Computational tools in rehabilitation of erectile dysfunction

Superficial tunica albuginea rupture as initial starting point of Peyronie's disease: a topic for interdisciplinary consideration

Peyronie's disease is a connective tissue disorder in the soft tissue of the penis. The underlying cause of Peyronie's disease is not well understood but is thought to be caused by trauma or injury to the penis during sexual intercourse. The purpose of the interdisciplinary cooperation between urological surgery and physics is the development of a physical simulation tool in order to give prognosis of possible tunica albuginea fibre rupture at a certain degree of deviation of the penis. For our group the first challenge was to translate the human organ of the penis into a physical model. Starting and marginal parameters had to be defined, whereby some of them had to be based on assumption, as physical data of the human living tissue have rarely been measured up to now. The algorithm and its dependencies had to be developed. This paper is a first step of a three-dimensional mathematical-physical simulation with the assumption of a 100% filled rigid penis. The calculation gives proof of the hypothesis that the fibre-load-angle of the penis is less than 12 degrees. Thus physical simulation is able to provide the surgeon with a simple instrument to calculate and forecast the risk of the individual patient.

The biomechanics of erections: two- versus one-compartment pressurized vessel modeling of the penis

Previous biomechanical models of the penis simulated penile erections utilizing 2D geometry, simplified 3D geometry or made inaccurate assumptions altogether. These models designed the shaft of the penis as a one-compartment pressurized vessel fixed at one end when in reality it is a two-compartment pressurized vessel in which the compartments diverge as they enter the body and are fixed at two separate anatomic sites. This study utilizes the more anatomically correct two-compartment penile model to investigate erectile function. Simplified 2D and 3D models of the erect penis were developed using the finite element method with varying anatomical considerations for analyzing structural stresses, axial buckling, and lateral deformation. This study then validated the results by building and testing corresponding physical models. Finally, a more complex and anatomically accurate model of the penis was designed and analyzed. When subject to a lateral force of 0.5 N, the peak equivalent von Mises (EVM) stress in the two-compartment model increased by about 31.62%, while in the one-compartment model, the peak EVM stress increased by as high as 70.11%. The peak EVM stress was 149 kPa in the more complex and anatomically accurate penile model. When the perforated septum was removed, the peak EVM stress increased to 455 kPa. This study verified that there is significant difference between modeling the penis as a two- versus a one-compartment pressurized vessel. When subjected to external forces, a significant advantage was exhibited by two corporal based cavernosal bodies separated by a perforated septum as opposed to one corporal body. This is due to better structural integrity of the tunica albuginea when subjected to external forces.

Biomechanics of male erectile function

Two major branches of engineering mechanics are fluid mechanics and structural mechanics, with many practical problems involving the effect of the first on the second. An example is the design of an aircraft's wings to bend within reasonable limits without breaking under the action of lift forces exerted by the air flowing over them; another is the maintenance of the structural integrity of a dam designed to hold back a water reservoir which would exert very large forces on it. Similarly, fluid and structural mechanics are involved in the engineering analysis of erectile function: it is the hydraulic action of increased blood flow into the corpora cavernosa that creates the structural rigidity necessary to prevent collapse of the penile column.

Hardness evaluation of penile prostheses

AIM

This work investigates the hardness and buckling force of penile prostheses to further understand the rigidity of penile prostheses before and after implantation.

METHODS

Evaluated herein are four prosthetic samples (three inflatable, one semi-rigid), five real prostheses (one inflatable, four semi-rigid), and one prosthesis after implantation. The hardness is measured with a Shore Durimeter by pressing the tester's indentor to the surface of the specimen. A volunteer with inflatable prosthesis implantation is evaluated with respect to penile hardness versus various numbers of pumping. The buckling force of the prosthesis is also determined by a push-pull gauge and a specially designed sampling table.

RESULTS

Results in this study demonstrate that although the inflatable prosthesis could only be pumped to a certain amount of hardness, hardness and buckling force correlate well with each other. After reaching the hardness limit, prostheses can even be pumped a further few times. However, continuous pumping only puts more tension on the prosthetic material without increasing hardness and could induce mechanical failure of the prosthesis. Results also indicate that the buckling force decreases with increasing length of the semirigid prostheses, and increases when the prosthesis has a larger diameter.

CONCLUSION

This mechanical measurement of rigidity in penile prostheses could provide more information to clinicians about the penile prosthesis before surgical implantation, and to patients about prosthesis usage after implantation.

Microarray analysis reveals novel gene expression changes associated with erectile dysfunction in diabetic rats

To investigate the full range of molecular changes associated with erectile dysfunction (ED) in Type 1 diabetes, we examined alterations in penile gene expression in streptozotocin-induced diabetic rats and littermate controls. With the use of Affymetrix GeneChip arrays and statistical filtering, 529 genes/transcripts were considered to be differentially expressed in the diabetic rat cavernosum compared with control. Gene Ontology (GO) classification indicated that there was a decrease in numerous extracellular matrix genes (e.g., collagen and elastin related) and an increase in oxidative stress-associated genes in the diabetic rat cavernosum. In addition, PubMatrix literature mining identified differentially expressed genes previously shown to mediate vascular dysfunction [e.g., ceruloplasmin (Cp), lipoprotein lipase, and Cd36] as well as genes involved in the modulation of the smooth muscle phenotype (e.g., Kruppel-like factor 5 and chemokine C-X3-C motif ligand 1). Real-time PCR was used to confirm changes in expression for 23 relevant genes. Further validation of Cp expression in the diabetic rat cavernosum demonstrated increased mRNA levels of the secreted and anchored splice variants of Cp. CP protein levels showed a 1.9-fold increase in tissues from diabetic rats versus controls. Immunohistochemistry demonstrated localization of CP protein in cavernosal sinusoids of control and diabetic animals, including endothelial and smooth muscle layers. Overall, this study broadens the scope of candidate genes and pathways that may be relevant to the pathophysiology of diabetes-induced ED as well as highlights the potential complexity of this disorder.