Influence of different surface treatments on the short-term bond strength and durability between a zirconia post and a composite resin core material

Shear bond strength between standard or modified zirconia surfaces and two resin cements incorporating or not 10-MDP in their matrix

OBJECTIVE

This study aimed first to compare the shear bond strength between zirconia samples luted to enamel with a 10-MDP- containing resin cement (Panavia F2.0, Kuraray, Japan) and those luted with a resin cement using a separated 10-MDP monomer-containing bottle (Panavia V5, Kuraray, Japan). The second objective was to evaluate the bond stability after 150 days of aging in water, between enamel and zirconia ceramic surface enhanced with a glass-ceramic coating.

MATERIALS AND METHODS

80 specimens composed of ceramic cylinders and enamel disks were obtained, within eight experimental groups (n = 10). 60 zirconia cylinders (Katana STML zirconia, Kuraray, Japan) were assigned to 3 groups according to their surface treatment: milled/sintered surface (ZRCT), tribochemical silica-coating (Cojet™ Sand, 3 M ESPE, Seefeld, Germany) (ZRTC), and glass-ceramic coating (IPS e.max Zirpress) (ZRZP). 20 cylinders of lithium disilicate had a milled surface (IPS e.max CAD, Ivoclar-Vivadent, Schaan, Liechtenstein) (ECAD). The cylinders of each group were further divided into two subgroups according to the resin cement used: Panavia F2.0 (-PF) and Panavia V5 (-PV). All specimens were stored in distilled water for 150 days before shear bond strength (SBS) tests. The fracture mode was analyzed, and data were statistically computed (two-way ANOVA, post hoc Tukey test, p < 0.05, SPSS, IBM, v26).

RESULTS

The ECAD-PF group recorded the highest SBS values (31.75 ± 2.2), and the ZRCT-PF group recorded the lowest values (5.59 ± 1.1). The two-way ANOVA test showed that ceramic surface treatment had a statistically significant effect on SBS (F (3,72) = 38.95, p < 0.001) while the type of ARC did not (F (1,72) = 2.40, p = 0.126). Tukey's post hoc test revealed no statistical difference between the ZRZP and the ZRTC or ECAD groups.

CONCLUSION

Within the limitations of this study, the PV resin achieved similar shear bond strength results between tribocoated zirconia and enamel compared to the one for glass-ceramic and enamel. Furthermore, a long-term durable bond, similar to the glass-ceramic one, was achieved with the heat pressed ceramic coated specimens. Thus, this new surface treatment could be recommended for anterior cantilever bridges for its fracture resistance and bonding ability.

Adhesive bond strength of monolithic zirconia ceramic finished with various surface treatments

BACKGROUND

This study aimed to investigate different surface treatments thought to increase the bond strength between zirconia ceramic and adhesive resin cement.

METHODS

The samples were prepared in 15 × 10 × 2 mm dimensions by cutting off monolithic zirconia ceramic blocks (Incoris TZI; Sirona, Germany). Surface roughness measurements were made with a profilometer, the average surface roughness (Ra1) was recorded, and five different surface treatments were applied. Group 1: Control group. No surface treatment was applied. Group 2: Sandblasted with Al2O3 under pressure of 50 μm. Group 3: Sandblasted with 30 μm Al2O3 - SiOx under pressure, then tribochemical silica coating, silane bonding agent, and ceramic primer were applied. Group 4: Samples were etched in a hot acid solution containing methanol, HCl, and chloride at 100 °C. Group 5: Samples were coated in a solution containing Grade C Aluminum Nitrite at 75 °C for 15 Sects. 12,000 thermal aging was carried out to all samples. Then, samples were bonded to a composite surface (Filtek Z250) with two different types of adhesive cement (Panavia F 2.0, Rely X U200) (n = 10). A load was applied to the samples attached to the Universal Test Device for the SBS, and the SBS was recorded. The surface roughness measurements of all samples were made again, and the average surface roughness Ra2 was recorded. The data was analyzed with a two-way ANOVA test. Bonferroni correction was used for multiple comparisons of the groups. p = 0.005 was accepted as the statistically significant value.

RESULTS

There was no statistically significant difference between the groups in the Ra1 measurements (p = 0.031). There was a statistically significant difference between the Ra2 values of Groups 4 and 5 and the Ra2 values of Groups 1,2 and 3 in the Ra2 measurements (p < 0.001). There was no statistically significant difference between the SBS values of the groups (p > 0.005). Also, there was no statistically significant difference in the SBS values of all groups for the two different cements tested (p > 0.005).

CONCLUSIONS

None of the surface treatments applied to monolithic zirconia ceramic samples increased the SBS between ceramic and adhesive resin cement.

The effect of adhesive surface with porcelain sintering and two silane coupling agents on the adhesive properties of zirconia

Background

To explore the effect of adhesive surface with porcelain sintering and different silane coupling agents on adhesive properties of zirconia ceramics.

Methods

Zirconia blocks (n=72) were randomly divided into two large groups (n=36) according to whether the adhesive surface was treated with sintered porcelain: N (no porcelain sintering), P (porcelain sintering). Then, according to different silane coupling agents, each group was randomly divided into three small groups, six small groups in total (n=12): NN (no porcelain sintering and agent), NM (no porcelain sintering + Monobond-S), NC (no porcelain sintering + Clearfil Repair); PN (porcelain sintering + no agent), PM (porcelain sintering + Monobond-S), PC (porcelain sintering + Clearfil Repair). After surface treatment, RelyX Unicem Cement was used to make ceramic-resin bonding specimens. Then, each of the six small groups was randomly divided into two subgroups; shear bond strength (SBS) was tested and bond failure mode was analyzed before and after thermal cycling 5,000 times.

Results

(I) SBS analysis: the SBS values of the P groups were significantly higher than those of the N groups (P<0.05). The groups treated with silane coupling agents showed higher SBS values than the control group (P<0.05), and the PC groups showed the highest SBS values (P<0.05). The SBS of each group was significantly decreased after thermal cycling (P<0.05). (II) The microcharacteristics under scanning electron microscopy and energy spectrum analysis: the ceramic blocks being treated by porcelain sintering showed more roughness than the control group. A large amount of silicon (Si) appeared on the surface of the ceramic blocks after porcelain sintering.

Conclusions

(I) Treating the adhesive surface by porcelain sintering can improve the bonding strength between zirconia and RelyX Unicem Cement, and the effect was better in conjunction with silane coupling agent. (II) The two kinds of silane coupling agent (Monobond-S, Clearfil Repair) can improve the bonding strength between zirconia and resin cement. The effect of Clearfil Repair is better than that of Monobond-S. (III) Thermal cycling had a significant adverse effect on SBS between zirconia and RelyX Unicem Cement. Clearfil Repair is helpful in improving the durability of zirconia bonding strength.

Mechanical Properties and Bond Strength of Additively Manufactured and Milled Dental Zirconia: A Pilot Study

PURPOSE

To evaluate and compare the mechanical properties and ceramic bond of additively manufactured and milled dental zirconia materials.

MATERIALS AND METHODS

Disc (r = 10 mm, h = 2 mm) and bar (254) shaped milled (M group) (Nacera Pearl; Doceram) and additively manufactured (AM group) (NanoParticul Jetting; XJet, Carmel 1400) zirconia specimens were prepared for 2 experimental groups. Ceramic was applied to the disc specimens (h = 4 mm, r = 6 mm) (n =9) and their shear bond strength (SBS) was measured. The surface morphology of disc specimens was analyzed with a scanning electron microscope (SEM). The Vickers microhardness (Vh), surface roughness (Ra), and three-point flexural strength (FS) of bar specimens (n = 9) were measured. Results were statistically analyzed with Mann-Whitney U-test (α = 0.05) RESULTS: : Significant differences were found in FS and Vh values of the M and AM groups. M group (1501.4 ± 60.1 HV1) showed a significantly higher Vh value than the AM group (1169.2 ± 48.4 HV1) (p < 0.001). FS of the M group (1287.5 ± 115.2 MPa) exhibited significantly high value than the AM (1030.0 ± 29.2 MPa) group (p < 0.001). Statistically, no significant differences were seen in SBS and Ra values of the M and AM groups.

CONCLUSION

Within the limitations of this in vitro study, the manufacturing technique affected the mechanical properties of the zirconia materials. AM zirconia material showed lower Vh and FS values than M zirconia. Additionally AM zirconia demonstrated adequate bond strength with dental ceramic. This article is protected by copyright. All rights reserved.

[Adhesion of dental cements to zirconia restorations. Part 2]

The information about methods of surface preparation for dentures made from ceramic based on zirconium dioxide for better adhesive fixation is presented in the first part of this article. Micromechanical methods of preparation for cementation of the surface of a zirconia dental prosthesis are discussed in the first part of this article. The second part of the article provides an overview of scientific research on chemical methods for preparing a surface made of zirconia and the problem of the bond strength of polymer cement with a prepared surface made of zirconia.

Effects of dimensions of laser-milled grid-like microslits on shear bond strength between porcelain or indirect composite resin and zirconia

PURPOSE

Zirconia cores and frameworks are widely used in restorative dentistry. Although these structures are veneered with porcelain for esthetic reasons, the use of indirect composite resins (ICRs) is expected to increase in the future. The purpose of this study was to investigate the effects of microslits of different dimensions formed by Nd:YVO 4 laser machining on the bond strength between two types of zirconia (3 mol% yttria-partially stabilized zirconia (Y-TZP) and ceria-partially stabilized zirconia/alumina nanocomposite (Ce-TZP/A)) and porcelain or an ICR.

METHODS

The zirconia disks were assigned as follows: 1) blasted with alumina particles (AB) and 2-4) surface machined with gridded microslits with a width, pitch, and depth of 50, 75, or 100 µm (MS50, MS75, and MS100, respectively). After the bonding of the veneering materials to the disks, half of the specimens veneered with the ICR were subjected to thermocycling (4-60°C, 20000 cycles). All the specimens were subsequently shear tested (n = 10/group).

RESULTS

There was no significant difference between the groups of the disks bonded to porcelain. On the other hand, for the disks bonded to the ICR, the bond strengths of the MS groups after thermocycling were statistically higher than that of the AB group. However, there was no significant difference in the bond strengths of the disks with different microslits.

CONCLUSIONS

Within the study limitations, it can be concluded that, for porcelain, the design of the mechanical retentive structure must be modified. However, for the investigated ICR, a simple gridded pattern can improve the bond strength with zirconia.

Shear bond strength of an acrylic resin to a ceria-stabilized zirconia-alumina nanocomposite

STATEMENT OF PROBLEM

Ceria-stabilized zirconia-alumina nanocomposite (Ce-TZP-Al₂O₃) has properties that may be suitable for partial denture frameworks. However, studies on its adhesion strength and durability with denture base resin are lacking.

PURPOSE

The purpose of this in vitro study was to determine the optimal surface treatment for Ce-TZP-Al₂O₃ to secure a durable bond with an acrylic resin.

MATERIAL AND METHODS

The surface of Ce-TZP-Al₂O₃ test specimens was alumina airborne-particle abraded (Group APA) and then treated with 10-methacryloyloxydecyl dihydrogen phosphate (MDP) (Group MDP) and 2 silica coating methods: the flame spraying method (Group SLP) and the tribochemical treatment (110 μm: Group TRB-P, 30 μm: Group TRB-S). TRB-P and TBR-S were further treated by MDP (Group CBT-P and CBT-S). Autopolymerizing acrylic resin was bonded to the specimens, and the shear bond strength was tested after thermocycling (5 °C and 60 °C, 10 000 cycles). The area of the resin remaining on the fractured surfaces was also measured. To evaluate the effect of the surface treatment condition on shear bond strength and the resin remaining, 1-way analysis of variance (ANOVA) was conducted, followed by the Tukey multiple comparison post hoc test. Additionally, the effect of thermocycling on the specimens was evaluated by the Student t test.

RESULTS

After placement in deionized water for 24 hours, the shear bond strengths of Group MDP and 2 types of combination treatment (Groups CBT-P and CBT-S) were significantly higher than those of Groups SLP, TRB-P, and TRB-S (P<.05). Moreover, the fractured surface of all the treatment conditions except Group APA showed cohesive failure. The shear bond strength as a result of all treatment conditions decreased significantly after thermocycling (P<.05). Group CBT-S showed the highest shear bond strength; however, no significant differences were found between Groups CBT-S and MDP (P=.908). In particular, the area of resin remaining on the fractured surfaces of Group CBT-S was 100% (cohesive failure).

CONCLUSIONS

The combined surface treatment of alumina airborne-particle abrasion and tribochemical treatment, along with primer treatment using silane coupling and an MDP monomer, improved the adhesion strength and adhesion durability between base resins and Ce-TZP-Al₂O₃.

Flexural Strength of Resin Core Build-Up Materials: Correlation to Root Dentin Shear Bond Strength and Pull-Out Force

The aims of this study were to investigate the effects of root dentin shear bond strength and pull-out force of resin core build-up materials on flexural strength immediately after setting, after one-day water storage, and after 20,000 thermocycles. Eight core build-up and three luting materials were investigated, using 10 specimens (n = 10) per subgroup. At three time periods-immediately after setting, after one-day water storage, and after 20,000 thermocycles, shear bond strengths to root dentin and pull-out forces were measured. Flexural strengths were measured using a 3-point bending test. For all core build-up and luting materials, the mean data of flexural strength, shear bond strength and pull-out force were the lowest immediately after setting. After one-day storage, almost all the materials yielded their highest results. A weak, but statistically significant, correlation was found between flexural strength and shear bond strength (r = 0.508, p = 0.0026, n = 33). As the pull-out force increased, the flexural strength of core build-up materials also increased (r = 0.398, p = 0.0218, n = 33). Multiple linear regression analyses were conducted using these three independent factors of flexural strength, pull-out force and root dentin shear bond strength, which showed this relationship: Flexural strength = 3.264 × Shear bond strength + 1.533 × Pull out force + 10.870, p = 0.002). For all the 11 core build-up and luting materials investigated immediately after setting, after one-day storage and after 20,000 thermocycles, their shear bond strengths to root dentin and pull-out forces were correlated to the flexural strength in core build-up materials. It was concluded that the flexural strength results of the core build-up material be used in research and quality control for the predictor of the shear bond strength to the root dentin and the retentive force of the post.

Optimized Er: YAG Laser Irradiation Distance to Achieve the Strongest Bond Strength Between Orthodontic Brackets and Zirconia-Ceramics

Introduction: In recent decades zirconium oxide has been introduced in the field of dentistry as a high-strength ceramic. Unlike its mechanical advantages, however, due to its inert chemical properties, it bonds poorly to other substrates, so improving bonding strength to an adhesive material is necessary. Methods: In this experimental study, 70 ceramic zirconia blocks were prepared and distributed randomly among 7 groups. Then the shear bond strengths were determined and the samples were examined by a scanning electron microscope (SEM). Statistical analysis was performed by one-way ANOVA and multiple Tukey comparisons. Results: One-way analysis of variance (ANOVA) showed that laser irradiation distance has a significant effect on orthodontics brackets bond strength to zirconia-ceramics. Based on the Tukey post hoc test, each group was compared with other groups and the contact mode and 2 mm distance groups showed significantly higher bond strength than other groups (P value <0.05). Conclusion: Orthodontic bracket bond strength to zirconia-ceramics will be reduced by increasing Er: YAG laser irradiation distance from samples. The highest bond strength will be achieved when laser irradiation distance is 2 mm or when the laser beam is in contact with samples.

Zirconia Primers Improve the Shear Bond Strength of Dental Zirconia

PURPOSE

Various resin cements and priming agents are available for adhesive luting of zirconia restorations. The purpose of this study was to investigate how cement type and priming protocol affect the shear bond strength on zirconia ceramics.

MATERIALS AND METHODS

Yttria-stabilized tetragonal zirconia polycrystalline ceramic cylinders were bonded to flat zirconia ceramic surfaces using 7 commercially available resin cements. Ten specimens of each cement group were pretreated with a universal primer, and 10 specimens per group were bonded without pretreatment. In addition, 10 specimens per group were pretreated with system-specific zirconia primers, which were available for 3 cements. Altogether, 170 bonded specimens were water-stored, thermal-cycled, and then submitted to shear bond strength tests. The shear bond strength and the fracture types were documented. Differences in shear bond strengths were assessed using 2-way ANOVA with post-hoc test (α = 0.05). A point-biserial correlation was run between the fracture patterns and the shear bond strengths.

RESULTS

The mean shear bond strengths of cements in the unprimed group showed large variations between 2.52 ± 3.01 (mean ± SD) MPa and 33.15 ± 7.35 MPa. Pretreating the specimens with a universal primer improved the shear bond strengths significantly in all groups (p < 0.05) with a range of 21.80 ± 12.51 to 57.20 ± 11.40 MPa. The system-specific primers also improved the shear bond strength significantly, compared to the unprimed group (p < 0.01); however, only one system-specific primer achieved a shear bond strength superior to the universal primer (p < 0.01). There was also a statistical correlation between the fracture type and the shear bond strength (p < 0.0005), with cohesively fractured specimens showing higher shear bond strengths (37.24 ± 19.87 MPa) than adhesively fractured specimens (23.10 ± 17.65 MPa) (p < 0.001).

CONCLUSION

Using universal primer can enhance the maximal shear bond strength of zirconia.

Effect of Plasma Treatment and Its Post Process Duration on Shear Bonding Strength and Antibacterial Effect of Dental Zirconia

We have investigated the effect of non-thermal atmospheric pressure plasma (NTAPP) treatment and the post process time on the bonding strength and surface sterilization of dental zirconia. Presintered zirconia specimens were manufactured as discs, and then subjected to a 30-min argon treatment (Ar, 99.999%; 10 L/min) using an NTAPP device. Five post-treatment durations were evaluated: control (no treatment), P0 (immediate), P1 (24 h), P2 (48 h), and P3 (72 h). The surface characteristics, shear bonding strength (SBS) with two resin cements, and Streptococcus mutans biofilm formation of these plasma-treated dental zirconia were tested. Plasma did not change the roughness, and caused surface element changes and surface energy increase. Due to this increase in surface energy, SBS increased significantly (p < 0.05) within 48 h when RelyX^TM U200 was used. However, the increase of surface oxygen significantly decreased (p < 0.05) the SBS of Panavia F 2.0 when using plasma immediately (P0). S. mutans adhesion decreased significantly (p < 0.05) for the P0, P1, and P2 groups compared to the control. The P0 group exhibited lower biofilm thickness than the other experimental groups due to the increased hydrophilicity (p < 0.05). Our study suggests that there is a suitable time window for the post NTAPP treatment regarding bonding strength and antimicrobial growth persist.

Bonding durability of titanium tetrafluoride treated glass fiber post with resin cement

This study evaluated the effect of titanium tetrafluoride (TiF₄) solution on the bond strength of glass fiber post to resin cement. The specimens were divided into eight groups according to the method of surface treatment performed. Flexural properties and microtensile bond strength (µTBS) were determined. Data were analyzed using two-way ANOVA and Tukey's post hoc tests. The highest µTBS achieved with the TiF₄ (4 wt/v%-4 min) group compared with the other groups (p<0.05). This finding could be attributed to the effectiveness of TiF₄ (4 wt/v%-4 min) on removing the surface layer of the resin matrix of fiber posts that provides more uncovered surface areas of posts which improved the micromechanical retention of the resin cement. Surface treatments did not affect the flexural properties of fiber posts (p>0.05). Surface treatment of fiber post with TiF₄ (4 wt/v%-4 min) solution exhibited higher bond strength to resin cement compared with other surface treatments.

Evaluation of the Effect of Glow Discharge Plasma Surface Treatment on Bonding Cements to Zirconia

Background:

The major difference in the chemical composition of Y-TZP ceramics, as compared with conventional porcelain, led researchers to develop alternative solutions for achieving durable and long term bonding with the zirconia surface.

Objective:

The study aims to evaluate the effects of glow discharge treatment on the bonding between cement and zirconia.

Methods:

The zirconia rings and rods were prepared with the Zirconia Y-TZP powder and TZ-3YSB-E (Tosoh-Zirconia) through auto-mix to investigate the glow discharge and thermo-cycling. An orientation Teflon mold was used to centralize each rod into the zirconia ring, and aided as a cementation jig during the cementation procedure.

Results:

Cohesive failure (2/3 or more of luting agent remained on the zirconia surface) has been majorly observed with RelyX Ultimate, while adhesion failure (less than 1/3 of the luting agent remained on the zirconia surface) has been primarily observed in Ketac-Cem. Mixed failure was observed among the three specimen including Rely X Unicem 2, Multilink Auto-mix and Ceramir.

Conclusion:

The glow discharge surface treatment procedure had a major impact on bond strength to zirconia.

The effect of continuous application of MDP-containing primer and luting resin cement on bond strength to tribochemical silica-coated Y-TZP

Objectives

This study investigated the effect of continuous application of 10-methacryloyloxydecyldihydrogen phosphate (MDP)-containing primer and luting resin cement on bond strength to tribochemical silica-coated yttria-stabilized tetragonal zirconia polycrystal (Y-TZP).

Materials and Methods

Forty bovine teeth and Y-TZP specimens were prepared. The dentin specimens were embedded in molds, with one side of the dentin exposed for cementation with the zirconia specimen. The Y-TZP specimen was prepared in the form of a cylinder with a diameter of 3 mm and a height of 10 mm. The bonding surface of the Y-TZP specimen was sandblasted with silica-coated aluminium oxide particles. The forty tribochemical silica-coated Y-TZP specimens were cemented to the bovine dentin (4 groups; n = 10) with either an MDP-free primer or an MDP-containing primer and either an MDP-free resin cement or an MDP-containing resin cement. After a shear bond strength (SBS) test, the data were analyzed using 1-way analysis of variance and the Tukey test (α = 0.05).

Results

The group with MDP-free primer and resin cement showed significantly lower SBS values than the MDP-containing groups (p < 0.05). Among the MDP-containing groups, the group with MDP-containing primer and resin cement showed significantly higher SBS values than the other groups (p < 0.05).

Conclusions

The combination of MDP-containing primer and luting cement following tribochemical silica coating to Y-TZP was the best choice among the alternatives tested in this study.

An insight into current concepts and techniques in resin bonding to high strength ceramics

BACKGROUND

Reliable bonding between high strength ceramics and resin composite cement is difficult to achieve because of their chemical inertness and lack of silica content. The aim of this review was to assess the current literature describing methods for resin bonding to ceramics with high flexural strength such as glass-infiltrated alumina and zirconia, densely sintered alumina and yttria-partially stabilized tetragonal zirconia polycrystalline ceramic (Y-TZP) with respect to bond strength and bond durability.

METHODS

Suitable peer reviewed publications in the English language were identified through searches performed in PubMed, Google Search and handsearches. The keywords or phrases used were 'resin-ceramic bond', 'silane coupling agents', 'air particle abrasion', 'zirconia ceramic' and 'resin composite cements'. Studies from January 1989 to June 2015 were included.

RESULTS

The literature demonstrated that there are multiple techniques available for surface treatments but bond strength testing under different investigations have produced conflicting results.

CONCLUSIONS

Within the scope of this review, there is no evidence to support a universal technique of ceramic surface treatment for adhesive cementation. A combination of chemical and mechanical treatments might be the recommended solution. The hydrolytic stability of the resin ceramic bond should be enhanced.

Influence of Veneering Fabrication Techniques and Gas-Phase Fluorination on Bond Strength between Zirconia and Veneering Ceramics

PURPOSE

Porcelain chipping has been one of the main problems of porcelain-fused-to-zirconia restorations. This study evaluates the bond strengths of layered, pressed, and adhesively bonded porcelain to yttria-stabilized zirconia substrates that have undergone traditional preparation or gas-phase fluorination.

MATERIALS AND METHODS

A three-point bending test was used to evaluate the bond strength of the porcelain and zirconia interface. Sixty-six specimens were prepared (n = 11) following ISO 9693 and loaded until failure using an Instron testing machine. One-half of the zirconia substrates received gas phase fluorination treatment before veneering application. Three porcelain veneering methods were evaluated: layered, pressed, and adhesively bonded porcelain. Bond strength results were interpreted using a two-way ANOVA and a Bonferroni multiple comparisons test. Statistical significance was set at α = 0.05.

RESULTS

ANOVA revealed a statistically significant effect of the veneering fabrication methods. No main effect was observed regarding the surface treatment to the zirconia. There was a significant effect related to the veneering method used to apply porcelain to zirconia. For untreated zirconia, layered porcelain had a significantly higher flexural strength compared to pressed or bonded, while pressed and bonded porcelains were not significantly different from one another. For zirconia specimens receiving fluorination treatment, both layered and pressed porcelains had significantly higher bond strengths than adhesively bonded porcelain. In addition, fluorinated pressed porcelain was not statistically different from the control layered or fluorinated layered porcelain.

CONCLUSION

The choice of veneering fabrication technique was critical when evaluating the zirconia to porcelain interfacial bond strength. Bonded porcelain to zirconia had a lower flexural strength than layered or pressed porcelain, regardless of zirconia surface treatment. In addition, fluorination had an effect on the bond strength of pressed porcelain.

Effects of Different Surface Treatment Methods and MDP Monomer on Resin Cementation of Zirconia Ceramics an In Vitro Study

INTRODUCTION

Resin cements are generally preferred for cementation of zirconia ceramics. Resin bonding of zirconia ceramics cannot be done with the same methods of traditional ceramics because zirconia is a silica-free material. In recent years, many methods have been reported in the literature to provide the resin bonding of zirconia ceramics. The purpose of this in vitro study is to evaluate effects of different surface treatments and 10-metacryloxydecyl dihydrogen phosphate (MDP) monomer on shear bond strength between zirconia and resin cement.

METHODS

120 zirconia specimens were treated as follows: Group I: sandblasting, group II: sandblasting + tribochemical silica coating + silane, group III: sandblasting + Nd:YAG (neodymium: yttrium-aluminum-garnet) laser. One specimen from each group was evaluated under scanning electron microscope (SEM). Specimens in each group were bonded either with conventional resin cement Variolink II or with a MDP containing resin cement Panavia F2.0. Subgroups of bonded specimens were stored in distilled water (37°C) for 24 hours or 14 days. Following water storage shear bond strength test was performed at a crosshead speed of 1 mm/min in a universal test machine. Then statistical analyses were performed.

RESULTS

Highest shear bond strength values were observed in group II. No significant difference between group I and III was found when Panavia F2.0 resin cement was used. When Variolink II resin cement was used group III showed significantly higher bond strength than group I. In group I, Panavia F2.0 resin cement showed statistically higher shear bond strength than Variolink II resin cement. In group II no significant difference was found between resin cements. No significant difference was found between specimens stored in 37°C distilled water for 24 hours and 14 days. In group I surface irregularities with sharp edges and grooves were observed. In group II less roughened surface was observed with silica particles. In group III surface microcracks connecting each other were observed.

CONCLUSION

Tribochemical silica coating is an effective method for achieving an acceptable bond between zirconia and resin cement. Use of a MDP monomer containing resin cement increases the bond strength of sandblasted zirconia.

Surface Treatments of Zirconia to Enhance Bonding Durability

This article reviewed the surface treatments used most often to improve adhesion between zirconia and adhesive cements, focusing on their capacity to provide long-term bonding. Traditional and new treatments for zirconia bonding were searched. Some new treatments were discussed along with topographical views of the modified zirconia. New methods, such as selective infiltration etching and the low-fusing glassy porcelain application are promising, but more research is needed.

Resin cementation of zirconia ceramics with different bonding agents

The aim of this study was to evaluate the effects of sandblasting and different chemical bonding agents on shear bond strength of zirconia and conventional resin cement. In this study, 35 zirconia specimens were treated as follows: Group I: control; Group II: sandblasting; Group III: sandblasting + Monobond S; Group IV: sandblasting + Monobond Plus; Group V: sandblasting + Z-Prime Plus. The specimens in each group were bonded with conventional composite resin cement Variolink II. After cementation, specimens were stored in distilled water (at 37 °C) for 24 h and shear test was performed. The highest shear bond strength values were observed in Groups IV and V. The lowest shear bond strength values were observed in Group I. Using 10-methacryloyloxy-decyl dihydrogenphosphate monomer-containing priming agents, e.g. Monobond Plus and Z-PRIME Plus, combined with sandblasting can be an effective method for resin bonding of zirconia restorations.

Evaluation of the shear bond strength of resin cement to Y-TZP ceramic after different surface treatments

The purpose of this study was to evaluate the effect of various surface treatments on the shear bond strength of Y-TZP (Yttria-Tetragonal Zirconia Polycrystal) ceramics with zirconia primer and two different resin cements both containing 10-methacryloyloxydecyl dihydrogen phosphate (MDP). Zirconia blocks (LAVA, 3M ESPE, St. Paul, MN) were polished and assigned to five groups according to the surface treatment: (1) no further treatment (control); (2) airborne abrasion with Al2 O3 particles; (3) Z-PRIME Plus (Bisco, Schaumburg, IL) applied on polished zirconia; (4) Z-PRIME Plus applied on zirconia after airborne abrasion; and (5) tribochemical silica-coating performed with the CoJet system (3M ESPE) followed by application of ESPE®-Sil (3M ESPE). Each group was further divided into one of two resin cements: Panavia F2.0 (Kuraray, Kurashiki, Okayama, Japan) and Clearfil SA Luting (Kuraray). Resin cement placed inside a gel-cap was polymerized on the zirconia surface. Shear bond strength was tested with a universal testing machine at 0.5 mm/min. One-way analysis of variance and paired t-test were done. (p < 0.05), and scanning electron microscope (SEM) images were taken. Zirconia primer applied after airborne abrasion significantly increased the shear bond strength resulting in the highest value for both resin cements. Control groups for both cements showed the weakest value for shear bond strength. No significant differences were found between the shear bond strengths of the individual resin cements applied to zirconia surfaces treated the same way. In conclusion, the combined surface treatment of airborne abrasion followed by a zirconia primer is recommended for zirconia bonding with Panavia F2.0 and Clearfil SA Luting cements.

Influence of air-particle deposition protocols on the surface topography and adhesion of resin cement to zirconia

OBJECTIVES

This study evaluated the influence of air-particle abrasion protocols on the surface roughness (SR) of zirconia and the shear bond strength (SBS) of dual-polymerized resin cement to this ceramic.

MATERIALS AND METHODS

Sintered zirconia blocks (n = 115) (Lava, 3M ESPE) were embedded in acrylic resin and polished. The specimens were divided according to the 'particle type' (Al: 110 µm Al2O3; Si: 110 µm SiO2) and 'pressure' factors (2.5 or 3.5 bar) (n = 3 per group): (a) Control (no air-abrasion); (b) Al2.5; (c) Si2.5; (d) Al3.5; (e) Si3.5. SR (Ra) was measured 3-times from each specimen after 20 s of air-abrasion (distance: 10 mm) using a digital optical profilometer. Surface topography was evaluated under SEM analyses. For the SBS test, 'particle type', 'pressure' and 'thermocycling' (TC) factors were considered (n = 10; n = 10 per group): Control (no air-abrasion); Al2.5; Si2.5; Al3.5; Si3.5; ControlTC; Al2.5TC; Si2.5TC; Al3.5TC; Si3.5TC. After silane application, resin cement (Panavia F2.0) was bonded and polymerized. Specimens were thermocycled (6.000 cycles, 5-55°C) and subjected to SBS (1 mm/min). Data were analyzed using ANOVA, Tukey's and Dunnett tests (5%).

RESULTS

'Particle' (p = 0.0001) and 'pressure' (p = 0.0001) factors significantly affected the SR. All protocols significantly increased the SR (Al2.5: 0.45 ± 0.02; Si2.5: 0.39 ± 0.01; Al3.5: 0.80 ± 0.01; Si3.5: 0.64 ± 0.01 µm) compared to the control group (0.16 ± 0.01 µm). For SBS, only 'particle' factor significantly affected the results (p = 0.015). The SiO2 groups presented significantly higher SBS results than Al2O3 (Al2.5: 4.78 ± 1.86; Si2.5: 7.17 ± 2.62; Al3.5: 4.97 ± 3.74; Si3.5: 9.14 ± 4.09 MPa) and the control group (3.67 ± 3.0 MPa). All TC specimens presented spontaneous debondings. SEM analysis showed that Al2O3 created damage in zirconia in the form of grooves, different from those observed with SiO2 groups.

CONCLUSIONS

Air-abrasion with 110 µm Al2O3 resulted in higher roughness, but air-abrasion protocols with SiO2 promoted better adhesion.

Plasma in dentistry

This review describes the contemporary aspects of plasma application in dentistry. Previous studies on plasma applications were classified into two categories, surface treatment and direct applications, and were reviewed, respectively according to the approach. The current review discussed modification of dental implant surface, enhancing of adhesive qualities, enhancing of polymerization, surface coating and plasma cleaning under the topics of surface treatment. Microbicidal activities, decontamination, root canal disinfection and tooth bleaching were reviewed as direct applications with other miscellaneous ones. Non-thermal atmospheric pressure plasma was of particular focus since it is gaining considerable attention due to the possibility for its use in living tissues. Future perspectives have also been discussed briefly. Although it is still not popular among dentists, plasma has shown promises in several areas of dentistry and is now opening a new era of plasma dentistry.

The effect of post length and core material on root fracture with respect to different post materials

OBJECTIVE

The aim of this study was to evaluate the effect of different core materials and post length on the fracture strength of different posts (CAD/CAM zirconia post (ZR post)) and an individually formed glass fiber reinforced composite post (FRC post).

MATERIALS AND METHODS

One hundred maxillary central incisors received endodontic treatment and were divided into two groups according to the post length: (1) 10 mm in length and (2) 15 mm in length (n = 50/per group). Then the specimens were randomly assigned into five sub-groups (n = 10/per group) as follows: One-piece milled zirconia post and core (group Zr), zirconia post with resin core (Biscore, Bisco) (group Zr/R), zirconia post with resin composite core (Admira, Voco) (group Zr/RC), FRC post with resin core (group F/R) and FRC post with resin composite core (group F/RC). The posts were cemented with a self-adhesive luting agent according to the manufacturer's instructions by using endo tips and light-cured for 40 s using a halogen light curing unit. Metal crowns were made for each specimen, cemented and loaded to failure. Fracture loads (N) and modes of failure were recorded. The data were analyzed using three-way analysis of variance (ANOVA) followed by Tukey's post-hoc test (p < 0.001).

RESULTS

Fracture strength of roots was significantly affected by the type of post material (p < 0.05) and post length (p < 0.05), but not by the type of core materials used (p = 0.078).

CONCLUSION

Longer zirconia posts with zirconia- or resin-based cores can be recommended as an alternative to FRC posts with resin-based cores. The fracture patterns observed in teeth restored with fiber posts were more favorable than teeth restored with zirconia posts. Clinical significance. A higher restoring success rate can be achieved by fiber posts rather than zirconia posts, since the failure mode for these posts would be restorable. Additionally, post length is a more critical factor in teeth restored with one-piece milled zirconia posts than in those restored with fiber posts.

Effects of post surface conditioning before silanization on bond strength between fiber post and resin cement

PURPOSE

Post surface conditioning is necessary to expose the glass fibers to enable bonding between fiber post and resin cement. The purpose of the present study was to evaluate the effect of different surface conditioning on tensile bond strength (TBS) of a glass fiber reinforced post to resin cement.

MATERIALS AND METHODS

In this in vitro study, 40 extracted single canal central incisors were endodontically treated and post spaces were prepared. The teeth were divided into four groups according to the methods of post surface treatment (n=10): 1) Silanization after etching with 20% H₂O₂, 2) Silanization after airborne-particle abrasion, 3) Silanization, and 4) No conditioning (Control). Adhesive resin cement (Panavia F 2.0) was used for cementation of the fiber posts to the root canal dentin. Three slices of 3 mm thick were obtained from each root. A universal testing machine was used with a cross-head speed of 1 mm/minute for performing the push-out tests. Two-way ANOVA and Tukey post hoc tests were used for analyzing data (α=0.05).

RESULTS

It is revealed that different surface treatments and root dentin regions had significant effects on TBS, but the interaction between surface treatments and root canal regions had no significant effect on TBS. There was significant difference among H₂O₂ + Silane Group and other three groups.

CONCLUSION

There were significant differences among the mean TBS values of different surface treatments. Application of hydrogen peroxide before silanization increased the bond strength between resin cements and fiber posts. The mean TBS mean values was significantly greater in the coronal region of root canal than the middle and apical thirds.

Effects of different surface pre-treatments on the bond strength of adhesive resin cement to quartz fiber post

OBJECTIVE

The purpose of this study was to evaluate the effect of mechanical and chemical surface treatment methods on the bond strength of resin cement to fiber post.

MATERIALS AND METHODS

The roots of 36 maxillary central incisor teeth were mounted in auto polymerized acrylic resin blocks (10 × 15 mm) and the root canals were enlarged with the drills of post system (2.1 mm width, 12 mm length). Thirty-six fiber posts were randomly assigned to one of the following surface conditioning methods: silane coupling agent, methylene chloride etching, 24% hydrogen peroxide etching, air abrasion with 50 µm Al(2)O(3), 1-3 µm synthetic diamond particles and silica coating with 30 µm SiO(x). Fiber posts were cemented to the root canals with adhesive resin cement (Panavia F 2.0). Three slices of 1.5 mm thick were obtained from each root. Push-out tests were performed with a universal testing machine. The data were analyzed with one-way analysis of variance (ANOVA) and Tukey HSD tests (α = 0.05). The effect of the surface treatments were examined under a scanning electron microscope (SEM) and surface roughness were evaluated with a profilometer.

RESULTS

Surface pre-treatment methods affected the bond strength (p < 0.05). The highest bond strengths were obtained by air abrasion with synthetic diamond particles, the lowest bond strength were obtained by etching with methylene chloride (p < 0.05).

CONCLUSION

Mechanical surface pre-treatment methods showed higher bond strength values than chemical methods. Synthetic diamond particles may be an alternative method to increase resin cement bonding on the quartz fiber post surfaces.

Comparative evaluation of effects of different surface treatment methods on bond strength between fiber post and composite core

PURPOSE

Debonding of a composite resin core of the fiber post often occurs at the interface between these two materials. The aim of this study was to evaluate the effects of different surface treatment methods on bond strength between fiber posts and composite core.

MATERIALS AND METHODS

Sixty-four fiber posts were picked in two groups (Hetco and Exacto). Each group was further divided into four subgroups using different surface treatments: 1) silanization; 2) sandblasting; 3) Treatment with 24% H₂O₂, and 4) no treatment (control group). A cylindrical plexiglass matrix was placed around the post and filled with the core resin composite. Specimens were stored in 5000 thermal cycles between 5℃ and 55℃. Tensile bond strength (TBS) test and evaluation using stereomicroscope were performed on the specimen and the data were analyzed using two-way ANOVA, Post Hoc Scheffe tests and Fisher's Exact Test (α=.05).

RESULTS

There was a significant difference between the effect of different surface treatments on TBS (P<.001) but different brands of post (P=.743) and interaction between the brand of post and surface treatment (P=.922) had no significant effect on TBS. Both silanization and sandblasting improved the bonding strength of fiber posts to composite resin core, but there were not any significant differences between these groups and control group.

CONCLUSION

There was not any significant difference between two brands of fiber posts that had been used in this study. Although silanization and sandblasting can improve the TBS, there was not any significant differences between surface treatments used.

Composite Resin to Yttria Stabilized Tetragonal Zirconia Polycrystal Bonding: Comparison of Repair Methods

Purpose

The purpose of the current study was to evaluate different approaches for bonding composite to the surface of yttria stabilized tetragonal zirconia polycrystal (Y-TZP) ceramics.

Methods

One hundred Y-TZP blocks were embedded in acrylic resin, had the free surface polished, and were randomly divided into 10 groups (n=10). The tested repair approaches included four surface treatments: tribochemical silica coating (TBS), methacryloxydecyldihidrogenphosphate (MDP)–containing primer/silane, sandblasting, and metal/zirconia primer. Alcohol cleaning was used as a “no treatment” control. Surface treatment was followed by the application (or lack thereof) of an MDP-containing resin cement liner. Subsequently, a composite resin was applied to the ceramic surface using a cylindrical mold (4-mm diameter). After aging for 60 days in water storage, including 6000 thermal cycles, the specimens were submitted to a shear test. Analysis of variance and the Tukey test were used for statistical analyses (α=0.05).

Results

Surface treatment was a statistically significant factor (F=85.42; p&lt;0.0001). The application of the MDP-containing liner had no effect on bond strength (p=0.1017). TBS was the only treatment that had a significantly positive effect on bond strength after aging.

Conclusion

Considering the evaluated approaches, TBS seems to be the best surface treatment for Y-TZP composite repairs. The use of an MDP-containing liner between the composite and Y-TZP surfaces is not effective.

Bond strength between fiber posts and composite resin core: influence of temperature on silane coupling agents

This study evaluated the effect of air drying temperature and different silane coupling agents on the bond strength between glass fiber posts and composite resin core. The post surface was cleaned with alcohol and treated with different silane coupling agents, being three prehydrolyzed silanes [Silano (Angelus), Prosil (FGM), RelyX Ceramic Primer (3M ESPE)] and one two-component silane [Silane Coupling Agent (Dentsply)]. Two post-silanization air drying temperatures, 23ºC and 60ºC, were applied. A cylindrical plastic matrix was placed around the silanized post and filled with composite resin. Each bonded post provided 7 slices for push-out testing. Each slice was loaded to failure under compression at a cross-head speed of 0.5 mm/min. Data were analyzed by two-way ANOVA and Scott-Knott tests (α=0.05). Dunnett's test was used to compare the mean of the control group with that of each experimental group. Scanning electron microscopy (SEM) was used to evaluate the interface of the fractured slices. For the 23ºC air drying temperature, the use of RelyX Ceramic Primer resulted in significantly lower bond strength than the other silane coupling agents, while the bond strength with Silane Coupling Agent was the highest of all groups. Only with Silane Coupling Agent, the bond strength for the 23ºC air drying temperature was significantly higher than that for 60ºC air drying. In conclusion, the use of warm air drying after silane application produced no increase in the bond strength between the fiber-reinforced composite post and the composite core. The two-component silane produced higher bond strength than all prehydrolyzed silanes when it was used with air drying at room temperature.

Effect of air abrasion and dye on the surface element ratio and resin bond of zirconia ceramic

The purpose of this study was to evaluate the effect of the surface element composition and roughness of dyed or non-dyed zirconia ceramic by air abrasion on the bond durability to resin luting cement. The sintered zirconia ceramic specimens were divided into four groups as follows: polished, dyed/polished, abraded, dyed/abraded. The surface roughness of each group was measured by a 3D laser scanning microscope. Energy-dispersive spectroscopy was applied for identifying and quantifying the elemental composition of the zirconia ceramic surfaces Each group had 20 shear test specimens of zirconia to Panavia F and was divided into two subgroups (n = 10) after 0 or 10 000 thermal cycles to receive the shear test. Compared with polishing, air abrasion significantly reduced the oxygen atom and weight ratio, increased the zirconium atom and weight ratio, increased R(a) and R(y) of zirconia ceramic surface, and also increased the bond strength of dyed and non-dyed zirconia ceramic to Panavia F after 0 and 10 000 thermal cycles. The dying procedure could affect the abraded and non-abraded zirconia ceramic surface oxygen and zirconia element ratios and surface characteristics. However, the dying procedure does not affect the resin bond strength and durability of zirconia ceramic.Corrections were made to this article on 3 November 2011. The footnote for the corresponding authors was incorrectly labelled.

Effect of silica coating combined to a MDP-based primer on the resin bond to Y-TZP ceramic

The aim of this study was to evaluate the influence of silica coating and 10-methacryloyloxydecyl dihydrogen phosphate (MDP)-based primer applications upon the bonding durability of a MDP-based resin cement to a yttrium stabilized tetragonal zirconia (Y-TZP) ceramic. Ninety-six Y-TZP tabs were embedded in an acrylic resin (free surface for adhesion: 5 × 5 mm(2)), ground finished and randomly divided into four groups (N = 24) according to the ceramic surface conditioning: (1) cleaning with isopropanol (ALC); (2) ALC + phosphoric acid etching + MDP-based primer application (MDP-primer); (3) silica coating + 3-methacryloyloxypropyl trimethoxysilane (MPS)-based coupling agent application (SiO2 + MPS-Sil); and (4) SiO2 + MDP-primer. The MDP-based resin cement was applied on the treated surface using a cylindrical mold (diameter= 3 mm). Half of the specimens from each surface conditioning were stored in distilled water (37 °C, 24 h) before testing. Another half of the specimens were stored (90 days) and thermo-cycled (12,000 x) during this period (90 d/TC) before testing. A shear bond strength (SBS) test was performed at a crosshead speed of 0.5 mm/min. Two factors composed the experimental design: ceramic conditioning strategy (in four levels) and storage condition (in two levels), totaling eight groups. After 90 d/TC (Tukey; p < 0.05), SiO2 + MDP-primer (24.40 MPa) promoted the highest SBS. The ALC and MDP-primer groups debonded spontaneously during 90 d/TC. Bonding values were higher and more stable in the SiO2 groups. The use of MDP-primer after silica coating increased the bond strength.

Does the surface treatment affect the bond strength of various fibre-post systems to resin-core materials?

OBJECTIVES

The aim of this study was to evaluate the effects of surface treatments on bond strength of resin-core materials to three different types of fibre posts.

METHODS

Prefabricated glass (FRC Postec, Ivoclar), quartz (DT light, Bisco) and individually formed glass (Everstick, Stick Tech) fibre posts with a coronal diameter of 1.5 mm were randomly divided into three groups according to the surface treatment performed. In Group 1 sandblasting with aluminium oxide particles (Rocatec Pre, 3M Espe) was followed by the application of a silane coupling agent. In Group 2, posts were immersed in 9.6% hydrofluoric acid gel for 60 s and silanized for 60 s. In Group 3, no surface treatment was performed and it served as control. The resin-core material (Biscore, Bisco) or resin composites (Admira, Voco) were applied to the tube in 2-mm thick increments and light-cured for 40 s using a halogen light curing unit. 1 mm thick discs (n=10/per group) were prepared for the micropush-out test. The discs were pushed out in a universal testing machine (Lloyd Instruments). Statistical significance was determined by a multifactorial analysis of variance followed by Tukey's post hoc test or independent t tests.

RESULTS

ANOVA revealed that fibre posts and core materials had a significant effect on micropush-out bond strength values (p<0.001). The surface treatment with hydrofluric acid gel and sandblasting with aluminium oxide particles significantly enhanced bond strength values of fibre posts except Everstick post (p<0.05).

CONCLUSION

Different surface treatments of fibre posts might affect the bonding capacity of resin-core systems to these posts.