Advances in Sample Extraction

Nanoleaf-derived carbon materials as a sensitivity coating for solid‑phase microextraction of polycyclic aromatic hydrocarbons

Metal-organic framework-derived carbon materials have shown extensive application in the sensitive extraction of polycyclic aromatic hydrocarbons (PAHs), but more active sites for its adsorption were still a tireless pursuit. In this study, ZIF-nanoleaf-derived carbon (NLCs) was synthesized and developed as a solid-phase microextraction (SPME) fiber (NLCs-F). The extraction performance was compared with ZIF-dodecahedron-derived carbon (DHCs) coated fiber (DHCs-F), which was prepared by only changing the ratio of the reactants. The unique morphology of NLCs provided abundant adsorption active sites for the selected PAHs, while the large average aperture facilitated selective extraction of high molecular weight analytes. Additionally, the high carbon content enhanced the strong enrichment capability for hydrophobic PAHs. Hence, the prepared NLCs-F coupled with GC-MS showed a good correlation coefficient (0.9975) in a wide linear range, low limits of detection (0.3-1.8 ng L-1), satisfactory repeatability, and reproducibility, which made it apply in the enrichment of PAHs in actual tea and coffee samples.

Magnetic graphene oxide carbon dot nanocomposites as an efficient quantification tool against parabens in water and cosmetic samples

A new method is developed for the simultaneous detection and extraction of parabens, including methyl paraben (MP), ethyl paraben (EP), propyl paraben (PP), and butyl paraben (BP), based on magnetic graphene oxide carbon dot nanocomposites (Fe3O4@GO@CD). Fe3O4@GO@CD has been synthesized using one pot hydrothermal method by intercalating iron oxide and carbon dots between the layers of graphene oxide. Fe3O4@GO@CD was applied as the magnetic solid phase sorbent for the simultaneous extraction and detection of parabens from water (tap and river water) and cosmetic samples (hair serum and sunscreen cream). MP was measured at concentration of 0.25-0.26 ng/mL in hair serum, while PP at 0.32-0.33 ng/mL in sunscreen cream. Notably, good recoveries (88.74-98.03%; RSD = 2.31-6.88%) for river and tap water with detection limit of 0.039-0.046 ng/mL were attained. The method has good cyclability up to 16 cycles and was highly repeatable. All these findings suggest that the Fe3O4@GO@CD would be potential sorbent for the analysis of parabens.

A magnetic porous carbon material derived from an MIL-101(Fe) complex for efficient magnetic solid phase extraction of fluoroquinolone antibiotics

Extraction and determination of trace hazardous components from complex matrices continue to attract public attention. In this work, magnetic porous carbon (MPC) was prepared for efficient magnetic solid phase extraction (MSPE) of fluoroquinolone (FQ) antibiotics in food and water samples. To prepare the MPC, an Fe-based metal-organic framework (MIL-101(Fe)) was grown on a network of graphene oxide and multi-walled carbon nanotubes through a hydrothermal method, and then a carbonization process under a nitrogen atmosphere was carried out to obtain the MPC with high specific surface area and good magnetism. Four target FQs including ciprofloxacin (CIP), enrofloxacin (ENO), lomefloxacin (LOM) and ofloxacin (OFX) were enriched using the as-prepared MPC and determined by coupled high-performance liquid chromatography. Under the optimal conditions, the established MSPE-HPLC-UV detection method exhibited a linear range of 0.5-800 μg L-1 and detection limits of 0.11-0.18 μg L-1 with relative standard deviations (RSDs) of 0.5-4.8%. When applied in the determination of the above four FQs in real samples such as lake water, milk and pork, good recoveries between 85.2 and 103.7% were obtained, and the RSDs were less than 4.8%. This work indicates that the MPC material can be a good adsorption material and has good application prospects in antibiotics enrichment and/or removal from complex samples.

Rapid microwave synthesis of MOF microrods: Dispersive SPE coupled with UHPLC-MS/MS to determine fluoroquinolones in honey

A novel sorbent Cu-S metal-organic framework (MOF) microrods was prepared for dispersive solid-phase extraction via microwave synthesis and used to determine 12 fluoroquinolones (FQs) in honey samples employing ultrahigh-performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS). The best extraction efficiency was achieved by optimizing sample pH, sorbent quantity, eluent type/volume, and extraction and elution time. The proposed MOF exhibits advantages such as rapid synthesis time (20 min) and outstanding adsorption ability toward zwitterionic FQs. These advantages can be attributed to multiple interactions, including hydrogen bonding, π-π interaction, and hydrophobic interaction. The limits of detection of analytes were 0.005-0.045 ng g^-1. Acceptable recoveries (79.3%-95.6%) were obtained under the optimal conditions. Precision (relative standard deviation, RSD) was <9.2%. These results demonstrate the utility of our sample preparation method and the high capacity of Cu-S MOF microrods for rapid and selective extraction of FQs from honey samples.

A novel multiwalled carbon nanotube-cyclodextrin nanocomposite for solid-phase microextraction-gas chromatography-mass spectrometry determination of polycyclic aromatic hydrocarbons in snow samples

Novel solid-phase microextraction coatings based on the use of multiwalled carbon nanotube-cyclodextrin (MWCNT-CD) nanocomposites were developed for the determination of 16-priority polycyclic aromatic hydrocarbons at ultratrace levels in snow samples. The performance of both β- and γ-CD was tested to increase the detection capabilities towards the heaviest and most lipophilic compounds, i.e., five- and six-ring PAHs. To facilitate the interactions of MWCNTs with CDs, an oxidation procedure using both HNO₃ and H₂O₂ was applied, obtaining superior results using MWCNTs-H₂O₂-γ-CD fiber. Detection and quantitation limits below 0.7 and 2.3 ng/L, RSD lower than 21%, and recoveries of 88(± 2)-119.8(± 0.4)% proved the reliability of the developed method for the determination of PAHs at ultratrace levels. The complexation capability of the γ-CD was also demonstrated in solution by NMR and fluorescence spectroscopy studies and at solid state by XRD analysis. Finally, snow samples collected in the ski area of Dolomiti di Brenta were analyzed, showing a different distribution of the 16 priority PAHs, being naphthalene, phenanthrene, fluoranthene, and pyrene the only compounds detected in all the analyzed samples.

Development and application of lipidomics for food research

Lipidomics is an emerging and promising omics derived from metabolomics to comprehensively analyze all of lipid molecules in biological matrices. The purpose of this chapter is to introduce the development and application of lipidomics for food research. First, three aspects of sample preparation are introduced: food sampling, lipid extraction, and transportation and storage. Second, five types of instruments for data acquisition are summarized: direct infusion-mass spectrometry (MS), chromatographic separation-MS, ion mobility-MS, MS imaging, and nuclear magnetic resonance spectroscopy. Third, data acquisition and analysis software are described for the lipidomics software development. Fourth, the application of lipidomics for food research is discussed such as food origin and adulteration analysis, food processing research, food preservation research, and food nutrition and health research. All the contents suggest that lipidomics is a powerful tool for food research based on its ability of lipid component profile analysis.

Advances in solid-phase extraction techniques: Role of nanosorbents for the enrichment of antibiotics for analytical quantification

Antibiotics are life-saving medications for treating bacterial infections; however it has been discovered that resistance developed by bacteria against these incredible agents is the primary contributing factor to rising global mortality rates. The fundamental cause of the emergence of antibiotic resistance in bacteria is the presence of antibiotic residues in various environmental matrices. Although antibiotics are present in diluted form in environmental matrices like water, consistent exposure of bacteria to these minute levels is enough for the resistance to develop. So, identifying these tiny concentrations of numerous antibiotics in various and complicated matrices will be a crucial step in controlling their disposal in those matrices. Solid phase extraction, a popular and customizable extraction technology, was developed according to the aspirations of the researchers. It is a unique alternative technique that could be implemented either alone or in combination with other approaches at different stages because of the multitude of sorbent varieties and techniques. Initially, sorbents are utilized for extraction in their natural state. The basic sorbent has been modified over time with nanoparticles and multilayer sorbents, which have indeed helped to accomplish the desired extraction efficiencies. Among the current traditional extraction techniques such as liquid-liquid extraction, protein precipitation, and salting out techniques, solid-phase extractions (SPE) with nanosorbents are most productive because, they can be automated, selective, and can be integrated with other extraction techniques. This review aims to provide a broad overview of advancements and developments in sorbents with a specific emphasis on the applications of SPE techniques used for antibiotic detection and quantification in various matrices in the last two decades.

Partitioning-Induced Isolation of Analyte and Analysis via Multiscaled Aqueous Two-Phase System

Most fluorescence-based bioanalytical applications need labeling of analytes. Conventional labeling requires washing to remove the excess fluorescent labels and reduce the noise signals. These pretreatments are labor intensive and need specialized equipment, hindering portable applications in resource-limited areas. Herein, we use the aqueous two-phase system (ATPS) to realize the partitioning-induced isolation of labeled analytes from background signals without extra processing steps. ATPS is formed by mixing two polymers at sufficiently high concentrations. ATPS-based isolation is driven by intrinsic affinity differences between analytes and excess labels. To demonstrate the partitioning-induced isolation and analysis, fluorescein isothiocyanate (FITC) is selected as the interfering fluorophore, and a monoclonal antibody (IgG) is used as the analyte. To optimize ATPS compositions, different molecular weights and mass fractions of polyethylene glycol (PEG) and dextran and different phosphate-buffered saline (PBS) concentrations are investigated. Various operational scales of our approach are demonstrated, suggesting its compatibility with various bioanalytical applications. In centimeter-scale ATPS, the optimized distribution ratios of IgG and FITC are 91.682 and 0.998 using PEG 6000 Da and dextran 10,000 Da in 10 mM PBS. In millimeter-scale ATPS, the analyte is enriched to 6.067 fold using 15 wt % PEG 35,000 Da and 5 wt % dextran 500,000 Da in 10 mM PBS. In microscale ATPS, analyte dilutions are isolated into picoliter droplets, and the measured fluorescence intensities linearly correlated with the analyte concentrations (R² = 0.982).

Nickel hydroxide nanoflower-based dispersive solid-phase extraction of copper from water matrix

In this work, a dispersive solid-phase extraction method based on Ni(OH)₂ nanoflowers (Ni(OH)₂-NFs-DSPE) was developed to separate and preconcentrate copper ions from tap water samples for determination by flame atomic absorption spectrometry (FAAS). Ni(OH)₂-NFs was synthesized using a homogeneous precipitation technique and used as sorbent for copper preconcentration. X-ray diffraction, scanning electron microscopy, and Fourier-transform infrared spectroscopy were used to characterize the synthesized sorbent. All experimental variables were carefully optimized to achieve a high enhancement factor of 107.5-folds with respect to the detection sensitivity of the conventional FAAS. The proposed method's analytical parameters including LOD, LOQ, and linear range were determined as 1.33 μg/L, 4.42 μg/L, and 3.0-40 μg/L, respectively. To assess the applicability and reliability of the developed method, optimal conditions were applied to tap water samples and satisfactory percent recoveries (94-103%) were obtained for the samples spiked at 20 and 30 μg/L. This validated the accuracy and feasibility of the developed method to real samples. The developed method can be described as a simple, efficient, and rapid analytical approach for the accurate determination of trace copper ions in water samples.

Three-dimensional tree-like branched TiO2 nanorods for the highly selective enrichment and determination of lead

Branched titanium dioxide nanorods (B-TiO₂ NRs) grown on fluorine-doped tin oxide glass (FTO) were developed, which can be used as a solid-phase extractant for preconcentration and determination of trace Pb(II) combined with inductively coupled plasma optical emission spectrometry (ICP-OES). The B-TiO₂ NR-based glass substrate displayed excellent adsorptive selectivity and capacity for Pb(II); the maximum adsorption capacity was found to be 168.4 mg⋅g^-1 PB(II) at pH = 5.0. It proved that the primary extraction mechanism was attributed to soft acid/soft base interactions to form complexes for chemisorption. Investigating the adsorption kinetics and isotherms indicated that the pseudo-second-order and Langmuir models can better describe Pb(II) adsorption on the B-TiO₂ NRs. The proposed method presented good linearity from 0.01 to 5 mg⋅L^-1 with a correlation coefficient (R²) of 0.9989 and a low limit of detection (LOD) of 2.2 μg⋅L^-1 for Pb(II) under optimal conditions. The method was successfully applied to Pb(II) determination in foodstuffs with desirable recoveries from 93.18 to 108.1% and good precision with an RSD of less than 12.2%. This work provides a new strategy for selective extraction and determination of Pb(II) in complicated matrix samples.

Kinetics and mechanism of Eu(III) transfer in tributyl phosphate microdroplet/HNO3 aqueous solution system revealed by fluorescence microspectroscopy

In this study, we reveal an Eu(III) extraction mechanism at the interface between HNO₃ and tributyl phosphate (TBP) solutions using fluorescence microspectroscopy. The mass transfer rate constant at the interface is obtained from the analysis of fluorescence intensity changes during the forward and backward extractions at various HNO₃ and TBP concentrations to investigate the reaction mechanism. This result indicates that one nitrate ion reacts with Eu(III) at the interface, whereas TBP molecules are not involved in the interfacial reaction, which is different from the results obtained using the NaNO₃ solution in our previous study. We demonstrate that the chemical species of Eu(III) complex with nitrate ion and TBP in the aqueous solution play an important role for the extraction mechanism. The rate constants of the interfacial reactions in the forward and backward extractions are (4.0-5.0) × 10^-7 m M^-1 s^-1 and (3.2-3.3) × 10^-6 m s^-1, respectively. We expect that our revealed mechanism provides useful and fundamental knowledge for actual solvent extraction.

A Comprehensive Review of Lipidomics and Its Application to Assess Food Obtained from Farm Animals

Lipids are one of the major macronutrients essential for adequate growth and maintenance of human health. Their structure is not only complex but also diverse, which makes systematic and holistic analyses challenging; consequently, little is known regarding the relationship between phenotype and mechanism of action. In recent years, rapid advancements have been made in the fields of lipidomics and bioinformatics. In comparison with traditional approaches, mass spectrometry-based lipidomics can rapidly identify as well as quantify >1,000 lipid species at the same time, facilitating comprehensive, robust analyses of lipids in tissues, cells, and body fluids. Accordingly, lipidomics is now being widely applied in various fields, particularly food and nutrition science. In this review, we discuss lipid classification, extraction techniques, and detection and analysis using lipidomics. We also cover how lipidomics is being used to assess food obtained from livestock and poultry. The information included herein should serve as a reference to determine how to characterize lipids in animal food samples, enhancing our understanding of the application of lipidomics in the field in animal husbandry.

Covalent organic framework-V modified porous polypropylene hollow fiber with detachable dumbbell-shaped structure for stir bar sorptive extraction of benzophenones

Polypropylene hollow fiber is a kind of ideal material for stir bar sorptive extraction (SBSE) which possesses the advantages of porous structure, large specific surface area, high mechanical strength, and good solvent resistance. In this work, a novel SBSE device using the polypropylene hollow fiber-based stir bar with the detachable dumbbell-shaped structure was designed and prepared. Covalent organic framework-V (COF-V), which possesses porous structure, sphere shape with large specific surface area, was synthesized at room temperature and grown on polypropylene hollow fiber by polydopamine modification method. Compared with previous studies which used etched poly(ether ether ketone) as supporting material, polypropylene hollow fiber omitted the complicated, difficult and dangerous pretreatment process with high concentrated sulfuric acid. The immobilization of COF-V on the polypropylene hollow fiber significantly endows them with multiple interaction abilities including hydrophobic interaction and π-π interaction. The stir bar showed good performance and stability for the extraction of four benzophenones including BP-1, BP-6, BP-3 and Ph-BP. By coupling with HPLC-UV, the COF-V@polypropylene hollow fiber based SBSE method showed wide linear range (0.1-200 ng/mL), excellent linearity (R² ≥ 0.9979), high sensitivity (LODs in the range of 0.02-0.03 ng/mL), and good repeatability (RSD ≤ 5.21%). This method was successfully applied to the analysis of benzophenones in soil and sunscreen samples.

Rapid screening of chemical warfare agents (nerve agents) using dimethyl methylphosphonate as simulant substances in beverages by hollow fiber membrane-protected solid phase microextraction followed by corona discharge ion mobility spectrometry

The following work presents a new, rapid, potential to be portable, convenient, and low-cost method using hollow fiber membrane-protected solid phase microextraction followed by corona discharge ion mobility spectrometry which was used for determining dimethyl methylphosphonate in beverages. Response surface methodology based on the design of Box-Behnken was implemented for optimizing the different factors influencing the proposed method for obtaining the best results. Optimal extractions were calculated with 65 µm polydimethylsiloxane-divinylbenzene fiber, fiber equilibration time of 10 min, stirring rate of the sample solution at 750 rpm, and extraction temperature of 50 °C. The proposed technique provided linear range (0.5-50 µg mL^-1), good linearity (>0.991), and repeatability (the relative standard deviations of 5.42% and 8.37% of intra- and inter-day analyses, respectively) under the optimized extraction conditions. Finally, the developed method was successfully used for determining dimethyl methylphosphonate in beverages such as coffee mix, fruit juice, tap water, milk, and tea.

MIL-101(Fe)-derived magnetic porous carbon as sorbent for stir bar sorptive-dispersive microextraction of sulfonamides

Using MIL-101(Fe) as the source of carbon and Fe, a magnetic porous carbon (MPC) material with Fe₃C nanoparticles encapsulated in porous carbon was prepared through one-pot pyrolysis under N₂ atmosphere. With MPC as adsorption material, a stir bar sorptive-dispersive microextraction (SBSDME) method was proposed to extract and preconcentrate sulfonamides (SAs) prior to HPLC-DAD determination. To investigate their extraction ability, different MPC materials were prepared under different carbonization temperatures (600, 700, 800, 900, and 1000 °C). The material prepared under 900 °C (MPC-900) exhibited the highest extraction ability for SAs. The as-prepared MPC materials were also characterized by Raman spectroscopy, scanning electron microscopy, X-ray photoelectron spectroscopy, zeta potential, and other techniques. The main parameters that affect extraction were systematically studied. Under optimal conditions, favorable linearity (R² ≥ 0.9938) and detection limits (0.02-0.04 ng mL^-1) of sulfonamides were obtained. The average recoveries for spiked milk and lake water samples ranged from 76.9 to 109% and from 75.4 to 118% with RSDs of 3.10-9.63% and 1.71-11.3%, respectively. Sulfameter and sulfisoxazole were detected in milk sample. Sulfisoxazole was detected in the lake water sample. The MPC-900 material demonstrated excellent reusability. It can be reused 24 times with peak areas having no obvious decline. The method can be applied to extract ultra-trace compounds in complex sample matrices. Schematic presentation of a stir bar sorptive-dispersive microextraction (SBSDME) by using magnetic porous carbon (MPC) composites as sorbent combined with high-performance liquid chromatography for sensitive analysis of sulfonamides in milk and lake water samples.

Sensors for detecting per- and polyfluoroalkyl substances (PFAS): A critical review of development challenges, current sensors, and commercialization obstacles

Per- and polyfluoroalkyl substances (PFAS) are a class of compounds that have become environmental contaminants of emerging concern. They are highly persistent, toxic, bioaccumulative, and ubiquitous which makes them important to detect to ensure environmental and human health. Multiple instrument-based methods exist for sensitive and selective detection of PFAS in a variety of matrices, but these methods suffer from expensive costs and the need for a laboratory and highly trained personnel. There is a big need for fast, inexpensive, robust, and portable methods to detect PFAS in the field. This would allow environmental laboratories and other agencies to perform more frequent testing to comply with regulations. In addition, the general public would benefit from a fast method to evaluate the drinking water in their homes for PFAS contamination. A PFAS sensor would provide almost real-time data on PFAS concentrations that can also provide actionable information for water quality managers and consumers around the planet. In this review, we discuss the sensors that have been developed up to this point for PFAS detection by their molecular detection mechanism as well as the goals that should be considered during sensor development. Future research needs and commercialization challenges are also highlighted.

[Determination of tetracycline and fluoroquinolone residues in fish by polydopamine nanofiber mat based solid phase extraction combined with ultra performance liquid chromatography-tandem mass spectrometry]

Tetracyclines and fluoroquinolones are common antibacterial drugs used in aquaculture, and their residues may pose a risk to human health. The low concentration of drug residues and complex matrixes such as fats and proteins in aquatic products necessitate the urgent development of efficient sample pretreatment methods. Solid phase extraction (SPE) is the most common sample pretreatment method, in which the core is an adsorbent. Compared with traditional SPE adsorbents, nanofiber mat (NFsM) has more interaction sites because of their large specific surface area. Furthermore, NFsMs modified with specific functional groups can significantly improve the extraction efficiency of tetracyclines and fluoroquinolones. Polydopamine (PDA) is spontaneously synthesized by the oxidative self-polymerization of dopamine-hydrochloride in alkaline solutions (pH>7.5). Because of its rich amino and catechol groups, PDA can form π-π stacking, electrostatic attraction, hydrophobic interaction, and hydrogen bonding interactions with target molecules. By exploiting the above advantages, polystyrene (PS) NFsM, as a template, was prepared by the electrostatic spinning method, and PDA-PS NFsM was obtained by functional modification of PDA through self-polymerization. Fourier transform infrared spectroscopy (FT-IR) and field-emission scanning electron microscopy (FESEM) were used to characterize the synthesized PS NFsM and PDA-PS NFsM. It was proved that PDA was successfully modified on the PS NFsM, with the SEM images revealing a rough outer core shell structure and an inner honeycomb structure. Subsequently, the handmade SPE column with PDA-PS NFsM was completed. A novel and efficient screening analytical method based on PDA-PS NFsM for the simultaneous determination of three tetracyclines (tetracycline (TET), chlortetracycline (CTC), and oxytetracycline (OTC)) and three fluoroquinolones (enrofloxacin (ENR), ciprofloxacin (CIP), and norfloxacin (NOR)) in fish by ultra performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) was established. The SPE procedure was optimized to develop an efficient method for sample preparation. Evaluate parameters including the amount of NFsM usage, ionic strength, flow rate of the sample solution, composition of eluent, and breakthrough volume were investigated. Only (20±0.1) mg of PDA-PS NFsM was sufficient to completely adsorb the targets, and the analytes retained on NFsM could be eluted by 1 mL of formic acid-ethyl acetate (containing 20% methanol) (1∶99, v/v). The residues were redissolved in 0.1 mL 10% methanol aqueous solution containing 0.2% formic acid. In addition, no adjustment of the pH and ionic strength of the sample solutions was required, and the breakthrough volume was 50 mL. The limits of detection (LODs) and limits of quantification (LOQs) of the six target compounds were measured at 3 times and 10 times the signal-to-noise ratio (S/N), respectively. The LODs and LOQs were 0.3-1.5 μg/kg and 1.0-5.0 μg/kg, respectively. The linear ranges of the six target compounds were LOQ-1000 μg/kg, and the coefficient of determination (R²) was greater than 0.999. To evaluate the accuracy and precision, blank spiked samples at three levels (low, medium, and high) were prepared for the recovery experiments, and each level with six parallel samples (n=6). The recoveries ranged from 94.37% to 102.82%, with intra-day and inter-day relative standard deviations of 2.38% to 8.06% and 4.10% to 9.10%, respectively. To evaluate the purification capacity of PDA-PS NFsM, the matrix effects before and after SPE were calculated and compared. Matrix effects before SPE were -12.98% to -38.68%. After the completion of SPEbased on PDA-PS NFsM, the matrix effect of each target analyte was significantly reduced to -2.15% to -7.36%, which proved the significant matrix removal capacity of PDA-PS NFsM. Finally, the practicality of this method was evaluated by using it to analyze real samples. This SPE method based on PDA-PS NFsM is efficient, practical, and environmentally friendly, and it has great potential for use in the routine monitoring of drug residues in fish.

Surface nanodroplet-based nanoextraction from sub-milliliter volumes of dense suspensions

A greener analytical technique for quantifying compounds in dense suspensions is needed for wastewater and environmental analysis, chemical or bio-conversion process monitoring, biomedical diagnostics, and food quality control, among others. In this work, we introduce a green, fast, one-step method called nanoextraction for extraction and detection of target analytes from sub-milliliter dense suspensions using surface nanodroplets without toxic solvents and pre-removal of the solid contents. With nanoextraction, we achieve a limit of detection (LOD) of 10-9 M for a fluorescent model analyte obtained from a particle suspension sample. The LOD is lower than that in water without particles (10-8 M), potentially due to the interaction of particles and the analyte. The high particle concentration in the suspension sample, thus, does not reduce the extraction efficiency, although the extraction process was slowed down up to 5 min. As a proof of principle, we demonstrate the nanoextraction for the quantification of model compounds in wastewater slurry containing 30 wt% solids and oily components (i.e. heavy oils). The nanoextraction and detection technology developed in this work may be used in fast analytical technologies for complex slurry samples in the environment, industrial waste, or in biomedical diagnostics.

Nanoplatform-Integrated Miniaturized Solid-Phase Extraction Techniques: A Critical Review

Preparation of the biological samples is one of the most critical steps in sample analysis. In past decades, the liquid-liquid extraction technique has been used to extract the desired analytes from complex biological matrices. However, solid-phase extraction (SPE) gained popularity due to versatility, simplicity, selectivity, reproducibility, high sample recovery %, solvent economy, and time-saving nature. The superior extraction efficiency of SPE can be attributed to the development of advanced techniques, including the nanosorbents technology. The nanosorbent technology significantly simplified the sample preparation, improved the selectivity, diversified the application, and accelerated the sample analysis. This review critically expands on the to-date advancements reported in SPE with particular regards to the nanosorbent technology.

Nanoscale Affinity Double Layer Overcomes the Poor Antimatrix Interference Capability of Aptamers

Poor antimatrix interference capability of aptamers is one of the major obstacles preventing their wide applications for real-sample detections. Here, we devise a multiple-function interface, denoted as a nanoscale affinity double layer (NADL), to overcome this bottleneck via in situ simultaneous target enrichment, purification, and detection. The NADL consists of an upper aptamer layer for target purification and sensing and a lower nanoscale solid-phase microextraction (SPME) layer for sample enrichment. The targets flowing through the NADL-functionalized surface are instantly million-fold enriched and purified by the sequential extraction of aptamer and SPME. The formation of the aptamer-target complex is greatly enhanced, enabling ultrasensitive detection of targets with minimized interference from the matrix. Taking the fiber-optic evanescent wave sensor as an example, we demonstrated the feasibility and generality of the NADL. The unprecedented detection of limits of 800, 4.8, 40, and 0.14 fM were, respectively, achieved for three representative small-molecule targets with distinct hydrophobicity (kanamycin A, sulfadimethoxine, and di-(2-ethylhexyl) phthalate) and protein target (human serum albumin), corresponding to 2500 to 3 × 10⁸-fold improvement compared to the sensors without the NADL. Our sensors also showed exceptionally high target specificity (>1000) and tunable dynamic ranges simply by manipulating the SPME layer. With these features comes the ability to directly detect targets in diluted environmental, food, and biological samples at concentrations all well below the tolerance limits.

Chitosan-Ni/Fe layered double hydroxide composites as an efficient solid phase extraction sorbent for HPLC-PDA monitoring of parabens in personal care products

There is a dire need for development of efficient and sensitive methods to efficiently screen parabens. In this research, we focused on quantification of four parabens (i.e., methylparaben (MP), ethylparaben (EP), propylparaben (PP), and butyl paraben (BP)) using chitosan intercalated nickel/iron layered double hydroxide (CS-Ni/Fe-LDH) composites as solid phase extraction sorbent prior to HPLC-PDA analysis. CS-Ni/Fe LDH composites with a heterogeneous, porous texture, and coral reef-like structure exhibit appealing extraction efficiency for the target parabens due to the enhanced possibility for the formation of hydrogen bonding and hydrophobic interactions. The performance of the composites was assessed and optimized for solid phase extraction of parabens from standard samples and real samples (rose water, cream, toothpaste, hair serum, and sunscreen). The LDH-SPE-HPLC method exhibited a wide linear range (e.g., 100-50,000 ng L^-1), good linearity (R² ≥ 0.999), and good precision (relative standard deviation (RSD) < 3%). This method successfully enriched selected parabens with remarkable recovery above 85.95% and a good RSD (0.01-2.90%). The quantitation of MP, EP, PP, and BP was made at detection range (and limits of detection (LOD)) of 5-15 (9.8), 11-21 (16.2), 6-18 (12.4), and 10-20 (15.6) ng L^-1, respectively. The prepared composites also displayed excellent performance with enhanced reusability/durability (n = 30 cycles) and reproducibility (n = 5).

The Synthesis of Molecularly Imprinted Polymers on Microcentrifuge Tube Filters for Solid-Phase Extraction and the HPLC-UV Determination of Andrographolides

Molecular imprinting-based solid-phase extraction has been in the spotlight to improve recognition selectivity and detection sensitivity of andrographolides. The synthesis of molecularly imprinted polymers on micro centrifuge tube filters for the extraction and the determination of andrographolides were investigated. Molecularly imprinted polymers were synthesized using the photo-polymerization method for the preconcentration of andrographolides (AD) template molecule using 2,2-dimethoxy-2-phenylacetophenone as initiators, the mixture of 1-dodecanol and toluene solvent, 2-hydroxyethyl methacrylate and ethylene glycol dimethacrylate as functional monomers and cross-linked, respectively. The resultant AD molecularly imprinted polymers (AD-MIPs) were characterized using the Fourier-transform infrared spectrum and scanning electron microscopy. The maximum adsorption of AD-MIPs toward the andrographolides was found to be 85%, and could reach binding equilibrium within 60 min. The sample solution was separated by AD-MIP using solid-phase extraction (SPE). Subsequently, the sample solution was analyzed by the high-performance liquid chromatography (HPLC) method. The AD-MIP could be successfully applied to specifically separate and determine the andrographolides from pharmaceutical products and biological fluid samples with relatively high recoveries (102.01-108.61%). The present method is simple, selective, accurate, and provides a promising alternative to traditional SPE sorbents for the extraction and determination of andrographolides in real samples and biological fluid samples.

Starch-Mg/Al layered double hydroxide composites as an efficient solid phase extraction sorbent for non-steroidal anti-inflammatory drugs as environmental pollutants

Using a co-precipitation method, starch-Mg/Al layered double hydroxide (S-Mg/Al LDH) composites were synthesized. Their physicochemical properties were assessed by Fourier-transform infrared spectroscopy, X-ray diffraction, scanning electron microscopy, and thermo-gravimetric analysis. The quantification of six non-steroidal anti-inflammatory drugs (NSAIDs) was conducted using real samples (e.g., hospital waste water, river water, sewage treatment plant water, and tablet formulations) by gas chromatography-mass spectrometry. For the development of this method, the system was optimized in terms of several key variables (e.g., pH, flow rate, and eluent type/volume). The developed method for NSAIDs exhibited good resolution, sensitivity, reproducibility, and specificity even in complex matrices with limits of detection between 4 and 20 pg/mL. Hence, S-Mg/Al LDH composites were proven to be efficient and fast solid phase extraction (SPE) sorbents for NSAIDs. In addition, each LDH-SPE cartridge showed good reusability without a noticeable change in performance (e.g., up to 30 cycles) and target recoveries between 99.5 - 82.9 %. This work should open up new opportunities for a sesnsitive and sustainable quantitative method for the determination of NSAIDs in complex samples.

Magnetic Polydopamine Modified with Choline-Based Deep Eutectic Solvent for the Magnetic Solid-Phase Extraction of Sulfonylurea Herbicides in Water Samples

A novel magnetic solid-phase extraction technique coupled to ultraperformance liquid chromatography has been developed for separation and preconcentration of four sulfonylurea herbicides (sulfosulfuron, bensulfuron-methyl, pyrazosulfuron-ethyl and halosulfuro-methyl) in aqueous samples. The key point of this method was the application of a novel magnetic nanomaterial that composed of a low eutectic solvent as a shell coated on the magnetic core modified by polydopamine. The extensive active sites outside the low eutectic solvent can effectively adsorb the target herbicide in the extraction process. The obtained magnetic adsorbent was characterized with fourier transform infrared spectrometry, scanning electron microscopy and vibrating sample magnetometer. The influence parameters relevant to this method were optimized. Under the optimum conditions, good linearities could be obtained within the range of 1.0-200 μg L-1 for all analytes, with correlation coefficients ≥0.9908. The limit of detections of the method was between 0.0074 and 0.0100 μg L-1 and the relative standard deviations were 1.1-3.6%. The enrichment factor is 66.6. In the final experiment, the proposed method was successfully applied to the analysis of sulfonylurea herbicides residue in environment and drinking-water samples, and the obtained recoveries were between 70.6% and 109.4%.

Fabrication of edge-curled petals-like covalent organic frameworks and their properties for extracting indole alkaloids from complex biological samples

In this study, a functionalized covalent-organic framework (COF) was first synthesized using porphyrin as the fabrication unit and showed an edge-curled, petal-like and well-ordered structure. The synthesized COF was then introduced to prepare porous organic polymer monolithic materials (POPMs). Two composite POPM/COF monolithic materials with rod shapes, referred to as sorbent A and sorbent B, were prepared in stainless steel tubes using different monomers. Sorbents A and B exhibited relatively uniform porous structures and enhanced specific surface areas of 153.14 m²/g and 80.01 m²/g, respectively. The prepared composite monoliths were used as in-tube solid-phase extraction (SPE) sorbents combined with HPLC for the on-line extraction and quantitative analytical systems. Indole alkaloids (from Catharanthus roseus G. Don and Uncaria rhynchophylla (Miq.) Miq. Ex Havil.) contained in mouse plasma were extracted and quantitatively analyzed using the online system. The two composite multifunctional monoliths showed excellent clean-up ability for complex biological matrices, as well as superior selectivity for target indole alkaloids. Method validation showed that the RSD values of the repeatability (n=6) were ≤ 3.46%, and the accuracy expressed by the spiked recoveries was in the ranges of 99.38%–100.91% and 96.39%–103.50% for vinca alkaloids and Uncaria alkaloids, respectively. Furthermore, sorbents A and B exhibited strong reusability, with RSD values ≤ 5.32%, which were based on the peak area of the corresponding alkaloids with more than 100 injections. These results indicate that the composite POPM/COF rod-shaped monoliths are promising media as SPE sorbents for extracting trace compounds in complex biological samples.

•

Edge-curled petals-like COF was synthesized using porphyrin as the fabrication unit.

•

In-tube monolithic POMP/COF composite SPE sorbents with rod-shape were fabricated.

•

The in-tube sorbents were used to extract hence indole alkaloids from complex samples.

•

The two homemade sorbents show strong reusability of more than 100 times.

Effective Enrichment and Quantitative Determination of Trace Hg2+ Ions Using CdS-Decorated Cellulose Nanofibrils

Water pollution caused by metal contamination is of serious concern. Direct determination of trace metal ions in real water samples remains challenging. A sample preparation technique is a prerequisite before analysis. Herein, we report the facile water-based hydrothermal synthesis of cadmium sulfide nanoparticles on a cellulose nanofiber surface to prepare a new adsorbent material. Field emission scanning electron microscopy, high-resolution tunneling electron microscopy, elemental mapping and X-ray photoelectron microscopy were used to characterize the surface morphology, structural determination, elemental composition and nature of bonding. The nanoadsorbent (cadmium-sulfide-decorated cellulose nanofibrils (CNFs@CdS)) was employed for the solid-phase extraction and determination of trace Hg(II) from aqueous media. The experimental conditions were optimized systematically and the data show a good Hg(II) adsorption capacity of 126.0 mg g⁻¹. The CNFs@CdS adsorbent shows the selective removal of Hg(II) accordingly to the hard and soft acid–base theory of metal–ligand interaction. A high preconcentration limit of 0.36 µg L⁻¹ was obtained with a preconcentration factor of 580. The lowest level of trace Hg(II) concentration, which was quantitatively analyzed by the proposed method, was found to be 0.06 µg L⁻¹. No significant interferences from the sample matrix were observed in the extraction of Hg(II). Analysis of the standard reference material (SRM 1641d) was carried out to validate the proposed methodology. Good agreement between the certified and observed values indicates the applicability of the developed methodology for the analysis of Hg(II) in tap water, river water and industrial wastewater samples.

Applying Al2O3@Ag@trithiocyanuric acid as an efficient metal ion scavenger for the selective extraction of iron (III) and lead (II) from environmental waters

In the present study, silver (Ag) atoms were chemically deposited on γ-alumina (Al₂O₃) nanospheres to be further functionalized with trithiocyanuric acid (TTC). The result was Al₂O₃@Ag@TTC composites, which were used for the selective extraction and preconcentration of Fe (III) and Pb (II) ions in seawater and river water samples. TTC is a potent scavenger of heavy metal ions with multiple nitrogen- and sulfur-containing functional groups. The concentrations of analytes were determined by flame atomic absorption spectrometry, and the structure of the synthetic adsorbent was characterized by spectral and microscopic techniques. Furthermore, the fundamental parameters influencing the extraction and desorption of the target ions were evaluated. Under optimized conditions, the calibration curve was linear in the range of 10-100 ng mL^-1 for both analytes. The detection limits of the proposed method for Fe (III) and Pb (II) ions were 1.5 ng mL^-1 and 0.8 ng mL^-1, respectively, with a relative standard deviation of less than 6.1% (n = 7). Moreover, the proposed method tolerated salinities of up to 50.0 g L^-1 without exhibiting any decrease in selectivity or recovery. The developed method was successfully applied to extract Fe (III) and Pb (II) ions from seawater and river water samples. The extraction recovery rates of the spiked ions were at least 93% for Fe (III) and 97 % for Pb (II).

Pipette-tip SPE based on Graphene/ZnCr LDH for Pb(II) analysis in hair samples followed by GFAAS

In this work, a nanocomposite of ZnCr layered double hydroxide (ZnCr LDH) and graphene oxide (GO) was successfully assembled. An efficient pipette-tip solid-phase extraction (PT-SPE) based on GO/ZnCr LDH followed by GFAAS analysis was used for to preconcentrate Pb(II) in hair samples. Hair samples were treated using acid digestion to make the solid samples suitable for performing the PT-SPE procedure and decrease the interactions between Pb(II) ions and the sample matrix. The sorbent was characterized by FT-IR, SEM, TEM, EDX, elemental mapping, and XRD. Effective extraction parameters were thoroughly investigated. Under the best conditions, the calibration plot was linear within the range of 0.5-15 ng mL^-1 (R² = 0.991). Preconcentration factor (PF) of 10 and absolute recovery (%) of 100% were obtained. LOD and LOQ were found to be 0.1 μg g^-1 and 0.5 μg g^-1, respectively. The intra-day and inter-day precisions (n = 3) at the concentrations of 2.0 and 10 ng mL^-1 were less than 6.8% and 12.5%, respectively. Finally, the method efficiency was investigated for the analysis of Pb(II) in hair samples, and good relative recoveries (RR%) were obtained within the range of 92%-104%.

A 96-Monolithic inorganic hollow fiber array as a new geometry for high throughput solid-phase microextraction of doxorubicin in water and human urine samples coupled with liquid chromatography-tandem mass spectrometry

Innovations in extraction phases, extraction modes and hyphenated instrument configurations, are the most important issues to address for progress in the solid phase microextraction (SPME) methodology. In this regard, we have embarked on the development of a novel biocompatible 96-monolithic inorganic hollow fiber (96-MIHF) array as a new configuration for high-throughput SPME on a 96-well plate system. An arrangement of highly ordered 96 titania/Hydroxyapatite (TiO₂/HAP) nanocomposite hollow fibers and corresponding stainless-steel needles on a Teflon plate holder were used as the extraction module. The inorganic hollow fibers were prepared via a rapid and reproducible template approach (Polypropylene hollow fiber) in combination with a sol-gel method in the presence of polyvinyl alcohol (PVA), as a network maker. The hollow fiber-shape sorbents were obtained with excellent precision by weight (RSD% = 4.98, n = 10) and length (RSD% = 1.08, n = 10) criteria. The proposed design can overcome a number of geometrically dependent drawbacks of conventional high-throughput SPME methods, mainly the ones related to sorbent amount and surface area due to possessing inner/outer surfaces without additional internal supports. The SPME platform, for the first time, was successfully applied for the extraction and preconcentration of doxorubicin from urine and water media without requiring sample preparation and free from significant matrix effect. The extracted analyte was analyzed by liquid chromatography-ion trap tandem mass spectrometry (LC-MS/MS). Highly satisfactory analytical figures of merit were obtained under optimized conditions. The limit of detection (LOD), limit of quantification (LOQ) and linearity of determination were 0.1 ng mL^-1, 0.25 ng mL^-1 and 0.25 to 4000 ng mL^-1, respectively. The interday, intraday and inter sorbent precisions for three concentration levels ranged from 2.01 to 8.09 % (n = 3), 1.02 to 8.65 % (n = 5) and 0.99 to 1.02% (n = 15), respectively. The mean intra-well RSD value for 96 individual wells in 96-MIHF-SPME-LC-MS/MS (n = 3) at the medium concentration level was 7.81%.

Micellar extraction with vesicle coated multi-walled carbon nanotubes to assist the dispersive micro-solid-phase extraction of natural phenols in Dendrobium

Here, catanionic surfactant vesicles were prepared by varying the types and compositions of anions and cations and the number of alkyl tails of the surfactants. The formed vesicles were employed to disaggregate and stabilize multiwalled carbon nanotubes bundles in aqueous solutions. Furthermore, the vesicle coated carbon nanotubes were used as the adsorbent in the dispersive micro-solid phase extraction. Additionally, micellar extraction was employed for the sample pre-extraction to avoid the use of toxic organic extraction solvents. The relative parameters that affect the extraction efficiency of targets were optimized using response surface methodology. Under the optimal microextraction conditions, the analytical performance of the established method was evaluated. The limits of detection (2.3-13 ng/mL) and quantification (7.6-42 ng/mL), inter- and intra- day precision (1.2-4.0 %, 2.0-5.0 %), and spiked recovery values (80-91 %) were obtained. The proposed method showed high sensitivity, precision and trueness. It was successfully applied to analyze phenols in Dendrobium genus samples.

Mass spectrometry-based lipidomics in food science and nutritional health: A comprehensive review

With the advance in science and technology as well as the improvement of living standards, the function of food is no longer just to meet the needs of survival. Food science and its associated nutritional health issues have been increasingly debated. Lipids, as complex metabolites, play a key role both in food and human health. Taking advantages of mass spectrometry (MS) by combining its high sensitivity and accuracy with extensive selective determination of all lipid classes, MS-based lipidomics has been employed to resolve the conundrum of addressing both qualitative and quantitative aspects of high-abundance and low-abundance lipids in complex food matrices. In this review, we systematically summarize current applications of MS-based lipidomics in food field. First, common MS-based lipidomics procedures are described. Second, the applications of MS-based lipidomics in food science, including lipid composition characterization, adulteration, traceability, and other issues, are discussed. Third, the application of MS-based lipidomics for nutritional health covering the influence of food on health and disease is introduced. Finally, future research trends and challenges are proposed. MS-based lipidomics plays an important role in the field of food science, promoting continuous development of food science and integration of food knowledge with other disciplines. New methods of MS-based lipidomics have been developed to improve accuracy and sensitivity of lipid analysis in food samples. These developments offer the possibility to fully characterize lipids in food samples, identify novel functional lipids, and better understand the role of food in promoting healt.

Direct immersion single-drop microextraction of semi-volatile organic compounds in environmental samples: A review

Single-drop microextraction (SDME) techniques are efficient approaches to pretreatment of aqueous samples. The main advantage of SDME lies in the miniaturization of the solvent extraction process, minimizing the hazards associated with the use of toxic organic solvents. Thus, SDME techniques are cost-effective, and represent less harm to the environment, subscribing to green analytical chemistry principles. In practice, two main approaches can be used to perform SDME - direct immersion (DI)-SDME and headspace (HS)-SDME. Even though the DI-SDME has been shown to be quite effective for extraction and enrichment of various organic compounds, applications of DI-SDME are normally more suitable for moderately polar and non-polar semi-volatile organic compounds (SVOCs) using organic solvents which are immiscible with water. In this review, we present a historical overview and current advances in DI-SDME, including the common analytical tools which are usually coupled with DI-SDME. The review also focuses on applications concerning SVOCs in environmental samples. Currents trends in DI-SDME and possible future direction of the procedure are discussed.