since 2000

Chromium holds a special position among living organisms because depending on its species it can be either essential or toxic. Cr(VI) even at very low concentrations is harmful and carcinogenic, while Cr(III) is a necessary microelement for cellular metabolism. Therefore, a simple analysis of Cr concentration in collected samples will not be able to distinguish these differences effectively: for a proper chemical analysis we need to perform a reliable detection and quantification of Cr species. Separation and detection of chromium can be accomplished with high performance liquid chromatography hyphenated to inductively coupled plasma mass spectrometry (HPLC/ICP-MS) in a one-step. Our review assembles articles published since 2000 regarding chromium speciation in water samples with the use of HPLC/ICP-MS. It addresses the following issues: chromium chemistry, the possibilities of dealing with interferences, metrological aspects, analytical performance and speciated isotope dilution mass spectrometry (SIDMS) which is a definitive measurement method. The authors would like to advocate this hyphenated advanced technique as well as the metrological approach in speciation analysis of chromium.

Determination of trace transition metals in environmental matrices by chelation ion chromatography

Trace transition metals (Fe(3+), Mn, Cu, Cd, Co, Zn, Ni) in environmental samples were analyzed by chelation ion chromatography using a mixed bed ion-exchange column with pyridine-2,6-dicarboxylic acid (PDCA) and oxalic acid as eluent and large volume direct injection (1,000 μl). The two eluents, PDCA and oxalic acid, were tested, and repeatability and detection limits were compared. The total analysis time was ~15 min. The separation with PDCA was more successful than that obtained with acid oxalic. It was observed that utilizing PDCA resulted in lower detection limits, higher repeatability, and a quantitative detection of Cd and Mn, which coelute as a single peak when using the oxalic acid. At last, the PDCA calibration graphs resulted linear (r (2) > 0.999) in the range 0.4-1,000 μg/L. The procedure was applied to the analysis of metals in soils and in water samples. The results obtained from the analysis of natural waters have demonstrated that the method is simple and efficient, therefore, can be used for the determination of metals in natural waters using a continuous and automatic monitoring system.

Determination of trace mercury species by high performance liquid chromatography-inductively coupled plasma mass spectrometry after cloud point extraction

A sensitive method for speciation analysis of inorganic mercury (Hg(2+)) and methyl mercury (MeHg(+)) has been developed by using high performance liquid chromatography (HPLC) combined with inductively coupled plasma mass spectrometry (ICP-MS) after cloud point extraction. The analytes were complexed with sodium diethyldithiocarbamate (DDTC) and preconcentrated by a non-ionic surfactant Triton X-114. Mercury species were effectively separated by HPLC in less than 6 min. The enhancement factors for 25 mL sample solution were 42 and 21, and the limits of detection were 4 and 10 ng L(-1) for Hg(2+) and MeHg(+), respectively. The developed method was successfully applied to the determination of trace amount of mercury species in environmental and biological samples.

Determination of selenium(IV) in pharmaceuticals and premixes by micellar liquid chromatography

A simple micellar liquid chromatographic technique for the determination of selenium(IV) in pharmaceutical products (multi-vitamin tablets, syrups) and animal premixes after pre-column derivatization with 2,3-diaminonaphthalene was developed and validated. Hypersil ODS column, 10% (v/v) 1-butanol in 0.05 M sodium dodecyl sulfate as the mobile phase and UV detection at 378 nm and were used. The retention time was about 8 min. In the course of the validation study, the specificity of the method was demonstrated. Linearity was established in the range 0.33-3.3 microg ml(-1) of selenium(IV) content. The limits of detection and quantitation were 0.1 and 0.3 microg ml(-1), respectively. The method showed excellent accuracy (100.04%). Precision (repeatability) gave a relative standard deviation less than 1%. The influence of the various method parameters (robustness study) was also investigated.

Identification and Characterization of Isomeric Intermediates in a Catalyst Formation Reaction by Means of Speciation Analysis Using HPLC−ICPMS and HPLC−ESI-MS

Information on chemical speciation is much needed in mechanistic and kinetic studies on catalyst formation processes in pharmaceutical research. Speciation analysis was applied to the identification and quantification of various rhodium species involved in a ligand exchange process leading to formation of catalyst dirhodium(II) tetrakis[methyl 2-oxopyrrolidin-5(S)-carboxylate]. Inductively coupled plasma mass spectrometry (ICPMS) was used as an element-specific detector following species separation by reversed-phase high-performance liquid chromatography (RP-HPLC), and electrospray ionization mass spectrometry (ESI-MS) was used for species identification and confirmation. A novel interface between the HPLC and ICPMS, which consisted of an eluent splitter, a desolvation unit, and the ICPMS built-in peristaltic pump, enabled the use of RP-HPLC with gradient elution and up to 100% organic components in the LC eluent without organic loading in the plasma. A variety of reaction intermediates were identified and quantified along the pathway to formation of the desired product, including isomeric di-, tri-, and tetrasubstituted species previously believed to be absent. This has provided new insights into the mechanism and kinetics of the reaction. The combination of HPLC-ICPMS and HPLC-ESI-MS has proven to be a valuable tool for the investigation of species evolution in catalyst formation process.

The determination of trace metal pollutants in environmental matrices using ion chromatography

A review is presented detailing the development of ion chromatography (IC) as a selective analytical tool for the determination of toxic metals and their organic species in many environmental sample matrices. A brief outline of ion chromatographic principles, together with an overview of the stationary phases used to separate metals, namely ion exchangers, modified ion pair sorbents and chelating ion exchangers, and the methods for detecting metal ions including hyphenation with spectroscopy and sample preparation schemes are also given, prior to a critical examination of developed methods for various metals including arsenic, chromium, cadmium, lead, mercury, beryllium, aluminium and uranium since 1990.

Retention of alkali, alkaline earth and transition metals on an itaconic acid cation-exchange column. Eluent pH, ionic strength and temperature effects upon selectivity

The unusual selectivity of a methylene succinic (itaconic) acid modified polymeric column was investigated for the separation of alkali, alkaline earth, transition and heavy metals employing non-chelating inorganic eluents. The retention of selected metal ions on the column was investigated with simple HNO3 eluents and eluents prepared from KNO3 and KCl salts of varying pH (adjusted using HNO3). From these studies both the effect of eluent ionic strength and pH upon retention was evaluated for the itaconic acid stationary phase. The results obtained showed that despite slow exchange kinetics causing poor efficiencies, acceptable baseline separations of selected alkaline earth and transitions could be obtained under optimum conditions (the baseline separation of Mg(II), Ca(II), Mn(II), Cd(II), Zn(II) and Co(II) was possible using a 15 mM KNO3-5 mM KCl eluent at pH 3.50 in under 25 min). The use of an simple ionic strength step gradient was shown that facilitated the addition of Pb(II) to the above group of metal ions. An investigation into the effect of temperature upon peak efficiency and retention showed increased column temperature could be used to improve the resolution of closely eluting metal ions such as Ca(II) and Sr(II) and Ca(II) and Mn(II).

Separation of chromium (III) and chromium (VI) by capillary electrophoresis using 2,6-pyridinedicarboxylic acid as a pre-column complexation agent

A simple method was developed for the simultaneous determination of Cr(III) and Cr(VI) by capillary zone electrophoresis (CZE), where Cr(III) was chelated with ligands to form anionic complexes. Nitrilotriacetic acid, N-2-hydroxyethylenediaminetriacetic acid, ethylenediaminetetraacetic acid, diethylenetriaminepentaacetic acid, and 2,6-pyridinedicarboxylic acid (PDCA) were investigated as Cr(III) complexing ligands. Of all the ligands studied, 2,6-PDCA with Cr(III) gave the largest UV response and high selectivity for Cr(III). In addition, the condition for pre-column derivatization, including pH, concentration ratio [Cr(III)/2,6-PDCA] and the stability of Cr(III) complexes were also examined. The separation of anionic forms of Cr(III) and Cr(VI) was achieved using co-CZE with UV detection at 185 nm. The electrolyte contained 30 mM phosphate, 0.5 mM tetradecyltrimethylammonium bromide, 0.1 mM 2,6-PDCA and 15% (v/v) acetonitrile at pH 6.4. The detection limits were 2 microM for Cr(III) and 3 microM for Cr(VI) and linear plots were obtained in a concentration range of 5-200 microM. The utility of the method was demonstrated for the determination of Cr(III) and Cr(VI) in contaminated soils.

Preconcentration of contaminants in water analysis

Among the environmental areas, in this review attention will be focused on water matrices and both on organic (e.g., pesticides, herbicides, phenols, polycyclic aromatic hydrocarbons), inorganic species and anion pollutants, since these kinds of substances include a wide number of compounds with different physical and chemical properties and different effects on human health. Analytical methods for control of quality of waters are required to be highly specific and possibly highly sensitive for the determination of even low amounts of pollutants. The main problems encountered during the analysis are the separation of matrix components from the pollutants of interest and the achievement of low detection limits. Therefore an overview on different materials and techniques available for sample concentration and/or matrix removal will be provided and discussed according to the chemical characteristics of the pollutant that has to be enriched.

Trace analysis of heavy metals in groundwater samples by ion chromatography with post-column reaction and ultraviolet-visible detection

Groundwaters originating from local and regional aquifers surrounding ash deposits produced by a coal-fired power plant were collected. These water samples were chemically analyzed for quantifying their heavy metal composition at trace levels. A highly sensitive analytical technique based on ion chromatography with a UV-Vis detector and under isocratic eluent flow-rate conditions was used. In order to quantify the major heavy metals (Pb, Cu, Cd, Co, Zn and Ni), three ionic separation column systems were evaluated: (1) a cationic column (HPIC-CS2, Dionex) tested with two eluents (10 mM oxalic acid-7.5 mM citric acid; and 40 mM D-tartaric acid-12 mM citric acid); (2) an anionic column (HPIC-AS4, Dionex) evaluated with 25 mM oxalic acid as eluent: and (3) a bifunctional ion-exchange column (Ionpac CS5, Dionex) which was also tested with two eluents (6 mM pyridine, 2,6-dicarboxylic acid; and 50 mM oxalic acid/95 mM lithium hydroxide). The lowest detection limits achieved with the Ionpac CS5 column and the 50 mM oxalic acid-95 mM lithium hydroxide eluent enabled the heavy metal analysis in groundwater samples to be reliably performed. Details of this comparative study, including the ion chromatography procedure selected and its application to heavy metal analysis of groundwater samples, are presented in this work.

Chromium occurrence in the environment and methods of its speciation

This article includes a survey of chromium (Cr) occurrence in different environmental compartments, its pathways in the environment and the cross-sectional presentation of Cr speciation methods against the background of Cr chemistry. The aim of the article is to demonstrate that knowledge of interconversion processes between different Cr forms is necessary to understand its behaviour and role in the environment, in addition to enabling reliable Cr speciation analysis to be performed. The current methods of Cr speciation are presented, characterized and their usefulness discussed. These must rely on superior separation and detection capabilities since Cr in environmental compartments is mostly at trace or ultra-trace level. The need for using unique techniques of sampling, storage, handling and separation for Cr speciation is documented.

Liquid chromatography: a tool for the analysis of metal species

An overview is presented of classic and more recent applications of liquid chromatography for the analysis of metal species. The different approaches involving ion-exchange, ion-pair, and chelation separation mechanisms are discussed as well as the new philosophy of simply removing interferents before specific detections of metal ions (alkali and alakaline earths, rare earths, heavy and transition metals). New more selective materials enabling difficult separations and studies on multimodal or hyphenated techniques for metal speciation (e.g. arsenic and chromium) are considered.

Chemical modification of analytes in speciation analysis by capillary electrophoresis, liquid chromatography and gas chromatography

Chemical modification of target analytes is widely used in modern analytical methods. This review focuses on the application of chemical modification techniques is the simultaneous analysis of metallic species by capillary electrophoresis, liquid chromatography and gas chromatography. Emphasis is placed on the procedures relating to analyses carried out by capillary electrophoresis. The development of this topic in the past five years is evaluated for liquid chromatography and gas chromatography. The advantages, performance and application in real samples are compared for the three techniques.