Novel bioactive materials with different mechanical properties

In vitro and in vivo evaluation of the osseointegration capacity of a polycarbonate-urethane zirconium-oxide composite material for application in a focal knee resurfacing implant

Currently available focal knee resurfacing implants (FKRIs) are fully or partially composed of metals, which show a large disparity in elastic modulus relative to bone and cartilage tissue. Although titanium is known for its excellent osseointegration, the application in FKRIs can lead to potential stress-shielding and metal implants can cause degeneration of the opposing articulating cartilage due to the high resulting contact stresses. Furthermore, metal implants do not allow for follow-up using magnetic resonance imaging (MRI).To overcome the drawbacks of using metal based FKRIs, a biomimetic and MRI compatible bi-layered non-resorbable thermoplastic polycarbonate-urethane (PCU)-based FKRI was developed. The objective of this preclinical study was to evaluate the mechanical properties, biocompatibility and osteoconduction of a novel Bionate® 75D - zirconium oxide (B75D-ZrO2) composite material in vitro and the osseointegration of a B75D-ZrO2 composite stem PCU implant in a caprine animal model. The tensile strength and elastic modulus of the B75D-ZrO2 composite were characterized through in vitro mechanical tests under ambient and physiological conditions. In vitro biocompatibility and osteoconductivity were evaluated by exposing human mesenchymal stem cells to the B75D-ZrO2 composite and culturing the cells under osteogenic conditions. Cell activity and mineralization were assessed and compared to Bionate® 75D (B75D) and titanium disks. The in vivo osseointegration of implants containing a B75D-ZrO2 stem was compared to implants with a B75D stem and titanium stem in a caprine large animal model. After a follow-up of 6 months, bone histomorphometry was performed to assess the bone-to-implant contact area (BIC). Mechanical testing showed that the B75D-ZrO2 composite material possesses an elastic modulus in the range of the elastic modulus reported for trabecular bone. The B75D-ZrO2 composite material facilitated cell mediated mineralization to a comparable extent as titanium. A significantly higher bone-to-implant contact (BIC) score was observed in the B75D-ZrO2 implants compared to the B75D implants. The BIC of B75D-ZrO2 implants was not significantly different compared to titanium implants. A biocompatible B75D-ZrO2 composite approximating the elastic modulus of trabecular bone was developed by compounding B75D with zirconium oxide. In vivo evaluation showed an significant increase of osseointegration for B75D-ZrO2 composite stem implants compared to B75D polymer stem PCU implants. The osseointegration of B75D-ZrO2 composite stem PCU implants was not significantly different in comparison to analogous titanium stem metal implants.

Clinical translation of polycaprolactone-based tissue engineering scaffolds, fabricated via additive manufacturing: A review of their craniofacial applications

The craniofacial region is characterized by its intricate bony anatomy and exposure to heightened functional forces presenting a unique challenge for reconstruction. Additive manufacturing has revolutionized the creation of customized scaffolds with interconnected pores and biomimetic microarchitecture, offering precise adaptation to various craniofacial defects. Within this domain, medical-grade poly(ε-caprolactone) (PCL) has been extensively used for the fabrication of 3D printed scaffolds, specifically tailored for bone regeneration. Its adoption for load-bearing applications was driven mainly by its mechanical properties, adjustable biodegradation rates, and high biocompatibility. The present review aims to consolidating current insights into the clinical translation of PCL-based constructs designed for bone regeneration. It encompasses recent advances in enhancing the mechanical properties and augmenting biodegradation rates of PCL and PCL-based composite scaffolds. Moreover, it delves into various strategies improving cell proliferation and the osteogenic potential of PCL-based materials. These strategies provide insight into the refinement of scaffold microarchitecture, composition, and surface treatments or coatings, that include certain bioactive molecules such as growth factors, proteins, and ceramic nanoparticles. The review critically examines published data on the clinical applications of PCL scaffolds in both extraoral and intraoral craniofacial reconstructions. These applications include cranioplasty, nasal and orbital floor reconstruction, maxillofacial reconstruction, and intraoral bone regeneration. Patient demographics, surgical procedures, follow-up periods, complications and failures are thoroughly discussed. Although results from extraoral applications in the craniofacial region are encouraging, intraoral applications present a high frequency of complications and related failures. Moving forward, future studies should prioritize refining the clinical performance, particularly in the domain of intraoral applications, and providing comprehensive data on the long-term outcomes of PCL-based scaffolds in bone regeneration. Future perspective and limitations regarding the transition of such constructs from bench to bedside are also discussed.

Development of Rapid Bioactivity-Expressed Zr-50Ti Alloys by Surface Treatment with Modified Simulated Body Fluid

Zr-50Ti alloys are promising biomaterials due to their excellent mechanical properties and low magnetic susceptibility. However, Zr-50Ti alloys do not inherently bond well with bone. This study aims to enhance the bioactivity and bonding strength of Zr-50Ti alloys for orthopedic implant materials. Initially, the surface of Zr-50Ti alloys was treated with a sulfuric acid solution to create a microporous structure, increasing surface roughness and area. Subsequently, low crystalline calcium phosphate (L-CaP) precipitation was controlled by adding Mg2+ and/or CO32- ions in modified simulated body fluid (m-SBF). The treated Zr-50Ti alloys were then subjected to cold isostatic pressing to force m-SBF into the micropores, followed by incubation to allow L-CaP formation. The apatite-forming process was tested in simulated body fluid (SBF). The results demonstrated that the incorporation of Mg2+ and/or CO32- ions enabled the L-CaP to cover the entire surface of Zr-50Ti alloys within only one day. After short-term soaking in SBF, the L-CaP layer, modulated by Mg2+ and/or CO32- ions, formed a uniform hydroxyapatite (HA) coating on the surface of the Zr-50Ti alloys, showing potential for optimized bone integration. After soaking in SBF for 14 days, the bonding strength between the apatite layer and alloy has the potential to meet the orthopedic application requirement of 22 MPa. This study demonstrates an effective method to enhance the bioactivity and bonding strength of Zr-50Ti alloys for orthopedic applications.

Platelet-rich fibrin as an autologous biomaterial for bone regeneration: mechanisms, applications, optimization

Platelet-rich fibrin, a classical autologous-derived bioactive material, consists of a fibrin scaffold and its internal loading of growth factors, platelets, and leukocytes, with the gradual degradation of the fibrin scaffold and the slow release of physiological doses of growth factors. PRF promotes vascular regeneration, promotes the proliferation and migration of osteoblast-related cells such as mesenchymal cells, osteoblasts, and osteoclasts while having certain immunomodulatory and anti-bacterial effects. PRF has excellent osteogenic potential and has been widely used in the field of bone tissue engineering and dentistry. However, there are still some limitations of PRF, and the improvement of its biological properties is one of the most important issues to be solved. Therefore, it is often combined with bone tissue engineering scaffolds to enhance its mechanical properties and delay its degradation. In this paper, we present a systematic review of the development of platelet-rich derivatives, the structure and biological properties of PRF, osteogenic mechanisms, applications, and optimization to broaden their clinical applications and provide guidance for their clinical translation.

Green Synthesis and Biosafety Assessment of MXene

The rise of MXene-based materials with fascinating physical and chemical properties has attracted wide attention in the field of biomedicine, because it can be exploited to regulate a variety of biological processes. The biomedical applications of MXene are still in its infancy, nevertheless, the comprehensive evaluation of MXene's biosafety is desperately needed. In this review, the composition and the synthetic methods of MXene materials are first introduced from the view of biosafety. The evaluation of the interaction between MXene and cells, as well as the safety of different forms of MXene applied in vivo are then discussed. This review provides a basic understanding of MXene biosafety and may bring new inspirations to the future applications of MXene-based materials in biomedicine.

Obtaining Polyvinylpyrrolidone Fibers Using the Electroforming Method with the Inclusion of Microcrystalline High-Temperature Phosphates

The results of the synthesis of microcrystalline calcium phosphates such as hydroxoapatite, pyrophosphate, and tricalcium phosphate are presented herein. The influence of the addition of polyvinylpyrrolidone (PVP) on the phase characteristics of the resulting high-temperature ceramic sample is considered. The X-ray results show that hydroxyapatite (HAp) consists of a Ca5(PO4)3(OH) phase, while the sample with the addition of polyvinylpyrrolidone contains β-Ca3(PO4)2 (65.5%) and β-Ca2P2O7 (34.5%) phases calcium phosphates (CPs). IR spectroscopy was used to characterize the compositions of the samples. An important characteristic of the obtained samples is the elemental Ca/P ratio, which was determined via energy-dispersive analysis. The data obtained are consistent with the composition of dental enamel apatites, namely, in the CPs (1.27) and HAp (1.40). SEM was used to study the morphology of the surfaces of hydroxyapatite particles. Polyvinylpyrrolidone polymer fibers were obtained using the electroforming method with the inclusion of CPs in the composition. The fibers were oriented randomly, and nanoscale hydroxyapatite particles were incorporated into the fiber structure. Solubility data of the HAp, CPs, and Fibers in a physiological solution at room temperature and human body temperature were obtained. The solubility of the resulting HAp turned out to be higher than the solubility of the CPs. In turn, the concentration of Ca2+ in a physiological solution of PVP composite fibers with the inclusion of CPs was lower than that in powdered CPs.

Development and Characterization of Gadolinium and Copper Reinforced Bioactive Glass: An In Vitro Study

INTRODUCTION

Bioactive glass, an innovative alloplastic material utilizing a matrix of silica particles combined with calcium and phosphorus, has been widely employed for the regeneration of bony defects due to its bone-forming capabilities and biocompatibility. Nevertheless, it comes with several drawbacks, including a slow degradation rate, low mechanical strength, and susceptibility to fractures. To address these issues, the present research was done to develop and characterize a novel bioactive glass incorporating gadolinium (Gd) and copper (Cu).

METHODS

The bioactive glass doped with Gd and Cu were synthesized and subjected to characterization through X-ray diffraction (XRD), scanning electron microscopy (SEM), and attenuated total reflectance-infrared (ATR-IR) analysis.

RESULTS

The bioactive glass, enriched with Gd and Cu, underwent analysis using ATR-IR spectroscopy, XRD, and SEM. ATR-IR revealed characteristic silicate bands, while SEM indicated the presence of particles larger than 4 μm. XRD analysis identified the formation of Na2Ca4(PO4)2SiO4 (Silicorhenatite), Na2Ca2Si3O9 (Combeite), and wollastonite (calcium inosilicate mineral; CaSiO3). The crystalline nature of these compounds contributed to the favorable mechanical properties of the bioactive glass.

CONCLUSION

In summary, the creation of the innovative Gd-Cu-incorporated bioactive glass demonstrates favorable mechanical characteristics, suggesting significant promise for augmenting bone regeneration.

New 3D Printed Scaffolds Based on Walstromite Synthesized by Sol-Gel Method

This study explores the potential utilization of walstromite (BaCa2Si3O9) as a foundational material for creating new bioceramics in the form of scaffolds through 3D printing technology. To achieve this objective, this study investigates the chemical-mineralogical, morphological, and structural characteristics, as well as the biological properties, of walstromite-based bioceramics. The precursor mixture for walstromite synthesis is prepared through the sol-gel method, utilizing pure reagents. The resulting dried gelatinous precipitate is analyzed through complex thermal analysis, leading to the determination of the optimal calcination temperature. Subsequently, the calcined powder is characterized via X-ray diffraction and scanning electron microscopy, indicating the presence of calcium and barium silicates, as well as monocalcium silicate. This powder is then employed in additive 3D printing, resulting in ceramic scaffolds. The specific ceramic properties of the scaffold, such as apparent density, absorption, open porosity, and compressive strength, are assessed and fall within practical use limits. X-ray diffraction analysis confirms the formation of walstromite as a single phase in the ceramic scaffold. In vitro studies involving immersion in simulated body fluid (SBF) for 7 and 14 days, as well as contact with osteoblast-like cells, reveal the scaffold's ability to form a phosphate layer on its surface and its biocompatibility. This study concludes that the walstromite-based ceramic scaffold exhibits promising characteristics for potential applications in bone regeneration and tissue engineering.

Use of biosilica to improve loading and delivery of bone morphogenic protein 2

The clinical utility of bone morphogenetic protein 2 (BMP2) is limited because of the poor attraction between BMP2 and carriers, resulting in low loading efficiency and initial burst release. Here, the high binding affinity of BMP2 to the biosilica surface was utilized to overcome this limitation. Atomic force microscopy revealed that BMP2 bound nearly 8- and 2-fold more strongly to biosilica-coated hydroxyapatite than to uncoated and plain silica-coated hydroxyapatite, respectively. To achieve controlled release, collagen was introduced between the silica layers on hydroxyapatite, which was optimized by adjusting the collagen concentration and number of layers. The optimal biosilica/collagen formulation induced sustained BMP2 release without compromising loading efficiency. BMP2 combined with the mentioned formulation led to an increase in osteogenesis, as compared to the combination of BMP2 with either biosilica-coated or non-coated hydroxyapatite in vitro. In rat calvarial defect models, the biosilica/collagen-coated hydroxyapatite with 1 μg BMP2 showed 26 % more bone regeneration than the same dose of BMP2-loaded hydroxyapatite and 10.6 % more than hydroxyapatite with 2.5-fold dose of BMP2. Using BMP2 affinity carriers coated with biosilica/collagen allows for more efficacious in situ loading and delivery of BMP2, making them suitable for the clinical application of growth factors through a soaking method.

Functionalized Magnesium Phosphate Cement Induces In Situ Vascularized Bone Regeneration via Surface Lyophilization of Chondroitin Sulfate

Bone defect repair poses significant challenges in orthopedics, thereby increasing the demand for bone substitutes. Magnesium phosphate cements (MPCs) are widely used for bone defect repair because of their excellent mechanical properties and biodegradability. However, high crystallinity and uncontrolled magnesium ion (Mg2+) release limit the surface bioactivity of MPCs in bone regeneration. Here, we fabricate chondroitin sulfate (CS) as a surface coating via the lyophilization method, namely CMPC. We find that the CS coating is uniformly distributed and improves the mechanical properties of MPC through anionic electrostatic adsorption, while mediating degradation-related controlled ion release of Mg2+. Using a combination of in vitro and in vivo analyses, we show that the CS coating maintained cytocompatibility while increasing the cell adhesion area of MC3T3-E1s. Furthermore, we display accelerated osteogenesis and angiogenesis of CMPC, which are related to appropriate ion concentration of Mg2+. Our findings reveal that the preparation of a lyophilized CS coating is an effective method to promote surface bioactivity and mediate Mg2+ concentration dependent osteogenesis and angiogenesis, which have great potential in bone regeneration.

Influence of Strontium on the Biological Behavior of Bioactive Glasses for Bone Regeneration

Bioactive glasses (BGs) can potentially be applied in biomedicine, mainly for bone repair and replacement, given their unique ability to connect to natural bone tissue and stimulate bone regeneration. Since their discovery, several glass compositions have been developed to improve the properties and clinical abilities of traditional bioactive glass. Different inorganic ions, such as strontium (Sr2+), have been incorporated in BG due to their ability to perform therapeutic functions. Sr2+ has been gaining prominence due to its ability to stimulate osteogenesis, providing an appropriate environment to improve bone regeneration, in addition to its antibacterial potential. However, as there are still points in the literature that are not well consolidated, such as the influence of ionic concentrations and the BG production technique, this review aims to collect information on the state of the art of the biological behavior of BGs containing Sr2+. It also aims to gather data on different types of BGs doped with different concentrations of Sr2+, and to highlight the manufacturing techniques used in order to analyze the influence of the incorporation of this ion for bone regeneration purposes.

Fabrication and Characterization of an Innovative Silver- and Gadolinium-Doped Bioglass for Bone Regeneration

Background Periodontal regeneration aims for the three-dimensional reconstruction of bone defects, and over the years, bone grafts with or without barrier membranes have provided us with promising results. Particulate bone grafts can be classified according to the source of procurement as autografts, allografts, xenografts, and alloplasts. Bioglass, an innovative alloplast that uses silica particles as a matrix incorporated with calcium and phosphorus, has been extensively used as a propitious material for bone regeneration owing to its inherent osteogenic ability and biocompatibility but presents with various disadvantages such as slow degradation rate, low mechanical strength, and fracture resistance. A novel silver (Ag)-gadolinium (Gd)-doped bioglass was fabricated to improve the mechanical properties, biocompatibility, and osteogenic ability when compared with bioglass (control). Materials and methods The Ag- and Gd-doped bioglass network was prepared and assessed for the morphological and structural properties by scanning electron microscopy (SEM) analysis, X-ray diffraction (XRD), and attenuated total reflectance (ATR)-infrared (IR). The cytotoxicity of Gd and Ag-doped bioglass was assessed using the MG63 cell line through the MTT (3-(4,5-dimethylthiazol-2-yl)-2,5 diphenyl tetrazolium bromide) assay at various concentrations and the absorbance of the solution was measured at 570 nm using a microplate reader. The osteogenic ability of the material was assessed by alkaline phosphatase activity and collagen estimation. Results ATR-IR spectroscopy, SEM, and XRD were used to examine the bioglass network doped with Gd and Ag. ATR-IR exhibited classic silicate bands, whereas SEM indicated particles bigger than 5 μm. XRD analysis revealed the production of Na2Ca2Si3O9, Na2Ca4(PO4)2SiO4, and wollastonite. The excellent crystallinity of Na2Ca2Si3O9 provided the bioglass network with good mechanical characteristics. The Gd-Ag-bioglass did not exhibit any toxicity towards the living cells at increasing concentrations from 12.5 µg to 100 µg. The alkaline phosphatase activity was increased by 10% and the collagen estimation remained consistent with bioglass (control). Conclusion In conclusion, the fabrication of the novel Gd-Ag-doped bioglass shows good cytocompatibility and osteogenic ability and shows great potential to enhance bone regeneration.

Multifunctional nacre-like materials

Nacre, the iridescent inner layer of seashells, displays an exceptional combination of strength and toughness due to its 'brick-wall' architecture. Significant research has been devoted to replicating nacre's architecture and its associated deformation and failure mechanisms. Using the resulting materials in applications necessitates adding functionalities such as self-healing, force sensing, bioactivity, heat conductivity and resistance, transparency, and electromagnetic interference shielding. Herein, progress in the fabrication, mechanics, and multi-functionality of nacre-like materials, particularly over the past three years is systematically and critically reviewed. The fabrication techniques reviewed include 3D printing, freeze-casting, mixing/coating-assembling, and laser engraving. The mechanical properties of the resulting materials are discussed in comparison with their constituents and previously developed nacre mimics. Subsequently, the progress in incorporating multifunctionalities and the resulting physical, chemical, and biological properties are evaluated. We finally provide suggestions based on 3D/4D printing, advanced modelling techniques, and machine elements to make reprogrammable nacre-like components with complex shapes and small building blocks, tackling some of the main challenges in the science and translation of these materials.

Morphological Reconstruction of a Critical-Sized Bone Defect in the Maxillofacial Region Using Modified Chitosan in Rats with Sub-Compensated Type I Diabetes Mellitus

It is known that complexes based on natural polysaccharides are able to eliminate bone defects. Prolonged hyperglycemia leads to low bone regeneration and a chronic inflammatory response. The purpose of this study was to increase the efficiency of early bone formation in a cavity of critical size in diabetes mellitus in the experiment. The polyelectrolyte complex contains high-molecular ascorbate of chitosan, chondroitin sulfate, sodium hyaluronate, heparin, adgelon serum growth factor, sodium alginate and amorphous nanohydroxyapatite (CH-SA-HA). Studies were conducted on five groups of white female Wistar rats: group 1-regeneration of a bone defect in healthy animals under a blood clot; group 2-regeneration of a bone defect under a blood clot in animals with diabetes mellitus; group 3-bone regeneration in animals with diabetes mellitus after filling the bone cavity with a collagen sponge; group 4-filling of a bone defect with a CH-SA-HA construct in healthy animals; group 5-filling of a bone defect with a CH-SA-HA construct in animals with diabetes mellitus. Implantation of the CH-SA-HA construct into bone cavities in type I diabetic rats can accelerate the rate of bone tissue repair. The inclusion of modifying polysaccharides and apatite agents in the construction may be a prospect for further improvement of the properties of implants.

PRP coating on different modified surfaces promoting the osteointegration of polyetheretherketone implant

Introduction: Polyetheretherketone (PEEK) material implants have been applied more and more clinically recently. In order to increase the osteogenic activity of PEEK material, the microstructure change of the material surface and the construction of functional microcoatings have become a hot research topic. This study investigated the ability of PEEK surfaces modified by different methods to carry Platelet-rich plasma (PRP) and the osteogenic ability of different PEEK microstructures after carrying PRP in vivo/in vitro. Methods: In this study, PEEK surfaces were modified by sulfuric acid, gaseous sulfur trioxide and sandpaper. Next, PRP from SD rats was prepared and incubated on PEEK material with different surface microstructures. Lactate dehydrogenase test, scanning electron microscope and Elisa assay was used to evaluate adhesion efficiency of PRP. Then in vitro tests such as CCK-8, ALP staining, ARS staining and RT-qPCR et al were used to further evaluate osteogenesis ability of the PRP coating on PEEK surface. Finally, The tibia defects of SD rats were established, and the new bone was evaluated by Micro-CT, HE staining, and immunofluorescence staining. Results: The sandpaper-polished PEEK with the strongest PRP carrying capacity showed the best osteogenesis. Our study found that the modified PEEK surface with PRP coating has excellent osteogenic ability and provided the basis for the interface selection of PRP for the further application of PEEK materials. Discussion: Among the three PEEK modified surfaces, due to the most PRP carrying and the strongest osteogenic ability in vitro/vivo, the frosted surface was considered to be the most suitable surface for the preparation of PRP coating.

Silver-releasing bioactive glass nanoparticles for infected tissue regeneration

Bacterial infections represent a formidable challenge, often leaving behind significant bone defects post-debridement and necessitating prolonged antibiotic treatments. The rise of antibiotic-resistant bacterial strains further complicates infection management. Bioactive glass nanoparticles have been presented as a promising substitute for bone defects and as carriers for therapeutic agents against microorganisms. Achieving consistent incorporation of ions into BGNs has proven challenging and restricted to a maximum ion concentration, especially when reducing the particle size. This study presents a notable achievement in the synthesis of 10 nm-sized Ag-doped bioactive glass nanoparticles (Ag-BGNs) using a modified yet straightforward Stöber method. The successful incorporation of essential elements, including P, Ca, Al, and Ag, into the glass structure at the intended concentrations (i.e., CaO wt% above 20 %) was confirmed by EDS, signifying a significant advancement in nanoscale biomaterial engineering. While exhibiting a spherical morphology and moderate dispersity, these nanoparticles tend to form submicron-sized aggregates outside of a solution state. The antibacterial effectiveness against MRSA was established across various experimental conditions, with Ag-BGNs effectively sterilizing planktonic bacteria without the need for antibiotics. Remarkably, when combined with oxacillin or fosfomycin, Ag-BGNs demonstrated a potent synergistic effect, restoring antibacterial capabilities against MRSA strains resistant to these antibiotics when used alone. Ag-BGNs exhibited potential in promoting human mesenchymal stromal cell proliferation, inducing the upregulation of osteoblast gene markers, and significantly contributing to bone regeneration in mice. This innovative synthesis protocol holds substantial promise for the development of biomaterials dedicated to the regeneration of infected tissue.

Effect of GO content on microstructure and mechanical properties of Ti6Al4V coating reinforced artificial joint

In this study, we have innovatively proposed a method of in-situ synthesized TiC hard phase to improve the surface mechanical properties of artificial joint materials (Ti6Al4V). In order to explore the optimum graphene oxide (GO) addition, GO/Ti6Al4V composite powders with different proportions (0, 0.5, 1.0, and 1.5 wt.%) were prepared. The homogeneously dispersed GO/Ti6Al4V composite powder was prepared on Ti6Al4V substrate by laser cladding technology. The microstructure, phase composition, and mechanical behavior of GO/Ti6Al4V composite coatings were studied by scanning electron microscope (SEM), optical microscope (OM), energy dispersive spectrometer (EDS), tribometer, hardness tester, and surface profiler. The results showed that the addition of GO could significantly improve the mechanical properties of TC4 substrate. During the preparation of the coating, the grain size of in-situ TiC phase was nanoscale and was distributed between acicular martensite, which played a critical role in enhancing the mechanical properties of the coating. The TiC phase distributed between acicular martensite refine the grain size of α ' phase and improve the cutting resistance of the coating. Nevertheless, excessive GO decreased the fluidity of the molten pool, and micro holes tended to generate in the coating, which had a negative impact on the mechanical properties of the coating. At the GO content of 0.5 wt.%, the microhardness of the GO/Ti6Al4V coating was 1.325 times that of pure Ti6Al4V. Under the friction environment of simulated body fluid solution, the average friction coefficient was approximately 0.307 and the wear rate decreased to 3.5 × 10-7 mm3/N · m.

UV-Cured Bio-Based Acrylated Soybean Oil Scaffold Reinforced with Bioactive Glasses

In this study, a bio-based acrylate resin derived from soybean oil was used in combination with a reactive diluent, isobornyl acrylate, to synthetize a composite scaffold reinforced with bioactive glass particles. The formulation contained acrylated epoxidized soybean oil (AESO), isobornyl acrylate (IBOA), a photo-initiator (Irgacure 819) and a bioactive glass particle. The resin showed high reactivity towards radical photopolymerisation, and the presence of the bioactive glass did not significantly affect the photocuring process. The 3D-printed samples showed different properties from the mould-polymerised samples. The glass transition temperature Tg showed an increase of 3D samples with increasing bioactive glass content, attributed to the layer-by-layer curing process that resulted in improved interaction between the bioactive glass and the polymer matrix. Scanning electron microscope analysis revealed an optimal distribution on bioactive glass within the samples. Compression tests indicated that the 3D-printed sample exhibited higher modulus compared to mould-synthetized samples, proving the enhanced mechanical behaviour of 3D-printed scaffolds. The cytocompatibility and biocompatibility of the samples were evaluated using human bone marrow mesenchymal stem cells (bMSCs). The metabolic activity and attachment of cells on the samples' surfaces were analysed, and the results demonstrated higher metabolic activity and increased cell attachment on the surfaces containing higher bioactive glass content. The viability of the cells was further confirmed through live/dead staining and reseeding experiments. Overall, this study presents a novel approach for fabricating bioactive glass reinforced scaffolds using 3D printing technology, offering potential applications in tissue engineering.

Cell seeding via bioprinted hydrogels supports cell migration into porous apatite-wollastonite bioceramic scaffolds for bone tissue engineering

Cell seeding via cell-laden hydrogels offers a rapid way of depositing cells onto a substrate or scaffold. When appropriately formulated, hydrogels provide a dense network of fibres for cellular encapsulation and attachment, creating a protective environment that prevents cells to be washed away by media. However, when incorporating hydrogels into a cell seeding strategy the cellular capacity for migration from a hydrogel network and subsequent biofunctionality must be assessed. Here, we compare cell seeding via a bioprinted hydrogel with conventional manual cell seeding in media. To this end, we use a binder jet 3D printed bioceramic scaffold as a model system for bone tissue engineering and the reactive jet impingement (ReJI) bioprinting system to deliver high cell density cell-laden hydrogels onto the surface of the scaffolds. The bioceramic scaffolds were produced in apatite-wollastonite (AW) glass-ceramic, with a total porosity of ~50 %, with pore size predominantly around 50-200 μm. Bone marrow-derived mesenchymal stromal cells were seeded onto the porous AW substrate both in media and via ReJI bioprinting. Cell seeding in media confirmed the osteoinductive nature and the ability of the scaffold to support cell migration within the porous structure. Cell seeding via ReJI bioprinting demonstrated that the cell-laden hydrogel penetrated the porous AW structure upon hydrogel deposition. Furthermore, cells would then migrate out from the hydrogel network and interact with the bioceramic substrate. Overall, levels of cell migration and mineralisation were significant and comparable for both seeding approaches. However, cell seeding via bioprinted hydrogels may serve as an effective strategy for in situ cell seeding into implants, which is desired in clinical tissue engineering procedures, avoiding the time taken for cell attachment from media, and the requirement to maintain a specific orientation until attachment has occurred.

ZIF-8 induced hydroxyapatite-like crystals enabled superior osteogenic ability of MEW printing PCL scaffolds

ZIF-8 may experience ion-responsive degradation in ionic solutions, which will change its initial architecture and restrict its direct biological use. Herein, we report an abnormal phenomenon in which ZIF-8 induces large hydroxyapatite-like crystals when soaked directly in simulated body fluid. These crystals grew rapidly continuously for two weeks, with the volume increasing by over 10 folds. According to Zn2+ release and novel XRD diffraction peak presence, ZIF-8 particles can probably show gradual collapse and became congregate through re-nucleation and competitive coordination. The phenomenon could be found on ZIF-8/PCL composite surface and printed ZIF-8/PCL scaffold surface. ZIF-8 enhanced PCL roughness through changing the surface topography, while obviously improving the in-vivo and in-vitro osteoinductivity and biocompatibility. The pro-biomineralization property can make ZIF-8 also applicable in polylactic acid-based biomaterials. In summary, this study demonstrates that ZIF-8 may play the role of a bioactive additive enabling the surface modification of synthetic polymers, indicating that it can be applied in in-situ bone regeneration.

Mechanical and bioactive properties of PVD TiO2 coating modified PEEK for biomedical applications

Polyetheretherketone (PEEK) is gaining popularity in the biomedical field due to its excellent mechanical properties, chemical resistance and biocompatibility. Although PEEK is an excellent biomaterial, it may require bulk surface modification to tailor its properties for specific biomedical applications. In this study, the surface modification of PEEK was achieved by depositing titanium dioxide (TiO2) by PVD method. The microstructure and mechanical properties of TiO2 coatings were studied by SEM/EDS and nanoindentation tests. Conventional scratch tests were performed to determine the adhesion and tribological properties of the TiO2 films. An in vitro study was performed in simulated body fluids to evaluate the osteocompatibility of TiO2 coated PEEK. According to the results The TiO2 coating has a dense microstructure and good adhesion, the critical cohesive load Lc1 is greater than 1N. The TiO2 film improved the mechanical properties of the PEEK substrate: hardness and elastic modulus increased from ∼0.33 to ∼4.03 GPa to ∼3.6 and ∼21.85 GPa, respectively. In addition, compared with the PEEK substrate, the coating showed a 61% improvement in wear resistance and a reduction in the coefficient of friction from 0.38 to 0.09. The results also showed that the TiO2 coating induces the formation of hydroxyapatite on the surface, which promotes the osteocompatibility of PEEK.

Effect of HA Content on Microstructure and Properties of Ti-27Nb-17Ta-8Zr/HA Composite

In this paper, Ti-27Nb-17Ta-8Zr/HA series composite materials were prepared by spark plasma sintering (SPS) technology. The medical titanium alloy (Ti-27Nb-17Ta-8Zr) with good mechanical properties, wear resistance, and corrosion resistance was combined with the hydroxyapatite (HA) bioactive ceramic with high biological activity and bone-binding ability. Moreover, the density, microstructure evolution, metal/ceramic reaction, mechanical behavior, in vitro bioactivity, and influencing mechanisms of composite materials with different HA contents were studied. The research results indicate that all biological composite materials are composed of β-Ti solution, α-Ti, and ceramic phases (T_i2O, CaTiO₃, CaO, Ti_xP_y). With the increase of HA content, the compressive strength and yield strength of the composite material show a trend of first increasing, then decreasing, and then slowly increasing. After soaking in SBF artificial simulated body fluid for 5 days, the deposition of elements such as Ca and P on the surface significantly increased, while elements such as Ti, Nb, Ta, and Zr were evenly distributed in the matrix, demonstrating good in vitro mineralization ability and facilitating the attachment and growth of osteoblasts.

α-Tricalcium phosphate cement reinforced with silk fibroin: A high strength biomimetic bone cement with chloride-substituted hydroxyapatite

In the past decades, bone defects have become an increasing factor in the development of disability in patients, impacting their quality of life. Large bone defects have minor chances to self-repair, requiring surgical intervention. Therefore, α-TCP-based cements are rigorously studied for the development of bone filling and replacement applications due to the possibility of application in minimally invasive procedures. However, α-TCP-based cements do not present adequate mechanical properties for most orthopedic applications. The aim of this study is to develop a biomimetic α-TCP cement reinforced with 0.250-1.000 wt% of silk fibroin using non-dialyzed SF solutions. Samples with SF additions higher than 0.250 wt% presented complete transformation of the α-TCP to a biphasic CDHA/HAp-Cl material, which could enhance the osteoconductivity of the material. Samples reinforced with concentrations of 0.500 wt% SF showed an increase of 450% of the fracture toughness and 182% of the compressive strength of the control sample, even with 31.09% porosity, which demonstrates good coupling between the SF and the CPs. All samples reinforced with SF showed a microstructure with smaller needle-like crystals when compared to the control sample, which possibly contributed to the material's reinforcement. Moreover, the composition of reinforced samples did not affect the cytotoxicity of the CPCs and enhanced the cell viability presented by the CPC without SF addition. Hence, biomimetic CPCs with mechanical reinforcement through the addition of SF were successfully obtained through the developed methodology, with the potential to be further evaluated as a suitable material for bone regeneration.

There Are over 60 Ways to Produce Biocompatible Calcium Orthophosphate (CaPO4) Deposits on Various Substrates

A The present overview describes various production techniques for biocompatible calcium orthophosphate (abbreviated as CaPO4) deposits (coatings, films and layers) on the surfaces of various types of substrates to impart the biocompatible properties for artificial bone grafts. Since, after being implanted, the grafts always interact with the surrounding biological tissues at the interfaces, their surface properties are considered critical to clinical success. Due to the limited number of materials that can be tolerated in vivo, a new specialty of surface engineering has been developed to desirably modify any unacceptable material surface characteristics while maintaining the useful bulk performance. In 1975, the development of this approach led to the emergence of a special class of artificial bone grafts, in which various mechanically stable (and thus suitable for load-bearing applications) implantable biomaterials and artificial devices were coated with CaPO4. Since then, more than 7500 papers have been published on this subject and more than 500 new publications are added annually. In this review, a comprehensive analysis of the available literature has been performed with the main goal of finding as many deposition techniques as possible and more than 60 methods (double that if all known modifications are counted) for producing CaPO4 deposits on various substrates have been systematically described. Thus, besides the introduction, general knowledge and terminology, this review consists of two unequal parts. The first (bigger) part is a comprehensive summary of the known CaPO4 deposition techniques both currently used and discontinued/underdeveloped ones with brief descriptions of their major physical and chemical principles coupled with the key process parameters (when possible) to inform readers of their existence and remind them of the unused ones. The second (smaller) part includes fleeting essays on the most important properties and current biomedical applications of the CaPO4 deposits with an indication of possible future developments.

Atomic Layer Deposition of Tantalum Oxide Films on 3D-Printed Ti6Al4V Scaffolds with Enhanced Osteogenic Property for Orthopedic Implants

There is an evident advantage in personalized customization of orthopedic implants by 3D-printed titanium (Ti) and its alloys. However, 3D-printed Ti alloys have a rough surface structure caused by adhesion powders and a relatively bioinert surface. Therefore, surface modification techniques are needed to improve the biocompatibility of 3D-printed Ti alloy implants. In the present study, porous Ti6Al4V scaffolds were manufactured by a selective laser melting 3D printer, followed by sandblasting and acid-etching treatment and atomic layer deposition (ALD) of tantalum oxide films. SEM morphology and surface roughness tests confirmed that the unmelted powders adhered on the scaffolds were removed by sandblasting and acid-etching. Accordingly, the porosity of the scaffold increased by about 7%. Benefiting from the self-limitation and three-dimensional conformance of ALD, uniform tantalum oxide films were formed on the inner and outer surfaces of the scaffolds. Zeta potential decreased by 19.5 mV after depositing tantalum oxide films. The in vitro results showed that the adhesion, proliferation, and osteogenic differentiation of rat bone marrow mesenchymal stem cells on modified Ti6Al4V scaffolds were significantly enhanced, which may be ascribed to surface structure optimization and the compatibility of tantalum oxide. This study provides a strategy to improve the cytocompatibility and osteogenic differentiation of porous Ti6Al4V scaffolds for orthopedic implants.

Three-Dimensional Scaffolds for Bone Tissue Engineering

Immobilization using external or internal splints is a standard and effective procedure to treat minor skeletal fractures. In the case of major skeletal defects caused by extreme trauma, infectious diseases or tumors, the surgical implantation of a bone graft from external sources is required for a complete cure. Practical disadvantages, such as the risk of immune rejection and infection at the implant site, are high in xenografts and allografts. Currently, an autograft from the iliac crest of a patient is considered the "gold standard" method for treating large-scale skeletal defects. However, this method is not an ideal solution due to its limited availability and significant reports of morbidity in the harvest site (30%) as well as the implanted site (5-35%). Tissue-engineered bone grafts aim to create a mechanically strong, biologically viable and degradable bone graft by combining a three-dimensional porous scaffold with osteoblast or progenitor cells. The materials used for such tissue-engineered bone grafts can be broadly divided into ceramic materials (calcium phosphates) and biocompatible/bioactive synthetic polymers. This review summarizes the types of materials used to make scaffolds for cryo-preservable tissue-engineered bone grafts as well as the distinct methods adopted to create the scaffolds, including traditional scaffold fabrication methods (solvent-casting, gas-foaming, electrospinning, thermally induced phase separation) and more recent fabrication methods (fused deposition molding, stereolithography, selective laser sintering, Inkjet 3D printing, laser-assisted bioprinting and 3D bioprinting). This is followed by a short summation of the current osteochondrogenic models along with the required scaffold mechanical properties for in vivo applications. We then present a few results of the effects of freezing and thawing on the structural and mechanical integrity of PLLA scaffolds prepared by the thermally induced phase separation method and conclude this review article by summarizing the current regulatory requirements for tissue-engineered products.

Calcium Phosphate Cements as Carriers of Functional Substances for the Treatment of Bone Tissue

Interest in calcium phosphate cements as materials for the restoration and treatment of bone tissue defects is still high. Despite commercialization and use in the clinic, the calcium phosphate cements have great potential for development. Existing approaches to the production of calcium phosphate cements as drugs are analyzed. A description of the pathogenesis of the main diseases of bone tissue (trauma, osteomyelitis, osteoporosis and tumor) and effective common treatment strategies are presented in the review. An analysis of the modern understanding of the complex action of the cement matrix and the additives and drugs distributed in it in relation to the successful treatment of bone defects is given. The mechanisms of biological action of functional substances determine the effectiveness of use in certain clinical cases. An important direction of using calcium phosphate cements as a carrier of functional substances is the volumetric incorporation of anti-inflammatory, antitumor, antiresorptive and osteogenic functional substances. The main functionalization requirement for carrier materials is prolonged elution. Various release factors related to the matrix, functional substances and elution conditions are considered in the work. It is shown that cements are a complex system. Changing one of the many initial parameters in a wide range changes the final characteristics of the matrix and, accordingly, the kinetics. The main approaches to the effective functionalization of calcium phosphate cements are considered in the review.

Physical Characteristics and Biocompatibility of 3D-Printed Polylactic-Co-Glycolic Acid Membranes Used for Guided Bone Regeneration

Bioresorbable polymeric membranes for guided bone regeneration (GBR) were fabricated using the three-dimensional printing technique. Membranes made of polylactic-co-glycolic acid (PLGA), which consist of lactic acid (LA) and glycolic acid in ratios of 10:90 (group A) and 70:30 (group B), were compared. Their physical characteristics including architecture, surface wettability, mechanical properties, and degradability were compared in vitro, and their biocompatibilities were compared in vitro and in vivo. The results demonstrated that the membranes of group B had mechanical strength and could support the proliferation of fibroblasts and osteoblasts significantly better than those of group A (p < 0.05). The degradation rate in Group B was significantly lower than that in Group A, but they significantly produced less acidic environment (p < 0.05). In vivo, the membranes of group B were compared with the commercially available collagen membranes (group C). The amount of newly formed bone of rat's calvarial defects covered with the membranes of group C was stable after week 2, whereas that of group B increased over time. At week 8, the new bone volumes in group B were greater than those in group C (p > 0.05). In conclusion, the physical and biological properties of the PLGA membrane (LA:GA, 70:30) were suitable for GBR.

Resorbable membrane design: In vitro characterization of silver doped-hydroxyapatite-reinforced XG/PEI semi-IPN composite

In this study, the production and characterization of silver-doped hydroxyapatite (AgHA) reinforced Xanthan gum (XG) and Polyethyleneimine (PEI) reinforced semi-interpenetrating polymer network (IPN) biocomposite, known to be used as bone cover material for therapeutic purposes in bone tissue, were performed. XG/PEI IPN films containing 2AgHA nanoparticles were produced by simultaneous condensation and ionic gelation. Characteristics of 2AgHA-XG/PEI nanocomposite film were evaluated by structural, morphological (SEM, XRD, FT-IR, TGA, TM, and Raman) and biological activity analysis (degradation, MTT, genotoxicity, and antimicrobial activity) techniques. In the physicochemical characterization, it was determined that 2AgHA nanoparticles were homogeneously dispersed in the XG/PEI-IPN membrane at high concentration and the thermal and mechanical stability of the formed film were high. The nanocomposites showed high antibacterial activity against Acinetobacter Baumannii (A.Baumannii), Staphylococcus aureus (S.aureus), and Streptococcus mutans (S.mutans). L929 exhibited good biocompatibility for fibroblast cells and was determined to support the formation of MCC cells. It was shown that a resorbable 2AgHA-XG/PEI composite material was obtained with a high degradation rate and 64% loss of mass at the end of the 7th day. Physico-chemically developed biocompatible and biodegradable XG-2AgHA/PEI nanocomposite semi-IPN films possessed an important potential for the treatment of defects in bone tissue as an easily applicable bone cover. Besides, it was noted that 2AgHA-XG/PEI biocomposite could increase cell viability, especially in dental-bone treatments for coating, filling, and occlusion.

A novel bioactive glass/graphene oxide composite coating for a polyether ether ketone-based dental implant

Polyether ether ketone (PEEK) is a biocompatible material that lacks antimicrobial activity and bioactivity; therefore, is not appropriate for use as a dental implant. To overcome these deficiencies, a novel composite coating of bioactive glass and graphene oxide was prepared. PEEK discs were polished, cleaned, and the surface treated with sulfuric acid for 15 min. The composite coating consisted of bioactive glass produced by the sol-gel route and doped with 0.75 wt% graphene oxide. X-ray diffraction, Fourier transform infrared spectroscopy, and scanning electron microscopy-energy dispersive spectroscopy analyses were employed to characterize the composite coating, and the coating adhesion strength quantified using a pull-off test. Cytotoxicity was assessed using osteoblast-like cells and gingival fibroblasts. The wettability of the coated and non-coated samples was determined by optical contact angle assessment, and bioactivity was assessed by immersion in simulated body fluid. The results revealed that the bioactive glass/graphene oxide composite coating, approximately 7 μm thick, was transparent, homogenous with few microcracks and microporosities, but adhered strongly and was not cytotoxic to either osteoblast-like cells or gingival fibroblasts. The wettability of the PEEK sample was increased to <20° after coating with the composite, and apatite formation was detectable after 14 days of immersion in simulated body fluid.

Titanium Surface-Grafted Zwitterionic Polymers with an Anti-Polyelectrolyte Effect Enhances Osteogenesis

Zwitterionic polymers have attracted considerable attention because of their anti-adsorption and unique anti-polyelectrolyte effects and was widely used in surface modification. In this study, zwitterionic copolymers (poly (sulfobetaine methacrylate-co-butyl acrylate) (pSB) coating on the surface of a hydroxylated titanium sheet using surface-initiated atom transfer radical polymerization (SI-ATRP) was successfully constructed. X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FT-IR) and Water contact angle (WCA) analysis proved the successful preparation of the coating. The swelling effect caused by the anti-polyelectrolyte effect was reflected in the simulation experiment in vitro, and this coating can promote the proliferation and osteogenesis of MC3T3-E1. Therefore, this study provides a new strategy for designing multifunctional biomaterials for implant surface modifications.

Geopolymer Materials for Bone Tissue Applications: Recent Advances and Future Perspectives

With progress in the bone tissue engineering (BTE) field, there is an important need to develop innovative biomaterials to improve the bone healing process using reproducible, affordable, and low-environmental-impact alternative synthetic strategies. This review thoroughly examines geopolymers' state-of-the-art and current applications and their future perspectives for bone tissue applications. This paper aims to analyse the potential of geopolymer materials in biomedical applications by reviewing the recent literature. Moreover, the characteristics of materials traditionally used as bioscaffolds are also compared, critically analysing the strengths and weaknesses of their use. The concerns that prevented the widespread use of alkali-activated materials as biomaterials (such as their toxicity and limited osteoconductivity) and the potentialities of geopolymers as ceramic biomaterials have also been considered. In particular, the possibility of targeting their mechanical properties and morphologies through their chemical compositions to meet specific and relevant requirements, such as biocompatibility and controlled porosity, is described. A statistical analysis of the published scientific literature is presented. Data on "geopolymers for biomedical applications" were extracted from the Scopus database. This paper focuses on possible strategies necessary to overcome the barriers that have limited their application in biomedicine. Specifically, innovative hybrid geopolymer-based formulations (alkali-activated mixtures for additive manufacturing) and their composites that optimise the porous morphology of bioscaffolds while minimising their toxicity for BTE are discussed.

Fabrication of polycaprolactone/calcium phosphates hybrid scaffolds impregnated with plant extracts using 3D printing for potential bone regeneration

The increase in critical bone diseases and defects in the world's population increases the need for bone substitutes to restore form and function. Organic and inorganic scaffolds with antibacterial properties could provide advantages for bone regeneration. In this study, we obtained scaffolds of polycaprolactone (PCL) charged with calcium phosphates nanoparticles and impregnated with extracts of Colombian plants as an alternative for potential bone regeneration. Calcium phosphate nanoparticles were obtained via auto-combustion synthesis. The nanoparticles were incorporated into the PCL with a chemical dissolution-disperse process. The composite obtained was used to produce a filament to print Triply Periodic Minimal Surface (TPMS) based scaffolds. Such geometry facilitates cellular growth thanks to its interconnected porosity. The scaffolds were impregnated with extracts of Justicia cf colorifera (Acanthaceae), and Billia rosea (Sapindaceae) due to their ancestral medical applications. A physical and biological characterization was conducted. The process to print scaffolds with an enhanced geometry to facilitate the flux of biological fluids was successful. The scaffolds loaded with B. rosea showed strong antibacterial behavior, suggesting the presence of reported terpenoids with antibacterial properties. The approach used in this study evidenced promising prospects for bone defect repair.

Novel Method for the Production of Titanium Foams to Reduce Stress Shielding in Implants

Titanium foams have potential applications in orthopedic and dental implants because of their low elastic modulus and good bone in-growth properties. In the present study, a novel method for the preparation of three-dimensional interconnected microporous titanium foams has been developed. This method is based on the insertion of a filler metal into the titanium metal by arc melting, followed by its removal by an electrochemical dealloying process for the development of foams. Complete removal of the filler metal by the electrochemical dealloying process was confirmed by an X-ray diffractometry (XRD) analysis, whereas scanning electron microscopy (SEM) analysis of the developed foams showed the development of interconnected porosity. Ti foams with different levels of porosities were successfully developed by varying the amount of the filler metal. Mechanical and thermal characterizations of the developed foams were carried out using compression testing and laser flash apparatus, respectively. The yield strength and elastic modulus of the developed foams were found to decrease by increasing the volume fraction of pores. The elastic modulus of the developed titanium foams (15.5-36 GPa) was found to be closer to that of human bones, whereas their yield strength (147-170 MPa) remained higher than that of human bones. It is therefore believed that the developed Ti foams can help in reducing the problem of stress shielding observed in orthopedic implants. The thermal diffusivity of the developed foams (4.3-0.69 mm²/s) was found to be very close to that of human dentine.

Identification and ranking biomaterials for bone scaffolds using machine learning and PROMETHEE

Purpose

Bones have a complex hierarchical structure that supports their diverse chemical, biological, and mechanical functions. High rates of bone susceptibility to fractures and injury have attracted extensive research interest to find alternate biomaterials for bone scaffolds. Natural bone healing is only successful if the defect is very small and when a defect exceeds 1 cm3 then bone grafting is required. Large bone defects or injuries are very serious problems in orthopedics as they bring great harm to health and normal function of daily life routine. A scaffold should have good strength to maintain its own structure after implantation in a load bearing environment and without being stiff that shields surrounding bone from the load. Therefore, mechanical properties of bone scaffolds should match those of the host tissue and should be part of the natural environment of the body without any harm or further damage.

Methods

In this paper, we present two main contributions. First, we investigate the use of machine learning models in identifying biomaterials that are suitable for bone scaffolds. Second, we rank the best materials for biomedical scaffold applications using the multi-criteria decision analysis methods, the Preference Ranking Organization METhod for the Enrichment of Evaluations (PROMETHEE). Machine learning models investigated are AdaBoost, artificial neural network (ANN), Naïve Bayes (NB), Decision tree (DT), Support Vector Machine (SVM), and K-Nearest Neighbor (KNN). Mechanical properties such as comprehensive strength, tensile strength, and Young’s modulus with the cortical bone are used as the standard reference for classification.

Results

The results show that the ANN outperforms the other machine learning models in identifying the biomaterials suitable for bone tissue engineering, while the ranking results using PROMETHEE show that Brushite and Titanium alloy are the best appropriate biomaterials for the cancellous and cortical bones, respectively.

Conclusion

Brushite and Titanium alloy are the best biomaterials for the cancellous and cortical bones, respectively.

A Novel Strategy for Liposomal Drug Separation in Plasma by TiO2 Microspheres and Application in Pharmacokinetics

Purpose

Liposomes are nano-scale materials with a biofilm-like structure. They have excellent biocompatibility and are increasingly useful in drug delivery systems. However, the in vivo fate of liposomal drugs is still unclear because existing bioanalytical methods for quantitation of total and liposomal-encapsulated drugs have limits. A novel strategy for liposomal-encapsulated drug separation from plasma was developed via the specific coordinate binding interaction of TiO₂ microspheres with the phosphate groups of liposomes.

Methods

Liposomal-encapsulated docetaxel was separated from plasma by TiO₂ microspheres and analyzed by the UPLC-MS/MS method. The amount of TiO₂, pH of the dilutions, plasma dilution factors and incubation time were optimized to improve extraction recovery. The characterization of the adsorption of liposome-encapsulated drugs by TiO₂ microspheres was observed by electron microscopy. For understanding the mechanism, pseudo-first and the pseudo-second order equations were proposed for the adsorption process. The study fully validated the method for quantitation of liposomal-encapsulated in plasma and the method was applied to the pharmacokinetic study of docetaxel liposomes.

Results

The encapsulated docetaxel had a concentration range of 15-4000 ng/mL from the plasma sample using a TiO₂ extraction method. Successful method validation proved the method was sensitive, selective and stable, and was suitable for quantitation of docetaxel liposomes in plasma samples. Extraction recovery of this method was higher than that of SPE method. As shown in electron microscopy, the liposomes adsorbed on TiO₂ microspheres were intact and there was no drug leakage. The study proposed pseudo-first and the pseudo-second order equations to facilitate the adsorption of liposomal drugs with TiO₂ microspheres. The proposed strategy supports the pharmacokinetic study of docetaxel liposomes in rats.

Conclusion

TiO₂ extraction method was stable, reproducible, and reliable for quantitation of encapsulated docetaxel. Because of versatility of lipids, it is expected to a universal bioanalysis method for the pharmacokinetic study of liposomes.

Biofabrication of Poly(glycerol sebacate) Scaffolds Functionalized with a Decellularized Bone Extracellular Matrix for Bone Tissue Engineering

The microarchitecture of bone tissue engineering (BTE) scaffolds has been shown to have a direct effect on the osteogenesis of mesenchymal stem cells (MSCs) and bone tissue regeneration. Poly(glycerol sebacate) (PGS) is a promising polymer that can be tailored to have specific mechanical properties, as well as be used to create microenvironments that are relevant in the context of BTE applications. In this study, we utilized PGS elastomer for the fabrication of a biocompatible and bioactive scaffold for BTE, with tissue-specific cues and a suitable microstructure for the osteogenic lineage commitment of MSCs. In order to achieve this, the PGS was functionalized with a decellularized bone (deB) extracellular matrix (ECM) (14% and 28% by weight) to enhance its osteoinductive potential. Two different pore sizes were fabricated (small: 100-150 μm and large: 250-355 μm) to determine a preferred pore size for in vitro osteogenesis. The decellularized bone ECM functionalization of the PGS not only improved initial cell attachment and osteogenesis but also enhanced the mechanical strength of the scaffold by up to 165 kPa. Furthermore, the constructs were also successfully tailored with an enhanced degradation rate/pH change and wettability. The highest bone-inserted small-pore scaffold had a 12% endpoint weight loss, and the pH was measured at around 7.14. The in vitro osteogenic differentiation of the MSCs in the PGS-deB blends revealed a better lineage commitment of the small-pore-sized and 28% (w/w) bone-inserted scaffolds, as evidenced by calcium quantification, ALP expression, and alizarin red staining. This study demonstrates a suitable pore size and amount of decellularized bone ECM for osteoinduction via precisely tailored PGS elastomer BTE scaffolds.

Immunomodulatory Blood-Derived Hybrid Hydrogels as Multichannel Microenvironment Modulators for Augmented Bone Regeneration

Autologous blood-derived protein hydrogels have shown great promise in the field of personalized regenerative medicine. However, the inhospitable regenerative microenvironments, especially the unfavorable immune microenvironment, are closely associated with their limited tissue-healing outcomes. Herein, novel immunomodulatory blood-derived hybrid hydrogels (PnP-iPRF) are rationally designed and constructed for enhanced bone regeneration via multichannel regulation of the osteogenic microenvironment. Such double-network hybrid hydrogels are composed of clinically approved injectable platelet-rich fibrin (i-PRF) and polycaprolactone/hydroxyapatite composite nanofibers by using enriched polydopamine (PDA) as the anchor. The polycaprolactone component in PnP-iPRF provides a reinforced structure to stimulate osteoblast differentiation in a proper biomechanical microenvironment. Most importantly, the versatile PDA component in PnP-iPRF can not only offer high adhesion capacity to the growth factors of i-PRF and create a suitable biochemical microenvironment for sustained osteogenesis but also reprogram the osteoimmune microenvironment via the induction of M2 macrophage polarization to promote bone healing. The present study will provide a new paradigm to realize enhanced osteogenic efficacy by multichannel microenvironment regulations and give new insights into engineering high-efficacy i-PRF hydrogels for regenerative medicine.

Strategies to improve bioactive and antibacterial properties of polyetheretherketone (PEEK) for use as orthopedic implants

Polyetheretherketone (PEEK) has gradually become the mainstream material for preparing orthopedic implants due to its similar elastic modulus to human bone, high strength, excellent wear resistance, radiolucency, and biocompatibility. Since the 1990s, PEEK has increasingly been used in orthopedics. Yet, the widespread application of PEEK is limited by its bio-inertness, hydrophobicity, and susceptibility to microbial infections. Further enhancing the osteogenic properties of PEEK-based implants remains a difficult task. This article reviews some modification methods of PEEK in the last five years, including surface modification of PEEK or incorporating materials into the PEEK matrix. For surface modification, PEEK can be modified by chemical treatment, physical treatment, or surface coating with bioactive substances. For PEEK composite material, adding bioactive filler into PEEK through the melting blending method or 3D printing technology can increase the biological activity of PEEK. In addition, some modification methods such as sulfonation treatment of PEEK or grafting antibacterial substances on PEEK can enhance the antibacterial performance of PEEK. These strategies aim to improve the bioactive and antibacterial properties of the modified PEEK. The researchers believe that these modifications could provide valuable guidance on the future design of PEEK orthopedic implants.

Biomimetic Self-Assembling Metal-Organic Architectures with Non-Iridescent Structural Coloration for Synergetic Antibacterial and Osteogenic Activity of Implants

Materials in nature feature versatile and programmable interactions to render macroscopic architectures with multiscale structural arrangements. By rationally combining metal-carboxylate and metal-organophosphate coordination interactions, Au₂₅(MHA)₁₈ (MHA, 6-mercaptohexanoic acid) nanocluster self-assembled structural color coating films and phytic acid (PA)-metal coordination complexes are sequentially constructed on the surface of titanium implants. The Lewis acid-base coordination principle applies for these metal-organic coordination networks. The isotropic arrangement of nanoclusters with a short-range order is investigated via grazing incidence wide-angle X-ray scattering. The integration of robust M-O (M = Ti, Zr, Hf) and labile Cu-O coordination bonds with high connectivity of Au₂₅(MHA)₁₈ nanoclusters enables these artificial photonic structures to achieve a combination of mechanical stability and bacteriostatic activity. Moreover, the colorless and transparent PA-metal complex layer allows the viewing of the structural color and surface wettability switching to hydrophilic and makes feasible the interfacial biomineralization of hydroxyapatite. Collectively, these modular metal-organic coordination-driven assemblies are predictive and rational material design strategies with tunable hierarchy and diversity. The complete metal-organic architectures will not only help improve the physicochemical properties of the bone-implant interface with synergistic antibacterial and osseointegration activities but also can boost surface engineering of medical metal implants.

Simultaneously stimulated osteogenesis and anti-bacteria of physically cross-linked double-network hydrogel loaded with MgO-Ag2O nanocomposites

Hydrogels, with a three-dimensional network of water-soluble polymer and water, could simulate the critical properties of extracellular matrix, which has been widely used in bone tissue engineering. However, most of conventional hydrogels for bone regeneration are fragile and have poor osteogenic activity, which restricts their applications. In this work, a novel nanoparticle-hydrogel composite consisting of physically cross-linked double-network loaded with MgO-Ag₂O nanocomposites was developed by the sol-gel method. The Mg²⁺ released from MgO-Ag₂O nanocomposites was used as an ionic cross-linking site of sodium alginate (SA), while the hydrophobic micelles in the polyacrylamide (PAAM) network is acted as another crosslinking point. The results indicated that the novel nanoparticle-hydrogel composites had good self-recovery ability and excellent mechanical properties compared with the conventional sodium alginate (SA)/polyacrylamide (PAAM) hydrogels. Additionally, it showed a slow release of Mg and Ag ions due to the dual function of the embedding effect of hydrogels and the increasing pH of the solution induced by the hydrolysis of sodium alginate. In terms of in vitro tests, the nanoparticle-hydrogel composites showed significantly stimulatory effects on the proliferation and differentiation of SaOS-2 cells. In addition, the antibacterial effects of the nanoparticle-hydrogel composites were gradually enhanced with the increase of MgO-Ag₂O content.

Femtosecond laser optimization of PEEK: efficient bioactivity achieved by synergistic surface chemistry and structures

Poly-ether-ether-ketone (PEEK) is considered a potential orthopedic material due to the excellent mechanical properties and chemical resistance, but its biological inertness hampers its further clinical application. In this study, advanced femtosecond laser microfabrication technology was utilized to induce the change of the surface characteristics of PEEK to improve its bioactivity. Meanwhile, the mechanism of surface reaction and improved bioactivity was interpreted in detail from the perspective of material science. The surface physical-chemical characterization results showed that femtosecond laser etching could increase the surface energy, and the contents of active sites including amorphous carbon and carbon-hydroxyl on PEEK surfaces. In vitro validation experiments demonstrated that the samples etched with a femtosecond laser had a better ability to induce apatite deposition and cell proliferation than those treated with popular sulfonation modification, which would lead to better bioactivity and osteointegration. The current work fully presents the mechanism of the femtosecond laser low-temperature plasma effect on PEEK and the resulting surface characteristics, which could broaden the application of PEEK in the orthopedic field. Moreover, it has great potential in the surface design and modification of other biomaterials with enhanced bioactivity.

Bioinspired Laminated Bioceramics with High Toughness for Bone Tissue Engineering

For the research of biomaterials in bone tissue engineering, it is still a challenge to fabricate bioceramics that overcome brittleness while maintaining the great biological performance. Here, inspired by the toughness of natural materials with hierarchical laminated structure, we presented a directional assembly-sintering approach to fabricate laminated MXene/calcium silicate-based (L-M/CS) bioceramics. Benefiting from the orderly laminated structure, the L-M/CS bioceramics exhibited significantly enhanced toughness (2.23 MPa·m^1/2) and high flexural strength (145 MPa), which were close to the mechanical properties of cortical bone. Furthermore, the L-M/CS bioceramics possessed more suitable degradability than traditional CaSiO₃ bioceramics due to the newly formed CaTiSiO₅ after sintering. Moreover, the L-M/CS bioceramics showed good biocompatibility and could stimulate the expression of osteogenesis-related genes. The mechanism of promoting osteogenic differentiation had been shown to be related to the Wnt signaling pathway. This work not only fabricated calcium silicate-based bioceramics with excellent mechanical and biological properties for bone tissue engineering but also provided a strategy for the combination of bionics and bioceramics.

A review on bioceramics scaffolds for bone defect in different types of animal models: HA and β -TCP

Increased life expectancy has led to an increase in the use of bone substitutes in numerous nations, with over two million bone-grafting surgeries performed worldwide each year. A bone defect can be caused by trauma, infections, and tissue resections which can self-heal due to the osteoconductive nature of the native extracellular matrix components. However, natural self-healing is time-consuming, and new bone regeneration is slow, especially for large bone defects. It also remains a clinical challenge for surgeons to have a suitable bone substitute. To date, there are numerous potential treatments for bone grafting, including gold-standard autografts, allograft implantation, xenografts, or bone graft substitutes. Tricalcium phosphate (TCP) and hydroxyapatite (HA) are the most extensively used and studied bone substitutes due to their similar chemical composition to bone. The scaffolds should be testedin vivoandin vitrousing suitable animal models to ensure that the biomaterials work effectively as implants. Hence, this article aims to familiarize readers with the most frequently used animal models for biomaterials testing and highlight the available literature for in vivo studies using small and large animal models. This review summarizes the bio ceramic materials, particularly HA and β-TCP scaffolds, for bone defects in small and large animal models. Besides, the design considerations for the pre-clinical animal model selection for bone defect implants are emphasized and presented.

A Review of Anodized TiNbSn Alloys for Improvement in Layer Quality and Application to Orthopedic Implants

Titanium alloys are useful for application in orthopedic implants. However, complications, such as prosthetic infections and aseptic loosening, often occur after orthopedic devices are implanted. Therefore, innovation in surface modification techniques is essential to develop orthopedic materials with optimal properties at the biomaterial–bone interface. In this review, we present recent research on the improvement in the osteoconductivity and antibacterial effect of the Ti-33.6% Nb-4% Sn (TiNbSn) alloy by anodic oxidation and other related studies. TiNbSn alloys are excellent new titanium alloys with a low Young’s modulus, high tensile strength, and with gradient functional properties such as a thermally adjustable Young’s modulus and strength. Titanium dioxide (TiO₂), when obtained by the anodic oxidation of a TiNbSn alloy, improves bone affinity and provides antibacterial performance owing to its photocatalytic activity. The safety of TiO₂ and its strong bonding with metal materials make its method of preparation a promising alternative to conventional methods for improving the surface quality of orthopedic implants. Implementing anodization technology for TiNbSn alloys may alleviate orthopedic surgery-related complications, such as loosening, stress shielding, and infection after arthroplasty.