High-Throughput Screening and Quantitation of Target Compounds in Biofluids by Coated Blade Spray-Mass Spectrometry

Development and functionalization of electrospun fiber coated thin film microextraction devices for rapid mass spectrometric determination of biologically important polar molecules

Rapid diagnosis of diseases is one of the challenging areas in clinical research. From the analytical chemist's perspective, the main challenges are isolating the compounds from the bio-specimen and lengthy analysis times. In this regard, solid phase microextraction offers a platform to address the abovementioned challenges. Moreover, its sharp tip-thin film geometry, known as coated blade spray (CBS), can enhance the extraction and act as an ionization source in direct mass spectrometric analysis. In this study, a new CBS device specifically designed for polar analytes was prepared and optimized to determine urinary metabolites. For this purpose, polyacrylonitrile (PAN) was selected as a base polymer as it can be electrospun to form a nanofibrous structure, and it can be modified with weak ion exchange moieties to interact with polar analytes. Following the electrospinning of PAN, hydrolysis was optimized, and conditions leading to sufficient extraction enhancement without dissolving the polymer were obtained when probes were treated with 5.0 M of NaOH for 2.5 h. Using the coated blades prepared as explained, the evaluation of various extraction conditions showed that 5 min is sufficient for equilibrium extraction. In addition, the solution's ionic strength and pH significantly affect the extraction. Optimum sorption was obtained at no salt added and pH 7.0 conditions. The CBS-MS optimization showed that 10.0 µL of ACN/MeOH/H2O (40:40:20, v/v/v) with formic acid kept for 15 seconds on the blade before voltage application leads to the highest signal. The limits of quantification of the analytes are between 50 and 100 ng/mL.

Coated Blade Spray Ion Mobility Spectrometry

Coated blade spray (CBS) is a microextraction technology with blades that serve as both the extraction device and the electrospray ionization (ESI) emitter. CBS is designed for easy and rapid extraction of analytes in complex matrices as well as ESI directly from the blade. The technology selectively enriches the components of interest on a coated metal blade. The coating consists of a selective polymer. So far, CBS has only been coupled with mass spectrometry but never with ion mobility spectrometry (IMS), where ions are separated and detected based on their ion mobility in a drift gas under the influence of an electric field, while instrumentation is compact and easy to operate so that the advantages of CBS can be particularly well exploited. Therefore, this work focuses on coupling CBS with our previously described ESI-IMS. The ion mobility spectrometer has a drift length of only 75 mm and provides a high resolving power of RP = 100. In this work, preliminary measurements of CBS-IMS are presented. In particular, the detection of benzodiazepines and ketamine in drinks and the pesticide isoproturon in water samples is shown to demonstrate the feasibility of CBS-IMS.

Ambient ionisation mass spectrometry for drug and toxin analysis: A review of the recent literature

Ambient ionisation mass spectrometry (AIMS) is a form of mass spectrometry whereby analyte ionisation occurs outside of a vacuum source under ambient conditions. This enables the direct analysis of samples in their native state, with little or no sample preparation and without chromatographic separation. The removal of these steps facilitates a much faster analytical process, enabling the direct analysis of samples within minutes if not seconds. Consequently, AIMS has gained rapid popularity across a diverse range of applications, in particular the analysis of drugs and toxins. Numerous fields rely upon mass spectrometry for the detection and identification of drugs, including clinical diagnostics, forensic chemistry, and food safety. However, all of these fields are hindered by the time-consuming and laboratory-confined nature of traditional techniques. As such, the potential for AIMS to resolve these challenges has resulted in a growing interest in ambient ionisation for drug and toxin analysis. Since the early 2000s, forensic science, diagnostic testing, anti-doping, pharmaceuticals, environmental analysis and food safety have all seen a marked increase in AIMS applications, foreshadowing a new future for drug testing. In this review, some of the most promising AIMS techniques for drug analysis will be discussed, alongside different applications of AIMS published over a 5-year period, to provide a summary of the recent research activity for ambient ionisation for drug and toxin analysis.

Mixed-mode cationic exchange sorptive tapes combined with direct infusion mass spectrometry for determining opioids in saliva samples

This article describes the synthesis of mixed-mode cationic exchange (MCX) tapes as sorptive phases in bioanalysis, and it faces the determination of methadone and tramadol in saliva as the model analytical problem. The tapes are synthesized using aluminum foil as substrate, which is subsequently covered with double-sided adhesive tape where the MCX particles (ca. 1.4 ± 0.2 mg) finally adhere. MCX particles allow the extraction of the analytes at the physiological pH, where both drugs are positively charged, minimizing the potential co-extraction of endogenous matrix compounds. The extraction conditions were studied considering the main variables (e.g. ionic strength, extraction time, sample dilution). Under the optimum conditions and using direct infusion mass spectrometry as the instrumental technique, detection limits as low as 3.3 μg·L^-1 were obtained. The precision calculated at three different levels, and expressed as relative standard deviation, was better than 3.8%. The accuracy, expressed as relative recoveries, ranged from 83 to 113%. The method was finally applied to determine tramadol in saliva samples from patients under medical treatment. This approach opens the door to easily preparing sorptive tapes based on commercial (or ad-hoc synthesized) sorbent particles.

On-Demand Portable Paper-Based Electrospray Ionization Mass Spectrometry for High-Sensitivity Analysis of Complex Samples

Paper spray ionization has been demonstrated to be the most promising substrate-based source, but this technique suffers from the low desorption efficiency of target compounds and poor portability. In the current study, we describe a portable paper-based electrospray ionization (PPESI) in which a piece of triangle paper and adsorbent are packed sequentially into a modified disposable micropipette tip. This source not only captures the feature of paper spray and adsorbent for highly efficient suppression of sample matrixes for target compound analysis but also takes advantage of a micropipette tip to prevent spray solvent from rapid evaporation. The performance of developed PPESI depends on the type and amount of packed adsorbent, paper substrate, and spray solvent and applied voltage. Moreover, by contrast to other related sources, the analytical sensitivity and the spray duration of PPESI in tandem with MS have been improved by factors of 2.8-32.3 and 2.0-13.3, respectively. Based on its high accuracy (>96%) and precision (less than 3% relative standard deviation), the PPESI coupled to a mass spectrometer has been used to determine diverse therapeutic drugs and pesticides in complex biological (e.g., whole blood, serum, and urine) and food (e.g., milk and orange juice) matrixes, and the limits of detection and quantification were 2-4 pg mL^-1 and 7-13 pg mL^-1, respectively. Taking the portability, high sensitivity, and repeatability, the technique may be a promising alternative for complex sample analysis.

Direct Coupling of SPME to Mass Spectrometry

Solid-phase microextraction devices are normally analyzed by gas or liquid chromatography. Their use has become increasingly widespread since their introduction in 1990, and nowadays most analytical laboratories use or have used SPME as an efficient and green method to perform analyte extraction and sample clean-up in one step. The SPME technique is intrinsically flexible, and allows for a high degree of optimization with regard to the extracting phase, as well as the way sample is analyzed. Since its introduction, researchers have been trying different ways to transfer analytes extracted from the solid phase to a mass spectrometer, with the aim to increase throughput and reduce solvent, gas usage and costs associated with conventional chromatographic techniques. Furthermore, but not less important, for pure fun of developing new, more efficient and sensitive analytical strategies! This chapter aims at providing a comprehensive overview of the most relevant non-chromatographic mass spectrometric approaches developed for SPME. Technical aspects of each SPME-MS approach will be discussed, highlighting their advantages, disadvantages and future potential developments. Particular emphasis will be given on the most recent direct coupling approaches using novel ionization approaches, and a concise overview of the existing applications will also be provided.

On-line aptamer affinity solid-phase extraction direct mass spectrometry for the rapid analysis of α-synuclein in blood

On-line aptamer affinity solid-phase extraction direct mass spectrometry (AA-SPE-MS) is presented for the rapid purification, preconcentration, and characterization of α-synuclein (α-syn), which is a protein biomarker related to Parkinson's disease. Valve-free AA-SPE-MS is easily implemented using the typical SPE microcartridges and instrumental set-up necessary for on-line aptamer affinity solid-phase extraction capillary electrophoresis-mass spectrometry (AA-SPE-CE-MS). The essential requirement is substituting the application of the separation voltage by a pressure of 100 mbar for mobilization of the eluted protein through the capillary towards the mass spectrometer. Under optimized conditions with recombinant α-syn, repeatability is good in terms of migration time and peak area (percent relative standard deviation (%RSD) values (n = 3) are 1.3 and 6.6% at 1 μg mL^-1, respectively). The method is satisfactorily linear between 0.025 and 5 μg mL^-1 (R² > 0.986), and limit of detection (LOD) is 0.02 μg mL^-1 (i.e. 1000, 500, and 10 times lower than by CE-MS, direct MS, and AA-SPE-CE-MS, respectively). The established AA-SPE-MS method is further compared with AA-SPE-CE-MS, including for the analysis of α-syn in blood. The comparison discloses the advantages and disadvantages of AA-SPE-MS for the rapid and sensitive targeted analysis of protein biomarkers in biological fluids.

Comparison of different approaches for direct coupling of solid-phase microextraction to mass spectrometry for drugs of abuse analysis in plasma

The direct coupling of solid-phase microextraction (SPME) to mass spectrometry (MS) (SPME-MS) has proven to be an effective method for the fast screening and quantitative analysis of compounds in complex matrices such as blood and plasma. In recent years, our lab has developed three novel SPME-MS techniques: SPME-microfluidic open interface-MS (SPME-MOI-MS), coated blade spray-MS (CBS-MS), and SPME-probe electrospray ionization-MS (SPME-PESI-MS). The fast and high-throughput nature of these SPME-MS technologies makes them attractive options for point-of-care analysis and anti-doping testing. However, all these three techniques utilize different SPME geometries and were tested with different MS instruments. Lack of comparative data makes it difficult to determine which of these methodologies is the best option for any given application. This work fills this gap by making a comprehensive comparison of these three technologies with different SPME devices including SPME fibers, CBS blades, and SPME-PESI probes and SPME-liquid chromatography-MS (SPME-LC-MS) for the analysis of drugs of abuse using the same MS instrument. Furthermore, for the first time, we developed different desorption chambers for MOI-MS for coupling with SPME fibers, CBS blades, and SPME-PESI probes, thus illustrating the universality of this approach. In total, eight analytical methods were developed, with the experimental data showing that all the SPME-based methods provided good analytical performance with R ² of linearities larger than 0.9925, accuracies between 81% and 118%, and good precision with an RSD% ≤ 13%.

Potential of desorption electrospray ionization and paper spray ionization with high-resolution mass spectrometry for the screening of sports doping agents in urine

In this work, desorption electrospray ionization and paper spray ionization both with high-resolution mass spectrometry (DESI-HRMS and PSI-HRMS) were explored for the fast and direct analysis of stimulants and diuretics in urine samples. The analysis was performed at a resolution of 70 000 FWHM (m/z 200) using a quadrupole-Orbitrap mass spectrometer in full scan acquisition mode, detecting stimulants and diuretics in positive and negative ion modes, respectively. The most critical parameters affecting the desorption and ionization efficiencies of compounds were optimized, paying particular attention to the optimization of the spray solvent for PSI-HRMS analysis and to the selection of the DESI sample substrate. For stimulants, the PSI-HRMS method performed better than DESI-HRMS, allowing the direct analysis of raw urine samples with better signal-to-noise ratios than DESI. However, results obtained for diuretics were not as satisfactory as we expected. The PSI-HRMS method was applied to the screening of 52 stimulants for doping control purposes, providing satisfactory detectability for most of them at the Minimum Reporting Level (MRL) in less than 2 minutes for each single analysis. Despite the advantages offered by the PSI-HRMS method, in this study is also included a discussion on the limitations observed because of the presence of interference for some compounds.

Understanding the effect of spatial positioning of coated blade spray devices relative to the mass spectrometry inlet on different instrument platforms and its application to quantitative analysis of fentanyl and related analogs

RATIONALE

We evaluated the effect that the spatial positioning of coated-blade spray (CBS) devices with respect to the mass spectrometry (MS) inlet has when coupling to diverse MS platforms (i.e., triple quadrupole, linear ion trap and time of flight). Furthermore, as a proof of concept, we evaluated CBS-MS as a tool for quantitation of fentanyl and four analogues on said instruments.

METHODS

Custom-made MS interfaces were made to accurately position the blade in front of the MS inlet. CBS devices, coated with hydrophilic-lipophilic balanced particles, were used for both the optimization of the CBS position and the quantitation of fentanyl and analogues in urine and plasma samples on all instruments.

RESULTS

The SCIEX triple quadrupole instrument was the most sensitive to the position of the blade due to the presence of a curtain gas flowing laminarly out of the MS inlet. After optimization, the analytical capabilities of CBS on each instrument were assessed and the results obtained on both SCIEX and Waters platforms matched the performance obtained using a more advanced instrument by ThermoFisher Scientific. Furthermore, excellent figures of merit were attained for the quantitation of fentanyl and analogues on both triple quadrupole and linear ion trap platforms.

CONCLUSIONS

We demonstrated that optimization of MS parameters on different instrument vendors and front ends, such as the position of the CBS tip regarding the MS inlet, is vital to exploit the full quantitative potential of this technology. Application of the technology to screen and quantify fentanyl and analogues showed great potential when considering its coupling with portable mass spectrometers for therapeutic drug monitoring and point-of-care applications.

Ambient Ionization Mass Spectrometry: Application and Prospective

Mass spectrometry (MS) is a formidable analytical tool for the analysis of non-polar to polar compounds individually and/or from mixtures, providing information on the molecular weights and chemical structures of the analytes. During the last more than one-decade, ambient ionization mass spectrometry (AIMS) has developed quickly, producing a wide range of platforms and proving scientific improvements in a variety of domains, from biological imaging to quick quality control. These methods have made it possible to detect target analytes in real time without sample preparation in an open environment, and they can be connected to any MS system with an atmospheric pressure interface. They also have the ability to analyze explosives, illicit drugs, disease diagnostics, drugs in biological samples, adulterants in food and agricultural products, reaction progress, and environmental monitoring. The development of novel ambient ionization techniques, such as probe electrospray ionization, paper spray ionization, and fiber spray ionization, employed even at picolitre to femtolitre solution levels to provide femtogram to attogram levels of the target analytes. The special characteristic of this ambient ion source, which has been extensively used, is the noninvasive property of PESI of examination of biological real samples. The results in the current review supports the idea that AIMS has emerged as a pioneer in MS-based approaches and that methods will continue to be developed along with improvements to existing ones in the near future.

Rapid Screening and Quantitation of Drugs of Abuse by Both Positive and Negative Modes via Coated Blade Spray-Mass Spectrometry

Solid-phase microextraction (SPME)-direct mass spectrometry (MS) has proven to be an efficient tool for the rapid screening and quantitation of target compounds at trace levels. However, it is challenging to perform screening using both positive and negative modes in one analytical run without compromising scanning speed and detection sensitivity. To take advantage of the special geometry of a coated blade spray (CBS) blade, which consists of two flat sides coated with the same SPME coating, we developed a CBS-MS method that enables desorption and ionization to be performed in positive ionization mode on one side of a coated blade and negative ionization mode on the other side of the same blade. By simply flipping the blade 180°, MS analysis in both ionization modes on different sides can be completed in 40 s. Combining this approach with an automated Concept 96-blade-based SPME system allowed analysis for one sample in positive and negative modes to be completed in less than 1 min. The workflow was optimized by using a biocompatible polyacrylonitrile as an undercoating layer and a binder of polyacrylonitrile/hydrophilic-lipophilic balance (HLB) particles, which enabled the rapid analysis of 20 drugs of abuse in saliva samples in both positive and negative modes. The proposed method provided low limits of quantification (between 0.005 and 10 ng/mL), with calibration linear correlation coefficients ⩾ 0.9925, accuracy between 72% and 126%, and relative precision < 15% for three validation points.

Deployable Mass Spectrometry for Rapid On-Site Bioanalysis

Benchtop liquid chromatography (LC)–mass spectrometry (LC–MS) and benchtop gas chromatography–MS (GC–MS) have been the gold standard in bioanalysis for decades, employed in clinical, forensic, and anti-doping laboratories worldwide. However, traditional instrumentation is subject to limitations that severely restrict the speed at which samples can be analyzed, the ease with which materials can be prepared, and the location where the analysis must be performed. With the advent of ambient ionization and portable mass spectrometers, the ability to perform rapid, on-site analysis is fast becoming a reality. Without the need for extensive sample preparation, analysis times as low as several seconds, and the ability to perform analysis remote from the laboratory, deployable mass spectrometers have the potential to revolutionize bioanalysis. However, several challenges must be tackled before this innovative technology can be widely adopted.

Coated Blade Spray-Mass Spectrometry as a New Approach for the Rapid Characterization of Brain Tumors

Brain tumors are neoplasms with one of the highest mortality rates. Therefore, the availability of methods that allow for the quick and effective diagnosis of brain tumors and selection of appropriate treatments is of critical importance for patient outcomes. In this study, coated blade spray-mass spectrometry (CBS-MS), which combines the features of microextraction and fast ionization methods, was applied for the analysis of brain tumors. In this approach, a sword-shaped probe is coated with a sorptive material to enable the extraction of analytes from biological samples. The analytes are then desorbed using only a few microliters of solvent, followed by the insertion of the CBS device into the interface on the mass spectrometer source. The results of this proof-of-concept experiment confirmed that CBS coupled to high-resolution mass spectrometry (HRMS) enables the rapid differentiation of two histologically different lesions: meningiomas and gliomas. Moreover, quantitative CBS-HRMS/MS analysis of carnitine, the endogenous compound, previously identified as a discriminating metabolite, showed good reproducibility with the variation below 10% when using a standard addition calibration strategy and deuterated internal standards for correction. The resultant data show that the proposed CBS-MS technique can be useful for on-site qualitative and quantitative assessments of brain tumor metabolite profiles.

FIELDABLE MASS SPECTROMETRY FOR FORENSIC SCIENCE, HOMELAND SECURITY, AND DEFENSE APPLICATIONS

Mass spectrometry is commonly used in forensic chemistry laboratories for sensitive, definitive analysis. There have been significant efforts to bring mass spectrometry analysis on-site through the development of ruggedized, fieldable instruments. Testing samples in the field is of particular interest in forensic science, homeland security, and defense applications. In forensic chemistry, testing seized drugs in the field can significantly improve efficiencies in processing of related criminal cases. The screening of passengers and luggage at transportation hubs is a critical need for homeland security for which mass spectrometry is well suited to provide definitive answers with low false positive rates. Mass spectrometry can yield reliable data for military personnel testing sites for potential chemical weapons release. To meet the needs of the forensic and security communities fieldable mass spectrometers based on membrane inlet systems and hybrid gas chromatography systems have been developed and commercialized. More recently developed ambient ionization mass spectrometry methods can eliminate the time, equipment, and expertise associated with sample preparation, and so are especially appealing for on-site analysis. We describe the development of fieldable mass spectrometry systems, with emphasis on commercially available systems that have been deployed for on-site analysis of seized drugs, chemical warfare agents, explosives, and other analytes of interest to the forensic and security communities. © 2020 John Wiley & Sons Ltd. Mass Spec Rev.

Peptide and protein assays using customizable bio-affinity arrays combined with ambient ionization mass spectrometry

High-throughput identification and quantification of protein/peptide biomarkers from biofluids in a label-free manner is achieved by interfacing bio-affinity arrays (BAAs) with nano-electrospray desorption electrospray ionization mass spectrometry (nano-DESI-MS). A wide spectrum of proteins and peptides ranging from phosphopeptides to cis-diol biomolecules as well as thrombin can be rapidly extracted via arbitrarily predefined affinity interactions including coordination chemistry, covalent bonding, and biological recognition. An integrated MS platform allows continuous interrogation. Profiling and quantitation of dysregulated phosphopeptides from small-volume (∼5 μL) serum samples has been successfully demonstrated. As a front-end device adapted to any mass spectrometer, this MS platform might hold much promise in protein/peptide analysis in point-of-care (POC) diagnostics and clinical applications.

Customizable bio-affinity arrays were interfaced with ambient ionization mass spectrometry for high-throughput assays of protein/peptide biomarkers in biofluids.

Mechanism behind the paper spray chemical ionization phenomenon and the choice of solvent

Paper spray chemical ionization (PSCI) combined with mass spectrometry has been proposed as a sensitive method for the analysis of nonpolar aromatic compounds; however, the mechanism behind PSCI is not well understood. In the present study, the evidence for the occurrence of corona discharge is provided and its mechanism is proposed. Photographs taken with a highly sensitive camera evidently demonstrate the occurrence of corona discharge at the end of the triangular shape tip when a nonpolar solvent such as hexane was used at an applied potential of 6-7 kV. Nevertheless, corona discharge was not observed in the presence of a polar solvent. The occurrence of the corona discharge was attributed to charge accumulation in the dielectric layer generated by the nonpolar solvent on the fibers of the paper tip. Specifically, corona discharge was generated at the tip end when the charge approached a critical threshold. In the presence of a polar solvent, however, the dielectric layer was not generated and, hence, corona discharge was not observed. Based on this information, three nonpolar solvents were selected and their sensitivity for analyzing the phenanthrene and maltene fractions of crude oil was evaluated. Chlorobenzene provided the highest signal abundance; therefore, it was suggested as the optimum solvent for PSCI. Notably, the fundamental understanding of corona discharge in PSCI acquired in this study provides a basis for further improvement of this technique by way of surface modification.

Hyphenated sample preparation-electrospray and nano-electrospray ionization mass spectrometry for biofluid analysis

Stand-alone electrospray ionization mass spectrometry (ESI-MS) has been advancing through enhancements in throughput, selectivity and sensitivity of mass spectrometers. Unlike traditional MS techniques which usually require extensive offline sample preparation and chromatographic separation, many sample preparation techniques are now directly coupled with stand-alone MS to enable outstanding throughput for bioanalysis. In this review, we summarize the different sample clean-up and/or analyte enrichment strategies that can be directly coupled with ESI-MS and nano-ESI-MS for the analysis of biological fluids. The overview covers the hyphenation of different sample preparation techniques including solid phase extraction (SPE), solid phase micro-extraction (SPME), slug flow micro-extraction/nano-extraction (SFME/SFNE), liquid extraction surface analysis (LESA), extraction electrospray, extraction using digital microfluidics (DMF), and electrokinetic extraction (EkE) with ESI-MS and nano-ESI-MS.

Fabrication of a "Selenium Signature" Chemical Probe-Modified Paper Substrate for Simultaneous and Efficient Determination of Biothiols by Paper Spray Mass Spectrometry

Significant efforts have been made to develop robust and reliable methods for simultaneous biothiols determination in different matrices, but there still exist the problems such as easy oxidation, tedious derivatization, and difficulty in discrimination, which brings unsatisfactory results in their accuracy and fast quantification in biological samples. To overcome these problems, a simultaneous biothiols detection method combining a "selenium signature" chemical probe and paper spray mass spectrometry (PS-MS) was proposed. In the strategy, the modified-paper substrate is used to enhance the analytical performance. Chemical probe Ebselen-NH₂ that has a specific response to biothiols was designed and covalently fixed on the surface of an oxidized paper substrate. By the identification of derivatized product with distinctive selenium isotope distribution and employment of the optimized PS-MS method, qualitative and quantitative analysis of five biothiols including glutathione (GSH), cysteine (Cys), cysteinylglycine (CysGly), N-acetylcysteine (Nac), and homocysteine (Hcy) were realized. Biothiols in plasma and cell lysates were measured with satisfactory results. The established method not only provides a novel protocol for simultaneous determination of biothiols, but also is helpful for understanding the biological and clinical roles played by these bioactive small molecules.

Comprehensive Analysis of Multiresidue Pesticides from Process Water Obtained from Wastewater Treatment Facilities Using Solid-Phase Microextraction

A novel magnetic blade spray-tandem mass spectrometry (MBS-MS/MS) assay was developed and optimized, and its performance was characterized for the analysis of 204 pesticides from wastewater treatment facility (WWTF) process water. These results were compared and experimentally validated with an untargeted, high-resolution MS (HRMS) approach that employed liquid chromatography (LC)-amenable thin-film microextraction (TFME) devices to further elucidate the fate of pesticides through the WWTF process. As a result of our optimizations, we report an optimized workflow with an extraction time of 10 min, 150 μg of magnetic HLB particles, and 5 s of desorption. Excellent linearity was obtained for 168 of the 204 pesticides in deionized water, where 90% of the quantifiable pesticides had a determination coefficient (R²) of 0.99 across 3 orders of magnitude and 80% had limits of quantification below 0.5 ng/mL. We subsequently applied our optimized MBS-MS/MS method for the analysis of samples collected during the various stages of wastewater treatment from two WWTFs in Southern Ontario. This article presents a new streamlined methodology with a fast turnaround time for analyzing a large panel of pesticides, ultimately providing us the opportunity to evaluate the performance of two WWTFs for their efficacy in removing these toxic chemicals.

Rapid determination of tacrolimus and sirolimus in whole human blood by direct coupling of solid-phase microextraction to mass spectrometry via microfluidic open interface

Immunosuppressive drugs are administered to decrease immune system activity (e.g. of patients undergoing solid organ transplant). Concentrations of immunosuppressive drugs (ISDs) in circulating blood must be closely monitored during the period of immunosuppression therapy due to adverse effects that take place when concentration levels fall outside of the very narrow therapeutic concentration range of these drugs. This study presents the rapid determination of four relevant immunosuppressive drugs (tacrolimus, sirolimus, everolimus, and cyclosporine A) in whole human blood by directly coupling solid-phase microextraction to mass spectrometry via the microfluidic open interface (Bio-SPME-MOI-MS/MS). The BioSPME-MOI-MS/MS method offers ≤ 10% imprecision of in-house prepared quality controls over a 10-day period, ≤ 10% imprecision of ClinCal® Recipe calibrators over a three-day period, and single total turnaround time of ∼ 60 min (4.5 min for high throughput). The limits of quantification were determined to be 0.8 ng mL^-1 for tacrolimus, 0.7 ng mL^-1 sirolimus, 1.0 ng mL^-1 for everolimus, and 0.8 ng mL^-1 for cyclosporine. The limits of detection were determined to be 0.3 ng mL^-1 for tacrolimus, 0.2 ng mL^-1 for sirolimus, 0.3 ng mL^-1 for everolimus, and 0.3 ng mL^-1 for cyclosporine A. The R² values for all analytes were above 0.9992 with linear dynamic range from 1.0 mL^-1 to 50.0 ng mL^-1 for tacrolimus, sirolimus, and everolimus while from 2.5 ng mL^-1 to 500.0 ng mL^-1 for cyclosporine A. To further evaluate the performance of the present method, 95 residual whole blood samples of tacrolimus and sirolimus from patients undergoing immunosuppression therapy were used to compare the Bio-SPME-MOI-MS/MS method against a clinically validated reference method based on chemiluminescent microparticle immunoassay, showing acceptable results. Our results demonstrated that Bio-SPME-MOI-MS/MS can be considered as a suitable alternative to existing methods for the determination of immunosuppressive drugs in whole blood providing faster analysis, better selectivity and sensitivity, and a wider dynamic range than current existing approaches.

MASS SPECTROMETRY ANALYSIS OF DRUGS OF ABUSE: CHALLENGES AND EMERGING STRATEGIES

Mass spectrometry has been the "gold standard" for drugs of abuse (DoA) analysis for many decades because of the selectivity and sensitivity it affords. Recent progress in all aspects of mass spectrometry has seen significant developments in the field of DoA analysis. Mass spectrometry is particularly well suited to address the rapidly proliferating number of very high potency, novel psychoactive substances that are causing an alarming number of fatalities worldwide. This review surveys advancements in the areas of sample preparation, gas and liquid chromatography-mass spectrometry, as well as the rapidly emerging field of ambient ionization mass spectrometry. We have predominantly targeted literature progress over the past ten years and present our outlook for the future. © 2020 Periodicals, Inc. Mass Spec Rev.

Multiresidue pesticide quantitation in multiple fruit matrices via automated coated blade spray and liquid chromatography coupled to triple quadrupole mass spectrometry

Application of ambient mass spectrometry techniques to accelerate analysis of pesticides in produce, with technique validation via chromatographic separation, has not been explored extensively. In this work, coated blade spray (CBS) was used to provide freedom of instrumental choice for a multiresidue panel of pesticides in apple, blueberry, grape, and strawberry through direct-coupling with mass spectrometry (MS) and liquid chromatographic (LC) analyses. For all four matrices, >125 compounds were found to meet European Union guidelines concerning linearity, precision, and accuracy while both CBS-MS/MS and SPME-LC-MS/MS methods achieved limits of quantitation below their minimum regulatory limits. Additionally, results for samples containing residues (n = 57) yielded good agreement between instrumental methods (percent differences < 20% for 73% residues), supporting CBS as a stand-alone technique or complement to LC confirmation of pesticides in fruit matrices.

Emerging trends in paper spray mass spectrometry: Microsampling, storage, direct analysis, and applications

Recent advancements in the sensitivity of chemical instrumentation have led to increased interest in the use of microsamples for translational and biomedical research. Paper substrates are by far the most widely used media for biofluid collection, and mass spectrometry is the preferred method of analysis of the resultant dried blood spot (DBS) samples. Although there have been a variety of review papers published on DBS, there has been no attempt to unify the century old DBS methodology with modern applications utilizing modified paper and paper-based microfluidics for sampling, storage, processing, and analysis. This critical review will discuss how mass spectrometry has expanded the utility of paper substrates from sample collection and storage, to direct complex mixture analysis to on-surface reaction monitoring.

A microfluidic platform integrating paper adsorption-based sample clean-up and voltage-assisted liquid desorption electrospray ionization mass spectrometry for biological sample analysis

Clinical application of direct sampling electrospray ionization mass spectrometry (ESI-MS) remains limited due to problems associated with very "dirty" sample matrices. Herein we report on a microfluidic platform that allows direct mass spectrometric analysis of serum samples of microliter sizes. The platform integrates in-line paper adsorption-based sample clean-up and voltage assisted liquid desorption ESI-MS/MS (VAL DESI-MS/MS) to detect multiple targeted compounds of clinical interest. Adenosine monophosphate (AMP), adenosine diphosphate (ADP), and adenosine triphosphate (ATP) were selected as model analytes. Simultaneous quantification of these compounds in human serum samples was demonstrated. For all the three compounds, linear calibration curves were obtained in a concentration range from 0.20 to 20.0 μmol/L with r² values ≥ 0.996. Limits of detection were 0.019, 0.015, and 0.011 μmol/L for AMP, ADP, and ATP, respectively. Recovery was found in the range from 96.5% to 103.5% at spiking concentrations of 0.25 and 2.50 μmol/L. The results indicate that the proposed microfluidic mass spectrometric platform is robust and effective. It may have a potential in clinical analysis.

Rapid quantification of acetaminophen in plasma using solid-phase microextraction coupled with thermal desorption electrospray ionization mass spectrometry

RATIONALE

Solid-phase microextraction coupled with thermal desorption electrospray ionization tandem mass spectrometry (SPME-TD-ESI-MS/MS) is proposed as a novel method for the rapid quantification of acetaminophen in plasma samples from a pharmacokinetics (PK) study.

METHODS

Traces of acetaminophen were concentrated on commercial fused-silica fibers coated with a polar polyacrylate (PA) polymer using direct immersion SPME. No agitation, heating, addition of salt, or adjustment of the pH of the sample solution was applied during the extraction. Any acetaminophen absorbed on the SPME fibers was subsequently desorbed and detected by TD-ESI-MS/MS.

RESULTS

Parameters of the absorption, sensitivity, reproducibility, and linearity for the SPME-TD-ESI-MS/MS method were evaluated. The time required to complete a TD-ESI-MS/MS analysis was less than 30 seconds. Matrix-matching calibration was performed to calculate the concentration of acetaminophen in the sample. A linear calibration curve with a concentration range of 100-10,000 ng/mL was constructed to calculate the quantity of acetaminophen. The SPME-TD-ESI-MS quantification results for acetaminophen in plasma were in good agreement with those obtained by the conventional LC/MS/MS method.

CONCLUSIONS

With the proposed method, a 10-min SPME time was enough to achieve the lower limit of quantitation (i.e. 100 ng/mL) and for a complete PK profiling of acetaminophen. A shorter extraction time could be achieved by applying agitation, heating, adding salt, or adjusting the pH of the sample solution to enhance analyte absorption efficiency. The time required to detect acetaminophen on the SPME fiber was less than 30 s, allowing the rapid quantification of acetaminophen in plasma with good accuracy.

High-sensitivity detection of therapeutic drugs in complex biofluids using a packed ballpoint-electrospray ionization technique

A simple and sensitive C₁₈ packed ballpoint-electrospray ionization (PBP-ESI) technique was developed for biofluid analysis. In this technique, the configuration of a commercial ballpoint consisting of a hollow chamber, an intermediate socket, and a metal ball was fully exploited. The rear-end hollow chamber was used for loading C₁₈ adsorbent and sample, and the front metal ball served as a spray emitter for online ionization. The good electrical conductivity of the metal body allowed high voltage to be conveniently applied to the ballpoint without inserting the electrode into the solution for electrical connection. Urine sample was directly analyzed with the C₁₈ packed ballpoint; plasma and whole blood samples were premixed with C₁₈ adsorbent before being packed into the ballpoint for detection. As a result of the sample cleanup by C₁₈ adsorbent, the salt matrix in the urine sample as well as the phospholipid and protein matrices in plasma and whole blood samples was significantly reduced. The lower limits of quantitation (LLOQs) for urine, plasma, and whole blood samples reached the subnanogram-per-milliliter level. Graphical abstract.

Metal–Organic Frameworks as Key Materials for Solid-Phase Microextraction Devices—A Review

Metal–organic frameworks (MOFs) have attracted recently considerable attention in analytical sample preparation, particularly when used as novel sorbent materials in solid-phase microextraction (SPME). MOFs are highly ordered porous crystalline structures, full of cavities. They are formed by inorganic centers (metal ion atoms or metal clusters) and organic linkers connected by covalent coordination bonds. Depending on the ratio of such precursors and the synthetic conditions, the characteristics of the resulting MOF vary significantly, thus drifting into a countless number of interesting materials with unique properties. Among astonishing features of MOFs, their high chemical and thermal stability, easy tuneability, simple synthesis, and impressive surface area (which is the highest known), are the most attractive characteristics that makes them outstanding materials in SPME. This review offers an overview on the current state of the use of MOFs in different SPME configurations, in all cases covering extraction devices coated with (or incorporating) MOFs, with particular emphases in their preparation.

Molecularly Imprinted Polymer-Coated Probe Electrospray Ionization Mass Spectrometry Determines Phorbol Esters and Deoxyphorbol Metabolites in Jatropha curcas Leaves

In this study, a molecularly imprinted polymer-coated probe electrospray ionization mass spectrometry (MIPCPESI-MS) method was developed for detection of phorbol esters (PEs) and deoxyphorbol metabolites in Jatropha curcas leaves. Such an approach was established by sticking on a metallic needle a molecularly imprinted polymer to particularly design a MIP-coated probe for selective sampling and ionization of PEs and deoxyphorbol metabolites. By a subsequent application of a high voltage and methanol, as spray solvent, ESI was generated for direct and rapid analysis under ambient and open-air conditions. MIP-coated probe exhibited a high sampling capacity of the PEs and its metabolites in methanolic extracts of J. curcas leaves compared with the non-imprinted polymer (NIP)-coated probe. MIPCPESI-MS allowed the detection of phorbol 12,13-diacetate (PDA) from J. curcas leaves with minimal sample preparation, and with detection limit and quantification reaching 0.28 μg/mL and 0.92 μg/mL, respectively. Also, good linearity was obtained with R² > 0.99 and precision and accuracy values between 4.06-13.49% and - 1.60 to - 15.26%, respectively. The current method was successfully applied to screening methanolic extracts of six different J. curcas leaf genotypes (three toxic and three non-toxic). PDA and three PE deoxyphorbol metabolites were identified only from toxic genotypes, in which PDA was determined with concentration ranging from 222.19 ± 23.55 to 528.23 ± 19.72 μg/g. All these findings support that the MIPCPESI-MS method developed here has a high potential for the analysis of PEs in plant extracts enabling differentiation of toxic and non-toxic genotypes earlier in the leaves.

High-throughput quantification of drugs of abuse in biofluids via 96-solid-phase microextraction-transmission mode and direct analysis in real time mass spectrometry

RATIONALE

The workload of clinical laboratories has been steadily increasing over the last few years. High-throughput (HT) sample processing allows scientists to spend more time undertaking matters of critical thinking rather than laborious sample processing. Herein we introduce a HT 96-solid-phase microextraction (SPME) transmission mode (TM) system coupled to direct analysis in real time (DART) mass spectrometry (MS).

METHODS

Model compounds (opioids) were extracted from urine and plasma samples using a 96-SPME-TM device. A standard voltage and pressure (SVP) DART source was used for all experiments. Examination of SPME-TM performance was done using high-resolution mass spectrometry (HRMS) in full scan mode (100-500 m/z), whereas quantitation of opioids was performed using triple quadrupole MS in multiple reaction monitoring mode and by using a matrix-matched internal standard correction method.

RESULTS

Thirteen points (0.5 to 200 ng mL^-1 ) were used to establish a calibration curve. Low limits of quantitation (LOQ) were obtained (0.5 to 25 ng mL^-1 ) for matrices used. Acceptable accuracy (71.4-129.4%) and repeatability (1.1-24%) were obtained for validation levels tested (0.5, 30 and 90 ng mL^-1 ). In less than 1.5 hours, 96 samples were extracted, desorbed and processed using the 96-SPME-TM system coupled to DART-MS.

CONCLUSIONS

A rapid HT method for detection of opioids in urine and plasma samples was developed. This study demonstrated that ambient ionization mass spectrometry coupled to robust sample preparation methods such as SPME-TM can rapidly and efficiently screen/quantify target analytes in a HT context.

Direct coupling of solid phase microextraction with electrospray ionization mass spectrometry: A Case study for detection of ketamine in urine

Electrospray ionization mass spectrometry (ESI-MS) is a commonly used technique for analysis of various samples. Solid phase microextraction (SPME) is a simple and efficient technique that combines both sampling and sample preparation into one consolidated step, preconcentrating extracted analytes for ultra-sensitive analysis. Historically, SPME has been coupled with chromatography-based techniques for sample separation prior to analysis, however more recently, the chromatographic step has been omitted, with the SPME device directly coupled with the mass spectrometer. In this study, direct coupling of SPME with ESI-MS was developed, and extensively validated to quantitate ketamine from human urine, employing a practical experimental workflow and no extensive hardware modification to the equipment. Among the different fibers evaluated, SPME device coated with C₁₈/benzenesulfonic acid particles was selected for the analysis due to its good selectivity and signal response. Different approaches, including desorption spray, dripping, desorption ESI and nano-ESI were attempted for elution and ionization of the analytes extracted using the SPME fibers. The results showed that the desorption spray and nano-ESI methods offered better signal response and signal duration than the others that were evaluated. The analytical performance of the SPME-nano-ESI-MS setup was excellent, including limit of detection (LOD) of 0.027 ng/mL, limit of quantitation (LOQ) of 0.1 ng/mL, linear range of 0.1-500.0 ng/mL (R² = 0.9995) and recoveries of 90.8-109.4% with RSD 3.4-10.6% for three validation points at 4.0, 40.0 and 400.0 ng/mL, far better than the performance of conventional methods. The results herein presented, demonstrated that the direct coupling of SPME fibers with ESI-MS-based systems allowed for the simple and ultra-sensitive determination of analytes from raw samples such as human urine.

Online Sol-gel Capillary Microextraction-Mass Spectrometry (CME-MS) Analysis of Illicit Drugs

Providing rapid and sensitive sample cleanup, sol-gel capillary microextraction (CME) is a form of solid phase microextraction (SPME). The capillary format of CME couples easily with mass spectrometry (MS) by employing sol-gel sorbent coatings in inexpensive fused silica capillaries. By leveraging the syringe pump and six-port valve readily available on the commercial MS, we can obviate the need for chromatography for samples as complex as urine in quantitative assays. Two different sol-gel materials were studied as microextraction sorbents: one with a single ligand of octadecyl (C₁₈) and the other with a dual-ligand combination of C₁₈ and phenyl (Phe) groups. The CME-MS method was optimized for flow rate and solvent desorption and studied for overall microextraction performance between the two sorbents studied. We extract illicit drugs including cocaine, heroin, amphetamine, methamphetamine, 3,4-methylenedioxymethamphetamine, and oxycodone, proving good run-to-run reproducibility (RSD% < 10%) and low detection limits (< 10 ng mL^-1). The dual-ligand sorbent demonstrated superior performance due to typical hydrophobic properties of C₁₈ as well as potential π-π interactions of the Phe functionality and the aromatic moiety common to many drugs. This study demonstrates the advantage of fine-tuning sol-gel sorbents for application-specific CME-MS. We apply our method to the analysis of various drugs in synthetic and human urine samples and show low carryover effect (~ 5%) and low matrix effect in the presence of the urine matrix. Thus, the sol-gel CME-MS technique described herein stands to be an attractive alternative to other SPME-MS techniques.

A Polymer Coating Transfer Enrichment Method for Direct Mass Spectrometry Analysis of Lipids in Biofluid Samples

A porous polymer coating transfer enrichment method is developed for the direct mass spectrometry (MS) analysis of lipids. The enrichment is fast (ca. 1 min) and enables the profiling and quantitation of lipids in small-volume biofluid samples. Coupled with a photochemical Paternò-Büchi reaction, this method enables the fast determination of lipid structure at the C=C location level and point-of-care lipid biomarker analysis.

Direct sampling mass spectrometry for clinical analysis

Direct sampling mass spectrometry (MS) has been advancing aggressively, showing immense potential in translating MS into the clinical field. Unlike traditional MS analysis involving extensive sample preparation and chromatographic separation, quick and simple procedures with minimal sample pretreatment or purification became available with direct sampling. An overview of the development in this field is provided, including some representative ambient ionization and fast extraction methods. Quantitative applications of these methods are emphasized and their efficacy are highlighted from a clinical aspect; non-quantitative applications in clinical analysis are also discussed. This review also discusses the integration of direct sampling MS with miniature mass spectrometers and its future outlook as an emerging clinical tool for point-of-care analysis.

High-throughput polymer tip-electrospray ionization mass spectrometry for enhanced detection of neopterin and biopterin in clinical urine samples

Urinary biopterin (Bio) and neopterin (Neo) are important markers for clinical diagnosis of hyperphenylalaninemia. Herein, we developed a high-throughput analysis method based on electrospray ionization mass spectrometry (ESI-MS) with polymer tips for the rapid quantitative detection of Bio and Neo in clinical urine samples. Different polymer tips were investigated. It is found that the best detection sensitivity was achieved with hydrophobic polymer tip, ie, polyethylene tips. The high-throughput polymer tip-ESI-MS method allowed a rapid analysis speed at ~40 seconds per sample. The limits of quantification (LOQ) (S/N ≥ 10) for the detection of Bio and Neo were improved to be 5.0 ng/mL. Acceptable relative standard deviation (RSD) values for Neo and Bio were measured to be 12.2% and 13.4% for direct measurement of Bio and Neo in raw urine samples, respectively. Furthermore, Bio and Neo were directly quantified from 18 clinical urine samples by presented method. The ratios of urinary Bio-to-Neo were analyzed for diagnosis of hyperphenylalaninemia. The results demonstrated that the present polymer tip-ESI-MS method is a promising strategy for the rapid analysis of clinical samples.

Fast screening of illicit drugs in beverages and biological fluids by direct coupling of thin film microextraction to dielectric barrier discharge ionization-mass spectrometry

A direct and fast method for quantification of illicit drugs in beverages and biological fluids was developed, using dielectric barrier discharge ionization in combination with high-resolution MS.

Solid phase microextraction coupled to mass spectrometry via a microfluidic open interface for rapid therapeutic drug monitoring

Tranexamic acid (TXA) is an antifibrinolytic used during cardiac surgery that presents high inter-patient variability.