Metal–Organic Framework MIL-101(Cr) for High-Performance Liquid Chromatographic Separation of Substituted Aromatics

Hybrid organic monolithic column containing MIL-68(Al) for the separation of small molecules by capillary HPLC

A hybrid organic monolithic column made of poly(lauryl methacrylate-co-1,6-hexanediol dimethacrylate) and the metal-organic framework MIL-68(Al) was prepared for the first time. The column was used in capillary liquid chromatography, both in isocratic and gradient elution modes. Separation performance towards small molecules of different chemical nature (polycyclic aromatic hydrocarbons, alkylbenzenes, phenols, etc.) was studied. Monte Carlo simulations were made to both select the proper precursors to obtain empty metal-organic framework micropores in the monolithic polymer and also, to analyze the potential free access of the studied analytes into the micropores (necessary to improve mass transfer and column efficiency). The hereby synthesized metal-organic framework microcrystals allowed obtaining homogeneous hybrid monolithic columns. Adding of MIL-68(Al) (1030 m2 g-1 BET specific surface area) increased the surface area from 3.9 m2 g-1 for the parent monolith to 18.2 m2 g-1 for the hybrid column containing 8 mg mL-1 of the microcrystals. Chromatographic performance of this new column was evaluated by studying retention factors, resolution, and plate counts at room temperature. Different compounds, not completely resolved in the parent monolith, were partially or completely separated after metal-organic framework addition. Using the monolithic column with only 2 mg mL-1 of MIL-68(Al), five alkylbenzenes were completely separated with very symmetrical peak shapes, resolution factors up to 3.60 and plate counts of 4300 plates m-1 for n-hexylbenzene. This value is higher than those obtained by other authors who used organic monolithic columns with embedded metal-organic frameworks to perform separations at room temperature. Additionally, nine polycyclic aromatic hydrocarbons were partially or completely resolved in gradient elution mode. The hybrid monolithic columns exhibited very good intra-day (%RSD=1.9), inter-day (%RSD=2.6), and column-to-column (%RSD=4.3) reproducibility values. Easy and fast column preparation, and versatility to efficiently separate several compounds of different chemical nature in isocratic and gradient mode, makes this new hybrid column a very good option for the analysis of small molecules in capillary (or nano) HPLC.

Construction of Indium(III)-Organic Framework Based on a Flexible Cyclotriphosphazene-Derived Hexacarboxylate as a Reusable Green Catalyst for the Synthesis of Bioactive Aza-Heterocycles

The constant demand for eco-friendly methods of synthesizing complex organic compounds inspired researchers to design and develop modern, highly efficient heterogeneous catalytic systems. Herein, In-HCPCP metal-organic framework (SRMIST-1), a heterogeneous Lewis acid catalyst containing less toxic indium and eco-friendly robust cyclotriphosphazene and exhibiting notable chemical and thermal stability, durable catalytic activity, and exceptional reusability was produced through the reaction between indium(III) nitrate hydrate and hexakis(4-carboxylatophenoxy)-cyclotriphosphazene. In the SRMIST-1 structure, secondary building units {InO7} are assembled by a connection of η2- and η1-carboxylic oxo atoms from different HCPCP ligands, forming a three-dimensional network. The occurrence of regularly distributed In(III) sites in SRMIST-1 confers superior reactivity on the catalyst toward the synthesis of 2,3-dihydroquinazolin-4(1H)-ones and 3,4-dihydro-2H-1,2,4-benzothiadiazine-1,1-dioxides by the cyclization reaction of 2-aminobenzamides and 2-aminobenzenesulphonamides with aldehydes under optimized reaction conditions, respectively. The notable features of this method include broad functional group compatibility, low catalyst loading (1-5 mol %), mild reaction conditions, easy workup procedures, good to excellent reaction yields, ethanol as a green solvent, reusability of the catalyst (five cycles), and economic attractiveness, which is mainly due to sustainability of SRMIST-1 as a reusable green catalyst. Our findings demonstrate that the highly reactive and reusable green catalyst finds widespread applications in medicinal chemistry.

Synthesis of hierarchically porous zirconium-based metal-organic framework@silica core-shell stationary phase through etching strategy for liquid chromatography

Metal organic frameworks (MOFs) show promise to be employed as stationary phase for high performance liquid chromatography (HPLC), however, the microporous structures of MOFs seriously restrict the diffusion and mass transfer of solute molecules, leading to a low column efficiency. In this paper, the fabrication of hierarchically porous UiO-66@SiO2 (HP- UiO-66@SiO2) core-shell microspheres via H2O2 etching has been proposed as a viable approach to enhance the separation performance of MOFs-based columns for HPLC. Through the direct treatment of the preliminary prepared UiO-66@SiO2 microspheres with H2O2 etching, HP-UiO-66@SiO2 core-shell microspheres were successfully synthesized with an enlarged pore size of up to 9 nm, facilitating efficient mass transfer in chromatographic separation. The prepared HP-UiO-66@SiO2 core-shell microspheres were then explored as stationary phase in HPLC to separate the nonpolar alkyl benzene homologues, the polar aromatic alcohol homologues and the xylene isomers. The results indicated that the baseline separations of these solutes were achieved successfully with narrow peak width and higher resolution than the UiO-66@SiO2 column. The HP-UiO-66@SiO2 column exhibited superior separation performance, reaching a maximum plate number of 134,459/m for fluorene, and showing good reproducibility. As a result, this template-free approach suggests that the fabrication of hierarchically porous MOFs@silica core-shell microspheres is a successful approach to enhance the column efficiency of MOFs-based columns in HPLC.

The development of chiral metal-organic frameworks for enantioseparation of racemates

MIL-101(Cr), an achiral metal-organic framework, made up of a terephthalic acid ligand and a metal chromium ion was selected as a template. Its structural features are unsaturated Lewis acid sites that can be easily activated and it has an extremely high specific surface area, big pore size, and good thermal/chemical/water stability. This achiral framework was modified to introduce chirality within the structure to develop chiral metal-organic frameworks (CMOFs). Here, natural chiral ligands, amino acids (l-proline, l-thioproline and l-tyrosine), were selected for post synthetic modification (PSM) of MIL-101(Cr). This is a very simple, clean and facile methodology with respect to the reactants and reaction conditions. CMOFs 1-3 abbreviated as MIL-101-l-proline (CMOF-1), MIL-101-l-thioproline (CMOF-2) and MIL-101-l-tyrosine (CMOF-3) were prepared by introducing l-proline, l-thioproline and l-tyrosine as chiral moieties within the framework of (Cr). These CMOFs were characterized by FTIR, PXRD, SEM, and thermo gravimetric analysis. Chirality within these CMOFs 1-3 was established by circular dichroism (CD) and polarimetric methods. These three CMOFs 1-3 showed enantioselectivity towards RS-ibuprofen, RS-mandelic acid and RS-1-phenylethanol to varying extents. Their enantioselectivity towards racemates was studied by chiral HPLC and polarimetry.

Preparation of Chiral Porous Organic Cage Clicked Chiral Stationary Phase for HPLC Enantioseparation

Porous organic cages (POCs) are a new subclass of porous materials, which are constructed from discrete cage molecules with permanent cavities via weak intermolecular forces. In this study, a novel chiral stationary phase (CSP) has been prepared by chemically binding a [4 + 6]-type chiral POC (C120H96N12O4) with thiol-functionalized silica gel using a thiol-ene click reaction and applied to HPLC separations. The column packed with this CSP presented good separation capability for chiral compounds and positional isomers. Thirteen racemates have been enantioseparated on this column, including alcohols, diols, ketones, amines, epoxides, and organic acids. Upon comparison with a previously reported chiral POC NC1-R-based column, commercial Chiralpak AD-H, and Chiralcel OD-H columns, this column is complementary to these three columns in terms of its enantiomeric separation; and can also separate some racemic compounds that cannot be separated by the three columns. In addition, eight positional isomers (iodoaniline, bromoaniline, chloroaniline, dibromobenzene, dichlorobenzene, toluidine, nitrobromobenzene, and nitroaniline) have also been separated. The influences of the injection weight and column temperature on separation have been explored. After the column has undergone multiple injections, the relative standard deviations (RSDs) for the retention time and selectivity were below 1.0 and 1.5%, respectively, indicating the good reproducibility and stability of the column for separation. This work demonstrates that POCs are promising materials for HPLC separation.

Trends in monoliths: Packings, stationary phases and nanoparticles

Monoliths media are gaining interest as excellent substitutes to conventional particle-packed columns. Monolithic columns show higher permeability and lower flow resistance than conventional liquid chromatography columns, providing high-throughput performance, resolution and separation in short run times. Monolithic columns with longer length, smaller inner diameter and specific selectivity to peptides or enantiomers have been played important role in hyphenated system. Monolithic stationary phases possess great efficiency, resolution, selectivity and sensitivity in the separation of complex biological samples, such as the complex mixtures of peptides for proteome analysis. The development of monolithic stationary phases has opened the new avenue in chromatographic separation science and is in turn playing much more important roles in the wide application area. Monolithic stationary phases have been widely used in fast and high efficiency one- and multi-dimensional separation systems, miniaturized devices, and hyphenated system coupled with mass spectrometers. The developing technology for preparation of monolithic stationary phases is revolutionizing the column technology for the separation of complex biological samples. These techniques using porous monoliths offer several advantages, including miniaturization and on-line coupling with analytical instruments. Additionally, monoliths are ideal support media for imprinting template-specific sites, resulting in the so-called molecularly-imprinted monoliths, with ultra-high selectivity. In this review, the origin of the concept, the differences between their characteristics and those of traditional packings, their advantages and drawbacks, theory of separations, the methods for the monoliths preparation of different forms, nanoparticle monoliths and metal-organic framework are discussed. Two application areas of monolithic metal-organic framework and nanoparticle monoliths are provided. The review article discusses the results reported in a total of 218 references. Other older references were included to illustrate the historical development of monoliths, both in preparation and types, as well as separation mechanism.

Adsorptive removal of aromatic diamines from water using metal-organic frameworks functionalized with a nitro group

Adsorptive removal of aromatic diamines such as methylenedianiline (MDA) and p-phenylenediamine (PPD) was firstly investigated with nitro-functionalized metal-organic frameworks (MOFs, MIL-101(Cr)-NO₂). The MIL-101(Cr)-NO₂ showed much better performances in the removal of MDA and PPD, in both adsorption capacity and kinetics, than any other adsorbents. For example, MIL-101(Cr)-NO₂ had a much higher maximum adsorption capacity for MDA (1111 mg·g^-1) than activated carbon (208 mg·g^-1) or a reported adsorbent (391 mg·g^-1). Based on experimental results, hydrogen bonding (especially, via the formation of a 6-membered ring (6-MR) between -NO₂ of the adsorbent and -NH₂ of the adsorbates) could be suggested as the main mechanism to interpret the noticeable adsorption of the diamines. Importantly, this is the first example to confirm that MOFs with nitro group can be a competitive adsorbent to remove organics composed of amino group, especially via making 6-MR through hydrogen bonding. Higher adsorption of MDA than that of PPD over MIL-101(Cr)-NO₂ might be explained with π-π interaction between aromatic rings (π-lean aromatics of MOF and π-rich aromatics of the adsorbates). Moreover, MIL-101(Cr)-NO₂ could be recycled after simple washing, suggesting the potential use of the MOF in adsorptive purification of contaminated water with organics with amino groups.

Metal-organic frameworks-based biosensor for microRNA detection in prostate cancer cell lines

In this research, a novel dye-labeled probe (FAM-Probe) based on a nano metal-organic framework (NMOF) functionalized with folate (NMOF-FA) was prepared and applied as a fluorescent sensing platform for the recognition of intracellular microRNA (miRNA-21) in DU145, PC3, and LNCaP cancer cells. The NMOF-FA can be easily assembled with a dye-labeled miR-21 probe (FAM-Probe21), causing an efficient fluorescence quenching of fluorescence of FAM fluorophore. The probe can be specifically catch up by cancerous cells through targeting their folate receptor by folic acid on the FAM-Probe21-NMOF-FA complex. Upon the interaction of the FAM-Probe21-NMOF-FA with complementary miRNA (miR-21), the fluorescence intensity can be recovered, providing a specific system to detect miRNAs in prostate cancer cells. We used the proposed probe for cell-specific intracellular miRNA-21 sensing, following the alteration expression level of miRNA-21 inside living cells. Thus, the FAM-Probe21-NMOF-FA complex can be used as a new miRNA sensing method in biomedicine studies.

High-field asymmetric waveform ion mobility spectrometry for xylene isomer separation assisted by helium-chemical modifiers

We propose a combined helium-chemical modifier method for a faster and more convenient separation and detection of xylene isomers. The method employs high-field asymmetric waveform ion mobility spectrometry (FAIMS) to investigate the separation and identification of three xylene isomers. A homemade hollow needle-ring ion source was used, and five chemical modifiers, represented by methanol, ethanol, acetone, ethyl acetate, and acetic acid, were doped into the xylene target analytes to observe the separation and identification of the three isomers. This was based on the fact that the addition of helium and the increase of the RF voltage could no longer improve the resolution of the field asymmetric waveform ion mobility spectrometry system. The experimental results at an RF field voltage of 15 kV cm^-1 showed that the spectral peak shifts of o-, m-, and p-xylene in a normal nitrogen environment were -0.21, -0.21, and -0.24 V, respectively. o-Xylene showed a spectral peak of -1.33 V after the addition of helium; however, the separation was not evident. The FAIMS spectrum of xylene showed multiple cluster ion peaks upon addition of the chemical modifiers on top of helium. The alcohol chemical modifiers caused three spectral peaks, with the best effect for methanol, and the characteristic ion peak positions of -7.16, -6.90, and -6.01 V for o-, m-, and p-xylene, respectively. The separation using proton-based chemical modifiers was confirmed to be stronger than that using non-proton-based chemical modifiers, and appropriate volume fractions of chemical modifiers provided a better separation of the target analytes. This study introduces a novel concept and method for the separation and identification of xylene isomers.

Recent progress in the design, synthesis and applications of chiral metal-organic frameworks

Chiral Metal-Organic Frameworks (CMOFs) are unique crystalline and porous class of materials which is composed of organic linkers and metal ions. CMOFs surpass traditional organic and inorganic porous materials because of their tunable shape, size, functional diversity, and selectivity. Specific applications of CMOFs may be exploited by introducing desired functional groups. CMOFs have chiral recognition abilities, making them unique for chiral compound synthesis and separation. The CMOFs can be synthesized through different approaches. Two main approaches have been discussed, i.e., direct and indirect synthesis. Synthetic strategies play an essential role in getting desired properties in MOFs. CMOFs find potential applications in adsorption, asymmetric catalysis, luminescence, degradation, and enantioselective separation. The MOFs' porosity, stability, and reusability make them an attractive material for these applications. The plethora of applications of CMOFs have motivated chemists to synthesize novel MOFs and number of MOFs have been ever-escalating. Herein, the synthetic methods of CMOFs and their various applications have been discussed.

Poly(acrylic acid)/Fe3O4 Supported on MIL-100(Cr) MOF as a Novel and Magnetic Nanocatalyst for the Synthesis of Pyrido[2,3-d]Pyrimidines

In the current work, a convenient and simple approach for preparing poly (acrylic acid)/Fe₃O₄ supported on MIL-100(Cr) for the synthesis of pyrido [2,3-d]pyrimidine derivatives via the three-component one-pot reaction of 1,3-indandione, 6-amino uracil, and aromatic aldehydes is reported. The effectiveness of this new magnetic nanocatalyst was proved. The results showed this nanocatalyst's moderate to high yield under reflux conditions. SEM, TEM, IR, EDX, XRD, BET, and TGA were used to characterize the structure of the synthesized nanocatalyst. This synthetic protocol offers various advantages, including cost-saving, excellent yields in short reaction times (67–98%), low catalyst loading, and catalyst reusability.

Separation of pyrrolidine from tetrahydrofuran by using pillar[6]arene-based nonporous adaptive crystals

Pyrrolidine, an important feedstock in the chemical industry, is commonly produced via vapor-phase catalytic ammoniation of tetrahydrofuran (THF). Obtaining pyrrolidine with high purity and low energy cost has extremely high economic and environmental values. Here we offer a rapid and energy-saving method for adsorptive separation of pyrrolidine and THF by using nonporous adaptive crystals of per-ethyl pillar[6]arene (EtP6). EtP6 crystals show a superior preference towards pyrrolidine in 50 : 50 (v/v) pyrrolidine/THF mixture vapor, resulting in rapid separation. The purity of pyrrolidine reaches 95% in 15 min of separation, and after 2 h, the purity is found to be 99.9%. Single-crystal structures demonstrate that the selectivity is based on the stability difference of host-guest structures after uptake of THF or pyrrolidine and non-covalent interactions in the crystals. Besides, EtP6 crystals can be recycled efficiently after the separation process owing to reversible transformations between the guest-free and guest-loaded EtP6.

New insights into the selective adsorption mechanism of cationic and anionic dyes using MIL-101(Fe) metal-organic framework: Modeling and interpretation of physicochemical parameters

In the current study, iron-based metal organic framework (MOF) MIL-101(Fe) was successfully prepared via a facile solvothermal method. The as-synthesized MIL-101(Fe) was characterized by XRD, FE-SEM, FTIR, TGA and zeta potential techniques, and then employed as an adsorbent for methyl orange (MO) and methylene blue (MB) dyes. The adsorbed quantities of MO (1067 to 831 mg/g) were higher than those of MB (402 to 353 mg/g) indicating the high selectivity of MIL-101(Fe) towards the anionic dye at all temperatures (20-60 °C). Adsorption processes of MO and MB followed the pseudo-second order kinetics and the Langmuir equilibrium model. The interaction mechanism at a molecular level was analyzed and deeply interpreted via the advanced multilayer adsorption model. Steric parameters indicated that MO molecular aggregation (n) was 0.95-1.33 thus signifying the presence of multi-docking and multi-interactions mechanisms. The aggregated number of MB was superior to unity (i.e., n = 1.17-1.78) suggesting a vertical adsorption position and a multi-interactions mechanism at all operating temperatures. The density of MIL-101(Fe) active sites (D_{M =} 77.33-52.38 mg/g for MB and 149.91-107.07 for MO) and the total adsorbed dye layers (N_t = 3.12-2.49 for MB and 5.36-3.67 for MO) resulted in improving the adsorption capacities of MO dye. The adsorption energies ranged from 8.89 to 33.73 kJ/mol and they displayed that MO and MB uptake processes were exothermic controlled by physical interactions at all temperatures. Regeneration results indicated that this adsorbent can be reutilized without a significant loss in its removal efficiency after five adsorption-desorption cycles. Overall, the adsorption capacity, chemical stability, and regeneration performance of MIL-101(Fe) support its application as a very promising adsorbent for the removal of organic hazardous pollutants from water.

Mixed Metal-Organic Framework Stationary Phases for Liquid Chromatography

Strategic design of the stationary phase in liquid chromatography (LC) is crucial for modern separation science. Herein, a design approach using mixed metal-organic frameworks (MOFs) as tunable LC stationary phases is proposed. Three MOFs with an isostructural pillared-layer structure are employed, with pore sizes tuned by the systematic design of the constituent ligands, using 1,4-benzenedicarboxylate (bdc), 1,4-naphthalenedicarboxylate (ndc), and 9,10-anthracenedicarboxylate (adc). Packed columns filled with the MOFs and their mixed-particle/solid-solution stationary phases are prepared and examined for the retention capability of polyethylene glycol (PEG) in LC. While the MOF-packed columns filled with binary mixtures of different MOF particles provide good control of the retention with respect to the particle mixing ratio, the columns filled with mixed-linker solid-solution MOFs show a significant multicomponent effect on the retention behavior. Specifically, mixed-linker solid-solution MOFs consisting of bdc/ndc binary ligands are found to show a strong retention that surpasses even their parent MOFs, namely, pure bdc- and ndc-MOF stationary phases. The retention behavior on the MOF-packed columns is explained by the specific nanostructures of the solid-solution MOFs, which affects the balance between substrate affinity and adsorption kinetics into the MOF pores, dictating the total retention capability. The results provide an extra dimension for stationary phase design using MOFs as a promising recognition medium for LC.

Separation of p-xylene and m-xylene by simulated moving bed chromatography with MIL-53(Fe) as stationary phase

The separation of p-xylene (PX) and m-xylene (MX) isomers with near boiling points is a worldwide problem. The metal-organic framework material is an ideal stationary phase for chromatographic separation because of its high porosity, homogeneous pore diameter and good chemical stability. In this paper, a simulated moving bed (SMB) chromatography system with MIL-53(Fe) as the stationary phase and petroleum ether-dichloromethane as the mobile phase was designed to separate PX and MX at ambient temperature. Firstly, according to the elution curves of a single column, nonlinear competitive Langmuir adsorption isotherm equation was confirmed by equilibrium dispersive chromatography model. Then, the SMB separation zone was determined based on triangle theory, and the SMB operating conditions were optimized. Finally, the purity, recovery and productivity of PX reached 100.0%, 99.1% and 93.1 g/L/h, respectively; the purity, recovery and productivity of MX reached 96.4%, 100.0% and 23.5 g/L/h, respectively; the solvent consumption was 0.42 L/g.

Understanding the Working Mechanism of the NovelHKUST-1@BPS Composite Materials as Stationary Phases for Liquid Chromatography

Composite materials have been used based on coordination polymers or microporous metal-organic frameworks (MOFs) combined with mesoporous matrices for adsorption-related techniques, which enable outflanking some adverse phenomena manifested during pristine components operation and enhance the performance and selectivity of the resulting materials. In this work, for the first time, the novel HKUST-1@BPS composites synthesized by the microwave-assisted (MW) technique starting from microporous HKUST-1 (Cu₃(btc)₂) MOF and biporous silica matrix (BPS) with bimodal mesopore size distribution were comparatively studied as materials for liquid-phase adsorption techniques utilizing the high-performance liquid chromatography (HPLC) method and benzene as a model adsorbate. It was established that the studied HKUST-1@BPS composites can function as stationary phases for HPLC, unlike the pristine HKUST-1 and bare BPS materials, due to the synergetic effect of both components based on the preliminary enhanced adsorbate mass transfer throughout the silica mesopores and, subsequently, its penetrating into HKUST-1 micropores. The suggested mechanism involves the initial deactivation of open metal Cu²⁺ sites in the HKUST-1 framework structure by isopropanol molecules upon adding this polar component into the mobile phase in the region of the isopropanol concentration of 0.0 to 0.2 vol.%. Thereafter, at the medium range of varying the isopropanol concentration in the eluent of 0.2 to 0.3 vol.%, there is an expansion of the previously inaccessible adsorption centers in the HKUST-1@BPS composites. Subsequently, while further increasing the isopropanol volume fraction in the eluent in the region of 0.3 to 5.0 vol.%, the observed behavior of the studied chromatographic systems is similar to the quasi-normal-phase HPLC pattern. According to the obtained thermodynamic data, benzene adsorption into HKUST-1 micropores from solutions with a vol.% of isopropanol in the range of 0.4 to 5.0 follows the unique entropy-driven mechanism previously described for the MIL-53(Al) framework. It was found that HKUST-1 loading in the composites and their preparation conditions have pronounced effects on their physicochemical properties and adsorption performance, including the adsorption mechanism.

Preparation of Novel Chiral Stationary Phases Based on the Chiral Porous Organic Cage by Thiol-ene Click Chemistry for Enantioseparation in HPLC

Porous organic cages (POCs) are an emerging class of porous materials that have aroused considerable research interest because of their unique characteristics, including good solubility and a well-defined intrinsic cavity. However, there have so far been no reports of chiral POCs as chiral stationary phases (CSPs) for enantioseparation by high-performance liquid chromatography (HPLC). Herein, we report the first immobilization of a chiral POC, NC1-R, on thiol-functionalized silica using a mild thiol-ene click reaction to prepare novel CSPs for HPLC. Two CSPs (CSP-1 and CSP-2) with different spacers have been prepared. CSP-1, with a cationic imidazolium spacer, exhibited excellent enantioselectivity for the resolution of various racemates. Twenty-three and 12 racemic compounds or chiral drugs were well enantioseparated on the CSP-1-packed column under normal-phase and reversed-phase conditions, respectively, including alcohols, diols, esters, ethers, ketones, epoxides, organic acids, and amines. In contrast, chiral resolution using CSP-2 (without a cationic imidazolium spacer)-packed column B was inferior to that of column A, demonstrating the important role of the cationic imidazolium spacer for chiral separation. The chiral separation capability of column A was also compared with that of two most popular commercial chiral columns, Chiralpak AD-H and Chiralcel OD-H, which exhibits good chiral recognition complementarity with the two commercial chiral columns. In addition, five positional isomers dinitrobenzene, nitroaniline, chloroaniline, bromoaniline, and iodoaniline were also well separated on column A. The effects of temperature, mobile phase composition, and injected analyte mass for separation on column A were investigated. Column A also showed good stability and reproducibility after repeated injections. This work demonstrates that chiral POCs are promising chiral materials for HPLC enantioseparation.

Single-Crystalline Covalent Organic Frameworks as High-Performance Liquid Chromatographic Stationary Phases for Positional Isomer Separation

Vigorously developing new stationary phases to meet the requirements for the separation of positional isomers that have similar physicochemical properties is still an urgent topic in separation science. Herein, a single-crystalline covalent organic framework (COF-300) packed column for the separation of positional isomers in high-performance liquid chromatography (HPLC) was reported for the first time. Benefitting from its regular shape, excellent chemical and thermal stability, microporous feature, and strong hydrophobicity of single-crystalline COF-300, the single-crystalline COF-300-packed column showed excellent resolution for the separation of positional isomers, including nitroaniline, dichlorobenzene, dibromobenzene, diiodobenzene, diethylbenzene, chloronitrobenzene, bromonitrobenzene, and iodonitrobenzene isomers, which cannot be all separated on commercial columns and a polycrystalline COF-300-packed column. Especially, the resolution values for m-/p-diiodobenzene and o-/m-diiodobenzene were 4.45 and 2.53. Moreover, the alkylbenzene, monosubstituted aromatics, polycyclic aromatic hydrocarbons, and the mixture of ethylbenzene and styrene were also baseline separated on the single-crystalline COF-300-packed column. This successful application not only confirmed the great potential of single-crystalline COFs in HPLC separation of positional isomers but also pioneered the utilization of single-crystalline COFs in separation science.

Recent trends on the implementation of reticular materials in column‐centered separations

Advances in the development of column‐based analytical separations are strongly linked to the development of novel materials. Stationary phases for chromatographic separation are usually based on silica and polymer materials. Nevertheless, recent advances have been made using porous crystalline reticular materials, such as metal‐organic frameworks and covalent organic frameworks. However, the direct packing of these materials is often limited due to their small crystal size and nonspherical shape. In this review, recent strategies to incorporate porous crystalline materials as stationary phases for liquid‐phase separations are covered. Moreover, we discuss the potential future directions in their development and integration into suitable supports for analytical applications. Finally, we discuss the main challenges to be solved to take full advantage of these materials as stationary phases for analytical separations.

Hydrogel Coating with Temperature Response Retention Behavior and Its Application in Selective Separation of Liquid Chromatography

We reporte the double-layer hydrogel-coated mesoporous silica material as a new stationary phase for liquid chromatography. The method of combining physical coating and chemical coating was to apply hydrogel coating on the surface of silica, and finally, a new type of liquid chromatography stationary phase with in situ coating of the functional hydrogel on silica was obtained. This hydrogel-functionalized liquid chromatography stationary phase also exhibits a certain temperature responsiveness. Experimental results show that this temperature response is mainly due to changes in the hydrogen bonding between the stationary phase and the analyte at different temperatures in the column oven, which leads to changes in retention behavior. The hydrogel-coated mesoporous silica microspheres showed excellent selectivity for many polar analytes. An excellent column efficiency was obtained (139 000 plates/m for terephthalic acid) after optimization of chromatographic conditions. In addition to rapid separation of some analytes, this new hydrogel stationary phase also has certain superiority in chromatographic performance compared with other new excellent liquid chromatography stationary phases functioned by three-dimensional cross-linking systems. The important thing is that this strategy is relatively easy to prepare a new stationary phase with different properties.

An alternative strategy to construct uniform MOFs-Grafted silica core-shell composites as mixed-mode stationary phase for chromatography separation

The preparation of the metal-organic frameworks (MOFs)@silica core-shell microspheres as the stationary phases mainly relied on the method of electrostatic interaction between the metal ions of MOFs and the silanol groups. Herein, the ligands of MOFs were preferentially modified to the surface of silica as connection points and seed crystals to connect or form the MOFs. In this way, the evenness of the MOFs particles on the silica surface was effectively improved, and the prepared composites possessed excellent reproducibility and stability, including acid-base stability. The relative standard deviation of the retention time for repeatability ranged from 0.1% to 0.26% and for stability retention time from 0.3% to 0.6%. Compared with commercial columns, the prepared stationary phase showed enhanced separation selectivity for separation of both hydrophilic and hydrophobic compounds containing alkaloids, nucleosides, antibiotics and alkylbenzenes, etc. The obtained column was used as a matrix for fast separation and analysis of antibiotics in actual samples. In short, the composites showed superior reproducibility, stability and satisfactory separation performance towards a variety of compounds in the studied conditions. It also provided another way to improve the evenness of MOFs particles on the surface of silica and enhance the stability of them under polar conditions.

Revisiting molecular adsorption: unconventional uptake of polymer chains from solution into sub-nanoporous media

Adsorption of polymers from the solution phase has been extensively studied to cope with many demands not only for separation technologies, but also for the development of coatings, adhesives, and biocompatible materials. Most studies hitherto focus on adsorption on flat surfaces and mesoporous adsorbents with open frameworks, plausibly because of the preconceived notion that it is unlikely for polymers to enter a pore with a diameter that is smaller than the gyration diameter of the polymer in solution; therefore, sub-nanoporous materials are rarely considered as a polymer adsorption medium. Here we report that polyethylene glycols (PEGs) are adsorbed into sub-nanometer one-dimensional (1D) pores of metal-organic frameworks (MOFs) from various solvents. Isothermal adsorption experiments reveal a unique solvent dependence, which is explained by the balance between polymer solvation propensity for each solvent and enthalpic contributions that compensate for potential entropic losses from uncoiling upon pore admission. In addition, adsorption kinetics identify a peculiar molecular weight (MW) dependence. While short PEGs are adsorbed faster than long ones in single-component adsorption experiments, the opposite trend was observed in double-component competitive experiments. A two-step insertion process consisting of (1) an enthalpy-driven recognition step followed by (2) diffusion regulated infiltration in the restricted 1D channels explains the intriguing selectivity of polymer uptake. Furthermore, liquid chromatography using the MOFs as the stationary phase resulted in significant PEG retention that depends on the MW and temperature. This study provides further insights into the mechanism and thermodynamics behind the present polymer adsorption system, rendering it as a promising method for polymer analysis and separation.

Non-conjugated flexible network for the functional design of silica-based stationary phase for mixed-mode liquid chromatography

The functionalized non-conjugated organic network modified silica microspheres are proposed as the stationary phase of liquid chromatography, which can effectively avoid some defects of organic framework materials in liquid chromatography. Due to the co-existing of pyridine ring, carbonyl group, amide group and triazine ring in the non-conjugated flexible organic network on the silica surface, the developed mixed-mode stationary phase exhibits multiple interactions between the stationary phase and the analytes during the separation process. A variety of nucleoside bases, organic acids, antibiotics, pesticides, alkylbenzenes, polycyclic aromatic hydrocarbons and sulfonamides achieved ideal resolution and flexible selectivity in separation. Compared with the commercial chromatographic columns under their optimized chromatographic conditions, it shows better performance for the separation of complex analytes. The influence of chromatographic conditions on retention behavior indicates that the column's multiple retention mechanisms make it suitable for mixed-mode liquid chromatography. The stationary phase prepared by the new design strategy also has excellent chromatographic reproducibility, repeatability and stability with the intraday RSD of 0.09%-0.12% (n = 10) and the interday RSD of 0.37%-1.64% (n = 5) for the retention time. The separation results of actual samples also prove its potential in the analysis of complex samples. In short, we designed and prepared the non-conjugated flexible network modified silica stationary phase material for liquid chromatography that is different from organic framework materials. Its excellent separation ability shows that we have successfully reported a new kind of liquid chromatography packing with functional design and facile preparation method.

Metal-organic framework application for mercury speciation using solid phase extraction followed by direct thermal release-electrothermal atomization atomic absorption spectrophotometric detection (ETA AAS)

Metal-organic frameworks (MOFs) are increasingly used in analytical chemistry for pre-concentration of trace elements followed by their determination using modern analytical techniques. However, there are a limited number of publications concerning the use of MOFs for speciation purposes, while their structural and functional features are perspective for the element species selective extraction and pre-concentration. It is known that mercury refers to the most hazardous elements which species demonstrate different toxicity, migration routes and bioavailability as well. Consequently the development of new approaches for mercury speciation in environments remains an actual objective of analytical chemistry. In present work a new methodology for inorganic and organic mercury speciation in water was proposed. This approach is based on pre-concentration using solid phase extraction (SPE) followed by their determination directly from the solid phase with the application of the thermal release - electrothermal-atomic-absorption technique (TR-ETA-AAS). An original SPE-procedure based on the use of UIO-66 [Zr₆O₄(OH)₄(bdc)₆] in two different modes (non-modified and modified with cysteine) as a sorbent was designed. As a result of SPE as well as TR-ETA-AAS optimization the detection limits (LOD) for all listed species at the level of 0.06 μg L^-1 have been achieved. It was also shown that the presence of the other elements (K, Na, Ca, Mg at the level of 100 μg L^-1, and Mn, Fe, Cr, Al, Zn, Cd, Pb - of 25 μg L^-1) does not affect the results obtained. The developed assay demonstrates a high efficiency, low LODs, wide linear range and admissible analysis duration. The reliability of the data obtained was confirmed by the standard addition approach and by a comparison with the results of independent analytical methods.

A novel approach for the preparation of core-shell MOF/polymer composites as mixed-mode stationary phase

The nickel organic framework capped with polyvinylpyrrolidone was prepared and synergistically immobilized onto porous silica surface as the mixed-mode stationary phase for high-performance liquid chromatography. Here, polyvinylpyrrolidone firstly was chosen as functional molecules to change morphology and size of the metal organic framework. The silica microspheres were then modified by them via a simple bonding method rather than in-situ growth method with the aid of electrostatic interaction commonly used before. The stationary phase showed flexible selectivity for separation of both hydrophilic and hydrophobic compounds, especially for hydrophilic compounds such as carbohydrates, alkaloids and sulfonamides etc. The chromatographic behaviors were evaluated by investigating various factors, and a typical mixed-mode retention feature of the column was observed. The composites could be prepared repetitively, and relative standard deviations of retention time of objective compounds among different batches were less than 1.75%. It also showed excellent chromatographic reproducibility, stability and potentiality for application in real samples. In short, the composites can be used for a feasible option for analysis of multiple compounds as the mixed-mode stationary phase and it provides a general approach for preparing MOFs-based composites by changing morphology and size of MOFs.

Fabrication of microporous organic network@silica composite for high-performance liquid chromatographic separation of drugs and proteins

Microporous organic networks (MONs) that exhibit good stability and hydrophobicity are promising candidates for performing HPLC separation of small organic compounds. However, their applications in separating large analytes as well as biomolecules are still limited by the microporous nature of MONs. Herein, we demonstrated the fabrication of a MON-functionalized silica (MON@SiO₂ ), exhibiting micro and mesopores for the HPLC separations of small drugs as well as large analytes, such as flavones, nonsteroidal anti-inflammatory drugs (NSAIDs), endocrine disrupting chemicals (EDCs), and proteins. MON was successfully modified on SiO₂ microspheres to yield the uniform and mono-dispersed MON@SiO₂ . The separation mechanisms and performance of the MON@SiO₂ packed column were evaluated for a wide range of analytes, including neutral, acidic, basic compounds, drugs, and proteins. Compared with commercial C18 and SiO₂ -NH₂ packed columns, the proposed MON@SiO₂ column afforded superior performance in the separations of flavones, NSAIDs, EDCs, and proteins. Moreover, the MON@SiO₂ column also offered good repeatability with intraday RSDs (n = 7) of <0.1%, <2.0%, <2.3%, and <0.7% for the retention time, peak height, peak area, and half peak width, respectively, for separating EDCs. This work proved the potential of using MONs in the HPLC separations of drugs and proteins.

Visual recognition of ortho-xylene based on its host-guest crystalline self-assembly with α-cyclodextrin

HYPOTHESIS

Distinguishing substituted aromatic isomers is a challenging task because of the great similarity of their physicochemical properties. Considering xylene isomers have drastically different geometrical shapes, we predict this would show great impact on the self-assembling behavior of various xylene isomer@cyclodextrin inclusion complex.

EXPERIMENTS

Through host-guest crystalline self-assembly, among three isomers, only ortho-xylene is capable to form hydrogels with α-cyclodextrin. ROESY NMR, molecular simulations and circular dichroism spectra suggest that the ortho selectivity comes from the difference in the conformation of host-guest building block. The larger volume, and steric hinderance of the ortho isomer make it most possibly decrease their tendency to adopt more mobile orientations in cyclodextrin-based complex as meta and para isomers do, resulting in gel formation.

FINDINGS

Herein, we report a novel, facile and environmentally-friendly protocol on the recognition of ortho benzene isomers using α-cyclodextrin through host-guest crystalline self-assembly. Visual recognition of ortho-xylene is achieved through amplifying the structural difference of xylene isomers at molecular scale into macroscopic scale. We believe this work unveils subtle rules to control macroscopic assemblies at the molecular level and highlights the potential of using macrocyclic compounds to improve the quality and reduce the energy bill for separation in petrochemical industry.

Regulating metal-organic frameworks as stationary phases and absorbents for analytical separations

Metal-organic frameworks (MOFs) are highly ordered framework systems composed of metal centers and organic linkers formed through coordination bonds. The diversity of metal elements and easily modified organic ligands, together with controllable synthetic approaches, gives rise to the designability of various MOF structures and topologies and the capability of MOFs to be functionalized. Their structural diversity provides MOFs with many unique properties, such as permanent porosity, flexible structures, thermostability, and high adsorption capacity, leading to great practicability in technical applications. In this review, we concentrate on the applications of MOFs in the field of gas chromatography, high-performance liquid chromatography, and the enrichment of biomolecules, based on rational arrangements in the structures and functions of MOFs. Moreover, we emphasize the importance of structural and chemical regulations for the improvement of separation efficiency.

Metal-Organic Frameworks for Liquid Phase Applications

In the last two decades, metal-organic frameworks (MOFs) have attracted overwhelming attention. With readily tunable structures and functionalities, MOFs offer an unprecedentedly vast degree of design flexibility from enormous number of inorganic and organic building blocks or via postsynthetic modification to produce functional nanoporous materials. A large extent of experimental and computational studies of MOFs have been focused on gas phase applications, particularly the storage of low-carbon footprint energy carriers and the separation of CO2-containing gas mixtures. With progressive success in the synthesis of water- and solvent-resistant MOFs over the past several years, the increasingly active exploration of MOFs has been witnessed for widespread liquid phase applications such as liquid fuel purification, aromatics separation, water treatment, solvent recovery, chemical sensing, chiral separation, drug delivery, biomolecule encapsulation and separation. At this juncture, the recent experimental and computational studies are summarized herein for these multifaceted liquid phase applications to demonstrate the rapid advance in this burgeoning field. The challenges and opportunities moving from laboratory scale towards practical applications are discussed.

Design and evaluation of novel MOF-polymer core-shell composite as mixed-mode stationary phase for high performance liquid chromatography

A general method was developed for preparing a metal-organic framework-polymer composite coated silica core-shell stationary phase. Silica microspheres were comodified with metal-organic framework and polyvinylpyrrolidone rather than the in situ method of silica modification by original metal-organic framework particles. Metal-organic framework particles and polyvinylpyrrolidone on silica surface were beneficial to suppress silanol activity and enhance composite material tolerance, as well as increasing the water compatibility of the original metal-organic framework-based stationary phases. The stationary phase exhibited superior hydrophilic and hydrophobic performance in terms of separation for various analytes including seven alkaloids, six sulfonamides, five antibiotics, and five polycyclic aromatic hydrocarbons. Moreover, the composite material also showed excellent stability with the relative standard deviation of the retention time of 0.4 to 0.7%. The separation performance with real samples proved that the column has good practical application potential. In summary, the poposed method provides a general way for preparing metal-organic framework-polymer composite material and changed the current status of original metal-organic framework particles modified silica as a single mode chromatographic stationary phase.