The effect of process variables on the degradation and physical properties of spray dried insulin intended for inhalation

Impact of dry coating lactose as a brittle excipient on multi-component blend processability

Previous work demonstrated the benefits of dry coating fine-grade microcrystalline cellulose (MCC) for enabling direct compression (DC), a favored tablet manufacturing method, due to enhanced flowability while retaining good compactability of placebo and binary blends of cohesive APIs. Here, fine brittle excipients, Pharmatose 450 (P450, 19 μm) and Pharmatose 350 (P350, 29 μm), having both poor flowability and compactability are dry coated with silica A200 or R972P to assess DC capability of multi-component cohesive API (coarse acetaminophen, 22 μm, and ibuprofen50, 47 μm) blends. Dry coated P450 and P350 not only attained excellent flowability and high bulk density but also heightened tensile strength hence processability, which contrasts with reported reduction for dry coated ductile MCC. Although hydrophobic R972P imparted better flowability, hydrophilic A200 better enhanced tensile strength, hence selected for dry coating P450 in multi-component blends that included fine Avicel PH-105. For coarse acetaminophen blends, substantial bulk density and flowability increase without any detrimental effect on tensile strength were observed; a lesser amount of dry coated P450 was better. Increased flowability, bulk density, and tensile strength, hence enhanced processability by reaching DC capability, were observed for 60 wt% ibuprofen50, using only 18 wt% of the dry coated P450, i.e. 0.18 wt% silica in the blend.

Customizable Resveratrol Spray-dried Micro-composites for Inhalation as a Promising Contender for Treatment of Idiopathic Pulmonary Fibrosis

The past decades have witnessed tremendous expansion in utilization of plant-derived medicines as resveratrol (RES) in treating several diseases like idiopathic pulmonary fibrosis (IPF). RES can exhibit its role in treating IPF via its outstanding antioxidant and anti-inflammatory activities. The goal of this work was to formulate RES-loaded spray-dried composite microparticles (SDCMs) suitable for pulmonary delivery via dry powder inhaler (DPI). They were prepared by spray drying of a previously prepared RES-loaded bovine serum albumin nanoparticles (BSA NPs) dispersion using different carriers. RES-loaded BSA NPs, prepared by the desolvation technique, acquired suitable particle size of 177.67±0.95 nm and entrapment efficiency of 98.7±0.35% with perfectly uniform size distribution and high stability. Considering the attributes of the pulmonary route, NPs were co-spray dried with compatible carriers viz. mannitol, dextran, trehalose, leucine, glycine, aspartic acid, and glutamic acid to fabricate SDCMs. All formulations showed suitable mass median aerodynamic diameter less than 5 µm; that is suitable for deep lung deposition. However, the best aerosolization behavior was attained from using leucine with fine particle fraction (FPF) of 75.74%, followed by glycine with FPF of 54.7%. Finally, a pharmacodynamic study was conducted on bleomycin-induced mice, and it strongly revealed the role of the optimized formulations in alleviating PF through suppressing the levels of hydroxyproline, tumor necrosis factor-α and matrix metalloproteinase-9 with obvious improvements in the treated lung histopathology. These findings indicate that in addition to leucine, the glycine amino acid, which is not commonly used yet, is very promising in the formulation of DPIs.

Combining Isolation-Free and Co-processing Manufacturing Approaches to Access Room Temperature Ionic Liquid Forms of APIs

The addition of non-active components at the point of active pharmaceutical ingredient (API) isolation by means of co-processing is an attractive approach for improving the material properties of APIs. Simultaneously, there is increased interest in the pharmaceutical industry in continuous manufacturing processes. These often consist of liquid feeds which maintain materials in solution and mean that solids handling is avoided until the final step. Such techniques enable new forms of APIs to be used in final dosage forms which have been overlooked due to unfavourable material properties. API-based ionic liquids (API-ILs) are an example of a class of compounds that exhibit exceptional solubility and stability qualities at the cost of their physical characteristics. API-ILs could benefit from isolation-free manufacturing in combination with co-processing approaches to circumvent handling issues and make them viable routes to formulating poorly soluble APIs. However, API-ILs are most commonly synthesised via a batch reaction that produces an insoluble solid by-product. To avoid this, an ion exchange resin protocol was developed to enable the API-IL to be synthesised and purified in a single step, and also produce it in a liquid effluent that can be integrated with other unit operations. Confined agitated bed crystallisation and spray drying are examples of processes that have been adapted to produce or consume liquid feeds and were combined with the ion exchange process to incorporate the API-IL synthesis into isolation-free frameworks and continuous manufacturing streams. This combination of isolation-free and co-processing techniques paves the way towards end-to-end continuous manufacturing of API-IL drug products.

Optimization of Spray Drying Process Parameters for the Preparation of Inhalable Mannitol-Based Microparticles Using a Box-Behnken Experimental Design

Inhalation is used for local therapy of the lungs and as an alternative route for systemic drug delivery. Modern powder inhalation systems try to target the required site of action/absorption in the respiratory tract. Large porous particles (LPPs) with a size >5 μm and a low mass density (usually measured as bulk or tapped) of <0.4 g/cm³ can avoid protective lung mechanisms. Their suitable aerodynamic properties make them perspective formulations for deep lung deposition. This experiment studied the effect of spray-drying process parameters on LPP properties. An experimental design of twelve experiments with a central point was realized using the Box-Behnken method. Three process parameters (drying temperature, pump speed, and air speed) were combined on three levels. Particles were formed from a D-mannitol solution, representing a perspective material for lung microparticles. The microparticles were characterized in terms of physical size (laser diffraction), aerodynamic diameter (aerodynamic particle sizer), morphology (SEM), and densities. The novelty and main goal of this research were to describe how the complex parameters of the spray-drying process affect the properties of mannitol LPPs. New findings can provide valuable data to other researchers, leading to the easy tuning of the properties of spray-dried particles by changing the process setup.

Impact of dispersion media and carrier type on spray-dried proliposome powder formulations loaded with beclomethasone dipropionate for their pulmonary drug delivery via a next generation impactor

Drug delivery via aerosolization for localized and systemic effect is a non-invasive approach to achieving pulmonary targeting. The aim of this study was to prepare spray-dried proliposome (SDP) powder formulations to produce carrier particles for superior aerosolization performance, assessed via a next generation impactor (NGI) in combination with a dry powder inhaler. SDP powder formulations (F1-F10) were prepared using a spray dryer, employing five different types of lactose carriers (Lactose monohydrate (LMH), lactose microfine (LMF), lactose 003, lactose 220 and lactose 300) and two different dispersion media. The first dispersion medium was comprised of water and ethanol (50:50% v/v ratio), and the second dispersion medium comprised wholly of ethanol (100%). In the first dispersion medium, the lipid phase (consisting of Soya phosphatidylcholine (SPC as phospholipid) and Beclomethasone dipropionate (BDP; model drug) were dissolved in ethanol and the lactose carrier in water, followed by spray drying. Whereas in second dispersion medium, the lipid phase and lactose carrier were dispersed in ethanol only, post spray drying. SDP powder formulations (F1-F5) possessed significantly smaller particles (2.89 ± 1.24-4.48 ± 1.20 μm), when compared to SDP F6-F10 formulations (10.63 ± 3.71-19.27 ± 4.98 μm), irrespective of lactose carrier type via SEM (scanning electron microscopy). Crystallinity of the F6-F10 and amorphicity of F1-F15 formulations were confirmed by XRD (X-ray diffraction). Differences in size and crystallinity were further reflected in production yield, where significantly higher production yield was obtained for F1-F5 (74.87 ± 4.28-87.32 ± 2.42%) then F6-F10 formulations (40.08 ± 5.714-54.98 ± 5.82%), irrespective of carrier type. Negligible differences were noted in terms of entrapment efficiency, when comparing F1-F5 SDP formulations (94.67 ± 8.41-96.35 ± 7.93) to F6-F10 formulations (78.16 ± 9.35-82.95 ± 9.62). Moreover, formulations F1-F5 demonstrated significantly higher fine particle fraction (FPF), fine particle dose (FPD) and respirable fraction (RF) (on average of 30.35%, 890.12 μg and 85.90%) when compared to counterpart SDP powder formulations (F6-F10). This study has demonstrated that when a combination of water and ethanol was employed as dispersion medium (formulations F1-F5), superior formulation properties for pulmonary drug delivery were observed, irrespective of carrier type employed.

Optimization of Astaxanthin Recovery in the Downstream Process of Haematococcus pluvialis

Astaxanthin derived from Haematococcus pluvialis is a valuable metabolite applied in a wide range of products. Its extraction depends on a sophisticated series of downstream process steps, including harvesting, disruption, drying, and extraction, of which some are dependent on each other. To determine the processes that yield maximum astaxanthin recovery, bead milling, high-pressure homogenization, and no disruption of H. pluvialis biomass were coupled with spray-drying, vacuum-drying, and freeze-drying in all possible combinations. Eventually, astaxanthin was extracted using supercritical CO2. Optimal conditions for spray-drying were evaluated through the design of experiments and standard least squares regression (feed rate: 5.8 mL/min, spray gas flow: 400 NL/h, inlet temperature: 180 °C). Maximal astaxanthin recoveries were yielded using high-pressure homogenization and lyophilization (85.4%). All combinations of milling or high-pressure homogenization and lyophilization or spray-drying resulted in similar recoveries. Bead milling and spray-drying repeated with a larger spray-dryer resulted in similar astaxanthin recoveries compared with the laboratory scale. Smaller astaxanthin recoveries after the extraction of vacuum-dried biomass were mainly attributed to textural changes. Evaluation of these results in an economic context led to a recommendation for bead milling and spray-drying prior to supercritical CO2 extraction to achieve the maximum astaxanthin recoveries.

State-of-the-Art Review of The Application and Development of Various Methods of Aerosol Therapy

Aerosol therapy is a rapidly developing field of science. Due to a number of advantages, the administration of drugs to the body with the use of aerosol therapy is becoming more and more popular. Spraying drugs into the patient's lungs has a significant advantage over other methods of administering drugs to the body, including injection and oral methods. In order to conduct proper and effective aerosol therapy, it is necessary to become familiar with the basic principles and applications of aerosol therapy under various conditions. The effectiveness of inhalation depends on many factors, but most of all on: the physicochemical properties of the sprayed system, the design of the medical inhaler and its correct application, the dynamics of inhalation (i.e. the frequency of breathing and the volume of inhaled air). It is worth emphasizing that respiratory system diseases are one of the most frequently occurring and fastest growing diseases in the world. Accordingly, in recent years, a significant increase in the number of new spraying devices and pharmaceutical drugs for spraying has appeared on the market. It should also be remembered that the process of spraying a liquid is a complicated and complex process, and its efficiency is very often characterized by the use of micro- and macro parameters (including average droplet diameters or the spectrum of droplet diameter distribution). In order to determine the effectiveness of the atomization process and in the delivery of drugs to the patient's respiratory tract, the analysis of the size of the generated aerosol droplets is most often performed. Based on the proposed literature review, it has been shown that many papers dealt with the issues related to aerosol therapy, the selection of an appropriate spraying device, the possibility of modifying the spraying devices in order to increase the effectiveness of inhalation, and the possibility of occurrence of certain discrepancies resulting from the use of various measurement methods to determine the characteristics of the generated aerosol. The literature review presented in the paper was prepared in order to better understand the spraying process. Moreover, it can be helpful in choosing the right medical inhaler for a given liquid with specific rheological properties. The experimental data contained in this study are of great cognitive importance and may be of interest to entities involved in pharmaceutical product engineering (in particular in the case of the production of drugs containing liquids with complex rheological properties).

A Design of Experiment Approach to Optimize Spray-Dried Powders Containing Pseudomonas aeruginosaPodoviridae and Myoviridae Bacteriophages

In the present study, we evaluated the effect of spray-drying formulations and operating parameters of a laboratory-scale spray-dryer on the characteristics of spray-dried powders containing two Pseudomonas aeruginosa bacteriophages exhibiting different morphotypes: a podovirus (LUZ19) and a myovirus (14-1). We optimized the production process for bacteriophage-loaded powders, with an emphasis on long-term storage under ICH (international conference on harmonization) conditions. D-trehalose-/L-isoleucine-containing bacteriophage mixtures were spray-dried from aqueous solutions using a Büchi Mini Spray-dryer B-290 (Flawil, Switzerland). A response surface methodology was used for the optimization of the spray-drying process, with the following as-evaluated parameters: Inlet temperature, spray gas flow rate, and the D-trehalose/L-isoleucine ratio. The dried powders were characterized in terms of yield, residual moisture content, and bacteriophage lytic activity. L-isoleucine has demonstrated a positive impact on the activity of LUZ19, but a negative impact on 14-1. We observed a negligible impact of the inlet temperature and a positive correlation of the spray gas flow rate with bacteriophage activity. After optimization, we were able to obtain dry powder preparations of both bacteriophages, which were stable for a minimum of one year under different ICH storage conditions (up to and including 40 °C and 75% relative humidity).

Stress Factors in Protein Drug Product Manufacturing and Their Impact on Product Quality

Injectable protein-based medicinal products (drug products, or DPs) must be produced by using sterile manufacturing processes to ensure product safety. In DP manufacturing the protein drug substance, in a suitable final formulation, is combined with the desired primary packaging (e.g., syringe, cartridge, or vial) that guarantees product integrity and enables transportation, storage, handling and clinical administration. The protein DP is exposed to several stress conditions during each of the unit operations in DP manufacturing, some of which can be detrimental to product quality. For example, particles, aggregates and chemically-modified proteins can form during manufacturing, and excessive amounts of these undesired variants might cause an impact on potency or immunogenicity. Therefore, DP manufacturing process development should include identification of critical quality attributes (CQAs) and comprehensive risk assessment of potential protein modifications in process steps, and the relevant steps must be characterized and controlled. In this commentary article we focus on the major unit operations in protein DP manufacturing, and critically evaluate each process step for stress factors involved and their potential effects on DP CQAs. Moreover, we discuss the current industry trends for risk mitigation, process control including analytical monitoring, and recommendations for formulation and process development studies, including scaled-down runs.

Spray Freeze Dried Lyospheres® for Nasal Administration of Insulin

Pharmacologically active macromolecules, such as peptides, are still a major challenge in terms of designing a delivery system for their transport across absorption barriers and at the same time provide sufficiently high long-term stability. Spray freeze dried (SFD) lyospheres^® are proposed here as an alternative for the preparation of fast dissolving porous particles for nasal administration of insulin. Insulin solutions containing mannitol and polyvinylpyrrolidone complemented with permeation enhancing excipients (sodium taurocholate or cyclodextrins) were sprayed into a cooled spray tower, followed by vacuum freeze drying. Final porous particles were highly spherical and mean diameters ranged from 190 to 250 µm, depending on the excipient composition. Based on the low density, lyospheres resulted in a nasal deposition rates of 90% or higher. When tested in vivo for their glycemic potential in rats, an insulin-taurocholate combination revealed a nasal bioavailability of insulin of 7.0 ± 2.8%. A complementary study with fluorescently labeled-dextrans of various molecular weights confirmed these observations, leading to nasal absorption ranging from 0.7 ± 0.3% (70 kDa) to 10.0 ± 3.1% (4 kDa). The low density facilitated nasal administration in general, while the high porosity ensured immediate dissolution of the particles. Additionally, due to their stability, lyospheres provide an extremely promising platform for nasal peptide delivery.

Stability of lyophilized and spray dried vaccine formulations

Liquid formulations of vaccines are subject to instabilities that result from degradation processes that proceed via a variety of physical and chemical pathways. In dried formulations, such as those prepared by lyophilization or spray drying, many of these degradation pathways may be avoided or inhibited. Thus, the stability of vaccine formulations can be enhanced significantly in the absence of bulk water. Potential advantages of dry vaccine formulations include extended shelf lives and less stringent cold-chain storage requirements, both of which offer possibilities of reduced vaccine wastage and facilitated distribution to resource-poor areas. Lyophilization and spray drying represent the most common methods of stabilizing vaccines through drying. This article reviews several lyophilized and spray dried vaccines that address a diverse set of pathogens, as well as some of the assays used to quantify their stability. Recent dry vaccine trends include needle-free delivery of dry powder via non-parenteral routes of administration and the incorporation of advanced vaccine adjuvants into formulations, which further contribute to the goal of increasing vaccine distribution to resource-poor areas. Challenges associated with development of these newer technologies are also discussed.

Inhaled RNA Therapeutics for Obstructive Airway Diseases: Recent Advances and Future Prospects

Obstructive airway diseases, e.g., chronic obstructive pulmonary disease (COPD) and asthma, represent leading causes of morbidity and mortality worldwide. However, the efficacy of currently available inhaled therapeutics is not sufficient for arresting disease progression and decreasing mortality, hence providing an urgent need for development of novel therapeutics. Local delivery to the airways via inhalation is promising for novel drugs, because it allows for delivery directly to the target site of action and minimizes systemic drug exposure. In addition, novel drug modalities like RNA therapeutics provide entirely new opportunities for highly specific treatment of airway diseases. Here, we review state of the art of conventional inhaled drugs used for the treatment of COPD and asthma with focus on quality attributes of inhaled medicines, and we outline the therapeutic potential and safety of novel drugs. Subsequently, we present recent advances in manufacturing of thermostable solid dosage forms for pulmonary administration, important quality attributes of inhalable dry powder formulations, and obstacles for the translation of inhalable solid dosage forms to the clinic. Delivery challenges for inhaled RNA therapeutics and delivery technologies used to overcome them are also discussed. Finally, we present future prospects of novel inhaled RNA-based therapeutics for treatment of obstructive airways diseases, and highlight major knowledge gaps, which require further investigation to advance RNA-based medicine towards the bedside.

Peptide Isolation via Spray Drying: Particle Formation, Process Design and Implementation for the Production of Spray Dried Glucagon

PURPOSE

Spray drying plays an important role in the pharmaceutical industry for product development of sensitive bio-pharmaceutical formulations. Process design, implementation and optimisation require in-depth knowledge of process-product interactions. Here, an integrated approach for the rapid, early-stage spray drying process development of trehalose and glucagon on lab-scale is presented.

METHODS

Single droplet drying experiments were used to investigate the particle formation process. Process implementation was supported using in-line process analytical technology within a data acquisition framework recording temperature, humidity, pressure and feed rate. During process implementation, off-line product characterisation provided additional information on key product properties related to residual moisture, solid state structure, particle size/morphology and peptide fibrillation/degradation.

RESULTS

A psychrometric process model allowed the identification of feasible operating conditions for spray drying trehalose, achieving high yields of up to 84.67%, and significantly reduced levels of residual moisture and particle agglomeration compared to product obtained during non-optimal drying. The process was further translated to produce powders of glucagon and glucagon-trehalose formulations with yields of >83.24%. Extensive peptide aggregation or degradation was not observed.

CONCLUSIONS

The presented data-driven process development concept can be applied to address future isolation problems on lab-scale and facilitate a systematic implementation of spray drying for the manufacturing of sensitive bio-pharmaceutical formulations.

Spray drying as an advantageous strategy for enhancing pharmaceuticals bioavailability

Spray drying is an efficient technique that is used not only for rapid evaporation of the solvent from different systems but also for designing ultra-fine particles with various desirable characteristics. The obtained powders demonstrate reasonably narrow size distribution with a submicron-to-micron size range. It is one of the recent techniques applied to present acceptable solutions to enhance the absorption and bioavailability of some challenging drugs. In view of that, the purpose of this review is to shed some light on the wide variety of the recently developed fine particulate products that can be produced from spray-drying technique. This article reports the most outstanding advantages and challenges that could be overcome by exploiting the spray-drying technique for the production of different pharmaceuticals, including pure drug particles and drug-loaded polymeric carriers. The potential of this technique, whether used alone or in combination with other methods, in order to develop reproducible and scalable procedures for the best translation of bench-to-bedside innovation of pharmaceutical products is hereby discussed.

Effect of Spray Drying on Amorphization of Indomethacin Nicotinamide Cocrystals; Optimization, Characterization, and Stability Study

Cocrystals have gained a lot of consideration regarding its superior role in enhancement of solubility and dissolution of the included API. Cocrystals could be converted to coamorphous systems via different techniques like milling and quench cooling; however, the use of spray-drying technique has not been investigated before. So, the aim of this study was to explore the effect of spray drying on the amorphization of indomethacin/nicotinamide, INDNIC, as model cocrystals. Spray-drying operating parameters were optimized using the Taguchi design of experiment for maximum powder yield and low moisture content. The obtained INDNIC spray-dried cocrystals were characterized for their degree of crystallinity, morphology, moisture content, and dissolution performance. In addition, stability study was performed at different temperature and humidity conditions. Experimental design results delineate that spray-drying inlet temperature and cocrystal concentrations as the most influential factors for maximum powder yield and low moisture content. Powder X-ray diffraction and differential scanning calorimetry studies revealed the conversion of INDNIC cocrystals to a partial coamorphous or coamorphous structure without dissociation of INDNIC molecular structure. INDNIC coamorphous powders showed a significantly higher release of IND compared with cocrystals and remain physically stable for 2 months when stored in the refrigerator.

Spray congealed solid lipid microparticles as a sustained release delivery system for Gonadorelin [6-D-Phe]: Production, optimization and in vitro release behavior

Sustained release lipid microparticles for a potential veterinary application were produced by the means of spray congealing using saturated triglycerides with respective surfactants. The spray congealing process was optimized using unloaded and loaded microparticles, revealing the highest impact of the spray flow on material loss. Yield could be optimized by increasing the spray flow as well as a reduction of the melt temperature from 90 to 75 °C. For the delivery system developed in this study, a release of around 15 days was targeted. The release profile was in first hand determined with the use of model substances (aspartame and tryptophan), before incorporating the decapeptide Gonadorelin [6-D-Phe]. Release could be controlled between 2 and 28 d, which was dependent on stability of microparticles upon incubation, type and concentration of emulsifier, as well as the used triglyceride. Differential scanning calorimetry and X-ray powder diffraction confirmed the crystallization behavior of C14 and C16-triglycerides in combination with various emulsifiers in different modification without impact on release.

Micelles entrapped microparticles technology: a novel approach to resolve dissolution and bioavailability problems of poorly water soluble drugs

Aim: Aim of this study was to design a solid oral delivery system for a weakly basic drug such as dasatinib (DAS), so as to achieve pH-independent dissolution and improved oral bioavailability.Methods: DAS was solubilised using sodium lauryl sulphate as an aqueous micellar system and such a system containing lactose monohydrate as carrier was spray-dried to obtain a solid mass. Subsequently, the DAS-solid was converted into a tablet using conventional tableting methods.Results: The dissolution study revealed pH-independent dissolution over a wide range of pH conditions. An in vivo bioavailability testing on rats revealed an improved C_max and AUC_0-24. Similarly, viability assay showed a better inhibitory effect of spray-dried dasatinib over the DAS.Conclusions: Micellar solubilisation and spray-drying technology can be approached to resolve poor dissolution and bioavailability of drugs belonging to biopharmaceutical classification system II and III. This technology is amenable to scale-up and has commercial potential.

Influence of Composition and Spray-Drying Process Parameters on Carrier-Free DPI Properties and Behaviors in the Lung: A review

Although dry powder inhalers (DPIs) have attracted great interest compared to nebulizers and metered-dose inhalers (MDIs), drug deposition in the deep lung is still insufficient to enhance therapeutic activity. Indeed, it is estimated that only 10–15% of the drug reaches the deep lung while 20% of the drug is lost in the oropharyngeal sphere and 65% is not released from the carrier. The potentiality of the powders to disperse in the air during the patient’s inhalation, the aerosolization, should be optimized. To do so, new strategies, in addition to classical lactose-carrier, have emerged. The lung deposition of carrier-free particles, mainly produced by spray drying, is higher due to non-interparticulate forces between the carrier and drug, as well as better powder uniformity and aerosolization. Moreover, the association of two or three active ingredients within the same powder seems easier. This review is focused on a new type of carrier-free particles which are characterized by a sugar-based core encompassed by a corrugated shell layer produced by spray drying. All excipients used to produce such particles are dissected and their physico-chemical properties (Péclet number, glass transition temperature) are put in relation with the lung deposition ability of powders. The importance of spray-drying parameters on powders’ properties and behaviors is also evaluated. Special attention is given to the relation between the morphology (characterized by a corrugated surface) and lung deposition performance. The understanding of the closed relation between particle material composition and spray-drying process parameters, impacting the final powder properties, could help in the development of promising DPI systems suitable for local or systemic drug delivery.

Spray-dried alginate microparticles for potential intranasal delivery of ropinirole hydrochloride: development, characterization and histopathological evaluation

Ropinirole hydrochloride (RH) is an anti-Parkinson drug with relativity low oral bioavailability owing to its extensive hepatic first pass metabolism. Spray-dried mucoadhesive alginate microspheres of RH were developed and characterized followed by histopathological evaluation using nasal tissue isolated from sheep. Spherical microparticles having high product yield (around 70%) were obtained when the inlet temperature of spray drying was 140 °C. Fourier Transform Infrared (FTIR) studies revealed the compatibility of the drug with the polymer, and scanning electron microscopy (SEM) showed that drug-loaded microparticles were spherical, and the apparent surface roughness was inversely related to the ratio of polymer to drug. Furthermore, size of the spray-dried particles were in the range of 2.5-4.37 µm, depending on formulation. All formulations had high drug encapsulation efficiencies (101-106%). Drug loaded into the polymeric particles was in the amorphous state and drug molecules were molecularly dispersed in the polymeric matrix of the microparticles which were revealed by X-ray diffraction and differential scanning calorimetry (DSC), respectively. The in vitro drug release was influenced by polymer concentration. Histopathological study demonstrated that RH-loaded sodium alginate microparticles was safe to nasal epithelium. In conclusion, spray drying of RH using sodium alginate polymer has produced microparticles of suitable characteristics for potential intranasal administration.

Pulmonary delivery of Nanocomposite Microparticles (NCMPs) incorporating miR-146a for treatment of COPD

The treatment and management of COPD by inhalation to the lungs has emerged as an attractive alternative route to oral dosing due to higher concentrations of the drug being administered to site of action. In this study, Nanocomposite Microparticles (NCMPs) of microRNA (miR-146a) containing PGA-co-PDL nanoparticles (NPs) for dry powder inhalation were formulated using l-leucine and mannitol. The spray-drying (Buchi B290) process was optimised and used to incorporate NPs into NCMPs using mix of l-leucine and mannitol excipients in different ratios (F1; 100:0% w/w, F2; 75:25% w/w, F3; 50:50% w/w, F4; 25:75% w/w, F5; 0:100% w/w) to investigate yield %, moisture content, aerosolisation performance and miR-146a biological activity. The optimum condition was performed at feed rate 0.5 ml/min, aspirator rate 28 m³/h, atomizing air flow rate 480 L/h, and inlet drying temperature 70 °C which produced highest yield percentage and closest recovered NPs size to original prior spray-drying. The optimum formulation (F4) had a high yield (86.0 ± 15.01%), recovered NPs size after spray-drying 409.7 ± 10.05 nm (initial NPs size 244.8 ± 4.40 nm) and low moisture content (2.02 ± 0.03%). The aerosolisation performance showed high Fine Particle Fraction (FPF) 51.33 ± 2.9%, Emitted Dose (ED) of 81.81 ± 3.0%, and the mass median aerodynamic diameter (MMAD) was ≤5 µm suggesting a deposition in the respirable region of the lungs. The biological activity of miR-146a was preserved after spray-drying process and miR-146a loaded NCMPs produced target genes IRAK1 and TRAF6 silencing. These results indicate the optimal process parameters for the preparation of NCMPs of miR-146a-containing PGA-co-PDL NPs suitable for inhalation in the treatment and management of COPD.

A Design of Experiment (DoE) approach to optimise spray drying process conditions for the production of trehalose/leucine formulations with application in pulmonary delivery

The present study evaluates the effect of L-leucine concentration and operating parameters of a laboratory spray dryer on characteristics of trehalose dry powders, with the goal of optimizing production of these powders for inhaled drug delivery. Trehalose/L-leucine mixtures were spray dried from aqueous solution using a laboratory spray dryer. A factorial design of experiment (DoE) was undertaken and process parameters adjusted were: inlet temperature, gas flow rate, feed solution flow rate (pump setting), aspiration setting and L-leucine concentration. Resulting powders were characterised in terms of particle size, yield, residual moisture content, and glass transition temperature. Particle size was mainly influenced by gas flow rate, whereas product yield and residual moisture content were found to be primarily affected by inlet temperature and spray solution feed rate respectively. Interactions between a number of different process parameters were elucidated, as were relationships between different responses. The leucine mass ratio influenced the physical stability of powders against environmental humidity, and a high leucine concentration (30% w/w) protected amorphous trehalose from moisture induced crystallization. High weight ratio of leucine in the formulation, however, negatively impacted the aerosol performance. Thus, in terms of L-leucine inclusion in a formulation designed for pulmonary delivery, a balance needs to be found between physical stability and deposition characteristics.

Optimization of spray drying parameters and food additives to reduce glycation using response surface methodology in powdered infant formulas

The heat-based spray drying process generating the highest level of advanced glycation end-products (AGEs) in the infant formula processing was set as a control point from which the levels of AGE markers, N-carboxymethyllysine, 5-hydroxymethylfurfural, and fluorescence intensity, can be mitigated. We optimized the parameters, including inlet temperature, feeding rate, and aspirator rate during spray drying, and alternatively optimized food additives, including pyridoxine hydrochloride, dl-α-tocopheryl acetate, and l-carnitine. Using response surface methodology, the optimal condition based on our experimental condition for the inlet temperature, pump rate, and aspirator rate were 148.7 °C, 342.4 mL/h and 28.6 m³/h, respectively, and the optimal conditions of pyridoxine hydrochloride, dl-α-tocopheryl acetate and l-carnitine were 0.99 mg/100 g dry mass (DM), 8 mg/100 g DM and 20.4 mg/100 g DM, respectively. These results suggest that AGEs can be mitigated by controlling the parameters and optimizing the addition of food additives during the spray-drying process.

Optimization of Ciprofloxacin Hydrochloride Spray-Dried Microparticles for Pulmonary Delivery Using Design of Experiments

Ciprofloxacin is a broad-spectrum antibiotic for treatment of pulmonary diseases such as chronic obstructive pulmonary disease and cystic fibrosis. The purpose of this work was to rationally study the spray drying of ciprofloxacin in order to identify the formulation and operating conditions that lead to a product with aerodynamic properties appropriate for dry powder inhalation. A 2^4 - 1 fractional factorial design was applied to investigate the effect of selected variables (i.e., ciprofloxacin hydrochloride (CIP) concentration, drying air inlet temperature, feed flow rate, and atomization air flow rate) on several product and process parameters (i.e., particle size, aerodynamic diameter, moisture content, densities, porosity, powder flowability, outlet temperature, and process yield) and to determine an optimal condition. The studied factors had a significant effect on the evaluated responses (higher p value 0.0017), except for the moisture content (p value > 0.05). The optimal formulation and operating conditions were as follows: CIP concentration 10 mg/mL, drying air inlet temperature 110°C, feed volumetric flow rate 3.0 mL/min, and atomization air volumetric flow rate 473 L/h. The product obtained under this set had a particle size that guarantees access to the lung, a moisture content acceptable for dry powder inhalation, fair flowability, and high process yield. The PDRX and SEM analysis of the optimal product showed a crystalline structure and round and dimpled particles. Moreover, the product was obtained by a simple and green spray drying method.

Developments in the formulation and delivery of spray dried vaccines

Spray drying is a promising method for the stabilization of vaccines, which are usually formulated as liquids. Usually, vaccine stability is improved by spray drying in the presence of a range of excipients. Unlike freeze drying, there is no freezing step involved, thus the damage related to this step is avoided. The edge of spray drying resides in its ability for particles to be engineered to desired requirements, which can be used in various vaccine delivery methods and routes. Although several spray dried vaccines have shown encouraging preclinical results, the number of vaccines that have been tested in clinical trials is limited, indicating a relatively new area of vaccine stabilization and delivery. This article reviews the current status of spray dried vaccine formulations and delivery methods. In particular it discusses the impact of process stresses on vaccine integrity, the application of excipients in spray drying of vaccines, process and formulation optimization strategies based on Design of Experiment approaches as well as opportunities for future application of spray dried vaccine powders for vaccine delivery.

Electrohydrodynamic atomization and spray-drying for the production of pure drug nanocrystals and co-crystals

In recent years, nanotechnology has offered attractive opportunities to overcome the (bio)pharmaceutical drawbacks of most drugs such as low aqueous solubility and bioavailability. Among the numerous methodologies that have been applied to improve drug performance, a special emphasis has been made on those that increase the dissolution rate and the saturation solubility by the reduction of the particle size of pure drugs to the nanoscale and the associated increase of the specific surface area. Different top-down and bottom-up methods have been implemented, each one with its own pros and cons. Over the last years, the latter that rely on the dissolution of the drug in a proper solvent and its crystallization or co-crystallization by precipitation in an anti-solvent or, conversely, by solvent evaporation have gained remarkable impulse owing to the ability to adjust features such as size, size distribution, morphology and to control the amorphous/crystalline nature of the product. In this framework, electrohydrodynamic atomization (also called electrospraying) and spray-drying excel due to their simplicity and potential scalability. Moreover, they do not necessarily require suspension stabilizers and dry products are often produced during the formation of the nanoparticles what ensures physicochemical stability for longer times than liquid products. This review overviews the potential of these two technologies for the production of pure drug nanocrystals and co-crystals and discusses the recent technological advances and challenges for their implementation in pharmaceutical research and development.

Effect of drying parameters on the physical, morphological and thermal properties of spray-dried inulin

This study focuses on the thermal, morphological and physical properties of spray-dried chicory root inulin using a thermogravimetric analyzer, environmental scanning electron microscopy, X-ray diffractogram and modulated differential scanning calorimetry. Different spray-drying conditions were investigated by varying inlet temperature, outlet temperature and aspirator speed. The starting material was semicrystalline. A feed temperature of 95°C was employed, which produced a completely transparent solution for spray drying. At that particular temperature, the powder samples obtained were entirely amorphous and morphology resembled each other except for higher solid content. The low glass transition temperature (T g) (106.83°C) was evident by treating low-molecular-weight samples, whereas high-molecular-weight samples exhibited high T g (125.81°C). The semicrystalline samples due to the high concentration and milky dispersion exhibited high decomposition temperature. The feed temperature, molecular weight and concentration of the samples tend to have a significant effect on the properties of spray-dried inulin.

Effect of electrospinning process variables on the size of polymer fibers and bead-on-string structures established with a 23 factorial design

This work examines the effect of selected process parameters on the diameter of uniform and heterogeneous fibers (with and without bead-on-string structures) and the size of beads obtained during the electrospinning process. A 2³ factorial design was performed to determine the influence of the following factors: electrical voltage, flow rate and dynamic viscosity of the poly(vinylpyrrolidone) ethanolic solution. Factorial design enables the analysis of the mathematical relationship between the chosen factors and the response with a minimum number of experiments. The factor having the most significant impact on the size of beaded fibers and beads was the solution viscosity, while the voltage had the greatest influence on the bead-free fiber diameter. The interactions between the studied factors were also analyzed. It was found that the presented method can be used for the design of an optimal and cost-effective electrospinning process, allowing the desired product to be obtained with expected features.

Dry powder aerosols to co-deliver antibiotics and nutrient dispersion compounds for enhanced bacterial biofilm eradication

The purpose of this study was to formulate a dry powder for inhalation containing a combination treatment for eradication of Pseudomonas aeruginosa bacterial biofilms. Dry powders containing an antibiotic (ciprofloxacin hydrochloride, CH) and nutrient dispersion compound (glutamic acid, GA) at a ratio determined to eliminate the biofilms were generated by spray drying. Leucine was added to the spray dried formulation to aid powder flowability. A central composite design of experiments was performed to determine the effects of solution and processing parameters on powder yield and aerodynamic properties. Combinations of CH and GA eradicated bacterial biofilms at lower antibiotic concentrations compared to CH alone. Spray dried powders were produced with yields up to 43% and mass mean aerodynamic diameters (MMAD) in the respirable range. Powder yield was primarily affected by variables that determine cyclone efficiency, i.e. atomizer and solution flow rates and solution concentration; while MMAD was mainly determined by solution concentration. Fine particle fractions (FPF)<4.46μm and <2.82μm of the powders ranged from 56 to 70% and 35 to 46%, respectively. This study demonstrates that dry powder aerosols containing high concentrations of a combination treatment effective against P. aeruginosa biofilms could be developed with high yield, aerodynamic properties appropriate for inhalation, and no loss of potency.

Melatonin-loaded chitosan/Pluronic® F127 microspheres as in situ forming hydrogel: An innovative antimicrobial wound dressing

The aim of this study was to develop melatonin-loaded chitosan based microspheres as dry powder formulation suitable for wound dressing, rapidly forming hydrogel in contact with wound exudate. Microspheres were produced by spray-drying method. Fractional factorial design was employed to elucidate the effect of formulation and process parameters (feed flow rate, inlet air temperature, chitosan concentration, chitosan/melatonin ratio and chitosan/Pluronic® F127 ratio) on the product characteristics related to process applicability (production yield, entrapment efficiency and product moisture content) and microsphere performance in biological environment (microsphere mean diameter and surface charge). Appropriate formulation and process parameters for the establishment of efficient drying process resulting in fine-tuned chitosan and chitosan/Pluronic® F127 microspheres (efficient melatonin encapsulation, small diameter positive surface charge and low moisture content) were identified. Microspheres were characterized by appropriate flowability and high rate and extent of fluid uptake. Incorporation of Pluronic® F127 in microsphere matrix resulted in high melatonin amorphization and consequent higher melatonin release rate. Entrapment of melatonin in chitosan/Pluronic® F127 microspheres has potentiated chitosan antimicrobial activity against Staphylococcus aureus and five clinical isolates S. aureus MRSA strains. Microspheres were shown to be biocompatible with skin keratinocytes and fibroblasts at concentrations relevant for antimicrobial activity against planktonic bacteria.

Spray drying formulation of amorphous solid dispersions

Spray drying is a well-established manufacturing technique which can be used to formulate amorphous solid dispersions (ASDs) which is an effective strategy to deliver poorly water soluble drugs (PWSDs). However, the inherently complex nature of the spray drying process coupled with specific characteristics of ASDs makes it an interesting area to explore. Numerous diverse factors interact in an inter-dependent manner to determine the final product properties. This review discusses the basic background of ASDs, various formulation and process variables influencing the critical quality attributes (CQAs) of the ASDs and aspects of downstream processing. Also various aspects of spray drying such as instrumentation, thermodynamics, drying kinetics, particle formation process and scale-up challenges are included. Recent advances in the spray-based drying techniques are mentioned along with some future avenues where major research thrust is needed.

Revealing facts behind spray dried solid dispersion technology used for solubility enhancement

Poor solubility and bioavailability of an existing or newly synthesized drug always pose challenge in the development of efficient pharmaceutical formulation. Numerous technologies can be used to improve the solubility and among them amorphous solid dispersion based spray drying technology can be successfully useful for development of product from lab scale to commercial scale with a wide range of powder characteristics. Current review deals with the importance of spray drying technology in drug delivery, basically for solubility and bioavailability enhancement. Role of additives, selection of polymer, effect of process and formulation parameters, scale up optimization, and IVIVC have been covered to gain the interest of readers about the technology. Design of experiment (DoE) to optimize the spray drying process has been covered in the review. A lot more research work is required to evaluate spray drying as a technology for screening the right polymer for solid dispersion, especially to overcome the issue related to drug re-crystallization and to achieve a stable product both in vitro and in vivo. Based on the recent FDA recommendation, the need of the hour is also to adopt Quality by Design approach in the manufacturing process to carefully optimize the spray drying technology for its smooth transfer from lab scale to commercial scale.

Advantages and challenges of the spray-drying technology for the production of pure drug particles and drug-loaded polymeric carriers

Spray-drying is a rapid, continuous, cost-effective, reproducible and scalable process for the production of dry powders from a fluid material by atomization through an atomizer into a hot drying gas medium, usually air. Often spray-drying is considered only a dehydration process, though it also can be used for the encapsulation of hydrophilic and hydrophobic active compounds within different carriers without substantial thermal degradation, even of heat-sensitive substances due to fast drying (seconds or milliseconds) and relatively short exposure time to heat. The solid particles obtained present relatively narrow size distribution at the submicron-to-micron scale. Generally, the yield% of spray-drying at laboratory scale with conventional spray-dryers is not optimal (20-70%) due to the loss of product in the walls of the drying chamber and the low capacity of the cyclone to separate fine particles (<2 μm). Aiming to overcome this crucial drawback in early development stages, new devices that enable the production of submicron particles with high yield, even for small sample amounts, have been introduced into the market. This review describes the most outstanding advantages and challenges of the spray-drying method for the production of pure drug particles and drug-loaded polymeric particles and discusses the potential of this technique and the more advanced equipment to pave the way toward reproducible and scalable processes that are critical to the bench-to-bedside translation of innovative pharmaceutical products.