Developments in sample preparation and separation techniques for the determination of inorganic ions by ion chromatography and capillary electrophoresis

Green Aspects of Ion Chromatography versus Other Methods in the Analysis of Common Inorganic Ions

Due to the increasing environmental awareness of the public, green chemistry has become an important element of environmental protection. In laboratories around the world, millions of analyses of inorganic and organic anions and cations in water and wastewater samples, and solid and gaseous samples are performed daily. Unfortunately, these activities still generate large costs, including environmental costs, which are related to the scale of the studies, the use of toxic chemical reagents, the waste generated, and the energy consumed. The methods used so far for inorganic ion analysis, including classical methods, are increasingly being replaced by instrumental methods, primarily based on ion chromatography. This paper presents the most important advantages and limitations of ion chromatography, and compares them with the costs of classical analyses for the analytes and sample types. Both the financial and environmental costs associated with the determination of common inorganic ions, such as Cl−, NO2−, NO3−, and NH4+, in 1000 environmental samples, were compared using selected reference wet classical methods and ion chromatography. The advantages and limitations of ion chromatography that allow this separation technique to be classified as a green analytical chemistry method have been described herein.

Determination of ammonium and biogenic amines by ion chromatography. A review

The amount and type of chemical compounds found in food products and the environment, which are and should be controlled, is increasing. This is associated with toxicological knowledge, resulting regulations, rapid development of analytical methods and techniques, and sample preparation methods for analysis. These include, among others, ammonia derivatives such as ammonium, and amines, including biogenic amines. Their occurrence in the environment and food is related to their widespread use in many areas of life and their formation as a result of various physical and chemical changes. Analysts use various methods both classical and instrumental to theirs quantify in different matrices such as food, medicinal and environmental samples. Nevertheless, there is still a need for analytical methods with increased matrix-tolerance, selectivity, specificity, and higher sensitivity. While in the determination of ammonium, ion chromatography is a reference method. In the case of biogenic amines, its use for these purposes is not yet so common. However, given ion chromatography its advantages and rapid development, its importance can be expected to increase in the near future, especially at the expense of gas chromatography methods. This paper is a summary of the advantages and limitations of ion chromatography in this important analytical field and a literature review of the past 15 years.

Development of a background electrolyte for the determination of inorganic cations in high ionic strength samples by capillary electrophoresis with indirect UV-absorption detection

In this study, a background electrolyte capable to separate and quantify inorganic cations in high ionic strength samples by UV-absorption indirect detection was designed. In this regard, the four most abundant monovalent and divalent cations in earth crust (K⁺, Na⁺, Ca⁺², Mg⁺²) were selected as model compounds. A group of small carboxylic acids and, several toluidines and pyridines were evaluated as mild strength complexing agents and chromophoric probes, respectively. The optimized background electrolyte was composed of 200 mM 2,4,6-trimethylpyridine as the chromophoric probe, 250 mM lactic acid as the weak complexing agent and pH buffering reagent (adjusted to pH 4.5), and 5% v/v methanol as organic solvent modifier. Based on a minimum number of components, it provided outstanding separation performance in less than 4 min in a wide linear dynamic range (10 - 2500 µg·mL^-1). Performances were contrasted against a reference method based on conductometric detection. Furthermore, studies of separation efficiency and peak shape were carried out at different analyte concentrations in high electric conductivity solutions. The herein developed method demonstrated exceptional features in terms of limits of detection (~10 µg·mL^-1), resolution, speed of analysis, sensitivity and peak capacity in high electric conductivity samples. Moreover, the method was successfully applied to high ionic strength samples such as rock digest, sea water, soy sauce and isotonic drinks.

Nanomaterials for sample pretreatment prior to capillary electrophoretic analysis

Nanomaterials are, in analytical science, used for a broad range of purposes, covering the area of sample pretreatment as well as separation, detection and identification of target molecules.

Microchip electrophoresis with amperometric detection method for profiling cellular nitrosative stress markers

The overproduction of nitric oxide (NO) in cells results in nitrosative stress due to the generation of highly reactive species such as peroxynitrite and N2O3. These species disrupt the cellular redox processes through the oxidation, nitration, and nitrosylation of important biomolecules. Microchip electrophoresis (ME) is a fast separation method that can be used to profile cellular nitrosative stress through the separation of NO and nitrite from other redox-active intracellular components such as cellular antioxidants. This paper describes a ME method with electrochemical detection (ME-EC) for the separation of intracellular nitrosative stress markers in macrophage cells. The separation of nitrite, azide (interference), iodide (internal standard), tyrosine, glutathione, and hydrogen peroxide (neutral marker) was achieved in under 40 s using a run buffer consisting of 7.5 to 10 mM NaCl, 10 mM boric acid, and 2 mM TTAC at pH 10.3 to 10.7. Initially, NO production was monitored by the detection of nitrite (NO2(-)) in cell lysates. There was a 2.5- to 4-fold increase in NO2(-) production in lipopolysaccharide (LPS)-stimulated cells. The concentration of NO2(-) inside a single unstimulated macrophage cell was estimated to be 1.41 mM using the method of standard additions. ME-EC was then used for the direct detection of NO and glutathione in stimulated and native macrophage cell lysates. NO was identified in these studies based on its migration time and rapid degradation kinetics. The intracellular levels of glutathione in native and stimulated macrophages were also compared, and no significant difference was observed between the two conditions.

Bioanalytical profile of the L-arginine/nitric oxide pathway and its evaluation by capillary electrophoresis

This review briefly summarizes recent progress in fundamental understanding and analytical profiling of the L-arginine/nitric oxide (NO) pathway. It focuses on key analytical references of NO actions and the experimental acquisition of these references in vivo, with capillary electrophoresis (CE) and high-performance capillary electrophoresis (HPCE) comprising one of the most flexible and technologically promising analytical platform for comprehensive high-resolution profiling of NO-related metabolites. Another aim of this review is to express demands and bridge efforts of experimental biologists, medical professionals and chemical analysis-oriented scientists who strive to understand evolution and physiological roles of NO and to develop analytical methods for use in biology and medicine.

Recent advances of transient isotachophoresis-capillary electrophoresis in the analysis of small ions from high-conductivity matrices

Since its invasion into the field of small ion analysis, quantitation of trace ionic analytes has always been a challenging task for CE, especially when dealing with highly saline samples. This review summarizes the method's progress and significant developments in the area due to its combination with on-line preconcentration by transient ITP (tITP). Principles of tITP stacking in high-conductivity solutions and operational preconcentration modes are considered. The most important application areas covered in this review include the analysis of seawater and biological fluids (urine, serum, etc.). Examples cited in this review demonstrate that tITP-CE is now on a certain way of becoming a recognized technique when the determination of trace ionic species in loaded matrices is the aim.

Negatively charged sol-gel column with stable electroosmotic flow for online preconcentration of zwitterionic biomolecules in capillary electromigration separations

A negatively charged sol-gel coating was developed for on-line preconcentration of zwitterionic biomolecules in capillary electrophoresis (CE), using asparagine and myoglobin as representative zwitterionic bioanalytes. The sol-gel coating was created by using a solution containing three precursors: mercaptopropyltrimethoxysilane (MPTMS), tetramethoxysilane (TMOS), and n-octadecyltriethoxysilane (C18-TEOS). The resulting sol-gel coating contained chemically bonded mercaptopropyl functional groups that were further oxidized by hydrogen peroxide to the corresponding sulfonic acid moieties. Such a surface-bonded sol-gel coating can carry a negative charge over a wide range of pH due to the presence of deprotonated sulfonic acid groups. Under favorable pH conditions, the negatively charged sol-gel coating can facilitate the extraction of positively charged analytes from a zwitterionic sample through electrostatic interaction. This principle was employed to extract myoglobin and asparagine by passing aqueous samples of these zwitterionic analytes through a negatively charged sol-gel column. The extracted analytes were then desorbed and focused via local pH change and stacking. The local pH change was accomplished by passing a buffer solution with a pH above the solute p/ value, while a dynamic pH junction between the sample solution and the background electrolyte was utilized to facilitate solute focusing. The sorption/desorption phenomena could, perhaps, also be explained on the basis of ion-exchange and local pH junction effects. On-line preconcentration and analysis results obtained on sulfonated sol-gel columns were compared with those obtained on an uncoated fused silica capillary of identical dimensions using conventional sample injections. Using UV detection, the presented sample preconcentration technique provided a sensitivity enhancement factor (SEF) on the order of 3 x 10(3) for myoglobin, and 7 x 10(3) for asparagine.

Determination of traces of chloride and fluoride in H2SO4, H3PO4 and H3BO3 by in situ analyte distillation—ion chromatography

A simple dual vessel in situ analyte distillation (IAD) system has been developed for suppressed ion chromatographic determination of chloride and fluoride ions in complex matrices. In IAD system, water vapours generated from the outer vessel reacts with sulfuric acid generating heat, thus favouring the quantitative distillation of chloride and fluoride within 30 min on water bath temperature (approximately 80 degrees C). The distilled analytes, as their respective acids in water, were directly injected into an ion-chromatograph. This newly developed method has been applied for analysis of trace impurities in H2SO4, H3PO4 and H3BO3. The detection limits for chloride is 8, 80 and 70ppb (w/w) for H2SO4, H3PO4 and H3BO3, respectively. For fluoride the detection limits are 6 and 60 ppb (w/w) for H2SO4 and H3PO4, respectively. The recovery of spikes for both the analytes ranged between 87 and 100%.

Determination of Heavy Metal Ions by Capillary Electrophoresis with Contactless Conductivity Detection after Field-amplified Sample Injection

A method has been developed for determining of heavy metal ions by field-amplified sample injection capillary electrophoresis with contactless conductivity detection. The effects of the 2-N-morpholinoethanesulfonic acid/histidine (MES/His) concentration in the sample matrix, the injection time and organic additives on the enrichment factor were studied. The results showed that MES/His with a low concentration in the sample matrix, an increase of the injection time and the addition of acetonitrile improved the enrichment factor. Four heavy metal ions (Zn2+, Co2+, Cu2+ and Ni2+) were dissolved in deionized water, separated in a 10 mM MES/His running buffer at pH 4.9 and detected by contactless conductivity detection. The detection sensitivity was enhanced by about three orders of magnitude with respect to the non-stacking injection mode. The limits of detection were in the range from 5 nM (Zn2+) to 30 nM (Cu2+). The method has been used to determine heavy metal ions in tap water.

Ultrasound-assisted analyte extraction for the determination of sulfate and elemental sulfur in zinc sulfide by different liquid chromatography techniques

The speciation and determination of sulfate (SO4(2-)) and elemental sulfur (S degree) in zinc sulfide (ZnS) using ion-chromatography (IC) and reversed-phase liquid chromatography (RPLC) respectively is described. Three sample pretreatment approaches were employed with the aim of determining sulfate: (i) conventional water extraction of the analyte; (ii) solid-liquid aqueous extraction with an ultrasonic probe; and (iii) elimination of the zinc sulfide matrix via ion-exchange dissolution (IED). The separation of sulfate was carried out by an anion-exchange column (IonPac AS17), followed by suppressed conductivity detection. Elemental sulfur was extracted ultrasonically from the acid treated sample solution into chloroform and separated on a reversed phase HPLC column equipped with a diode array detector (DAD) at 264 nm. The achievable solid detection limits for sulfate and sulfur were 35 and 10 microg g(-1) respectively.

The determination of trace metal pollutants in environmental matrices using ion chromatography

A review is presented detailing the development of ion chromatography (IC) as a selective analytical tool for the determination of toxic metals and their organic species in many environmental sample matrices. A brief outline of ion chromatographic principles, together with an overview of the stationary phases used to separate metals, namely ion exchangers, modified ion pair sorbents and chelating ion exchangers, and the methods for detecting metal ions including hyphenation with spectroscopy and sample preparation schemes are also given, prior to a critical examination of developed methods for various metals including arsenic, chromium, cadmium, lead, mercury, beryllium, aluminium and uranium since 1990.

Separation and analysis of colloidal/nano-particles including microorganisms by capillary electrophoresis: a fundamental review

A review is presented on the CE analysis of colloidal/nano particles. Topics discussed include the CE separation of polymeric, inorganic, microbial (i.e. viruses, bacteria, fungi, and whole cells), and sub-cellular particles (i.e. mitochondria and nuclei). Several of the encountered difficulties in analysis are presented as well as the methods employed to overcome them.

Evolution of ion-exchange: from Moses to the Manhattan Project to modern times

This article explores the history of ion-exchange from records of desalination in the Old Testament and the writings of Aristotle, to the identification of the phenomenon of ion-exchange by two English agricultural chemists, to the invention of suppressed conductivity by Small et al. [Anal. Chem. 54 (1975) 462]. It then focuses on the characteristics of the gradual and continuous evolution of ion chromatography with suppressed conductivity to its current state, with an emphasis on those discoveries that punctuated or revolutionized this evolution.

Quantitative capillary zone electrophoresis of inorganic anions

Despite the availability of commercial capillary electrophoresis systems for over ten years, where quantitative analysis is required, capillary zone electrophoresis (CZE) has often failed to replace ion chromatography as the method of choice for a large number of analytes, not least inorganic anions. To investigate the reasons for this apparent failing, a review is presented of work that has been carried out to-date involving the quantitative application of CZE to the determination of inorganic anions in industrial and environmental samples. This review summarizes work both investigating and improving the quantitative aspects of the CZE of inorganic anions. A complete survey of how CZE has been applied to the determination of inorganic anions in real samples is given, including what, if any, analytical performance parameters were investigated and quoted, and if quality assurance data and validation methods were briefly considered, thoroughly investigated or simply ignored.

Analytical separations of lanthanides and actinides by capillary electrophoresis

The separation of lanthanide and actinide elements belongs to one of the most challenging tasks of the separation science, due to a great similarity in their physical and chemical properties. The electrophoretic separation can be accomplished in the presence of suitable complex-forming agents, from which alpha-hydroxyisobutyric acid (HIBA) has been used most often. In the most effective capillary electrophoretic mode--capillary zone electrophoresis (CZE)--a complete separation of lanthanide ions can be accomplished within a few minutes. Various electrophoretic methods can be relatively easily adopted for the determinations of individual lanthanide elements in certain kinds of technical materials, concentrates, precursors, etc., where the high speed and low costs of analysis characteristics of capillary electrophoresis (CE) may be advantageously exploited. Electrophoretic techniques may also be employed for speciation studies, especially for examinations of the behavior of actinides in the environment.

Simultaneous analysis of metabisulfite and sulfate by CE with indirect UV detection. Application to and validation for a pharmaceutical formulation

Metabisulfite is used as an antioxidant agent in a number of pharmaceutical formulations. In order to quantify simultaneously both metabisulfite and its oxidation product (sulfate), a capillary zone electrophoretic (CZE) method with indirect UV detection was developed. Best results were achieved with a background electrolyte (BGE) constituted of 15 mM pyromellitic acid, 15 mM tris-(hydroxymethyl)-aminomethane and 0.2 mM tetradecyltrimethylammonium bromide at pH 8.3 and an applied electrical field of 123 V/cm in a 32.5 cm fused silica capillary. Indirect UV detection was performed at a wavelength of 225 nm. In order to validate this method, an internal standard (IS), namely ammonium formate, was used. Moreover, due to the high chloride concentration in the pharmaceutical formulation, conductivity was adjusted by adding sodium chloride into standard solutions to prevent matrix effect. Linearity and accuracy were successfully tested in a concentration range of 33.3-250 microg/ml for sodium metabisulfite and of 50-375 microg/ml for sodium sulfate. Method precision was determined on six samples each day. Thereby, relative standard deviations (R.S.D.) of 6% and 12-13% were obtained for intra-day and inter-day precision, respectively. Considering the instability of metabisulfite and its use as an antioxidant agent and not as an active principle, the method was accepted and used for routine analyses.

Determination of copper, nickel, cobalt, silver, lead, cadmium, and mercury ions in water by solid-phase extraction and the RP-HPLC with UV-Vis detection

A new method for the simultaneous determination of seven heavy metal ions in water by solid-phase extraction and reversed-phase high-performance liquid chromatography (RP-HPLC) was developed. The copper, nickel, cobalt, silver, lead, cadmium, and mercury ions were pre-column derivatized with tetra( m-aminophenyl)porphyrin (T m-APP) to form colored chelates. The metal-T m-APP chelates in 100 mL of sample were preconcentrated to 1 mL by solid-phase extraction with a C(18 )cartridge; an enrichment factor of 100 was achieved. The chelates were separated on a Waters Xterra()RP(18) column by gradient elution with methanol (containing 0.05 mol L(-1) pyrrolidine-acetic acid buffer salt, pH 10.0) and acetone (containing 0.05 mol L(-1) pyrrolidine-acetic acid buffer salt, pH 10.0) as mobile phase at a flow rate of 1.0 mL min(-1) and detected with a photodiode array detector. The detection limits of copper, cobalt, nickel, silver, lead, cadmium, and mercury are 2, 2, 3, 4, 3, 3, and 3 ng L(-1), respectively, in the original sample. The method was also applied to the determination of these metals in water with good results.

Solid phase extraction and spectrophotometric determination of silver with 2-(2-quinolylazo)-5-diethylaminophenol as chromogenic reagent

A new chromogenic reagent, 2-(2-quinolylazo)-5-diethylaminophenol (QADEAP), was synthesized. A sensitive, selective and rapid method has been developed for the determination of microg/L level silver ion based on the rapid reaction of silver(l) with QADEAP and the solid phase extraction of the colored chelate with C18 cartridge. The QADEAP reacts with Ag(l) to form a violet chelate of a molar ratio 1:2 (silver to QADEAP) in pH 3.5-8.0. This chelate was prconcentrated by solid phase extraction with C18 cartridge. An enrichment factor of 100 was achieved. The molar absorptivity of the chelate is 1.30 x 10(5) L mol(-1) cm(-1) at 590 nm in measured solution. Beer's law is obeyed in the range of 0.01-0.6 microg/ml. The relative standard deviation for eleven replicate samples of 0.01 microg/ml is 1.15%. The detection limit is 0.02 microg/L in the original samples. This method was applied to the determination of microg/L level silver ion in water with good results.