Light quenching of pyridine2 fluorescence with time-delayed pulses

Spontaneous loss versus stimulation gain in pump-probe microscopy: a proof of concept demonstration

SIGNIFICANCE

The large background, narrow dynamic range, and detector saturation have been the common limiting factors in stimulated emission (SE)-based pump-probe microscopy, attributed to the very small signal overriding the very intense laser probe beam. To better differentiate the signal of interest from the background, lock-in detection is used to measure the fluorescence quenching, which is termed spontaneous loss (SL). The advantages are manifold. The spontaneous fluorescence signal can be well separated from both the pump and the probe beams with filters, thus eliminating the background, enlarging the dynamic range, and avoiding the saturation of the detector.

AIM

We propose and demonstrate an integrated pump-probe microscopy technique based on lock-in detection for background removal and dynamic range enhancement through SL detection.

APPROACH

The experimental setup is configured with a pulsed diode laser at a wavelength λpu  =  635  nm, acting as a pump (excitation) and a mode-locked Ti:sapphire laser at a central wavelength λpr  =  780  nm, serving as the probe beam (stimulation). Both pulse trains are temporally synchronized through high precision delay control by adjusting the length of the triggering cables. The pump and probe beams are alternatively modulated at different frequencies f1 and f2 to extract the stimulated gain (SG) and SL signal.

RESULTS

SG signal shows saturation due to the irradiation of the intense probe beam onto the photodetector. However, the detector saturation does not occur at high probe beam power for SL detection. The fluorescence lifetime images are acquired with reduced background. The theoretical signal-to-noise ratios for SG and SL are also estimated by photon statistics.

CONCLUSION

We have confirmed that the detection of SL allows the elimination of the large background without photodetector saturation, which commonly exists in SG configuration. This modality would allow unprecedented manipulation and investigation of fluorophores in fluorescence imaging.

Using Pyridinium Styryl Dyes as the Standards of Time-Resolved Instrument Response

In this paper, two pyridinium styryl dyes, [2-(4-dimethylamino-phenyl)-vinyl]-1-methylpyridinium iodide (DASPMI), were synthesized and characterized by steady state fluorescence spectroscopy as well as picosecond and femtosecond time-resolved fluorescence spectroscopies. Both dyes exhibit large Stokes shifts and fluorescence decays equivalent to the instrument response function (IRF) standards employed in time-correlated single-photon counting. Due to their styryl and pyridinium moieties, DASPMIs have higher peak fluorescence intensity and shorter excited-state lifetimes than iodide ion-quenched fluorophores. The fluorescence lifetimes of o-DASPMI and p-DASPMI were measured to be 6.6 ps and 12.4 ps, respectively. The fluorescence transients of these DASPMIs were used as the IRFs for iterative reconvolution fitting of the time-resolved fluorescence decay profiles of Rhodamine B (RhB), sulforhodamine B (SRB), and the SRB-SRB2m RNA aptamer complex. The quality of the fits employing the DASPMI-derived IRFs are consistently equivalent to those employing IRFs obtained from light scattering. These results indicate that DASPMI-derived IRFs may be suited for a broad range of applications in time-resolved spectroscopy and fluorescence lifetime imaging microscopy (FLIM), especially in the visible emission range.

Long working distance fluorescence lifetime imaging with stimulated emission and electronic time delay

In this work, long working distance fluorescence lifetime imaging is realized with stimulated emission in combination with electronic time delay control. Spatial coherence, as a result of stimulated emission, supports unattenuated fluorescence detection at extended distance, using low NA optics. An electronic time delayed trigger provides an advantageous way in adjusting the pulse separation and probing the fluorescence lifetime in the nanosecond ranges. The fluorescence lifetime of selected fluorophores is accurately determined through the pump-probe configuration. The characteristics and applications in fluorescence lifetime measurement of stimulated emission are investigated and summarized succinctly here.

Instrument response standard in time-resolved fluorescence

The fluorescence of LDS 798 dye in aqueous solution has a very short lifetime of 24 ps, independent of excitation wavelength. The time response of common photon counting detectors depends on the wavelength of the registered photon. In lifetime measurements, the instrument response function (IRF) is usually approximated by the temporal profile of the scattered excitation light. Because lambda(Exc) is typically much shorter than lambda(Em), a systematic error may be present in these measurements. We demonstrate that the fluorescence decay of LDS 798 is a better approximation of IRF, in particular, for avalanche photodiodes used in the near infrared spectral region.