Metal composition of layered double hydroxides (LDHs) regulating ClO(-)4 adsorption to calcined LDHs via the memory effect and hydrogen bonding

Synthesis of bifunctional nanostructured adsorbents based on anionic/cationic clays: effect of arrangement on simultaneous adsorption of cadmium and arsenate

The development of bifunctional hybrid materials based on natural clays and layered double hydroxide (LDH) and their application on the simultaneous adsorption of Cd(II) and As(V) was investigated in this work. Two different synthesis routes, in situ and assembly, were employed to obtain the hybrid materials. Three types of natural clays, namely bentonite (B), halloysite (H), and sepiolite (S), were used in the study. These clays are characterized by a laminar, tubular, and fibrous structural arrangement, respectively. The physicochemical characterization results indicate that the hybrid materials were formed through interactions between the Al-OH and Si-OH groups present in the natural clays, and the Mg-OH and Al-OH groups present in the LDH for both synthesis routes. However, the "in situ" route yields a more homogenous material because the LDH formation is performed on the natural clay surface. The hybrid materials showed an anion and cation exchange capacity up to 200.7 meq/100 g and an isoelectric point near 7. The arrangement of natural clay has no impact on the properties of hybrid material but influences the adsorption capacity. The adsorption of Cd(II) onto hybrid materials was enhanced in comparison with natural clays, obtaining adsorption capacities of 80, 74, 65, and 30 mg/g for 15:1 (LDH:H)INSITU, 1:1 (LDH:S)INSITU, 1:1 (LDH:B)INSITU, and 1:1 (LDH:H)INSITU, respectively. The adsorption capacities of hybrid materials to adsorb As(V) were between 20 and 60 μg/g. The 15:1 (LDH:H)INSITU sample showed the best adsorption capacity being ten folds greater than halloysite and LDH. In all cases, the hybrid materials showed a synergistic effect for Cd(II) and As(V) adsorption. The adsorption study of Cd(II) onto hybrid materials showed that the primary adsorption mechanism is cation exchange between the interlayer cations in natural clay and Cd(II) in the aqueous solution. The adsorption of As(V) showed that the adsorption mechanism is attributed to anion exchange between CO23- in the interlayer space of LDH and H2ASO4- in the solution. The simultaneous adsorption of As (V) and Cd (II) shows that, during the As(V) adsorption, there is no competition by the adsorption sites. Still, the adsorption capacity towards Cd(II) was enhanced 1.2-folds. This study ultimately revealed that the arrangement of clay has a significant influence on the adsorption capacity of the hybrid material. This can be attributed to the similar morphology between the hybrid material and natural clays, as well as the important diffusion effects observed in the system.

NiFe Layered Double Hydroxides with Controlled Composition and Morphology for the Efficient Removal of Cr(VI) from Water

A layered double hydroxide (LDH) composed of Ni2+ and Fe3+ with a Fe3+/(Ni2+ + Fe3+) ratio of 0.05, which is not commonly available, was successfully prepared by coprecipitation from an aqueous solution of glycerol containing nickel nitrate and iron nitrate. Precipitation using NaOH as a precipitating agent at room temperature or 120 °C under hydrothermal conditions gave products with micrometer-sized aggregates of nanometer-sized unshaped particles, while that using urea yielded LDHs with a foam-like porous architecture composed of platy particles with a size of 100-300 nm. The products were examined to remove Cr(VI) from an acidic (pH = 3) aqueous solution of K2Cr2O7 by adsorption and photocatalytic reduction. The foam-like porous NiFe-LDH exhibited the highest adsorbed amount (122 mg g-1) and rate (0.017 g mg-1 min-1) in the dark and the highest rate (0.012 min-1) of photocatalytic Cr(VI) reduction among the NiFe-LDHs prepared in the present study, which can be explained as a positive effect of the foam-like porous architecture. These performances were superior to those of other reported LDHs, showing the importance of the composition and the particle morphology to boost the removal of Cr(VI).

Hydrochar-nanoparticle integration for arsenic removal from wastewater: Challenges, possible solutions, and future horizon

Arsenic (As) contamination poses a significant threat to human health, ecosystems, and agriculture, with levels ranging from 12 to 75% attributed to mine waste and stream sediments. This naturally element is abundant in Earth's crust and gets released into the environment through mining and rock processing, causing ≈363 million people to depend on As-contaminated groundwater. To combat this issue, introducing a sustainable hydrochar system has achieved a remarkable removal efficiency of over 92% for arsenic through adsorption. This comprehensive review presents an overview of As contamination in the environment, with a specific focus on its impact on drinking water and wastewater. It delves into the far-reaching effects of As on human health, ecosystems, aquatic systems, and agriculture, while also exploring the effectiveness of existing As treatment systems. Additionally, the study examines the potential of hydrochar as an efficient adsorbent for As removal from water/wastewater, along with other relevant adsorbents and biomass-based preparations of hydrochar. Notably, the fusion of hydrochar with nanoparticle-centric approaches presents a highly promising and environmentally friendly solution for achieving the removal of As from wastewater, exceeding >99% efficiency. This innovative approach holds immense potential for advancing the realms of green chemistry and environmental restoration. Various challenges associated with As contamination and treatment are highlighted, and proposed solutions are discussed. The review emphasizes the urgent need to advance treatment technologies, improve monitoring methods, and enhance regulatory frameworks. Looking outlook, the article underscores the importance of fostering research efforts, raising public awareness, and fostering interdisciplinary collaboration to address this critical environmental issue. Such efforts are vital for UN Sustainable Development Goals, especially clean water and sanitation (Goal 6) and climate action (Goal 13), crucial for global sustainability.

Layered Double Hydroxide/Graphene Quantum Dots as a New Sorbent for the Dispersive Solid-Phase Microextraction of Selected Benzophenones, Phenols, and Parabens

In this study, the synthesis of a layered double hydroxide (LDH) composite with graphene quantum dots (GQDs) and its utilization for the development of a dispersive solid-phase extraction procedure are described. To this end, a carbonate-free Mg-Al LDH was synthesized. The development of the composite material made feasible the use of GQDs in a sample preparation procedure, while the incorporation of the GQDs in the LDH structure resulted in an 80% increase in extraction efficiency, compared to the bare LDH. As a proof of concept, the composite material was used for the development of an analytical method for the extraction, and preconcentration, of benzophenones, phenols, and parabens in lake water using high-performance liquid chromatography, coupled to a diode array detector. The analytical method exhibits low limits of quantification (0.10-1.33 μg L^-1), good recoveries (92-100%), and satisfactory enrichment factors (169-186). Due to the abovementioned merits, the easy synthesis and simple extraction, the developed method can be used for the routine analysis of the target compounds.

Coating layered double hydroxides with carbon dots for highly efficient removal of multiple dyes

Layered double hydroxides (LDHs) and layered double oxides (LDOs) are desirable adsorption materials for printing and wastewater treatment owing to their outstanding anion exchange abilities, abundant active sites, and eco-friendly nature. In this study, a versatile LDO hybrid coated with carbon dots (CDs@MgAl-LDO) was constructed by modifying sodium dodecylbenzene sulfonate on the surface of MgAl-LDH as a carbon precursor, followed by ligand carbonization and hydrotalcite dehydration at 450 °C under N₂ flow. CDs@MgAl-LDO displayed a hexagonal lamellar architecture with a plate lateral size of approximately 500 nm. It had a higher BET specific surface area (28.61 m²/g) than MgAl-LDO (11.48 m²/g). X-ray diffraction analysis revealed that CDs@MgAl-LDO maintained the "memory effect" of LDOs and could retrieve the original structure when dispersed in water. Moreover, the modified carbon dots change the intrinsically hydrophilic nature of LDOs and help to improve the affinity for organic contaminants, including both cationic and anionic dyes. The adsorption of dyes on CDs@MgAl-LDO followed a pseudo-second-order kinetic model with correlation coefficients (R²) ranging from 0.9901 to 0.9911 and exhibited Freundlich-type heterogeneous adsorption. It showed superior adsorption performance for three dyes, with the maximum adsorption capacity of 3628.9-5174.1 mg/g, thereby outperforming previously reported LDH-based adsorbents. This work developed a facile approach for preparing new carbon dots-LDH hybrids for the highly efficient removal of multiple dyes.

β-Cyclodextrin-Calcium Complex Intercalated Hydrotalcites as Efficient Catalyst for Transesterification of Glycerol

β-cyclodextrin derivative intercalated MgAl-hydrotalcites (β-CD-Ca/LDH) was synthesized to convert glycerol into high value-added glycerol carbonate(GC) by transesterification of dimethyl carbonate (DMC) and glycerol in this paper. β-cyclodextrin-metal complexes and β-CD-Ca/LDH was characterized by XRD, FT-IR, SEM, XPS and nitrogen adsorption-desorption. The enrichment of organic reactants in the hydrophobic cavity of β-cyclodextrin improved the collision probability of reactants. The intercalation of β-cyclodextrin-calcium complex (β-CD-Ca) increased the pore size and basic strength of catalyst. The experiment results showed that the glycerol conversion was 93.7% and the GC yield was 91.8% catalyzed by β-CD-Ca/LDH when the molar ratio of DMC and glycerol was 3:1, the catalyst dosage was 4 wt.%, the reaction temperature was 75 °C and the reaction time was 100 min while the glycerol conversion was 49.4% and the GC yield was 48.6% catalyzed by MgAl-LDH under the same conditions.

Simultaneous Elimination of Dyes and Antibiotic with a Hydrothermally Generated NiAlTi Layered Double Hydroxide Adsorbent

In this study, a hydrothermal route was used to design a novel NiAlTi layered double hydroxide. The material so-obtained was characterized using various physiochemical techniques such as X-ray diffraction, Fourier transform infrared spectroscopy, thermogravimetric analysis for structural analysis, scanning electron microscopy, transmission electron microscopy for morphological analysis, and so on. The material so-obtained was further applied for wastewater remediation and was found to be an efficient, cost-effective, and reusable adsorbent. Organic contaminants such as dyes and antibiotics were used as pollutants to carry out the removal study. NiAlTi LDH was found to be an excellent adsorbent for the removal of anionic dyes and antibiotics. Excellent performance was shown by NiAlTi LDH at a broad pH range from 4 to 10 for anionic dyes (orange II and methyl orange), but tetracycline removal was predominantly maximum at pH = 9. Further, the kinetic studies also revealed that the adsorption process of both organic contaminants obeyed a pseudo-second-order model. In addition, the Langmuir isotherm adsorption model fitted the experimental results for both types of pollutants very well. The attained maximum adsorption capacity was superb for both organic dyes and antibiotics (1250 mg/g for MO, 2000 mg/g for OII, and 238.09 mg/g for TC). NiAlTi LDH was also capable of simultaneous elimination from a mixture of antibiotics and dyes. Further, NiAlTi LDH also showed outstanding stability and reusability, making it one of the most promising materials for large-scale wastewater remediation contaminated by dyes and antibiotics.

Hexavalent chromium removal from aqueous solution by adsorption on modified zeolites coated with Mg-layered double hydroxides

In this study, MgAl-LDHs and MgFe-LDHs were synthesized via co-precipitation method and in situ coated on pre-washed zeolites through dipping process in beaker. The obtained modified zeolites and original zeolites were utilized as substrates of constructed rapid infiltration systems (CRIS) to remove hexavalent chromium (Cr(VI)) in wastewater. Micro-morphology features and chemical composition of zeolites before and after modification were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), and X-ray fluorescence spectrometer (XRF). The SEM, XRD, and XRF results demonstrated the feasibility of LDHs coated on the surface of the original zeolites. Purification experiments in simulated CRIS showed that the Cr(VI) removal rates of zeolites/MgAl-LDHs increased by 110.03% on average every concentration (0.5-16 mg L^-1) compared with the original zeolites under 24-h HRT. The adsorption capacity of zeolites/MgAl-LDHs reached 66.98 mg kg^-1 at 32 mg L^-1 initial Cr(VI) concentration, which is nearly twice that of the original zeolites (33.24 mg kg^-1) and 1.5 times higher than that of zeolites/MgFe-LDHs (42.01 mg kg^-1). Isothermal adsorption tests showed that the Freundlich isotherm equations gave better fitting to the adsorption process. And zeolites/MgAl-LDHs showed a best fit with pseudo-second-order model which meant that the adsorption of Cr(VI) by zeolites/MgAl-LDHs was dominated by chemisorption. Thermodynamic parameters showed that the process of adsorption for the three substrates was spontaneous and endothermic intrinsically. Zeolites/MgAl-LDHs also displayed nearly 60% desorption rate with low concentration eluent (0.01 mol L^-1 NaCl). Therefore, zeolites/MgAl-LDHs were chosen out as an optimal substrate for removing Cr(VI) from wastewater in CRIS. Graphical Abstract.

A New Approach for Removing Anionic Organic Dyes from Wastewater Based on Electrostatically Driven Assembly

A conceptually new approach for an efficient removal of anionic organic dyes from wastewater using layered double hydroxides (LDHs) through their formation is presented. Acid yellow 25 (AY25) was used as anionic organic dye model molecules. As a result of the electrostatic induction, the removal mechanism involved a concurrent incorporation of AY25 molecules into the interlayer of LDHs during their structural arrangement, where Mg(2+) and Al(3+) ions were utilized to construct the base of LDHs in an alkaline solution. It was found that the molar stoichiometry of all precursors was a key factor affecting the removal efficiency. Within 5 min removal time, this method still maintained high removal efficiency of over 97% and provided a removal capacity of ∼186 mg g(-1), comparable to that of other LDH-based methods. Also, almost complete dye recovery was simply achieved by anionic exchange with common anions (Cl(-), NO3(-), and CO3(2-)). Additionally, the present technique is straightforward, cost-effective, and environmentally friendly since it avoids the synthesis step of sorbents, thus significantly saving time, chemicals, and energy. Hence, this strategy not only exhibits the alternative exploitation of LDHs, but also provides new insights into the removal of contaminants from wastewater.

Use of Mg-Al oxide for boron removal from an aqueous solution in rotation: Kinetics and equilibrium studies

Mg-Al oxide prepared through the thermal treatment of [Formula: see text] intercalated Mg-Al layered double hydroxides (CO3·Mg-Al LDH) was found to remove boron (B) from an aqueous solution. B was removed by the rehydration of Mg-Al oxide accompanied by combination with [Formula: see text] . When using twice the stoichiometric quantity of Mg-Al oxide for Mg/Al = 4, the residual concentration of B dropped from 100 to 2.8 mg/L in 480 min, and for Mg/Al = 2, it decreased from 100 to 2.5 mg/L in 240 min. In both cases, the residual concentration of B was highlighted to be lower than the current Japanese effluent standards (10 mg/L). The removal of B can be explained by way of pseudo-first-order reaction kinetics. The apparent activation energy of 63.5 kJ mol(-1), calculated from the Arrhenius plot indicating that a chemical reaction dominates the removal of B by Mg-Al oxide (Mg/Al = 2). The adsorption of B acts upon a Langmuir-type phenomena. The maximum adsorption (qm) and equilibrium adsorption constants (KL) were 7.4 mmol g(-1) and 1.9 × 10(3), respectively, for Mg-Al oxide (Mg/Al = 2). [Formula: see text] in B(OH)4·Mg-Al LDH produced by the removal of B was observed to undergo anion exchange with [Formula: see text] in solution. Following regeneration, the Mg-Al oxide maintained the ability to remove B from an aqueous solution. This study has clarified the possibility of recycling Mg-Al oxide for B removal.

Inorganic nanolayers: structure, preparation, and biomedical applications

Hydrotalcite-like compounds are two-dimensional inorganic nanolayers also known as clay minerals or anionic clays or layered double hydroxides/layered hydroxy salts, and have emerged as a single type of material with numerous biomedical applications, such as drug delivery, gene delivery, cosmetics, and biosensing. Inorganic nanolayers are promising materials due to their fascinating properties, such as ease of preparation, ability to intercalate different type of anions (inorganic, organic, biomolecules, and even genes), high thermal stability, delivery of intercalated anions in a sustained manner, high biocompatibility, and easy biodegradation. Inorganic nanolayers have been the focus for researchers over the last decade, resulting in widening application horizons, especially in the field of biomedical science. These nanolayers have been widely applied in drug and gene delivery. They have also been applied in biosensing technology, and most recently in bioimaging science. The suitability of inorganic nanolayers for application in drug delivery, gene delivery, biosensing technology, and bioimaging science makes them ideal materials to be applied for theranostic purposes. In this paper, we review the structure, methods of preparation, and latest advances made by inorganic nanolayers in such biomedical applications as drug delivery, gene delivery, biosensing, and bioimaging.

The co-adsorption of Cu2+ and Zn2+ with adsorption sites surface-lattice reforming on calcined layered double hydroxides

The picture shows that how the CLDHs recover into the hydrotalcite structure in the process of adsorption of Cu²⁺ and Zn²⁺.

Layered double hydroxide-carbon dot composite: high-performance adsorbent for removal of anionic organic dye

It would be of significance to design a green composite for efficient removal of contaminants. Herein, we fabricated a facile and environmentally friendly composite via direct assembly of surface passivated carbon dots with abundant oxygen-containing functional groups on the surface of the positively charged layered double hydroxide (LDH). The resulting LDH-carbon dot composites were characterized by X-ray diffraction (XRD), Fourier transformed infrared (FTIR) spectroscopy, high resolution transmission electron microscopy (HRTEM), scanning electron microscopy (SEM), and N2 adsorption-desorption technique. The adsorption performances of the resulting LDH-carbon dot composites were evaluated for the removal of anionic methyl blue dye. Taking advantage of the combined benefits of LDH and carbon dots, the as-prepared composites exhibited high uptake capability of methyl blue (185 mg/g). The adsorption behavior of this new adsorbent fitted well with Langmuir isotherm and the pseudo-second-order kinetic model. The reasons for the excellent adsorption capacity of methyl blue on the surface of the LDH-carbon dot hybrid were further discussed. A probable mechanism was speculated to involve the cooperative contributions of hydrogen bonding between methyl blue and carbon dots and electrostatic attraction between methyl blue and LDH, in the adsorption process. This work is anticipated to open up new possibilities in fabricating LDH-carbon dot materials in dealing with anionic dye pollutants.