Developments of Dispersive Liquid-Liquid Microextraction Technique

Determination of capsaicin at trace levels in different food, biological and environmental samples by quadruple isotope dilution-gas chromatography mass spectrometry after its preconcentration

Despite the therapeutic properties of capsaicin for some diseases, it shows some side effects for human health. The goal of this study was to develop a precise and accurate analytical strategy for the trace determination of capsaicin in different food, biological and environmental samples including pepper, saliva and wastewater by gas chromatography-mass spectrometry (GC-MS) after spraying-based fine droplet formation-liquid phase microextraction (SFDF-LPME) and quadruple isotope dilution (ID4) method. Acetic anhydride was used as derivatizing agent, and the extraction method was used to enrich the analyte derivative to reach low detection limits. Under the optimum conditions, limit of detection (LOD) and limit of quantitation (LOQ) were determined to be 0.33 and 1.10 µg/kg, respectively. Percent recoveries calculated for SFDF-LPME-GC-MS method ranged between 84.1 and 131.7 %. After the application of ID4-SFDF-LPME-GC-MS method, percent recoveries were obtained in the range of 94.9 and 104.0 % (%RSD ≤ 2.8) for the selected samples. It is obvious that the isotope dilution-based method provided high accurate and precise results due to the elimination of errors during the derivatization, extraction and measurement steps.

Vortex-assisted dispersive liquid-liquid microextraction-gas chromatography (VADLLME-GC) determination of residual ketamine, nimetazepam, and xylazine from drug-spiked beverages appearing in liquid, droplet, and dry forms

Presently, investigations of drug-facilitated crimes (DFCs) rely on the detection of substances extracted from biological samples following intake by the victim. However, such detection requires rapid sampling and analysis prior to metabolism and elimination of the drugs from the body. In cases of suspected DFCs, drug-spiked beverage samples, whether in liquid, droplet, or even dried form, can be tested for the presence of spike drugs and used as evidence for the occurrence of DFCs. This study aimed to quantitatively determine three sedative-hypnotics (ketamine, nimetazepam, and xylazine) from drug-spiked beverages using a vortex-assisted dispersive liquid-liquid microextraction-gas chromatography (VADLLME-GC) approach. In this study, a GC method was first developed and validated, followed by the optimization of the VADLLME protocol, which was then applied to quantify the target substances in simulated forensic case scenarios. The developed GC method was selective, sensitive (limit of detection: 0.08 μg/ml [ketamine]; 0.16 μg/ml [nimetazepam]; 0.08 μg/ml [xylazine]), linear (R²  > 0.99), precise (%RSD <7.2%), and accurate (% recovery: 92.8%-103.5%). Higher recoveries were achieved for the three drugs from beverage samples in liquid form (51%-97%) as compared to droplet (48%-96%) and dried (44%-93%) residues. The recovery was not hindered by very low volumes of spiked beverage and dried residues. In conclusion, the developed VADLLME-GC method successfully recovered ketamine, nimetazepam, and xylazine from spiked beverages that are likely to be encountered during forensic investigation of DFCs.

Dispersive liquid-liquid microextraction method combined with sugaring-out homogeneous liquid-liquid extraction for the determination of some pesticides in molasses samples

In this study, a sensitive analytical method was developed to determine some pesticides (cyprodinil, trifloxystrobin, prometryn, propachlor, fenitrothion, chlorpyrifos, profenofos, and phosalone) in molasses samples. Pesticides were extracted from samples by dispersive liquid-liquid microextraction method combined with sugaring-out homogeneous liquid-liquid extraction and determined by gas chromatography-mass spectrometry analysis. In this method, pesticides in molasses samples were first extracted using a water-miscible solvent (acetonitrile) in the sugaring-out homogeneous liquid-liquid extraction stage. The sugar in the ratio of 84-88% naturally contained in the molasses sample enabled phase separation in the acetonitrile-water homogeneous mixture. Then acetonitrile phase containing pesticides was used as dispersing solvent in the second step of the process. Under the specified optimum conditions, the limit of detection was calculated between 0.8-6.1 ng/g and the limit of quantification was in the range of 2.5-20 ng/g. The relative standard deviation values of molasses samples containing 150 ng/g of each analyte were found to be lower than 4.9% intra-day and 5.6% for inter-day. This validated method has been successfully applied to different types of molasses.

Graphene Assisted in the Analysis of Coumarins in Angelicae Pubescentis Radix by Dispersive Liquid-Liquid Microextraction Combined with 1H-qNMR

The content of active components in traditional Chinese medicine is relatively small, and it is difficult to detect some trace components with modern analytical instruments, so good pretreatment and extraction are very important in the experiment. Graphene was introduced by a dispersive liquid–liquid microextraction method based on solidification of floating organic drop (DLLME-SFO) with graphene/1-dodecyl alcohol used as the extractant, and this method, combined with quantitative proton nuclear magnetic resonance spectroscopy (¹H-qNMR), was used to simultaneously qualitative and quantitative osthole, columbianadin and isoimperatorin in Angelicae Pubescentis Radix. In this experiment, a magnetic stirrer was used for extraction, all NMR spectra were recorded on a Bruker Advance III 600 MHz spectrometer with dimethyl sulfoxide-d₆ (DMSO-d₆) as deuterated solvent and pyrazine as the internal standard. The influencing factors and NMR parameters in the extraction process were investigated and optimized. In addition, the methodology of the established method was also examined. The quantitative signals of osthole, columbianadin and isoimperatorin were at a chemical shift of δ6.25–δ6.26 ppm, δ6.83–δ6.85 ppm, and δ6.31–δ6.32 ppm. The linear ranges of osthole, columbianadin and isoimperatorin were all 0.0455–2.2727 mg/mL, and R² were 0.9994, 0.9994 and 0.9995, respectively. The limits of detection of osthole, columbianadin and isoimperatorin were 0.0660, 0.0720, 0.0620 mg, and the limits of quantification of osthole, columbianadin and isoimperatorin were 0.2201, 0.2401, 0.2066 mg/mL. The solution had good stability and repeatability within 24 h. The recoveries of osthole, columbianadin and isoimperatorin were 102.26%, 99.89%, 103.28%, respectively. The established method is simple and easy to operate, which greatly reduces the cumbersome pretreatment of samples and has high extraction efficiency.

Pretreatment and determination methods for benzimidazoles: An update since 2005

Benzimidazoles, commonly used as pesticides and veterinary drugs, have posed a threat to human health and the environment due to unreasonable use and lack of valid regulation. Therefore, an up-to-date and comprehensive summary of the pretreatment and analytical approaches in different substrates is urgently needed. The present review consequently updates and covers various newly developed pretreatment methods (e.g., cationic micellar precipitation, magnetic-solid phase extraction, hollow fiber liquid phase microextraction, disperse liquid-liquid microextraction-solidified floating organic drop, stir cake sorptive extraction, solid phase microextraction method, QuEChERS, and molecular imprinted polymer-based methods) since 2005. The review also elaborates and discusses different determination methods (e.g., newly developed HPLC and related methods, improved spectrofluorimetry methods, capillary electrophoresis, and the electrochemical sensor). Furthermore, some critical points and prospects are highlighted, to describe the trends in this area.

A miniaturized spray-assisted fine-droplet-formation-based liquid-phase microextraction method for the simultaneous determination of fenpiclonil, nitrofen and fenoxaprop-ethyl as pesticides in soil samples

RATIONALE

Pesticides are a group of micropollutants that persist for a long time in the environment and pose threats to life. Much effort has been devoted to developing pre-concentration methods capable of producing samples suitable for the detection of pesticides. However, better methods are still required to detect these compounds when they are present in trace concentrations in soils.

METHOD

Spray-assisted fine-droplet-formation-based liquid-phase microextraction was used to prepare soil samples containing three different pesticides, fenpiclonil, nitrofen and fenoxaprop-ethyl, for subsequent analysis by gas chromatography/mass spectrometry (GC/MS). A spraying apparatus was used for the dispersion of the extraction solvent into the sample/standard solution to improve the extraction efficiency. Optimization studies were performed to lower the detection limits of these analytes and the results obtained by the application of the newly developed system were compared with those obtained using the conventional GC/MS method.

RESULTS

A calibration curve over the range 5.0-100 μg L^-1 was obtained under the optimal conditions. The limits of detection and quantification were 1.56-1.80 μg L^-1 and 5.21-5.98 μg L^-1 , respectively. The enhancements in detection ability over the conventional method for the three tested pesticides were 188.01, 176.96 and 517.14 for fenpiclonil, nitrofen and fenoxaprop-ethyl, respectively Recovery studies performed in soil samples were satisfactory reflecting accurate applicability of the developed method.

CONCLUSIONS

The developed microextraction method is a time-saving and simple version of the traditional dispersive liquid-liquid microextraction method that also reduces the use of dispersive solvents.

A novel and rapid extraction protocol for sensitive and accurate determination of prochloraz in orange juice samples: Vortex-assisted spraying-based fine droplet formation liquid-phase microextraction before gas chromatography-mass spectrometry

A novel, ecofriendly, and easy extraction and preconcentration method named as vortex-assisted spraying-based fine droplet formation liquid-phase microextraction was proposed for the determination of prochloraz at trace levels in orange juice samples by gas chromatography-mass spectrometry (GC-MS). In this novel system, extraction solvent is dispersed by the help of spraying apparatus instead of dispersive solvent. Various parameters of the method were carefully optimized to increase signal-to-noise ratio of the analyte. Under the optimum chromatographic and extraction conditions, limit of detection and limit of quantification were calculated as 3.2 and 10.8 μg/kg, respectively. Moreover, enhancement in quantification power for the GC-MS system was determined as 372 folds based on LOQ comparison. Relative recovery results for orange juice samples were found to be between 95.0-107.7% by utilizing matrix matching calibration. Furthermore, the developed method may be used to efficiently and simply extract other organic compounds for their determinations in several matrices.

Analytical Scheme for Simultaneous Determination of Phthalates and Bisphenol A in Honey Samples Based on Dispersive Liquid-Liquid Microextraction Followed by GC-IT/MS. Effect of the Thermal Stress on PAE/BP-A Levels

In this paper, an analytical protocol was developed for the simultaneous determination of phthalates (di-methyl phthalate DMP, di-ethyl phthalate DEP, di-isobutyl phthalate DiBP, di-n-butyl phthalate DBP, bis-(2-ethylhexyl) phthalate DEHP, di-n-octyl phthalate DNOP) and bisphenol A (BPA). The extraction technique used was the ultrasound vortex assisted dispersive liquid–liquid microextraction (UVA-DLLME). The method involves analyte extraction using 75 µL of benzene and subsequent analysis by gas chromatography combined with ion trap mass spectrometry (GC-IT/MS). The method is sensitive, reliable, and reproducible with a limit of detection (LOD) below 13 ng g⁻¹ and limit of quantification (LOQ) below 22 ng g⁻¹ and the intra- and inter-day errors below 7.2 and 9.3, respectively. The method developed and validated was applied to six honey samples (i.e., four single-use commercial ones and two home-made ones. Some phthalates were found in the samples at concentrations below the specific migration limits (SMLs). Furthermore, the commercial samples were subjected to two different thermal stresses (24 h and 48 h at 40 °C) for evidence of the release of plastic from the containers. An increase in the phthalate concentrations was observed, especially during the first phase of the shock, but the levels were still within the limits of the regulations.

Binary Dispersive Liquid-Liquid Microextraction Strategy for Accurate and Precise Determination of Micropollutants in Lake, Well and Wastewater Matrices

In this study, a binary mixture in dispersive liquid-liquid microextraction was used for the preconcentration and determination of selected pesticides, pharmaceutical and hormone by GC-MS. A Box-Behnken experimental design was used to optimize the amounts of binary mixture, dispersive solvent and salt. The optimum parameters obtained were dichloromethane/1,2-dichloroethane binary mixture (200 µL), ethanol (2.0 mL) and potassium nitrate (1.0 g). Analytical performance of each analyte was determined under the optimum conditions and the lowest and highest detection limits calculated were 0.43 and 5.9 ng/mL. Low relative standard deviations were obtained even in the lowest concentrations in linear calibration plots, signifying high precision for the sample preparation procedure and instrumental measurement. Accuracy of the developed method and applicability to real samples was tested on well, lake, hospital and municipal wastewater. The percent recoveries acquired at different spiked concentrations were satisfactory (89%-108%), validating the accuracy of the method for the quantification of the analytes in the selected matrices.

State-of-the-art on the technique of dispersive liquid-liquid microextraction

Dispersive liquid-liquid microextraction is a new sample pretreatment technology based on traditional liquid liquid extraction. In this paper, the application of low-toxicity extractants such as low-density extractants, auxiliary extractants, stripping agents and ionic liquids in this technology and the extraction modes such as solvent de-emulsification, suspension extractant curing, auxiliary extraction, back extraction, and ionic liquid-dispersion liquid microextraction, are summarized. In addition, the synergism of this technique with other sample preparation techniques, such as liquid-liquid extraction, solid-phase extraction, solid-phase microextraction, dispersive solid phase extraction, matrix solid-phase dispersion extraction, supercritical fluid extraction and ultrasound-assisted dispersive liquid-liquid microextraction is discussed.

Dispersive liquid-liquid microextraction for rapid and inexpensive determination of tetramethylpyrazine in vinegar

The concentration of tetramethylpyrazine (TMP) in vinegar is an active indicator of vinegar quality. Dispersive liquid-liquid microextraction (DLLME) was first applied to vinegar as a clean-up pre-treatment for the rapid (5 min) determination of TMP by high-pressure liquid chromatography with ultraviolet detection (HPLC-UV), and may serve as an alternative to solid-phase extraction (SPE) or solid-phase microextraction (SPME). High sensitivity of HPLC for TMP determination was obtained using the DLLME pretreatment, with a limit of detection (LOD) of 0.001 mg L^-1 and limit of quantification (LOQ) of 0.005 mg L^-1. The developed method exhibited excellent linearity in the concentration range of 0.050-80.000 mg L^-1, with a correlation coefficient R² > 0.999. Furthermore, the percentage recovery of TMP in vinegar using the developed method was within the range 97.97-105.24%. Therefore, DLLME coupled with HPLC-UV is a sensitive and promising method for vinegar clean-up and TMP assay.

Miniaturized sample preparation methods for saliva analysis

Saliva, as the first body fluid encountering with the exogenous materials, has good correlation with blood and plays an important role in bioanalysis. However, saliva has not been studied as much as the other biological fluids mainly due to restricted access to its large volumes. In recent years, there is a growing interest for saliva analysis owing to the emergence of miniaturized sample preparation methods. The purpose of this paper is to review all microextraction methods and their principles of operation. In the following, we examine the methods used to analyze saliva up to now and discuss the potential of the other microextraction methods for saliva analysis to encourage research groups for more focus on this important subject area.

Development of an efficient sample preparation method for the speciation of Se(iv)/Se(vi) and total inorganic selenium in blood of children with acute leukemia

In this study, a new solidified deep eutectic solvent microextraction (SDES-ME) method was applied for the speciation of Se(iv), Se(vi) and total inorganic selenium in the blood of children with leukemia from Kermanshah, Iran, prior to analysis by iridium-modified tube graphite furnace atomic absorption spectrometry (GFAAS).

Simultaneous determination of Brilliant Green and Crystal Violet dyes in fish and water samples with dispersive liquid-liquid micro-extraction using ionic liquid followed by zero crossing first derivative spectrophotometric analysis method

In this study, dispersive liquid-liquid micro-extraction using ionic liquid (IL-DLLME) combined with zero crossing first derivative spectrophotometric method was applied to quantitative determination of triphenylmethane dyes in binary mixtures. The 1-methyl-3-octylimidazolium hexafluorophosphate [OMIM][PF₆] ionic liquid was used to extract Brilliant Green (BG) and Crystal Violet(CV) dyes from aqueous solutions. The amplitude of the zero crossing first derivative spectra at 670 nm and 532 nm were selected for the determination of BG and CV, respectively. Significant factors influencing the extraction of BG and CV such as sample pH, kind of extraction solvent, amount of extractant, extraction and centrifuging times and ionic strength were investigated. Under the optimal conditions, the calibration curves for the simultaneous determination of both dyes were found to be linear in the range of 10-500 μg L^-1 with detection limits (LODs) of 2.7 μg L^-1 and 1.4 μg L^-1 for BG and CV, respectively. The relative standard deviation (RSD%) for five replicate simultaneous determinations of BG and CV were 4.7% and 1.7%, respectively. Extraction efficiencies of the BG and CV dyes in the presence of interfering ions were also investigated. Sample preparation based on the quick, easy, cheap, effective, rugged and safe (QuEChERS) extraction combined with the IL-DLLME method and zero crossing first derivative spectrophotometric detection was applied for the simultaneous analysis of BG and CV in fish and water samples with quantitative recoveries.

Analysis of Volatile Compounds by Advanced Analytical Techniques and Multivariate Chemometrics

Smelling is one of the five senses, which plays an important role in our everyday lives. Volatile compounds are, for example, characteristics of food where some of them can be perceivable by humans because of their aroma. They have a great influence on the decision making of consumers when they choose to use a product or not. In the case where a product has an offensive and strong aroma, many consumers might not appreciate it. On the contrary, soft and fresh natural aromas definitely increase the acceptance of a given product. These properties can drastically influence the economy; thus, it has been of great importance to manufacturers that the aroma of their food product is characterized by analytical means to provide a basis for further optimization processes. A lot of research has been devoted to this domain in order to link the quality of, e.g., a food to its aroma. By knowing the aromatic profile of a food, one can understand the nature of a given product leading to developing new products, which are more acceptable by consumers. There are two ways to analyze volatiles: one is to use human senses and/or sensory instruments, and the other is based on advanced analytical techniques. This work focuses on the latter. Although requirements are simple, low-cost technology is an attractive research target in this domain; most of the data are generated with very high-resolution analytical instruments. Such data gathered based on different analytical instruments normally have broad, overlapping sensitivity profiles and require substantial data analysis. In this review, we have addressed not only the question of the application of chemometrics for aroma analysis but also of the use of different analytical instruments in this field, highlighting the research needed for future focus.

Determination of Levetiracetam in Human Plasma by Dispersive Liquid-Liquid Microextraction Followed by Gas Chromatography-Mass Spectrometry

Levetiracetam (LEV) is an antiepileptic drug that is clinically effective in generalized and partial epilepsy syndromes. The use of this drug has been increasing in clinical practice and intra- or -interindividual variability has been exhibited for special population. For this reason, bioanalytical methods are required for drug monitoring in biological matrices. So this work presents a dispersive liquid-liquid microextraction method followed by gas chromatography-mass spectrometry (DLLME-GC-MS) for LEV quantification in human plasma. However, due to the matrix complexity a previous purification step is required. Unlike other pretreatment techniques presented in the literature, for the first time, a procedure employing ultrafiltration tubes Amicon® (10 kDa porous size) without organic solvent consumption was developed. GC-MS analyses were carried out using a linear temperature program, capillary fused silica column, and helium as the carrier gas. DLLME optimized parameters were type and volume of extraction and dispersing solvents, salt addition, and vortex agitation time. Under chosen parameters (extraction solvent: chloroform, 130 μL; dispersing solvent: isopropyl alcohol, 400 μL; no salt addition and no vortex agitation time), the method was completely validated and all parameters were in agreement with the literature recommendations. LEV was quantified in patient's plasma sample using less than 550 μL of organic solvent.

[Cu(phen)2](2+) acts as electrochemical indicator and anchor to immobilize probe DNA in electrochemical DNA biosensor

We demonstrate a novel protocol for sensitive in situ label-free electrochemical detection of DNA hybridization based on copper complex ([Cu(phen)2](2+), where phen = 1,10-phenanthroline) and graphene (GR) modified glassy carbon electrode. Here, [Cu(phen)2](2+) acted advantageously as both the electrochemical indicator and the anchor for probe DNA immobilization via intercalative interactions between the partial double helix structure of probe DNA and the vertical aromatic groups of phen. GR provided large density of docking site for probe DNA immobilization and increased the electrical conductivity ability of the electrode. The modification procedure was monitored by electrochemical impedance spectroscopy (EIS). Square-wave voltammetry (SWV) was used to explore the hybridization events. Under the optimal conditions, the designed electrochemical DNA biosensor could effectively distinguish different mismatch degrees of complementary DNA from one-base mismatch to noncomplementary, indicating that the biosensor had high selectivity. It also exhibited a reasonable linear relationship. The oxidation peak currents of [Cu(phen)2](2+) were linear with the logarithm of the concentrations of complementary target DNA ranging from 1 × 10(-12) to 1 × 10(-6) M with a detection limit of 1.99 × 10(-13) M (signal/noise = 3). Moreover, the stability of the electrochemical DNA biosensor was also studied.