Ultrasensitive Controlled Release Aptasensor Using Thymine–Hg2+–Thymine Mismatch as a Molecular Switch for Hg2+ Detection

Tunable aptamer-MXene sensing interface for label-free and real-time detection of toxic pollutants in water samples

Stable and low-cost field-effect transistor (FET)-based biosensors are vital for the on-site detection of toxic pollutants in environmental monitoring applications. In this study, a tunable aptamer-MXene sensing interface was constructed to develop renewable FET biosensors. This was achieved through the reversible disulfide bond (-S-S-) reaction between the SH-Ti3C2Tx film and thiolated aptamer. Ti3C2Tx film was prepared using layer-by-layer assembly of Ti3C2Tx flakes and used as the conductance channel of this FET device. Then, dithiothreitol modification was carried out through the formation of Ti-S bonds. The reversible -S-S- bonds enabled the repeated regeneration of SH-Ti3C2Tx, which allowed deferent aptamers to be immobilized. Therefore, multiple targets could be detected with the same FET device, avoiding device-to-device variations. Three specific aptamers for microcystin-LR, β-lactam-resistant gene (β-ARG), and Hg2+ were adopted to demonstrate this characteristic. The prepared aptamer-MXene FET biosensor showed high sensitivity, repeatability and stability. Furthermore, a strong real-time response was observed upon exposure to the targets. This study demonstrated that constructing a tunable aptamer-MXene sensing interface is an efficient strategy for constructing cheap and renewable aptamer-MXene FET biosensors for the label-free and real-time detection of toxic pollutants.

A Review of Current Developments in Functionalized Mesoporous Silica Nanoparticles: From Synthesis to Biosensing Applications

Functionalized mesoporous silica nanoparticles (MSNs) have been widely investigated in the fields of nanotechnology and material science, owing to their high surface area, diverse structure, controllable cavity, high biocompatibility, and ease of surface modification. In the past few years, great efforts have been devoted to preparing functionalized MSNs for biosensing applications with satisfactory performance. The functional structure and composition in the synthesis of MSNs play important roles in high biosensing performance. With the development of material science, diverse functional units have been rationally incorporated into mesoporous structures, which endow MSNs with design flexibility and multifunctionality. Here, an overview of the recent developments of MSNs as nanocarriers is provided, including the methodologies for the preparation of MSNs and the nanostructures and physicochemical properties of MSNs, as well as the latest trends of MSNs and their use in biosensing. Finally, the prospects and challenges of MSNs are presented.

Hydrothermal Fabrication of Efficient Binary Pd/Ag2S Heterojunction Composites: Synthesis, Characterization, and Fluorometric Selective Sensing of Organophosphate Pesticides

Although many plasmonic nanosensors have been established for the detection of analytes, few of them are feasible for analyzing natural samples with very complex matrices because of insufficient method selectivity. To address this challenge, we propose an epitaxial and lattice-mismatch approach to the synthesis of a unique Pd/Ag2S nanostructure, which consists of a Pd segment with excellent plasmonic characteristics, and a highly stable Ag2S portion with minimum solubility product (Ksp(Ag2S) = 6.3 × 10- 50). Hence, Ag2S nanoparticles (NPs) and optimized (10.05 mmol/L) Pd/Ag2S composite were prepared using a hydrothermal method. The fabricated samples were characterized using different tools including UV-vis DRS, PL, powder XRD, TEM, and BET surface area measurements. Furthermore, the fluorometric sensing performance of the Ag2S and Pd/Ag2S samples was examined in the detection of organophosphate pesticides such as MLT, PRT, DZN, FNT, DCL, MCP, and CPS pesticides at room temperature. The quantitative detection of MLT, PRT, DZN, FNT, DCL, MCP, and CPS pesticides was achieved based on the Pd/Ag2S composite and organophosphate group-specific interaction. The optimized sensor exhibited a lower limit of detection (3.08 µM), excellent reproducibility, selectivity, and stability with an enhanced sensitivity of - 207.1 µA/µM cm2 (R2 = 0.98) in the range of 10 µM-100 µM for the detection of CPS pesticide. In addition, the fluorometric sensor has excellent selectivity, reproducibility, and stability, providing a feasible method for not only the detection of CPS pesticides but also other analytes in the future.

Ultrasensitive and highly selective Co2+ detection based on the chiral optical activities of L-glutathione-modified gold nanoclusters

Developing highly sensitive and selective detection methods is crucial for environmental and healthcare monitoring. In this study, the chiral and fluorescent signals of L-glutathione-modified gold nanoclusters (L-GSH-Au NCs) were discovered to be responsive to Co2+, which displayed linear correlations with the concentration changes of Co2+. Notably, the chiral signal was more sensitive than the FL signal, whose limit of detection (LOD) was calculated to be 0.37 μM and 3.93 times lower than the LOD obtained with fluorescent signals. Moreover, the chiral signals exhibited unexpectedly high selectivity towards Co2+, effectively avoiding interference from other metal ions and biomolecules. Furthermore, the concentrations of Co2+ in various samples, such as Taihu water, tap water, bottled water, and animal serum, were accurately quantified using the chiral signals of L-GSH-Au NCs without complex pretreatment, with recoveries ranging between 95.64% and 103.22%. This study not only provides an innovative approach for Co2+ detection but also highlights the detection capabilities of chiral signals in complex environments.

Recent advances and trends in innovative biosensor-based devices for heavy metal ion detection in food

Low-cost, reliable, and efficient biosensors are crucial in detecting residual heavy metal ions (HMIs) in food products. At present, based on distance-induced localized surface plasmon resonance of noble metal nanoparticles, enzyme-mimetic reaction of nanozymes, and chelation reaction of metal chelators, the constructed optical sensors have attracted wide attention in HMIs detection. Besides, based on the enrichment and signal amplification strategy of nanomaterials on HMIs and the construction of electrochemical aptamer sensing platforms, the developed electrochemical biosensors have overcome the plague of low sensitivity, poor selectivity, and the inability of multiplexed detection in the optical strategy. Moreover, along with an in-depth discussion of these different types of biosensors, a detailed overview of the design and application of innovative devices based on these sensing principles was provided, including microfluidic systems, hydrogel-based platforms, and test strip technologies. Finally, the challenges that hinder commercial application have also been mentioned. Overall, this review aims to establish a theoretical foundation for developing accurate and reliable sensing technologies and devices for HMIs, thereby promoting the widespread application of biosensors in the detection of HMIs in food.

Multifunctional Nanocarrier for Synergistic Treatment of Alzheimer's Disease by Inhibiting β-Amyloid Aggregation and Scavenging Reactive Oxygen Species

The excessive depositions of β-amyloid (Aβ) and abnormal level of reactive oxygen species (ROS) are considered as the important pathogenic factors of Alzheimer's disease (AD). Strategies targeting only one of them have no obvious effects in clinic. In this study, a multifunctional nanocarrier CICe@M-K that crosses the blood-brain barrier (BBB) efficiently was developed for inhibiting Aβ aggregation and scavenging ROS synchronously. Antioxidant curcumin (Cur) and photosensitizer IR780 were loaded in mesoporous silica nanomaterials (MSNs). Their surfaces were grafted with cerium oxide nanoparticles (CeO2 NPs) and a short peptide K (CKLVFFAED). Living imaging showed that CICe@M-K was mainly distributed in the brain, liver, and kidneys, indicating CICe@M-K crossed BBB efficiently and accumulated in brain. After the irradiation of 808 nm laser, Cur was continuously released. Both of Cur and the peptide K can recognize and bind to Aβ through multiple interaction including π-π stacking interaction, hydrophobic interaction, and hydrogen bond, inhibiting Aβ aggregation. On the other hand, Cur and CeO2 NPs cooperate to relieve the oxidative stress in the brains by scavenging ROS. In vivo assays showed that the CICe@M-K could diminish Aβ depositions, alleviate oxidative stress, and improve cognitive ability of the APP/PS1 AD mouse model, which demonstrated that CICe@M-K is a potential agent for AD treatment.

Colorimetric detection of Hg2+ based on the enhanced oxidase-mimic activity of CuO/Au@Cu3(BTC)2 triggered by Hg2

It is imperative to develop a rapid detection method for Hg2+ due to its harm to human health and the ecological environment. In this research, CuO/Au@Cu3(BTC)2 was synthesized through reducing HAuCl4 by CuxO@Cu3(BTC)2, which was obtained by reducing Cu3(BTC)2 with hydrazine hydrate. The oxidase-mimic activity of CuO/Au@Cu3(BTC)2 can be enhanced by Hg2+ through forming a Au-Hg alloy. Therefore, a colorimetric method was designed for Hg2+ detection with a linear relationship in the 0.05-25 μM range and a limit of detection of 9.7 nM. This strategy exhibited a strong selectivity to Hg2+ and was applied in a real water sample with reliable recoveries. This work provides a possibility for the rapid detection of Hg2+.

Label-free fluorescence detection of mercury ions based on thymine-mercury-thymine structure and CRISPR-Cas12a

In this work, we developed a novel label-free fluorescent sensor for the highly sensitive detection of mercury ions (Hg2+) based on the coordination chemistry of thymine-Hg2+-thymine (T-Hg2+-T) structures and the properties of CRISPR-Cas12a systems. Most notably, two T-rich sequences (a blocker and an activator) were designed to form stable double-stranded structures in the presence of Hg2+ via the T-Hg2+-T base pairing. The formation of T-T mismatched double-stranded DNA between the blocker and the activator prevented the cleavage of G-rich sequences by Cas12a, allowing them to fold into G-quadruplex-thioflavin T complexes, resulting in significantly enhanced fluorescence. Under the optimized conditions, the developed sensor showed an excellent response for Hg2+ detection in the linear range of 0.05 to 200 nM with a detection limit of 23 pM. Moreover, this fluorescent sensor exhibited excellent selectivity and was successfully used for the detection of Hg2+ in real samples of Zhujiang river water and tangerine peel, demonstrating its potential in environmental monitoring and food safety applications.

A novel "on-off-on" electrochemiluminescence strategy based on RNA cleavage propelled signal amplification and resonance energy transfer for Pb2+ detection

BACKGROUND

Lead (Pb) is one of the most toxic heavy-metal pollutants. Additionally, lead ions (Pb2+) can accumulate in the human body through the food chain, causing irreversible damage through organ damage and system disorders. In the past few years, the detection of Pb2+ has mainly relied on instrumental methods such as atomic absorption spectroscopy (AAS) and inductively coupled plasma mass spectrometry (ICP-MS). Nonetheless, these techniques are complicated in terms of equipment and procedures, along with being time-intensive and expensive in terms of detection. These drawbacks have limited their wide application. Hence, there is a pressing need to develop detection techniques for Pb2+ that are not only cost-efficient but also highly sensitive and specific.

RESULTS

A novel "on-off-on" electrochemiluminescence (ECL) sensor for detecting Pb2+ was developed based on the resonance energy transfer (RET) effect between AuNPs and boron nitride quantum dots (BN QDs) and the recognition of Pb2+ by DNAzyme along with the cleavage reaction of the substrate chain. Poly(6-carboxyindole)/stannic sulfide (P6ICA/SnS2) nanocomposite was employed as a co-reaction accelerator to consequently facilitate the production of intermediate SO4•-. This effective enhancement of the reaction led to an improved ECL intensity of BN QDs and enabled the sensor platform to exhibit a higher original ECL response. Benefiting from the combination of the DNAzyme signal amplification strategy with the "on-off-on" design, the ECL sensor showed satisfactory selectivity, good stability, and high sensitivity. This ECL sensor exhibited a linear detection range (LDR) of 10-12-10-5 M and a limit of detection (LOD) of 2.6 × 10-13 M.

SIGNIFICANCE

In the present work, an "on-off-on" ECL sensor is constructed based on RET effect for ultrasensitive detection of Pb2+. P6ICA/SnS2 was investigated as the co-reaction accelerator in this sensor. Moreover, this ECL sensor exhibited excellent analytical capability for detecting Pb2+ in actual water samples, providing a method for detecting other heavy metal ions as well.

A Controlled Release Aptasensor Utilizing AIE-Active MOFs as High-Efficiency ECL Nanoprobe for the Sensitive Detection of Adenosine Triphosphate

Improving the sensitivity in electrochemiluminescence (ECL) detection systems necessitates the integration of robust ECL luminophores and efficient signal transduction. In this study, we report a novel ECL nanoprobe (Zr-MOF) that exhibits strong and stable emission by incorporating aggregation-induced emission ligands into Zr-based metal-organic frameworks (MOFs). Meanwhile, we designed a high-performance signal modulator through the implementation of a well-designed controlled release system with a self-on/off function. ZnS quantum dots (QDs) encapsulated within the cavities of aminated mesoporous silica nanoparticles (NH2-SiO2) serve as the ECL quenchers, while adenosine triphosphate (ATP) aptamers adsorbed on the surface of NH2-SiO2 through electrostatic interaction act as "gatekeepers." Based on the target-triggered ECL resonance energy transfer between Zr-MOF and ZnS QDs, we establish a coreactant-free ECL aptasensor for the sensitive detection of ATP, achieving an impressive low detection limit of 0.033 nM. This study not only demonstrates the successful combination of ECL with controlled release strategies but also opens new avenues for developing highly efficient MOFs-based ECL systems.

Ratiometric electrogenerated chemiluminescence sensing microRNA based on electrochemically controlled release of lucigenin from silica/chitosan/lucigenin nanoparticles

The dye-doped silica nanoparticles-based electrogenerated chemiluminescence (ECL) has been widely explored for analytical purposes due to its high sensitivity, simplicity and wide dynamic concentration range. However, only a few of dye molecules located at the near surface of nanoparticles can participate in the ECL reaction due to the poor conductivity of silica nano-matrix. In addition, the ECL signal is easy to be affected by environmental interference, which results in poor accuracy. Herein, a ratiometric ECL sensing method is established based on the electrochemically controlled release of lucigenin molecules from silica/chitosan/lucigenin composite nanoparticles (Lu/CS NPs) with the aid of sulfide ions. Firstly, H+ produced from the electrochemical oxidation of HS- ions can combine with SiO- and displace lucigenin from Lu/CS NPs. The released lucigenin molecules react with the reactive oxygen species (ROS) generated from the electroreduction of dissolved oxygen to produce the cathodic ECL signal. In addition, the excited elemental sulfur from the electrooxidation of HS- ions transfers its energy to lucigenin molecules and makes them be excited to produce energy-transfer anodic ECL signal. Based on these findings, a ratiometric ECL sensor is developed taking the anodic ECL intensity of lucigenin as a reference signal for the cathodic ECL of lucigenin. The proposed ratiometric ECL sensor has been successfully applied to the detection of let-7a with a wide linear range of 0.1-9.0 pM, a low detection limit of 28 fM, high selectivity and good reproducibility. Moreover, the developed approach was used to detect let-7a in human serum composite samples with good recoveries.

Target-Controlled Redox Reaction and Ru(II) Release of a Smart Metal-Organic Framework Nanomaterial for Highly Sensitive Ratiometric Homogeneous Electroanalysis of Cadmium(II)

In this work, a highly sensitive ratiometric homogeneous electroanalysis (HEA) strategy of cadmium(II) (Cd2+) was proposed via a Cd2+-controlled redox reaction and Ru(bpy)32+ (Ru(II)) release from a smart metal-organic framework (MOF) nanomaterial. For achieving this purpose, Ru(II) was entrapped ingeniously into the pores of an MOF material (UiO-66-NH2) and subsequently gated by the double-strand hybrids of a Cd2+-aptamer (Apt) and its complementary sequences (CP) to form a novel smart nanomaterial (denoted as Ru@UiO-66-NH2); meanwhile, Fe(III) was selected as an additional probe present in electrolyte to facilitate the Ru(II) redox reaction: Fe(III) + Ru(II) → Fe(II) + Ru(III). Owing to the strong binding effect of the Cd2+ target to the specific Apt, the Apt-CP hybridization at Ru@UiO-66-NH2 would be destroyed in the presence of Cd2+, and the related Apt was further induced away from the smart nanomaterial, leading to the opening of the gate and release of Ru(II). Meanwhile, the released Ru(II) was quickly oxidized chemically by Fe(III) to Ru(III). On the basis of the generated Ru(III) and consumed Fe(III), the ratio of the reduction currents between Ru(III) and Fe(III) exhibits an enhancement and it is dependent on the level of Cd2+; thus, a novel HEA strategy of Cd2+ was then designed. Under the optimal conditions, the HEA sensor shows a wide linearity ranging from 10.0 pM to 500.0 nM, and the achieved detection limit of Cd2+ is 3.3 pM. The as-designed ratiometric HEA strategy not only offers a unique idea to realize a simple and sensitive assay for Cd2+ but also possesses significant potential as an effective tool to be introduced for other target analysis just via altering the specific Apt.

Hg2+-triggered cascade strand displacement assisted CRISPR-Cas12a for Hg2+ quantitative detection using a portable glucose meter

CRISPR-Cas12a is a powerful and programmable tool that has revolutionized the field of biosensing. However, the construction of a CRISPR-Cas12a-mediated portable system for on-site and quantitative detection of mercury ion (Hg2+) has yet to be explored. By integrating a target-triggered cascade toehold-mediated strand displacement reaction (TSDR) and CRISPR-Cas12a, we herein construct a portable on-site biosensor for the quantitative, sensitive, and selective detection of Hg2+ with a glucose meter. The Hg2+ initiates two cascade TSDRs through the T-Hg2+-T interaction to produce multiple double-stranded DNAs that can activate Cas12a's trans-cleavage activity. The Cas12a cleaves the sucrase-modified DNA on the electrode, resulting in the liberation of sucrase into the solution. The freed sucrase can catalyze sucrose to generate glucose, which can be quantitatively monitored by a glucometer. The developed portable biosensor provides a dynamic range of 5 orders of magnitude with a detection limit of 40 fM. This biosensor also displays excellent selectivity and stability for detecting Hg2+. Moreover, environmental water samples are utilized to further verify the robustness and effectiveness of the developed biosensor, highlighting its potential application in environmental monitoring and food safety analysis.

Electrochemiluminescence Sensor with Controlled-Release Triggering Electrostatic Attraction Elimination Mechanism for Trenbolone Trace Detection

A controlled-release strategy can meet the needs of sensitive environmental monitoring for pollutants through a self-on/off mode. In this work, an electrochemiluminescence (ECL) biosensor with controlled-release triggering electrostatic attraction elimination and biomolecular stimulated response strategies was constructed to detect environmental steroid hormones sensitively. The blocked pores on the aminated mesoporous silica nanocontainers were opened by specific binding between the trenbolone (TB) antigen and the antibody. The released l-cysteine counteracted the negative charge on the MnO2 NF surface through the redox reaction between -SH and MnO2, making the electrostatic interaction between the MnO2 NFs and the Ru(dcbpy)32+ disappear. Ru(dcbpy)32+ released an ECL signal on the electrode, thus completing the controlled-release triggering electrostatic attraction elimination strategy. In addition, with the TB antibody as the target and the competition strategy between the TB antigen and the standard substance, the constructed controlled-release ECL biosensor was used to detect the TB standard substance. Moreover, MnO2 NFs as the substrate of the ECL biosensor increased the active specific surface area of the electrode, effectively catalyzing the production of OH• and O2•-, thus endowing the ECL biosensor with coreactant-catalytic enhancement characteristic and further improving its ECL performance. This sensitive signal response brought about a low limit of detection of 2.53 fg/mL for the constructed ECL biosensor, which contributed a feasible idea for efficient trace analysis of pollutants in the environment.

CRISPR/Cas12a-Powered EC/FL Dual-Mode Controlled-Release Homogeneous Biosensor for Ultrasensitive and Cross-Validated Detection of Messenger Ribonucleic Acid

Accurate detection of cancer-associated mRNAs is beneficial to early diagnosis and potential treatment of cancer. Herein, for the first time, we developed a novel CRISPR/Cas12a-powered electrochemical/fluorescent (EC/FL) dual-mode controlled-release homogeneous biosensor for mRNA detection. A functionalized ssDNA P2-capped Fe3O4-NH2 loaded with methylene blue (P2@MB-Fe3O4-NH2) was synthesized as the signal probe, while survivin mRNA was chosen as the target RNA. In the presence of the target mRNA, the nicking endonuclease-mediated rolling circle amplification (NEM-RCA) was triggered to produce significant amounts of ssDNA, activating the collateral activity of Cas12a toward the surrounding single-stranded DNA. Thus, the ssDNA P1 completely complementary to ssDNA P2 was cleaved, resulting in that the ssDNA P2 bio-gate on Fe3O4-NH2 could not be opened due to electrostatic interactions. As a result, there was no or only a little MB in the supernatant after magnetic separation, and the measured EC/FL signal was exceedingly weak. On the contrary, the ssDNA P2 bio-gate was opened, enabling MB to be released into the supernatant, and generating an obvious EC/FL signal. Benefiting from the accuracy of EC/FL dual-mode cross-verification, high amplification efficiency, high specificity of NEM-RCA and CRISPR/Cas12a, and high loading of mesoporous Fe3O4-NH2 on signal molecules, the strategy shows aM-level sensitivity and single-base mismatch specificity. More importantly, the practical applicability of this dual-mode strategy was confirmed by mRNA quantification in complex serum environments and tumor cell lysates, providing a new way for developing a powerful disease diagnosis tool.

Flexible carbon fiber cloth supports decorated with cerium metal- organic frameworks and multi-walled carbon nanotubes for simultaneous on-site detection of Cd2+ and Pb2+ in food and water samples

The widespread heavy metal pollution endangers human health; hence, accurate on-site detection and quantification of heavy metal content in the surroundings is a vital step in reversing the harmful effect. Herein, an electrochemical sensor based on flexible cerium metal-organic framework@multi-walled carbon nanotubes/carbon cloth (CeMOF@MWCNTs/CC) was constructed for simultaneous on-site detection of Cd²⁺ and Pb²⁺ in food and water samples. The rich carboxyl groups of MWCNTs provided abundant sites for the adsorption of Cd²⁺ and Pb²⁺, and the mutual conversion of Ce³⁺ and Ce⁴⁺ in CeMOF facilitated the reduction and reoxidation of metal ions. The prepared electrode showed excellent performance in the simultaneous measurement of Cd²⁺ and Pb²⁺, with detection limits of 2.2 ppb and 0.64 ppb, respectively. More importantly, the sensing platform has been successfully used to detect simultaneously Cd²⁺ and Pb²⁺ in grain and water samples, and the detection results were consistent with the standard methods, showing great potential in environmental monitoring and food safety.

An ultrasensitive split-type electrochemical immunosensor based on controlled-release strategy for detection of CA19-9

In this study, a novel split-type electrochemical immunosensor based on controlled release strategy was proposed for sensitive analysis and detection of tumor marker carbohydrate antigen 199 (CA19-9). Specifically, glucose (Glu) was encapsulated in carrier mesoporous silica (MSN) with encapsulation technology, and surface functionalized Zinc sulfide (ZnS) caps were used as "gatekeepers". The complex is formed by encapsulating Glu within MSN with ZnS (ZnS@MSN-Glu) as a signal amplifier labeled on the signal antibody (Ab₂). And the Ab₂ can detect the presence of antibodies. To reduce the interference of biological analysis, the immune recognition process of ZnS@MSN-Glu-Ab₂ bioconjugate and antigen was carried out in 96-well microplate, which did not interfere with the electrochemical analysis process. Therefore, the low sensitivity detection caused by biofouling of nanomaterials and immunoreaction on the testing platform is eliminated. Subsequently, the opening and timed release of mesopores were controlled by external stimuli, the disulfide bond cleavage by dithiothreitol (DTT), and glucose was effectively released. Then nickel cobalt layered double hydroxide (NiCo-LDH) were directly hydrothermally grown on carbon cloth (CC) electrodeposited with copper selenide (CuSe) nanosheets to construct three-dimensional (3D) cactus-like NiCo-LDH/CuSe/CC sensing platform. It can realize the catalytic oxidation of released glucose, triggering glucose-mediated signal amplification. The synergistic effect of the 3D cactus structure and active nanomaterials promotes electron conduction. Taking the detection of carbohydrate antigen CA19-9 as an example, the immunosensor shows a wide linear concentration range (0.001-100 U/mL) with the limit of detection of 0.0005 U/mL, realizing highly sensitive detection of CA19-9. This biosensing technique has considerable advantages and provides an innovative approach for trace detection of other biomarkers.

Target-activated multivalent sensing platform for improving the sensitivity and selectivity of Hg2+ detection

Sensitivity and selectivity are critical parameters to evaluate the performance of sensors. For trace detection, it remains a challenge to design a new sensor that achieves high sensitivity and selectivity simultaneously. Here, we present a target-activated dual Mg²⁺-dependent DNAzyme (MNAzyme) that served as a simple sensing model to explore the multivalency in improving the analytical sensitivity and selectivity for target detection. Mercury ion (Hg²⁺), a notorious toxic metal ion, was selected as a model target. In the presence of Hg²⁺, the thymine-rich regions of the hairpin probe and primer could hybridize to form a stable duplex via the thymine-Hg²⁺-thymine structure. Then, an intact enzyme sequence was exposed and two separate enzyme fragments were close to each other, generating a dual MNAzyme. Benefiting from the localized high-concentration of the enzyme strand, the dual MNAzyme showed a remarkable improvement in binding stability. The catalytic rate constant of the dual MNAzyme was theoretically 1.60 times higher than that of the monomeric counterpart, and the sensitivity and selectivity had 4.50 and 1.44-fold enhancement, respectively. When the dual MNAzyme was used for sensor applications, the limit of detection was determined to be 0.04 and 0.2 nM via UV-vis spectrophotometer and naked eye, respectively. Meanwhile, the method offered desirable selectivity toward Hg²⁺ against other metal ions. With the advantages of simple operation, high sensitivity, and desirable selectivity, the developed multivalent sensing platform could be easily expanded in the future for the on-site detection of other low-abundance analytes.

Homogeneous voltammetric sensing strategy for lead ions based on aptamer gated methylthionine chloride@UiO-66-NH2 framework as smart target-stimulated responsive nanomaterial

Herein an innovative electrochemical method is proposed for the determination of lead ions (Pb²⁺) based on a homogeneous voltammetric (HVC) sensing strategy using an aptamer gated methylthionine chloride@UiO-66-NH₂ framework as a smart target-stimulated responsive material. The proposed HVC sensor exhibits excellent sensing performance: ultralow detection limit (0.166 pM) and wide linearity (5.0 pM-500.0 nM), simultaneously, it avoids electrodeposition processes and it is simple to modify the electrode compared to previous electrochemical methods for Pb²⁺ detection. Thus our method shows great potential in the highly efficient detection of Pb²⁺ and other heavy metal ions by simply altering the related specific aptamer.

Dual fluorescent aptasensor for simultanous and quantitative detection of sulfadimethoxine and oxytetracycin residues in animal-derived foods tissues based on mesoporous silica

Herein, we developed a dual fluorescent aptasensor based on mesoporous silica to simultaneously detect sulfadimethoxine (SDM) and oxytetracycline (OTC) in animal-derived foods. We immobilized two types of aptamers modified with FAM and CY5 on the silica surface by base complementary pairing reaction with the cDNA modified with a carboxyl group and finally formed the aptasensor detection platform. Under optimal conditions, the detection range of the aptasensor for SDM and OTC was 3-150 ng/mL (R ² = 0.9831) and 5-220 ng/mL (R ² = 0.9884), respectively. The limits of detection for SDM and OTC were 2.2 and 1.23 ng/mL, respectively. The limits of quantification for SDM and OTC were 7.3 and 4.1 ng/mL, respectively. Additionally, the aptasensor was used to analyze spiked samples. The average recovery rates ranged from 91.75 to 114.65% for SDM and 89.66 to 108.94% for OTC, and all coefficients of variation were below 15%. Finally, the performance and practicability of our aptasensor were confirmed by HPLC, demonstrating good consistency. In summary, this study was the first to use the mesoporous silica-mediated fluorescence aptasensor for simultaneous detection of SDM and OTC, offering a new possibility to analyze other antibiotics, biotoxins, and biomolecules.

Recent Achievements in Electrochemical and Optical Nucleic Acids Based Detection of Metal Ions

Recently nucleic acids gained considerable attention as selective receptors of metal ions. This is because of the possibility of adjusting their sequences in new aptamers selection, as well as the convenience of elaborating new detection mechanisms. Such a flexibility allows for easy utilization of newly emerging nanomaterials for the development of detection devices. This, in turn, can significantly increase, e.g., analytical signal intensity, both optical and electrochemical, and the same can allow for obtaining exceptionally low detection limits and fast biosensor responses. All these properties, together with low power consumption, make nucleic acids biosensors perfect candidates as detection elements of fully automatic portable microfluidic devices. This review provides current progress in nucleic acids application in monitoring environmentally and clinically important metal ions in the electrochemical or optical manner. In addition, several examples of such biosensor applications in portable microfluidic devices are shown.

A ratiometric electrochemical strategy based on Fe (III) and Pt (IV) for immobilization-free detection of Escherichia coli

A new ratiometric electrochemical strategy for immobilization-free detection of Escherichia coli (E. coli) was constructed by using a capture DNA-polyaniline/copper ferrite nanoparticles/graphene oxide (cDNA-PANI/CuFe₂O₄/GO) composite as capture probes, which has a high specific surface area and good magnetic properties. Then trigger DNA/Au nanoparticles (tDNA/Au NPs) were used as signal amplification labels, and Pt (IV) and Fe (III) were chosen as the signal probes. In the presence of targets, the sandwich format among cDNA-PANI/CuFe₂O₄/GO, E. coli and auxiliary DNA (aDNA) was realized by using the aptamer recognition system. Then, the tDNA/Au binding could be anchored on the sandwich format due to the principle of base complementation between unpaired aDNA and tDNA. And the unbounded tDNA of tDNA/Au NPs could bind an amount of Pt (IV). After separation using a magnet, a handful of unbound Pt (IV) which remained in the supernatant reacted with a large number of Fe (III) ions, leading to a markedly increased I_Fe(III)/I_Pt(IV) value. Oppositely, the sandwich format could not appear in the absence of targets, and even the tDNA/Au could not be immobilized on it. So, the redox reaction between a large amount of Pt (IV) residue in the supernatant and Fe (III) was significantly successful, causing a low I_Fe(III)/I_Pt(IV) value. Under optimal conditions, we found that I_Fe(III)/I_Pt(IV) was linearly related to the logarithmic E. coli concentration with a low limit of detection (1.862 × 10³ cfu mL^-1). This devised ratiometric electrochemical method may develop into a powerful and effective means for the detection of E. coli in real samples, which may also be developed as a universal tool for another microorganism.

Electric Field-Induced Specific Preconcentration to Enhance DNA-Based Electrochemical Sensing of Hg2+ via the Synergy of Enrichment and Self-Cleaning

Efficient preconcentration is critical for sensitive and selective electrochemical detection of metal ions, but rapid specific enrichment with depressed absorption of interfering ions at the electrode is challenging. Here, we proposed an electric field-induced specific preconcentration to boost the analytical performance of DNA-based electrochemical sensors for Hg²⁺ detection. As for such preconcentration, a positive external electric field was first used to enrich Hg²⁺ at an electrode assembled with T-rich DNA, thus boosting T-Hg²⁺-T recognitions. The following applied inverse electric field strips the nonspecifically absorbed Hg²⁺ and other interfering ions, thus depressing matrix interferences via self-cleaning. Based on this principle, we designed a portable device to realize programmable control of electric fields; a T-Hg²⁺-T recognition-based electrochemical sensor was thus fabricated as a model platform to assess the feasibility of electric field-induced preconcentration. The experimental results revealed that such a strategy decreased the time of T-Hg²⁺-T-based recognition from 60 to 20 min and led to detection with better reproducibility by depressing the influence of free Hg²⁺ as well as interfering ions. This strategy offered Hg²⁺ detection limits of 0.01 pM─three-fold better than that without preconcentration─within 22 min. The proposed preconcentration strategy offers a new way to enhance the analytical performance of sensing at the solid-liquid interface.

Designing Triangular Silver Nanoplates with GSH/GSSG Surface Mixed States as Novel Nanoparticle-based Redox Mediators for Electrochemical Biosensing

Herein, a dual signal-quenched electrochemical (EC) biosensing strategy utilizing surface-engineered trisodium citrate (TSC)-glutathione (GSH)/oxidized glutathione (GSSG)-capped triangular silver nanoplates (Tri-Ag NPs_TSC-GSH/GSSG) as a novel nanoparticle-based redox mediator was explored for biomarker determination. In contrast with conventional redox mediators, Tri-Ag NPs_TSC-GSH/GSSG provided more admirable EC performance along with a lower oxidation potential (∼0.14 V). Taking advantage of the split-type mode, the immune response in a 96-well microplate was independent from EC detection, which could effectively eliminate the biological interference and thereby greatly enhance the sensitivity. As for the surface engineering process of Tri-Ag NPs, it was composed of partial GSH replacement and the formation of the GSH/GSSG surface mixed state. Primarily, the signal response of Ag NPs_TSC-GSH decreased due to the hindrance of GSH on electron transfer. Moreover, varying proportions of GSH/GSSG could further impede the oxidation process of Tri-Ag NPs_TSC-GSH/GSSG and eventually realize efficient dual signal quenching of this system. Notably, the ZIF-67@MIL-88B-GO_x nanocomposite as the label was applied for a cascade reaction system with GSH peroxidase-like activities to form the optimal GSH/GSSG proportion, causing sensitive changes in signal response with a range of different antigen concentrations. On this basis, the fabricated biosensor provided measurable outputs of aflatoxin B1 concentrations in a linear range of 0.0005-50 ng/mL with a low detection limit of 0.61 pg/mL (S/N = 3). All of the results indicated that the novel biosensor could be a promising analytical tool for future biomarker detection.

Application of Nanomaterial Modified Aptamer-Based Electrochemical Sensor in Detection of Heavy Metal Ions

Heavy metal pollution resulting from significant heavy metal waste discharge is increasingly serious. Traditional methods for the detection of heavy metal ions have high requirements on external conditions, so developing a sensitive, simple, and reproducible detection method is becoming an urgent need. The aptamer, as a new kind of artificial probe, has received more attention in recent years for its high sensitivity, easy acquisition, wide target range, and wide use in the detection of various harmful substances. The detection platform that an aptamer-based electrochemical biosensor (E-apt sensor) provides is a new approach for the detection of heavy metal ions. Nanomaterials are particularly important in the construction of E-apt sensors, as they can be used as aptamer carriers or sensitizers to stimulate or inhibit electrochemical signals, thus significantly improving the detection sensitivity. This review summarizes the application of different types of nanomaterials in E-apt sensors. The construction methods and research progress of the E-apt sensor based on different working principles are systematically introduced. Moreover, the advantages and challenges of the E-apt sensor in heavy metal ion detection are summarized.

Tetrahedral DNA-directed core-satellite assembly as SERS sensor for mercury ions at the single-particle level

To monitor the deteriorating mercury emissions, it is imperative to propose methods for detecting mercury ions (Hg²⁺) with sensitivity and selectivity. The SERS spectral-resolved single-particle detection approach can be carried out using dark-field optical microscopy (DFM) combined with Raman spectroscopy. Herein, we have designed a novel yet convenient single-particle detection assay for quantifying Hg²⁺ using DFM-correlated Raman spectroscopy. In the assay, a tetrahedral DNA-directed core-satellite nanostructure is used as the SERS probe. Especially, one edge of the tetrahedron is made up of a single-stranded DNA containing a Hg²⁺ aptamer, which reconfigures upon the specific recognition of Hg²⁺. As a result, the interparticle distance reduces from 4.5 to 1.2 nm, thus generating Raman signal enhancement. As a proof of concept, Hg²⁺ was detected in a linear range from 1 to 100 nM based on the variation in SERS intensity. Furthermore, the experimental results were supported by the finite difference time domain (FDTD) calculations. Owing to its high sensitivity and selectivity, this method was further employed to detect Hg²⁺ in practical tap water and lake water samples, revealing that the single-particle detection strategy holds great promise for Hg²⁺ analysis in real environment analysis.

Target-Responsive Smart Nanomaterials via a Au-S Binding Encapsulation Strategy for Electrochemical/Colorimetric Dual-Mode Paper-Based Analytical Devices

Target-responsive nanomaterials attract growing interest in the application of drug delivery, bioimaging, and sensing due to the responsive releasing of guest molecules by the smart molecule gate. However, it remains a challenge to develop smart nanomaterials with simple assembly and low nonspecific leakage starting from encapsulation strategies, especially in the sensing field. Herein, Au nanoclusters (Au NCs) were first grown on porous carbon derived from ZIF-8 (PCZIF) to be employed as nanocarriers. By employing the Au NCs as linkers and aptamer (Apta) double-strand hybrids (target Apta and SH-complementary DNA) as capping units, we reported the novel target-responsive nanomaterials of Apta/Au NCs-PCZIF/hemin through Au-S binding encapsulation for sensing assays. The Au-S binding encapsulation strategy simplified the packaging procedure and reduced non-target responsive leakage. As a proof, ochratoxin A (OTA) as a model target participates in the double-strand hybrid competitive displacement reaction and triggered Apta conformation switches from a coil to a G-quadruplex structure accompanied by the dissociation of the gatekeeper. Simultaneously, the released hemin can initiate a self-assembly to form G-quadruplex/hemin DNAzyme. Interestingly, owing to DNAzyme providing electron transfer mediators and peroxidase-like activity, we proposed an electrochemical/colorimetric dual-mode paper-based analytical device (PAD) that provided self-verification to enhance reliability and accuracy, benefiting from independent signal conversion and transmission mechanism. As a consequence, the proposed dual-mode PAD could achieve sensitive electrochemical detection and visual prediction of OTA in the range of 1 pg/mL to 500 ng/mL and 50 pg/mL to 500 ng/mL, respectively. The electrochemical detection limit for OTA was as low as 0.347 pg/mL (S/N = 3). We believe that this work provides point-of-care testing (POCT) tools for a broad spectrum of applications.

Ultrasensitive electrochemical sensor for mercury ion detection based on molybdenum selenide and Au nanoparticles via thymine-Hg2+-thymine coordination

An ultrasensitive and specific-selection electrochemical sensor was constructed for Hg²⁺ detection based on Au nanoparticles and molybdenum selenide (Au NPs@MoSe₂) as well as the thymine-Hg²⁺-thymine (T-Hg²⁺-T) coordination. Herein, Au NPs@MoSe₂ not only could improve the sensitivity due to the large surface area and good electrical conductivity but also offered more sites to immobilize thiol-labeled T-rich hairpin DNA probes (P-1), which has a specific recognition for Hg²⁺ and methylene blue-labeled T-rich DNA probes (MB-P). When Hg²⁺ and MB-P exist, P-1 and MB-P can form a stable T-Hg²⁺-T complex. Then, methylene blue can be close to the electrode and detectable via differential pulse voltammetry (DPV). Benefiting from the specific recognition of T-Hg²⁺-T and the merits of Au NPs and MoSe₂, the fabricated biosensor presented an ultrasensitive and highly selective performance. The DPV responses had a positive linear relationship with Hg²⁺ concentrations over ten orders of magnitude from 1.0 × 10^-16 to 1.0 × 10^-7 mol L^-1. The detection limit was down to 1.1 × 10^-17 mol L^-1. Moreover, the developed sensor exhibited a promising application for trace Hg²⁺determination in water samples.

Plasmonic Gold Nanoparticles Stain Hydrogels for the Portable and High-Throughput Monitoring of Mercury Ions

The hybrid of l-cysteine and agarose can reduce HAuCl₄ and support the rapid growth of plasmonic gold nanoparticles (Au NPs) in the hydrogel phase. The l-cysteine-doped agarose hydrogel (C-AGH) not only offers the substrate the capacity to reduce Au(III) ions but also stabilizes and precisely modulates the in situ grown Au NPs with high repeatability, easy operation, and anti-interference performance. Herein, before the incubation of HAuCl₄, the improved hydrogel is preincubated in the aqueous solution containing mercury ions, and the cysteine can specifically conjugate with mercury via the thiol groups. Subsequently, the responsive allochroic bands from dark blue to red can be identified in the solid hydrogel after the incubation of HAuCl₄, which is attributed to the formation of regulated Au-Hg nanoamalgams. As a proof-of-concept, toxic Hg²⁺ ions are exploited as targets for constructing novel sensing assays based on the improved C-AGH protocol. Based on naked-eye recognition, Hg²⁺ could be rapidly and simply measured. Additionally, the high-throughput and trace analysis with a low limit of detection (3.7 nM) is performed using a microplate reader. On the basis of the filtering technique and remodeling of hydrogels, C-AGH working as the filtering membrane can even achieve the integration of enrichment and measurement with enhanced sensitivity. Significantly, the strategy of using an allochroic hydrogel with the staining of Au NPs can promote the rapid and primary assessment of water quality in environmental analysis.

Innovative ratiometric optical strategy: Nonconjugated polymer dots based fluorescence-scattering dual signal output for sensing mercury ions

A new ratiometric platform was developed for sensing Hg²⁺, which combined fluorescence and scattering simultaneously. This ratiometric strategy reflected superiorities over conventional methods, since the two independent signals at irrelevant categories meet the requirements of sufficient wavelength separation, stimulation under one excitation, and collection on single instrument. Herein, nonconjugated polymer dots (N-PDs) were served as the recognition unit for Hg²⁺ with turn-off fluorescence and turn-on scattering. Additionally, two signal collection tactics were proposed to achieve fluorescence and scattering in a window: one was to record down-conversion fluorescence and second-order scattering spectra (FL@SOS), and the other was to gather the fluorescence excited by second-order diffraction light and first-order scattering (SODL-FL@FOS). This ratiometric sensor exhibited outstanding performance toward Hg²⁺ in the range of 0.1-50 μM with the detection limit of 27 nM. By contrast, the present proposal provided a more ingenious and scalable way to construct ratiometric sensor than traditional approach.

Electrochemistry/Photoelectrochemistry-Based Immunosensing and Aptasensing of Carcinoembryonic Antigen

Recently, electrochemistry- and photoelectrochemistry-based biosensors have been regarded as powerful tools for trace monitoring of carcinoembryonic antigen (CEA) due to the fact of their intrinsic advantages (e.g., high sensitivity, excellent selectivity, small background, and low cost), which play an important role in early cancer screening and diagnosis and benefit people's increasing demands for medical and health services. Thus, this mini-review will introduce the current trends in electrochemical and photoelectrochemical biosensors for CEA assay and classify them into two main categories according to the interactions between target and biorecognition elements: immunosensors and aptasensors. Some recent illustrative examples are summarized for interested readers, accompanied by simple descriptions of the related signaling strategies, advanced materials, and detection modes. Finally, the development prospects and challenges of future electrochemical and photoelectrochemical biosensors are considered.

X-ray photoemission studies of the interaction of metals and metal ions with DNA

X-ray Photoelectron Spectroscopy (XPS) has been used to study the interactions of heavy metal ions with DNA with some success. Surface sensitivity and selectivity of XPS are advantageous for identifying and characterizing the chemical and elemental structure of the DNA to metal interaction. This review summarizes the status of what amounts to a large part of the photoemission investigations of biomolecule interactions with metals and offers insight into the mechanism for heavy metal-bio interface interactions. Specifically, it is seen that metal interaction with DNA results in conformational changes in the DNA structure.

Ultrasensitive colorimetric strategy for Hg2+ detection based on T-Hg2+-T configuration and target recycling amplification

A novelty aptasensor for ultrasensitive detection of Hg²⁺ is developed, exploiting the combination of plasmonic properties of gold nanoparticles (AuNPs) and exonuclease III (Exo III)-assisted target recycling for signal amplification. In the presence of Hg²⁺, a DNA duplex can be formed due to the strong coordination of Hg²⁺ and T bases of single-stranded DNA (ssDNA) probe. Exo III digests the DNA duplex from the 3' to 5' direction, resulting in the releasing of Hg²⁺. Then, the released Hg²⁺ binds with another ssDNA probe through T-Hg²⁺-T coordination. After Exo III-assisted Hg²⁺ cycles, numerous ssDNA probes are exhausted, which promotes poly(diallyldimethylammonium chloride) (PDDA)-induced AuNP aggregation, leading to an obvious color change and aggregation-induced plasmon red shift of AuNPs (from 520 to 610 nm). Therefore, this biosensor is ultrasensitive, which is applicable to the detection of trace level of Hg²⁺ with a linear range from 5 pM to 0.6 nM and an ultralow detection limit of 0.2 pM. Furthermore, it enables visual detection of Hg²⁺ as low as 50 pM by the naked eye. More importantly, the assay can be applied to the reliable determination of spiked Hg²⁺ in sea water samples with good recovery.

Programming a "Crab Claw"-like DNA Nanomachine as a Super Signal Amplifier for Ultrasensitive Electrochemical Assay of Hg2

Herein, with skillfully engaging stable T-Hg²⁺-T bonding, a "Crab Claw"-like DNA nanomachine with concise and highly efficient assembly and enhanced recognition/conversion efficiency was engineered as a super signal amplifier, which was united with Pd@Cu@Pt multimetallic mesoporous nanomaterials (Pd@Cu@Pt MMNs) for ultrasensitive electrochemical assay of mercury ions (Hg²⁺). Specifically, the formed "Crab Claw"-like DNA nanomachine could simultaneously trigger four same cascade DNAzyme cleavage reactions with the help of Mg²⁺ DNAzyme for markedly converting target Hg²⁺ to enormous DNA segments labeled with ferrocene (Fc), improving the detection sensitivity. Subsequently, the prepared Pd@Cu@Pt MMNs could not only show commendable electrochemical catalysis to Fc but also act as an excellent immobilization matrix for capturing and accumulating abundant Fc around them to further strengthen the electrochemical signal. As a result, the well-designed electrochemical sensor could achieve a low limit of detection of 3.58 fM in the range from 10 fM to 100 nM for Hg²⁺detection. This strategy offers a simple and rapid avenue to detect heavy metal ions and shows promising application potential for environmental pollutant monitoring.

Ultrasensitive and turn-on homogeneous Hg2+ sensing based on a target-triggered isothermal cycling reaction and dsDNA-templated copper nanoparticles

In this work, an ultrasensitive and turn-on sensor for homogeneous Hg2+ detection has been constructed based on a target-triggered isothermal cycling reaction and rapid label-free signal output with dsDNA-templated copper nanoparticles (CuNPs). As the key component of the sensor, a hairpin DNA without any labels was designed to contain different functional sequence segments and to resist digestion by exonuclease due to the protruding 3'-terminus. In the presence of Hg2+, the formation of a T-Hg2+-T structure turned the protruding 3'-terminus of the hairpin DNA to a blunt end that could be efficiently digested by Exo III, accompanied by Hg2+ release, followed by another digestion cycle. Hence, the Hg2+-triggered isothermal cycling reaction accumulated numerous dsDNA templates that facilitated fluorescent CuNP generation and finally output an amplified signal used to identify the target. This protocol is capable of Hg2+ sensing in a concentration range of 5 orders of magnitude with a detection limit down to 3.9 pM. The as-constructed sensor also revealed high selectivity, as well as satisfactory results in recovery experiments of Hg2+ detection in real water samples.

A photocurrent-polarity-switching biosensor for highly selective assay of mucin 1 based on target-induced hemin transfer from ZrO2 hollow spheres to G-quadruplex nanowires

Herein, a photocurrent polarity switching platform for highly selective assay of mucin 1 (MUC1) was developed based on target-induced hemin transfer from ZrO₂ hollow spheres (ZrO₂ HSs) to G-quadruplex nanowires (G wires). In this system, SiO₂ spheres were used as templates to synthesize the uniform and mesoporous ZrO₂ HSs. As nanocontainers, ZrO₂ HSs could load hemin in its cavity via pores. Then, the aptamers of MUC1, as bio-gates, blocked the pores of ZrO₂ HSs based on the specific binding of Zr⁴⁺ and the phosphate groups of aptamer. In the presence of MUC1, the aptamer could specifically recognize and bind with MUC1, and then leave away from the surface of ZrO₂ HSs, which resulted in the opening of the bio-gates and releasing of hemin. Assisted with the G wires formed on the Au NPs/In₂S₃/ITO, the released hemin was captured on the electrode through the formation of hemin/G-quadruplex structure, leading to the switch of the photocurrent polarity of the electrode from anodic photocurrent to cathodic photocurrent. The proposed photoelectrochemical biosensor showed outstanding performance for MUC1 assay with high selectivity, wide linear response range (1 fg mL^-1 -10 ng mL^-1) and lower detection limit (0.48 fg mL^-1). And the strategy could be easily extended to a triple-mode detection of MUC1 because the hemin/G-quadruplex structure was widely used in electrochemical and colorimetric methods as a hydrogen peroxide mimetic enzyme, which might provide wide applications in biological or clinical studies.

Dual-mode aptasensor for simultaneous detection of multiple food-borne pathogenic bacteria based on colorimetry and microfluidic chip using stir bar sorptive extraction

A dual-mode aptasensor using colorimetry and microfluidic chip (MC) together with stir bar sorptive extraction (SBSE) has been developed for firstly qualifying samples contaminated with Vibrio parahaemolyticus (V.P) and Salmonella typhimurium (S.T), then precisely determine both of them in positive samples. For this purpose, the aptamer-streptavidin encoded probes (Apt-SAEs) corresponding to different bacteria were prepared in advance. Then, a stir bar modified with 4-mercaptophenylboronic acid (MPBA) was made to extract bacteria together with Apt-SAE probes. The binding event of aptamer and target triggered the formation of two sandwich structures containing Apt-SAE, V.P or S.T. The concentration of bacteria could be enriched by 1000 times within 15 min to avoid long-time enrichment process. Finally, the stir bar was immersed in the 3,3',5,5'-Tetramethylbenzidine (TMB)-H₂O₂ solution for color development. The color could be observed by naked eyes to judge whether the analytes were present. The colorless samples were judged to be negative. For the positive samples, the adsorbed encoded probes corresponding to different bacteria would be eluted from the stir bar and rapidly analyzed by the MC. Under the optimized conditions, 100 CFU/mL of V.P or S.T or both of them could be observed by colorimetry and 35 CFU/mL of them could be detected (S/N = 3) by the MC. The assay has significant application value for on-site screening and multiple detection of food-borne pathogenic bacteria.

Electrochemical detection of heavy metal ions in water

Heavy metal ions are one of the main sources of water pollution. Most heavy metal ions are carcinogens that pose a threat to both ecological balance and human health. With the increasing demand for heavy metal detection, electrochemical detection is favorable due to its high sensitivity and efficiency. Here, after discussing the pollution sources and toxicities of Hg(ii), Cd(ii), As(iii), Pb(ii), UO₂(ii), Tl(i), Cr(vi), Ag(i), and Cu(ii), we review a variety of recent electrochemical methods for detecting heavy metal ions. Compared with traditional methods, electrochemical methods are portable, fast, and cost-effective, and they can be adapted to various on-site inspection sites. Our review shows that the electrochemical detection of heavy metal ions is a very promising strategy that has attracted widespread attention and can be applied in agriculture, life science, clinical diagnosis, and analysis.

Split-Type Electrochemical Immunoassay System Triggering Ascorbic Acid-Mediated Signal Magnification Based on a Controlled-Release Strategy

This research put forward a novel split-type electrochemical (EC) immunosensor which integrated the controlled-release strategy with EC detection for application in the field of biosensing. Concretely, ascorbic acid (AA) was packaged in a cadmium sulfide (CdS)-capped spherical mesoporous bioactive glass (SBG) nanocarrier (SBG_CdS) on account of encapsulation technology. To reduce the complexity of the bioanalysis, the detection antibody-labeled SBG_CdS-AA bioconjugate was applied in a 96-well microplate for the immunoreaction process, which is independent of the EC determination procedure. Thus, the immune interference and steric hindrance caused by the accumulation of nanomaterials on the electrode could be minimized. Subsequently, AA was released efficiently via the destruction effect of dithiothreitol on the disulfide bond. In addition, for the as-prepared FcAI/l-Cys/gold nanoparticles (GNPs)/porous BiVO₄ (p-BVO)/ITO EC sensing platform in the detection solution, the synergetic catalysis of Fc and GNPs/p-BVO toward the oxidation of the released AA could be realized, which triggered AA-mediated significant signal magnification throughout this study. In particular, p-BVO with an ordered nanoarray structure could accelerate the electron transfer to assist in sensitivity improvement of this system. This novel biosensor was capable of assaying the neuron-specific enolase (NSE) biomarker sensitively, from which a linear range of 0.001-100 ng/mL was derived along with a low detection limit of 1.08 pg/mL. An innovative way could be paved in the bioanalysis of NSE and other biomarkers.

Thymine-Functionalized Gold Nanoparticles (Au NPs) for a Highly Sensitive Fiber-Optic Surface Plasmon Resonance Mercury Ion Nanosensor

Mercury ion (Hg²⁺) is considered to be one of the most toxic heavy metal ions. Once the content of Hg²⁺ exceeds the quality standard in drinking water, the living environment and health of human beings will be threatened and destroyed. Therefore, the establishment of simple and efficient methods for Hg²⁺ ion detection has important practical significance. In this paper, we present a highly sensitive and selective fiber-optic surface plasmon resonance (SPR) Hg²⁺ ion chemical nanosensor by designing thymine (T)-modified gold nanoparticles (Au NPs/T) as the signal amplification tags. Thymine-1-acetic acid (T-COOH) was covalently coupled to the surface of 2-aminoethanethiol (AET)-modified Au NPs and Au film by 1-ethyl-3-(3-dimethylaminopropyl)carbodiimide hydrochloride/N-Hydroxysuccinimide (EDC/NHS) activation effect, respectively. In the presence of Hg²⁺ ions, the immobilized thymine combines specifically with Hg²⁺ ions, and forms an Au/thymine-Hg²⁺-thymine/Au (Au/T-Hg²⁺-T/Au) complex structure, leading to a shift in SPR wavelength due to the strong electromagnetic couple between Au NPs and Au film. Under optimal conditions, the proposed sensor was found to be highly sensitive to Hg²⁺ in the range of 80 nM–20 µM and the limit of detection (LOD) for Hg²⁺ was as low as 9.98 nM. This fiber-optic SPR sensor afforded excellent selectivity for Hg²⁺ ions against other heavy metal ions such as Fe³⁺, Cu²⁺, Ni²⁺, Ba²⁺, K⁺, Na⁺, Pb²⁺, Co²⁺, and Zn²⁺. In addition, the proposed sensor was successfully applied to Hg²⁺ assay in real environmental samples with excellent recovery. Accordingly, considering its simple advantages, this novel strategy provides a potential platform for on-site determination of Hg²⁺ ions by SPR sensor.