Surface-grafted molecularly imprinted polymers for protein recognition

Template bacteria-free fabrication of surface imprinted polymer-based biosensor for E. coli detection using photolithographic mimics: Hacking bacterial adhesion

As one class of molecular imprinted polymers (MIPs), surface imprinted polymer (SIP)-based biosensors show great potential in direct whole-bacteria detection. Micro-contact imprinting, that involves stamping the template bacteria immobilized on a substrate into a pre-polymerized polymer matrix, is the most straightforward and prominent method to obtain SIP-based biosensors. However, the major drawbacks of the method arise from the requirement for fresh template bacteria and often non-reproducible bacteria distribution on the stamp substrate. Herein, we developed a positive master stamp containing photolithographic mimics of the template bacteria (E. coli) enabling reproducible fabrication of biomimetic SIP-based biosensors without the need for the "real" bacteria cells. By using atomic force and scanning electron microscopy imaging techniques, respectively, the E. coli-capturing ability of the SIP samples was tested, and compared with non-imprinted polymer (NIP)-based samples and control SIP samples, in which the cavity geometry does not match with E. coli cells. It was revealed that the presence of the biomimetic E. coli imprints with a specifically designed geometry increases the sensor E. coli-capturing ability by an "imprinting factor" of about 3. These findings show the importance of geometry-guided physical recognition in bacterial detection using SIP-based biosensors. In addition, this imprinting strategy was employed to interdigitated electrodes and QCM (quartz crystal microbalance) chips. E. coli detection performance of the sensors was demonstrated with electrochemical impedance spectroscopy (EIS) and QCM measurements with dissipation monitoring technique (QCM-D).

Molecularly imprinted polymers for sensing/depleting human serum albumin (HSA): A critical review of recent advances and current challenges

Human serum albumin (HSA) is an essential biomacromolecule in the blood circulatory system because it carries numerous molecules, including fatty acids (FAs), bilirubin, metal ions, hormones, and different pharmaceuticals, and plays a significant role in regulating blood osmotic pressure. Fluctuations in HSA levels in human biofluids, particularly urine and serum, are associated with several disorders, such as elevated blood pressure, diabetes mellitus (DM), liver dysfunction, and a wide range of renal diseases. Thus, the ability to quickly and accurately measure HSA levels is important for the rapid identification of these disorders in human populations. Molecularly imprinted polymers (MIPs), well known as artificial antibodies (Abs), have been extensively used for the quantitative detection of small molecules and macromolecules, especially HSA, in recent decades. This review highlights major challenges and recent developments in the application of MIPs to detect HSA in artificial and real samples. The fabrication and application of various MIPs for the depletion of HSA are also discussed, as well as different MIP preparation approaches and strategies for overcoming obstacles that hinder the development of MIPs with high efficiency and recognition capability for HSA determination/depletion.

Molecular imprinting technology for biomedical applications

Molecularly imprinted polymers (MIPs), a type of biomimetic material, have attracted considerable interest owing to their cost-effectiveness, good physiochemical stability, favourable specificity and selectivity for target analytes, and widely used for various biological applications. It was demonstrated that MIPs with significant selectivity towards protein-based targets could be applied in medicine, diagnostics, proteomics, environmental analysis, sensors, various in vivo and/or in vitro applications, drug delivery systems, etc. This review provides an overview of MIPs dedicated to biomedical applications and insights into perspectives on the application of MIPs in newly emerging areas of biotechnology. Many different protocols applied for the synthesis of MIPs are overviewed in this review. The templates used for molecular imprinting vary from the minor glycosylated glycan-based structures, amino acids, and proteins to whole bacteria, which are also overviewed in this review. Economic, environmental, rapid preparation, stability, and reproducibility have been highlighted as significant advantages of MIPs. Particularly, some specialized MIPs, in addition to molecular recognition properties, can have high catalytic activity, which in some cases could be compared with other bio-catalytic systems. Therefore, such MIPs belong to the class of so-called 'artificial enzymes'. The discussion provided in this manuscript furnishes a comparative analysis of different approaches developed, underlining their relative advantages and disadvantages highlighting trends and possible future directions of MIP technology.

Microcontact-Imprinted Optical Sensors for Virulence Factors of Periodontal Disease

Periodontitis (gum disease) is a common biofilm-mediated oral condition, with around 7% of the adult population suffering from severe disease with risk for tooth loss. Moreover, periodontitis virulence markers have been found in atherosclerotic plaque and brain tissue, suggesting a link to cardiovascular and Alzheimer's diseases. The lack of accurate, fast, and sensitive clinical methods to identify patients at risk leads, on the one hand, to patients being undiagnosed until the onset of severe disease and, on the other hand, to overtreatment of individuals with mild disease, diverting resources from those patients most in need. The periodontitis-associated bacterium, Porphyromonas gingivalis, secrete gingipains which are highly active proteases recognized as key virulence factors during disease progression. This makes them interesting candidates as predictive biomarkers, but currently, there are no methods in clinical use for monitoring them. Quantifying the levels or proteolytic activity of gingipains in the periodontal pocket surrounding the teeth could enable early-stage disease diagnosis. Here, we report on a monitoring approach based on high-affinity microcontact imprinted polymer-based receptors for the Arg and Lys specific gingipains Rgp and Kgp and their combination with surface plasmon resonance (SPR)-based biosensor technology for quantifying gingipain levels in biofluids and patient samples. Therefore, Rgp and Kgp were immobilized on glass coverslips followed by microcontact imprinting of poly-acrylamide based films anchored to gold sensor chips. The monomers selected were N-isopropyl acrylamide (NIPAM), N-hydroxyethyl acrylamide (HEAA) and N-methacryloyl-4-aminobenzamidine hydrochloride (BAM), with N,N'-methylene bis(acrylamide) (BIS) as the crosslinker. This resulted in imprinted surfaces exhibiting selectivity towards their templates high affinity and selectivity for the templated proteins with dissociation constants (K _d) of 159 and 299 nM for the Rgp- and Kgp-imprinted, surfaces respectively. The former surface displayed even higher affinity (K _d = 71 nM) when tested in dilute cell culture supernatants. Calculated limits of detection for the sensors were 110 and 90 nM corresponding to levels below clinically relevant concentrations.

The utility of molecularly imprinted polymers for mass spectrometric protein and proteomics analysis

Selective and efficient sample clean-up is important in mass spectrometric protein- and proteomics analyses from biological matrices. Molecularly imprinted polymers (MIPs), polymers prepared to have tailor-made cavities for capture of target analytes may by such represent an interesting alternative for selective clean-up. The present review aims to give an overview of the utility of MIPs for protein capture from biological matrices prior to mass spectrometry (MS) analysis. The application of MIPs in depletion of abundant proteins, in protein and proteotypic peptide capture as well as in capture of post-translational modifications (PTMs) is described and discussed. In addition, an overview of available MIP formats and their advantages and challenges is given, together with an overview of the mass spectrometric techniques used in protein analysis after MIP capture. Overall, the present literature demonstrates that for many applications MIPs for sample clean-up in mass spectrometric protein and proteomics analysis from biological matrices is still not fully matured. MIPs for proteotypic peptide capture is the most mature approach and a method for routine use may be available within the next few years.

Development of molecularly imprinted polymer based phase boundaries for sensors design (review)

Achievements in polymer chemistry enables to design artificial phase boundaries modified by imprints of selected molecules and some larger structures. These structures seem very useful for the design of new materials suitable for affinity chromatography and sensors. In this review, we are overviewing the synthesis of molecularly imprinted polymers (MIPs) and the applicability of these MIPs in the design of affinity sensors. Such MIP-based layers or particles can be used as analyte-recognizing parts for sensors and in some cases they can replace very expensive compounds (e.g.: antibodies, receptors etc.), which are recognizing analyte. Many different polymers can be used for the formation of MIPs, but conducing polymers shows the most attractive capabilities for molecular-imprinting by various chemical compounds. Therefore, the application of conducting polymers (e.g.: polypyrrole, polyaniline, polythiophene, poly(3,4-ethylenedioxythiophene), and ortho-phenylenediamine) seems very promising. Polypyrrole is one of the most suitable for the development of MIP-based structures with molecular imprints by analytes of various molecular weights. Overoxiation of polypyrrole enables to increase the selectivity of polypyrrole-based MIPs. Methods used for the synthesis of conducting polymer based MIPs are overviewed. Some methods, which are applied for the transduction of analytical signal, are discussed, and challenges and new trends in MIP-technology are foreseen.

Electrochemically Deposited Molecularly Imprinted Polymer-Based Sensors

This review is dedicated to the development of molecularly imprinted polymers (MIPs) and the application of MIPs in sensor design. MIP-based biological recognition parts can replace receptors or antibodies, which are rather expensive. Conducting polymers show unique properties that are applicable in sensor design. Therefore, MIP-based conducting polymers, including polypyrrole, polythiophene, poly(3,4-ethylenedioxythiophene), polyaniline and ortho-phenylenediamine are frequently applied in sensor design. Some other materials that can be molecularly imprinted are also overviewed in this review. Among many imprintable materials conducting polymer, polypyrrole is one of the most suitable for molecular imprinting of various targets ranging from small organics up to rather large proteins. Some attention in this review is dedicated to overview methods applied to design MIP-based sensing structures. Some attention is dedicated to the physicochemical methods applied for the transduction of analytical signals. Expected new trends and horizons in the application of MIP-based structures are also discussed.

Peptide epitope-imprinted polymer microarrays for selective protein recognition. Application for SARS-CoV-2 RBD protein

We introduce a practically generic approach for the generation of epitope-imprinted polymer-based microarrays for protein recognition on surface plasmon resonance imaging (SPRi) chips. The SPRi platform allows the subsequent rapid screening of target binding kinetics in a multiplexed and label-free manner. The versatility of such microarrays, both as synthetic and screening platform, is demonstrated through developing highly affine molecularly imprinted polymers (MIPs) for the recognition of the receptor binding domain (RBD) of SARS-CoV-2 spike protein. A characteristic nonapeptide GFNCYFPLQ from the RBD and other control peptides were microspotted onto gold SPRi chips followed by the electrosynthesis of a polyscopoletin nanofilm to generate in one step MIP arrays. A single chip screening of essential synthesis parameters, including the surface density of the template peptide and its sequence led to MIPs with dissociation constants (K D) in the lower nanomolar range for RBD, which exceeds the affinity of RBD for its natural target, angiotensin-convertase 2 enzyme. Remarkably, the same MIPs bound SARS-CoV-2 virus like particles with even higher affinity along with excellent discrimination of influenza A (H3N2) virus. While MIPs prepared with a truncated heptapeptide template GFNCYFP showed only a slightly decreased affinity for RBD, a single mismatch in the amino acid sequence of the template, i.e. the substitution of the central cysteine with a serine, fully suppressed the RBD binding.

Hybrid Molecularly Imprinted Polymers: The Future of Nanomedicine?

Molecularly imprinted polymers (MIPs) have been widely used in nanomedicine in the last few years. However, their potential is limited by their intrinsic properties resulting, for instance, in lack of control in drug release processes or complex detection for in vivo imaging. Recent attempts in creating hybrid nanomaterials combining MIPs with inorganic nanomaterials succeeded in providing a wide range of new interesting properties suitable for nanomedicine. Through this review, we aim to illustrate how hybrid molecularly imprinted polymers may improve patient care with enhanced imaging, treatments, and a combination of both.

Epitope-imprinted polymers: Design principles of synthetic binding partners for natural biomacromolecules

Molecular imprinting (MI) has been explored as an increasingly viable tool for molecular recognition in various fields. However, imprinting of biologically relevant molecules like proteins is severely hampered by several problems. Inspired by natural antibodies, the use of epitopes as imprinting templates has been explored to circumvent those limitations, offering lower costs and greater versatility. Here, we review the latest innovations in this technology, as well as different applications where MI polymers (MIPs) have been used to target biomolecules of interest. We discuss the several steps in MI, from the choice of epitope and functional monomers to the different production methods and possible applications. We also critically explore how MIP performance can be assessed by various parameters. Last, we present perspectives on future breakthroughs and advances, offering insights into how MI techniques can be expanded to new fields such as tissue engineering.

SDF-1 Molecularly Imprinted Biomimetic Scaffold as a Potential Strategy to Repair the Infarcted Myocardium

Background:

In situ cardiac tissue engineering aims to heal the infarcted myocardium by guiding tissue regeneration within the patient body. A key step in this approach is the design of a bioactive scaffold, able to stimulate tissue repair at the site of damage.

In the development of bioactive scaffolds, molecular imprinting nanotechnology has been recently proposed as a new functionalization strategy.

Objectives:

In this work, Molecularly Imprinted Particles (MIP) with recognition properties towards the stromal-derived factor-1 (SDF-1) were synthesized, characterized and used for the functionalization of a biomimetic scaffold. MIP are expected to favor the enrichment of the SDF-1 bioactive molecule within the scaffold, thereby promoting myocardial regeneration.

Methods:

MIP were obtained by precipitation polymerization, using the SDF-1 molecule as a template. Alginate/gelatin/elastin sponges were fabricated by freeze-drying and functionalized by MIP deposition. Morphological, physicochemical and functional analyses were performed both on MIP and on MIP-modified scaffolds. A preliminary biological in vitro investigation was also carried out using rat cardiac progenitor cells (rCPCs).

Results:

Imprinted nanoparticles with an average diameter between 0.6 and 0.9 µm were obtained. Infrared analysis of MIP confirmed the expected chemical structure. Recognition and selectivity tests showed that MIP were able to selectively recognize and rebind the template, even after their deposition on the scaffold. In vitro biological tests showed that cell adhesion to the scaffold was promoted by MIP functionalization.

Conclusion:

Results obtained in the present study suggest that biomimetic alginate/gelatin/elastin sponges, functionalized by MIP with recognition properties towards SDF-1, could be successfully used for tissue engineering approaches to repair the infarcted heart.

“Out of Pocket” Protein Binding—A Dilemma of Epitope Imprinted Polymers Revealed for Human Hemoglobin

The epitope imprinting approach applies exposed peptides as templates to synthesize Molecularly Imprinted Polymers (MIPs) for the recognition of the parent protein. While generally the template protein binding to such MIPs is considered to occur via the epitope-shaped cavities, unspecific interactions of the analyte with non-imprinted polymer as well as the detection method used may add to the complexity and interpretation of the target rebinding. To get new insights on the effects governing the rebinding of analytes, we electrosynthesized two epitope-imprinted polymers using the N-terminal pentapeptide VHLTP-amide of human hemoglobin (HbA) as the template. MIPs were prepared either by single-step electrosynthesis of scopoletin/pentapeptide mixtures or electropolymerization was performed after chemisorption of the cysteine extended VHLTP peptide. Rebinding of the target peptide and the parent HbA protein to the MIP nanofilms was quantified by square wave voltammetry using a redox probe gating, surface enhanced infrared absorption spectroscopy, and atomic force microscopy. While binding of the pentapeptide shows large influence of the amino acid sequence, all three methods revealed strong non-specific binding of HbA to both polyscopoletin-based MIPs with even higher affinities than the target peptides.

Advances in Molecularly Imprinted Polymers Based Affinity Sensors (Review)

Recent challenges in biomedical diagnostics show that the development of rapid affinity sensors is very important issue. Therefore, in this review we are aiming to outline the most important directions of affinity sensors where polymer-based semiconducting materials are applied. Progress in formation and development of such materials is overviewed and discussed. Some applicability aspects of conducting polymers in the design of affinity sensors are presented. The main attention is focused on bioanalytical application of conducting polymers such as polypyrrole, polyaniline, polythiophene and poly(3,4-ethylenedioxythiophene) ortho-phenylenediamine. In addition, some other polymers and inorganic materials that are suitable for molecular imprinting technology are also overviewed. Polymerization techniques, which are the most suitable for the development of composite structures suitable for affinity sensors are presented. Analytical signal transduction methods applied in affinity sensors based on polymer-based semiconducting materials are discussed. In this review the most attention is focused on the development and application of molecularly imprinted polymer-based structures, which can replace antibodies, receptors, and many others expensive affinity reagents. The applicability of electrochromic polymers in affinity sensor design is envisaged. Sufficient biocompatibility of some conducting polymers enables to apply them as "stealth coatings" in the future implantable affinity-sensors. Some new perspectives and trends in analytical application of polymer-based semiconducting materials are highlighted.

Molecular Imprinted Polymers Coupled to Photonic Structures in Biosensors: The State of Art

Optical sensing, taking advantage of the variety of available optical structures, is a rapidly expanding area. Over recent years, whispering gallery mode resonators, photonic crystals, optical waveguides, optical fibers and surface plasmon resonance have been exploited to devise different optical sensing configurations. In the present review, we report on the state of the art of optical sensing devices based on the aforementioned optical structures and on synthetic receptors prepared by means of the molecular imprinting technology. Molecularly imprinted polymers (MIPs) are polymeric receptors, cheap and robust, with high affinity and selectivity, prepared by a template assisted synthesis. The state of the art of the MIP functionalized optical structures is critically discussed, highlighting the key progresses that enabled the achievement of improved sensing performances, the merits and the limits both in MIP synthetic strategies and in MIP coupling.

How Reliable Is the Electrochemical Readout of MIP Sensors?

Electrochemical methods offer the simple characterization of the synthesis of molecularly imprinted polymers (MIPs) and the readouts of target binding. The binding of electroinactive analytes can be detected indirectly by their modulating effect on the diffusional permeability of a redox marker through thin MIP films. However, this process generates an overall signal, which may include nonspecific interactions with the nonimprinted surface and adsorption at the electrode surface in addition to (specific) binding to the cavities. Redox-active low-molecular-weight targets and metalloproteins enable a more specific direct quantification of their binding to MIPs by measuring the faradaic current. The in situ characterization of enzymes, MIP-based mimics of redox enzymes or enzyme-labeled targets, is based on the indication of an electroactive product. This approach allows the determination of both the activity of the bio(mimetic) catalyst and of the substrate concentration.

Electrochemical MIP Sensor for Butyrylcholinesterase

Molecularly imprinted polymers (MIPs) mimic the binding sites of antibodies by substituting the amino acid-scaffold of proteins by synthetic polymers. In this work, the first MIP for the recognition of the diagnostically relevant enzyme butyrylcholinesterase (BuChE) is presented. The MIP was prepared using electropolymerization of the functional monomer o-phenylenediamine and was deposited as a thin film on a glassy carbon electrode by oxidative potentiodynamic polymerization. Rebinding and removal of the template were detected by cyclic voltammetry using ferricyanide as a redox marker. Furthermore, the enzymatic activity of BuChE rebound to the MIP was measured via the anodic oxidation of thiocholine, the reaction product of butyrylthiocholine. The response was linear between 50 pM and 2 nM concentrations of BuChE with a detection limit of 14.7 pM. In addition to the high sensitivity for BuChE, the sensor responded towards pseudo-irreversible inhibitors in the lower mM range.

Selective, sensitive, and fast determination of S-layer proteins by a molecularly imprinted photonic polymer coated film and a fiber-optic spectrometer

A newly developed molecularly imprinted photonic polymer (MIPP) film, which was prepared by colloidal crystal templating and surface molecular imprinting, was used for selective capture of S-layer protein (SLP) from a complex Lactobacillus acidophilus sample. The colloidal crystal templates were formed by a dipping process followed by chemical binding of the imprinted template SLP molecules. A sandwich structure consisting of two glass slides was formed after the SLP-silica layer had been covered with a poly(methyl methacrylate) glass slide. After polymerization of the SLP-silica layer with the preprepared polymerization solution, hydrofluoric acid and acetic phosphate buffer solutions removed the silica particles and SLP molecules, respectively. The MIPP film obtained exhibited a three-dimensional, highly ordered and interconnected macroporous structure (pore size greater than 200 nm), which is specifically accessible to SLP molecules. The adsorbed SLP molecules were simply and straightforwardly detected by a fiber-optic spectrometer. The redshift of the Bragg diffraction peak of the MIPP film was linearly related to the number of SLP molecules that had been harvested in the film. The detection limit of the SLP-MMIP-fiber-optic spectrometer method for SLP was 1 ng mL^-1. The MIPP sensor was successfully applied to detect SLP molecules in a crudely extracted Lactobacillus acidophilus sample. Our results prove the applicability of the SLP-MIPP film for fast and real-time measurement of SLP. Graphical abstract.

Molecularly Imprinted Nanoparticles Assay (MINA) in Pseudo ELISA: An Alternative to Detect and Quantify Octopamine in Water and Human Urine Samples

In 2004, octopamine was added to the list of drugs banned by the world anti-doping agency (WADA) and prohibited in any sport competition. This work aims to develop a new analytical method to detect octopamine in water and human urine samples. We proposed a pseudo-enzyme-linked immunosorbent assay (pseudo-ELISA) by replacing traditional monoclonal antibodies with molecularly imprinted polymer nanoparticles (nanoMIPs). NanoMIPs were synthesised by a solid-phase approach using a persulfate initiated polymerisation in water. Their performance was analysed in pseudo competitive ELISA based on the competition between free octopamine and octopamine-HRP conjugated. The final assay was able to detect octopamine in water within the range 1 nmol·L⁻¹–0.1 mol·L⁻¹ with a detection limit of 0.047 ± 0.00231 µg·mL⁻¹ and in human urine samples within the range 1 nmol·L⁻¹–0.0001 mol·L⁻¹ with a detection limit of 0.059 ± 0.00281 µg·mL⁻¹. In all experiments, nanoMIPs presented high affinity to the target molecules and almost no cross-reactivity with analogues of octopamine such as pseudophedrine or l-Tyrosine. Only slight interference was observed from the human urine matrix. The high affinity and specificity of nanoMIPs and no need to maintain a cold chain logistics makes the nanoMIPs a competitive alternative to antibodies. Furthermore, this work is the first attempt to use nanoMIPs in pseudo-ELISA assays to detect octopamine.

Advances in the development of molecularly imprinted polymers for the separation and analysis of proteins with liquid chromatography

This review documents recent advances in the design, synthesis, characterization, and application of molecularly imprinted polymers in the form of monoliths and particles/beads for the use in the separation and analysis of proteins with solid-phase extraction or liquid chromatography. The merits of three-dimensional molecular imprinting, whereby the molecular template is randomly embedded in the polymer, and two-dimensional imprinting, in which the template is confined to the surface, are described. Target protein binding can be achieved by either using the entire protein as a template or by using a protein substructure as template, that is, a peptide, as in the "epitope" approach. The intended approach and strategy then determine the choice of polymerization method. A synopsis has been provided on methods used for the physical, chemical, and functional characterizations and associated performance evaluations of molecularly imprinted and nonimprinted control polymers, involving a diverse range of analytical techniques commonly used for low and high molecular mass analytes. Examples of recent applications demonstrate that, due to the versatility of imprinting methods, molecularly imprinted monoliths or particles/beads can be adapted to protein extraction/depletion and separation procedures relevant to, for example, protein biomarker detection and quantification in biomedical diagnostics and targeted proteomics.

Synthesis and Applications of Molecularly Imprinted Polymers Modified TiO₂ Nanomaterials: A Review

Titanium dioxide (TiO₂) nanomaterials have caused a widespread concern in the past several decades for their bulk characteristics and potential applications in many different areas. Lately, the combination between molecularly imprinted polymers (MIPs) and TiO₂ nanomaterials have been proven to improve the relative adsorption capacity, selectivity and accelerate the rate of mass transfer of analyte which is not possible using TiO₂ alone. Considering the unique performance of the MIPs modified TiO₂ nanomaterials, this review intends to give an overview of the recent progresses in the development of MIPs modified TiO₂ nanomaterials, the potential applications of their tailor-made characteristics. The limitations and challenges in this practically promising nanomaterials have also been raised and summarized. By means of the points raised in this article, we would like to provide some assistance for further development of preparation methodologies and the expansion of some potential applications in the field of MIPs modified TiO₂ nanomaterials.

Simultaneous determination of sulfonamides and fluoroquinolones from environmental water based on magnetic double-template molecularly imprinting technique

In this work, a fast and selective method based on magnetic extraction is presented for the simultaneous extraction of sulfonamides (SAs) and fluoroquinolones (FQs), followed by liquid chromatography-tandem mass spectrometry detection. In this method, magnetic surface double-template molecularly imprinted polymers (MSdt-MIPs) with superparamagnetic property and high selectivity toward both SAs and FQs were synthesized and directly applied to the simultaneous extraction of SAs and FQs from environmental water as magnetic adsorbents. The extraction and enrichment procedures could be accomplished in one single step by stirring the mixture of MSdt-MIPs and water sample, and the MSdt-MIPs with adsorbed analytes were easily separated from the water sample by a magnet afterwards. The adsorption mechanism of MSdt-MIPs was investigated by employing the adsorption thermodynamic and kinetic studies, and the selectivity of the MSdt-MIPs toward target analytes was evaluated through the selectivity test. For validation of the proposed method, the matrix effect was evaluated and compared to that of the traditional SPE method. Excellent linearity (R > 0.9990) for both SAs and FQs were obtained in the concentration range of 20-2000 ng L^-1, and the limits of detection are in the range of 3.0-4.7 ng L^-1 for SAs while 4.1-6.1 ng L^-1 for FQs. Finally, the proposed method was successfully applied to the simultaneous determination of SAs and FQs in several environmental water samples.

Magnetic surface molecularly imprinted poly(3-aminophenylboronic acid) for selective capture and determination of diethylstilbestrol

Imprinted poly(APBA) nanoshell on Fe₃O₄@SiO₂ surface was first synthesized and used for MSPE of diethylstilbestrol followed by HPLC determination.

Efficient synthesis of riboflavin-imprinted magnetic nanoparticles by boronate affinity-based surface imprinting for the selective recognition of riboflavin

Riboflavin (vitamin B2), a cis-diol-containing compound, is an essential vitamin for maintaining human health mainly in energy metabolism and is a critical component of enzyme cofactors and flavoproteins.

Development and application of a novel fluorescent nanosensor based on FeSe quantum dots embedded silica molecularly imprinted polymer for the rapid optosensing of cyfluthrin

A novel molecularly imprinted silica layer appended to FeSe quantum dots (MIP-FeSe-QDs) was fabricated and utilized as a recognition element to develop a selective and sensitive fluorescent nanosensor for cyfluthrin (CYF) determination. The MIP-FeSe-QDs were characterized by fluorescence spectrometry, scanning electron microscopy, transmission electron microscopy, and Fourier transform infrared spectroscopy. Excellent selectivity and high sensitivity of MIP-FeSe-QDs to CYF molecules were observed based on the fluorescence quenching of FeSe-QDs. Under optimal conditions, a good linear relationship was found between fluorescence quenching effect and increased CYF concentration within 0.010-0.20mg/L, with a correlation coefficient of 0.9911. The practicality of the developed sensor method for CYF detection in fish and sediment samples was further validated. Good recoveries ranging from 88.0% to 113.9% with<6.8% relative standard deviations were obtained. The detection limits of CYF in sediment and fish samples were 1.3 and 1.0µg/kg, respectively. This study established a novel, rapid fluorescent nanosensor detection method based on MIP-QDs for successfully analyzing CYF in fish and sediment samples.

Selective determination of sulfonamides from environmental water based on magnetic surface molecularly imprinting technology

In the study, a simple and selective method based on magnetic separation technology is presented for the extraction of sulfonamides (SAs) from environmental water, followed by liquid chromatography-tandem mass spectrometry. In this method, magnetic surface molecularly imprinted polymers (Fe₃O₄@SiO₂@MIPs) with super-paramagnetic property and high selectivity toward SAs were developed as magnetic adsorbents. The Fe₃O₄@SiO₂@MIPs were then applied to the selective extraction of SAs from environmental water. The extraction and enrichment were accomplished simultaneously in a single step by simply stirring the mixture of adsorbents and water samples. The Fe₃O₄@SiO₂@MIPs were characterized by scanning electron microscopy, Fourier-transform infrared spectrometry, and vibrating sample magnetometry. The adsorption thermodynamics and kinetics were employed to study the adsorption mechanism of the Fe₃O₄@SiO₂@MIPs. And the matrix effect of the method was evaluated. Calibration curves obtained by analyzing matrix-matched standards show excellent linear relationship (R = 0.9994-0.9999) in the concentration range of 10-1000 ng L^-1, and the limits of detection are in the range of 1.4-2.8 ng L^-1. The relative standard deviations of intra- and inter-day obtained are in the range of 2.8 to 7.8 and 3.1 to 7.9%, respectively. The proposed method was successfully applied to determine SAs in six environmental water samples, and SAs were detectable in four of them with the concentration from 10.5 to 120.2 ng L^-1.