Tin speciation in the femtogram range in open ocean seawater by gas chromatography/inductively coupled plasma mass spectrometry using a shield torch at normal plasma conditions

Quantification of tributyltin in seawater using triple isotope dilution gas chromatography-inductively coupled plasma mass spectrometry achieving high accuracy and complying with European Water Framework Directive limits

A triple isotope dilution GC-ICPMS method for the determination of tributyltin (TBT) was developed and validated to meet the European Water Framework Directive (WFD) requirements. The validation procedure involved the evaluation of trueness, precision (repeatability, intermediate precision), limit of detection (LOD) and limit of quantification (LOQ), stability, measurement uncertainty and traceability studies. The method is one of the most sensitive methods published to date with good accuracy, 103% average recovery in the range with %RSDs of 2.8-6.7%. A LOD value of 0.015 ng L^-1 for the TBT cation was achieved with a sample volume of 12 mL seawater. TBT was derivatized using 20 µL sodium tetraethylborate solution (0.05% NaBEt₄) to make volatile for GC-ICPMS. Measurement uncertainty was in the range of 4.8-13% which was achieved through dissolution of tributyltinchloride (TBTCl) in 1-propanol, a low-volatility solvent combined with the use of a triple isotope dilution (ID) calibration technique. Isotope dilution calibration was performed by adding ¹¹⁷Sn isotopically enriched TBT to the seawater samples. The stability test results showed that TBT concentration was stable for three months in seawater samples after passing through a 0.2 µm filter and stored in amber glass bottles at 4°C. The response surface methodology (RSM) approach was successfully implemented to provide optimal conditions for large volume injection (LVI) to obtain the maximum analytical signal. The key variables selected in the experimental design were evaporation time, evaporation temperature, carrier flow, and injection speed. This method was applied to seawater samples collected from the Bay of Izmit, Kocaeli, Turkey, where TBT pollution has not been measured yet.

Dissolved inorganic tin sources and its coupling with eco-environments in Bohai Bay

Dissolved inorganic tin (DISn) and its spatial variation were examined in Bohai Bay seawaters to understand the DISn behavior and pollution in this area. DISn concentration gradually increased with the distance from the coast and showed a slight decrease with the increasing depth from surface water, suggesting the scavenged behavior of tin with an atmospheric input to surface water. Besides, the higher DISn values also were found near the Haihe Estuary inferring that the riverine input was a source of DISn. Based on the data in this study, a preliminary estimate of the tin budget via riverine input and atmospheric deposition has been established. According to our estimate, about 2 × 10(6) and 8.47 × 10(5) g/year of tin reach Bohai Bay via rivers and atmosphere. Environmental factors such as suspended particulate material, salinity, total organic matter, pH, nutrients, and phytoplankton had the important influences on DISn distribution. Among them, the negative correlation between DISn and phytoplankton at most stations might indicate the biological uptake of tin.

Environmental analysis by inductively coupled plasma mass spectrometry

This article reviews the numerous ways in which inductively coupled plasma mass spectrometry has been used for the analysis of environmental samples since it was commercially introduced in 1983. Its multielemental isotopic capability, high sensitivity and wide linear dynamic range makes it ideally suited for environmental analysis. Provided that some care is taken during sample preparation and that appropriate calibration strategies are used to circumvent non-spectroscopic interferences, the technique is readily applicable to the analysis of a wide variety of environmental samples (natural waters, soils, rocks, sediments, vegetation, etc.), using quadrupole, time-of-flight or double-focusing sector-field mass spectrometers. In cases where spectroscopic interferences arising from the sample matrix cannot be resolved, then separation methods can be implemented either on- or off-line, which can simultaneously allow analyte preconcentration, thus further decreasing the already low detection limits that are achievable. In most cases, the blank, prepared by following the same steps as for the sample but without the sample, limits the ultimate detection limits that can be reached.

On-line solid-phase extraction coupled with liquid chromatography/electrospray ionization mass spectrometry for the determination of trace tributyltin and triphenyltin in water samples

On-line solid-phase extraction (SPE) for pre-concentration and sample cleanup is one strategy to reduce matrix effects and to simultaneously improve detection sensitivity in liquid chromatography/mass spectrometry (LC/MS). This paper describes an on-line SPE-LC/MS method for the determination of tributyltin (TBT) and triphenyltin (TPhT) at trace levels in water samples. The direct coupling of an on-line C18 pre-column to LC/MS was used to pre-concentrate TBT and TPhT at trace levels from waters and to remove interfering matrix effects. Pre-concentration was followed by separation of TBT and TPhT on a C18 column using a mobile phase containing 0.1% (v/v) HCOOH/5 mM HCOONH4 and methanol. While both electrospray ionization (ESI) and atmospheric pressure chemical ionization (APCI) can be interfaced with MS for the detection of TBT and TPhT, ESI-MS was preferred for this application. The calibration curve for the targets was linear in the concentration range 0.1-30 microg L(-1). The detection limit (signal-to-noise (S/N) ratio = 3) was 0.02 microg L(-1) when 3.0 mL of sample was enriched on the C18 pre-column. The recoveries of TBT and TPhT in spiked waters were from 81.0 to 101.9%. The reproducibilities for the analysis of the standard mixture (10 microg L(-1)) for TBT and TPhT were 13.1 and 5.0%, respectively. The developed method was an easy and fast way to analyze TBT and TPhT in water samples.

Ultraviolet degradation of methyltins: elucidating the mechanism by identification of a detected new intermediary product and investigating the kinetics at various environmental conditions

The photodegradation of methyltins, as environmental pollutants, has scarcely been studied so far because of the shortage of rapid and sensitive speciation methods, even though they have very simple structures. The photodegradation of monomethyltin trichloride (MMT), dimethyltin dichloride (DMT) and trimethyltin chloride (TMT) was studied with our new developed HPLC-FPD hyphenated system, which enables rapid and sensitive detection of methyltins. The half-life times and kinetic rate constants of their degradation at different pH were calculated. The results suggest that MMT, DMT and TMT can be degraded under the UV irradiation rapidly at different pH, with a degradation rate sequence of TMT<DMT<MMT. An unknown intermediary product, which is more stable and has higher concentration at pH 8 for MMT and DMT, of methyltin photodegradation was detected for the first time. This unknown intermediary product was identified as methyloltin with electrospray mass spectrometry, and the possible mechanism was proposed based on the intermediary product. The effects of some environmental parameters such as salinity and humic acid on the degradation rate of methyltins were also investigated. Results suggest that salinity and humic acid have strong effect on their degradation, especially for TMT, which was almost never degraded in the solutions containing NaCl and humic acid.

Environmental levels, toxicity and human exposure to tributyltin (TBT)-contaminated marine environment. a review. b_antizar@hotmail.com

Tributyltin (TBT) is a toxic chemical used for various industrial purposes such as slime control in paper mills, disinfection of circulating industrial cooling waters, antifouling agents, and the preservation of wood. Due to its widespread use as an antifouling agent in boat paints, TBT is a common contaminant of marine and freshwater ecosystems exceeding acute and chronic toxicity levels. TBT is the most significant pesticide in marine and freshwaters in Europe and consequently its environmental level, fate, toxicity and human exposure are of current concern. Thus, the European Union has decided to specifically include TBT compounds in its list of priority compounds in water in order to control its fate in natural systems, due to their toxic, persistent, bioaccumulative and endocrine disruptive characteristics. Additionally, the International Maritime Organization has called for a global treaty that bans the application of TBT-based paints starting 1 of January 2003, and total prohibition by 1 of January 2008. This paper reviews the state of the science regarding TBT, with special attention paid to the environmental levels, toxicity, and human exposure. TBT compounds have been detected in a number of environmental samples. In humans, organotin compounds have been detected in blood and in the liver. As for other persistent organic pollutants, dietary intake is most probably the main route of exposure to TBT compounds for the general population. However, data concerning TBT levels in foodstuffs are scarce. It is concluded that investigations on experimental toxicity, dietary intake, potential human health effects and development of new sustainable technologies to remove TBT compounds are clearly necessary.

Preparation, preservation and application of pure isotope-enriched phenyltin species

A method combining liquid/liquid extraction and chromatographic fractionation has been developed for the preparation of pure monophenyltin (MPhT), diphenyltin (DPhT), and triphenyltin (TPhT), synthesized from isotope-enriched Sn metal using phenylation of SnI(4) in diethylether (DEE) followed by quenching with HBr and water. After two successive extractions of the aqueous HBr phase with DEE, >99% of both DPhT and TPhT was recovered in the combined DEE phase and 94% of the MPhT remained in the aqueous phase. The MPhT in the aqueous phase was extracted into dichloromethane. The organic phases were vaporized and the PhTs were redissolved in MeOH/water/acetic acid/sodium acetate (59/30/6/8, v/v/v/w), which was also used as storing solution. Aliquots of the two solutions containing either DPhT and TPhT or MPhT were injected into a silica-based C(18) column for isolating and purifying single species. The yields of pure MPhT, DPhT, and TPhT, each synthesized from isotope-enriched (118)Sn metal, (122)Sn metal, and (124)Sn metal, were better than 99%. After chromatographic separation, the single phenyltin compounds were mixed to prepare a spike for multiple-isotope species-specific isotope dilution (MI-SSID). MI-SSID was successfully used to determine phenyltin compounds in the certified reference material, mussel tissue BCR CRM-477. At -20 degrees C, all of the fractionated phenyltin species were stable in the storage solution for at least 197 days. When these standards were stored at 4 degrees C or 22 degrees C, 4-6% of the DPhT and TPhT degraded within 27 days. The degradation of DPhT and TPhT increased with the ionic strength and acidity of the storage solution.

Organotin speciation in environmental matrices by automated on-line hydride generation-programmed temperature vaporization-capillary gas chromatography–mass spectrometry detection

In the present contribution, a new automated on-line hydride generation methodology was developed for dibutyltin and tributyltin speciation at the trace level, using a programmable temperature-vaporizing inlet followed by capillary gas chromatography coupled to mass spectrometry in the selected ion-monitoring mode acquisition (PTV-GC/MS(SIM)). The methodology involves a sequence defined by two running methods, the first one configured for hydride generation with sodium tetrahydroborate as derivatising agent and the second configured for speciation purposes, using a conventional autosampler and data acquisition controlled by the instrument's software. From the method-development experiments, it had been established that injector configuration has a great effect on the speciation of the actual methodology, particularly, the initial inlet temperature (-20 degrees C; He: 150 ml/min), injection volume (2 microl) and solvent characteristics using the solvent venting mode. Under optimized conditions, a remarkable instrumental performance including very good precision (RSD < 4%), excellent linear dynamic range (up to 50 microg/ml) and limits of detection of 0.12 microg/ml and 9 ng/ml, were obtained for dibutyltin and tributyltin, respectively. The feasibility of the present methodology was validated through assays upon in-house spiked water (2 ng/ml) and a certified reference sediment matrix (Community Bureau of Reference, CRM 462, Nr. 330 dibutyltin: 68+/-12 ng/g; tributyltin: 54+/-15 ng/g on dry mass basis), using liquid-liquid extraction (LLE) and solid-phase extraction (SPE) sample enrichment and multiple injections (2 x 5 microl) for sensitivity enhancement. The methodology evidenced high reproducibility, is easy to work-up, sensitive and showed to be a suitable alternative to replace the currently dedicated analytical systems for organotin speciation in environmental matrices at the trace level.

Determination of organotin compounds in water by headspace solid phase microextraction with gas chromatography–mass spectrometry

This investigation evaluates headspace solid-phase microextraction (HS-SPME) coupled with gas chromatography-mass spectrometry (GC-MS) to determine trace levels of organotins in water. The organotins were derivatized in situ with sodium tetraethylborate and adsorbed on a poly(dimethysiloxane) (PDMS)-coated fused silica fiber. The SPME experimental procedures to extract organotins in water were at pH 5, with extraction and derivatization simultaneously at 45 degrees C for 30 min in a 2% sodium tetraethylborate solution and a sample solution volume in the ratio of 1:1, and desorption in the splitless injection port of the GC at 260 degrees C for 2 min. Detection limits are determined to be in the low ng/L range. According to the analysis, the linearity range is from 10 to 10,000 ng/L with R.S.D. values below 12% except triphenyltin (24%). The proposed method was tested by analyzing surface seawater from the harbors on the Taiwanese coast for organotins residues. Some organotins studied were detected in the analyzed samples. Results of this study demonstrate the adequacy of the headspace SPME-GC-MS method for analyzing organotins in sea water samples.

Applicability of solid-phase microextraction combined with gas chromatography atomic emission detection (GC-MIP AED) for the determination of butyltin compounds in sediment samples

The performance of solid-phase microextraction (SPME) applied to the determination of butyltin compounds in sediment samples is systematically evaluated. Matrix effects and influence of blank signals on the detection limits of the method are studied in detail. The interval of linear response is also evaluated in order to assess the applicability of the method to sediments polluted with butyltin compounds over a large range of concentrations. Advantages and drawbacks of including an SPME step, instead of the classic liquid-liquid extraction of the derivatized analytes, in the determination of butyltin compounds in sediment samples are considered in terms of achieved detection limits and experimental effort. Analytes were extracted from the samples by sonication using glacial acetic acid. An aliquot of the centrifuged extract was placed on a vial where compounds were ethylated and concentrated on a PDMS fiber using the headspace mode. Determinations were carried out using GC-MIP AED.

Contamination and Biomethylation of Organotin Compounds in Pearl/Fish Culture Areas in Japan

Uwakai of Japan is famous for pearl and yellowtail fish culture. Recently, pearl culture farming in that region has suffered from a low production of pearls. An illegal use of organotin antifouling paints on fishing nets was reported. In the line of pollution studies, thus, the present investigation was carried out to examine the contamination status and fate of organotin compounds. Totally, 23 water, 10 sediment and 8 pearl oyster tissue samples were analyzed for tributyltin (TBT), triphenyltin (TPT), and their breakdown products (di- and mono compounds) by gas chromatography combined with inductively coupled plasma mass spectrometry (GC/ICP-MS). The results show that the TBT concentrations in water, sediment and biota were in the range from 0.11 to 10.6 ng Sn l(-1), 0.35 to 2500 ng Sn g(-1), and 50.4 to 181 ng Sn g(-1), respectively. The values for sediment and biota are expressed on the dry-weight basis. Triphenyltin in water, sediment and biota were in the range from 0.009 to 0.108 ng l(-1), non-detect to 12.7 ng g(-1), and non-detect to 6.83 ng g(-1), respectively. Although the TBT concentration in seawater is below the tentative assessment level of 10 ng l(-1) set by the Japanese Environment Agency in 1992, it may cause endocrine disruption/other effects in aquatic organisms. Octyltin compounds (mono-, di- and trioctyltin) were also quantified in seawater and sediment. The detection of dibutyldimethyltin (DBDMT) and tributylmonomethyltin (TBMMT) in sediment (methylated butyltins comprised 2.8-31% of total butyltins), and TBMMT in seawater suggested that biomethylation of anthropogenic tributyltins is a significant transformation pathway in the coastal environment.

Liquid chromatography-hydride generation-atomic absorption spectrometry for the speciation of tin in seafoods

Liquid chromatography with hydride generation atomic absorption spectrometry as the detection system was applied to the separation and determination of inorganic tin, tributyltin, dibutyltin, monobutyltin, diphenyltin and monophenyltin. A reversed phase C18 column and a methanol/water/acetic acid (70:27:3, v/v/v) mixture containing 0.05%(v/v) triethylamine and 0.1%(w/v) tropolone as the mobile phase (isocratic elution) were used. Extraction of organotins from the samples was carried out using methanol containing 0.05%(w/v) tropolone, a process that was repeated twice. The supernatants were shaken with water and dichloromethane in a separating funnel and the organic phase was collected and evaporated to dryness. When the method was applied to the speciation of tin in fresh and canned mussels, no organotins above the detection limits were identified in any of the samples, inorganic tin being the only species detected. The reliability of the procedure was checked by analyzing the total tin content of the samples by electrothermal atomic absorption spectrometry and by speciation of tin in a certified reference material, mussel tissue (CRM 477). The method can be used for environmental monitoring of organotins contaminated samples.

Effects of gamma-sterilization on butyltin homogeneity and content in sediments: a GC-ICP-MS study

A GC-ICP-MS method based on extraction and alkylation of butyltins with sodium tetraethylborate was used to quantitatively assess the fate of these analytes in solutions and sediments following exposure to gamma-irradiation. The effects of a 2.5 Mrad sterilization dose on three butyltin species in both methanolic calibration solutions and in sediment matrices were investigated. Although significant losses of tributyltin (TBT, 90%), dibutyltin (DBT, 100%) and monobutyltin (MBT, 80%) were detected in standard solutions prepared in methanol following gamma-irradiation, no species inter-conversion occurred. Some degradation of TBT (38%) and DBT (32%) but no significant change in MBT content was found using a spiked sediment CRM HISS-1. Conversion DBT to MBT in spiked HISS-1 was deduced. Much smaller degradation of TBT (16% loss) and 10% loss of DBT by conversion to MBT (14% gain) was registered using a sediment blend of PACS-2 and HISS-1 (SOPH). Despite some initial losses of TBT and DBT due to irradiation, better than 2% RSD in both TBT and DBT concentrations measured in twelve different bottles of blended sediment SOPH were obtained, indicating the material may be considered homogeneous for these analytes. Results from a long-term five-year stability study of PACS-2 show that all three butyltins are stable during storage at 4 degrees C followed with 2.5 Mrad minimum dose of gamma-irradiation sterilization treatment.

Comparison of different liquid chromatography conditions for the separation and analysis of organotin compounds in mussel and oyster tissue by liquid chromatography-inductively coupled plasma mass spectrometry

In this paper, a new high-performance liquid chromatography-inductively coupled plasma mass spectrometry (HPLC-ICP-MS) methodology for the analysis of organotin compounds in complex matrices is described. Earlier studies had failed to show baseline resolution between dibutyltin (DBT) and triphenyltin (TPhT). The data presented in this paper show that, by using a different C-18 stationary phase material (Ace C-18) with decreased particle size, baseline resolution of DBT and TPhT can be achieved, with the resultant separation of a third interfering component. In addition, the Ace C-18 stationary phase yields a significant increase in the number of theoretical plates, and, combined with changes in the mobile phase composition, a reduction in run-time by approximately 25%. It is shown that the minor compounds detected are present in the sample and not artefacts of the analytical procedure. The accuracy and precision of the proposed HPLC-ICP-MS method was demonstrated for the determination of TBT in oyster tissue during the BCR "MULSPOT" international interlaboratory certification project.

Gas chromatography-high-resolution mass spectrometry based method for the simultaneous determination of nine organotin compounds in water, sediment and tissue

A GC-HRMS based method for the accurate and sensitive determination of nine organotin compounds, tetrabutyltin (TeBT), tributyltin (TBT), dibutyltin (DBT), monobutyltin (MBT), triphenyltin (TPhT), diphenyltin (DPhT), monophenyltin (MPhT), tricyclohexyltin (TCyT), and dicyclohexyltin (DCyT) in sediment, tissue and water samples is presented and discussed. Mass spectral features of these analytes via both low resolution quadrupole and high resolution magnetic sector, GC-HRMS conditions under selective ion monitoring mode and QA/QC criteria for the positive identification of analyte are all provided. Linearity of response and minimal detectable limits are illustrated for each of the nine compounds monitored and the estimates of method limits-of-detection were 7-29 ppt for water and 0.35-1.45 ppb for tissue or sediments. Sample preparation considerations and precision are discussed for spiked water and sediment samples, whereas method accuracy was established by analysing a certified reference material (CRM) mussel sample and comparing our results to the assigned values. Good agreement was found between our results and assigned or indicative values for MBT, DBT, TBT, DPhT and TPhT (cyclohexyl-tins were not present in the CRM).

Elemental speciation by chromatographic separation with inductively coupled plasma mass spectrometry detection

Separation techniques coupled to inductively coupled plasma mass spectrometry (ICP-MS) is reviewed. ICP-MS technique is described briefly. Coupling of the different separation techniques are described, together with the most common applications used for each technique that has been described in the literature. An overview for the future of separation techniques coupled to ICP-MS with regard to elemental speciation is discussed.

Rapid determination of butyltin species in water samples by multicapillary gas chromatography with atomic emission detection following headspace solid-phase microextraction

A procedure for the rapid determination of mono-, di- and tributyltin in water samples is described. The analytes are simultaneously ethylated and concentrated on a solid-phase microextraction fibre placed in the headspace over the sample for 2 min. The ethylated species are then separated and selectively quantified in only 90 s using a multicapillary gas chromatography column combined with atomic emission detection. The influence of blank signals and sampling conditions on the sensitivity of the method is described. Detection limits of 1-5 ng/l and relative standard deviations of 6-10% at concentrations of 20 ng/l were obtained.

Analysis of organotin compounds by grignard derivatization and gas chromatography-ion trap tandem mass spectrometry

The determination of organotin compounds in water using gas chromatography-tandem mass spectrometry (GC-MS-MS) is described. Several organotin derivatives were synthesized by the reaction of organotin chlorides with Grignard reagents such as methyl-, propyl- and pentylmagnesium halides. After the optimization of the GC-MS-MS conditions, several derivatizations with the Grignard reagents were compared by evaluating the molar responses and volatilities of the derivatives and derivatization yields. As a result, the derivatizing reagent of choice is pentylmagnesium bromide. Calibration curves for the mono-, di- and tributyltins and mono-, di- and triphenyltins with pentylmagnesium bromide were linear in the range of 0.5-100 pg of Sn. The instrumental detection limits of six organotins ranged from 0.20 to 0.35 pg of Sn. The recovery tests from water samples (500 ml) were performed by using sodium diethyldithiocarbamate (DDTC) as a complexing reagent. Except for monophenyltin, the absolute recoveries of organotins from pure water at 200 ng of Sn/l were satisfactory. The recoveries calibrated by surrogate compounds (perdeuterated organotin chlorides) ranged from 71 to 109%. The method detection limits ranged from 0.26 to 0.84 pg of Sn (500-ml sample). This method was applied to the recovery of organotins from river water and seawater. The calibrated recoveries were between 90 and 122%.

Laser-enhanced ionization and laser-induced atomic fluorescence as element-specific detection methods for gas chromatography. Application to organotin analysis

We have demonstrated that flame laser-enhanced ionization (LEI) and flame laser-induced atomic fluorescence (LIAF) techniques can be used as, alternative sensitive detectors for gas chromatographic (GC) analysis of organotin compounds. These two element-specific detection methods are free from interferences from the organic solvent. Two types of LEI schemes for Sn detection are employed. For the two-step LEI scheme (TLEI), the tin atoms in the flame were stepwise excited and then ionized collisionally. In contrast, in detection with the single-step LEI scheme (SLEI), only one dye laser is used. For the analysis of tetramethyltin and tetraethyltin, the GC-TLEI, GC-SLEI, and GC-LIAF systems yield linear dynamic ranges of 0.015-400, 0.39-600 and 0.5-600 ng, respectively. The corresponding detection limits reach 0.15, 3.9 and 5.0 mg/l, with absolute quantities corresponding to 15, 390 and 500 pg, respectively, for an injection volume of 0.1 microl. These detection methods prove to be more sensitive and selective than the conventional flame ionization detection, which achieves absolute detection limits of 800 and 1667 pg for tetraethyltin and tetramethyltin, respectively, under identical GC conditions.