Thermal induced EPR signals in tooth enamel

EPR dosimetry with tooth enamel: A review

When tooth enamel is exposed to ionizing radiation, radicals are formed, which can be detected using electron paramagnetic resonance (EPR) techniques. EPR dosimetry using tooth enamel is based on the (presumed) correlation between the intensity or amplitude of some of the radiation-induced signals with the dose absorbed in the enamel. In the present paper a critical review is given of this widely applied dosimetric method. The first part of the paper is fairly fundamental and deals with the main properties of tooth enamel and some of its model systems (e.g., synthetic apatites). Considerable attention is also paid to the numerous radiation-induced and native EPR signals and the radicals responsible for them. The relevant methods for EPR detection, identification and spectrum analyzing are reviewed from a general point of view. Finally, the needs for solid-state modelling and studies of the linearity of the dose response are investigated. The second part is devoted to the practical implementation of EPR dosimetry using enamel. It concerns specific problems of preparation of samples, their irradiation and spectrum acquisition. It also describes how the dosimetric signal intensity and dose can be retrieved from the EPR spectra. Special attention is paid to the energy dependence of the EPR response and to sources of uncertainties. Results of and problems encountered in international intercomparisons and epidemiological studies are also dealt with. In the final section the future of EPR dosimetry with tooth enamel is analyzed.

The mechanism of CO2- radical formation in biological and synthetic apatites

Biological apatites (tooth enamel, bone) and their synthetic analogues were exposed to gamma rays, UV light, or thermal treatment and studied by electron paramagnetic resonance (EPR). The thermal generation of CO2- radicals in synthetic apatite was observed for the first time. It was shown that the experimental EPR spectra of all of the above-mentioned materials are caused by the contribution of two types of CO2- radicals: axial and orthorhombic. The ratio of their concentrations depends on the characteristic energy of the external influence (i.e., the energy of quantum for radiation or kT for thermal treatment) and also on the quality of the initial material (defectiveness). Based on the analysis of EPR spectra recorded immediately after gamma-irradiation, the authors conclude that the main short-lived radical in bioapatites is CO3(3)- . The unified mechanism of CO2- radical formation in hydroxyapatites at different external influences is proposed; the main stages of transformation are CO3(2)- + e --> CO3(3)- --> CO2-, where the electron (e) originates from the ionization of impurities by radiation/temperature.

Dental enamel EPR dosimetry: comparative testing of the spectra processing methods for determination of radiation-induced signal amplitude

The aim of this investigation is to find out the optimal algorithm for mathematical processing of the EPR spectra of irradiated tooth enamel for estimating the amplitude of the radiation-induced signal, which is used for determination of the absorbed dose in enamel for retrospective individual dosimetry. A recently developed analytical model, which takes into account the line shape variation of the enamel EPR spectral components registered at different microwave power, was applied to spectra processing in various operation modes to simulate spectra processing techniques differing by the number of fitted parameters. The precision of dose determination at spectra processing was assessed by the root mean square deviation between experimental and nominal doses for sets of spectra of enamel samples irradiated in different doses and measured at different microwave power. It is shown that in the case of pooled enamel samples prepared as a mixture from different teeth, the higher precision of spectra processing is obtained using a model with fixed native background signal line shape (characterized by width and asymmetry parameters). In case of individual samples prepared each from a different tooth, better results are obtained using a model with variable background signal line shape.

The effect of heating on background and radiation-induced EPR signals in tooth enamel

The presented study is a continuation of our work performed during participation in the Third International Intercomparison on EPR Tooth Dosimetry. During the process of samples preparation, all 22 enamel samples were accidentally exposed for about 30 min to 150 degrees C temperature. This considerably affected shape of their EPR spectra mainly due to substantial increase in the background signal, which approximately doubled its contribution to the spectra. These effects were studied closer under controlled conditions of the delivered dose and heating temperature using another enamel samples. The observed changes in the spectra shape partially faded within a few days after heating. The heating resulted also in a noticeable generation of a spectral component similar to the dosimetric signal induced in enamel by radiation. The temperature-induced dosimetric component in EPR spectra of the heated samples remained constant for 32 days. Deviations in calculated contributions of the dosimetric signal into total EPR spectra of irradiated sample varied from -12 to +15% of its initial contribution in the non-heated enamel, depending on type of the background spectrum applied in numerical processing of the spectra.

Mechanically induced EPR signals in tooth enamel

Sample preparation of tooth enamel for electron paramagnetic resonance (EPR) dosimetry usually involves mechanical operations. The present study shows that mechanical operations performed without water cooling generate a paramagnetic center inducing a stable isotropic EPR signal with g-value of 2.00320 and linewidth of about 0.1 mT. Using EPR spectrum simulation, the similarity between the mechanically induced signal and the signal generated when the enamel is heated in air at a temperature above 600 degrees C was investigated. Results indicate that the mechanically induced signal is related to sample temperature increase during mechanical friction.