Approach for Downscaling of Electromembrane Extraction as a Lab on-a-Chip Device Followed by Sensitive Red-Green-Blue Detection

Electroextraction of methylene blue from aqueous environmental samples using paper points coupled with hollow fiber membranes

This article introduces a novel approach by coupling paper points with hollow fiber membrane for electroextraction (PP-HF-EE). The method was innovatively applied to extract methylene blue (MB) from large water volumes (up to 580 mL). A comprehensive study of six key parameters - organic filter, acceptor and donor phase composition, extraction time, applied voltage, and sample volume - was conducted using conventional flatbed scanning and digital image analysis. Our results revealed that extraction performance was primarily influenced by time, with low voltages (50 V) and low-conductivity organic filters (1-decanol) yielding comparable results to higher settings (300 V or 1-pentanol). Under optimized conditions (50 V, 60 min, 1-decanol as the organic filter), analytical performance parameters were assessed, demonstrating acceptable precision (RSD <18% for intra- and inter-day measurements) within a linear range of 5-100 μg L-1 (r = 0.98). PP-HF-EE demonstrated reliability through stable and reproducible electric current measurements during all extraction studies. Utilizing an extremely cost-effective detection system, PP-HF-EE achieved detection limits in the low ppb range, highlighting its potential as a promising variation of electromembrane extraction for environmental sample analysis.

Multiphase electroextraction of malachite green from surface water and its determination using digital imaging and chemometric tools

This study introduces a novel method for the quantification of malachite green (MG), a pervasive cationic dye, in surface water by synergizing multiphase electroextraction (MPEE) with digital image analysis (DIA) and partial least square discriminant analysis. Aimed at addressing the limitations of conventional DIA methods in terms of quantitation limits and selectivity, this study achieves a significant breakthrough in the preconcentration of MG using magnesium silicate as a novel sorbent. Demonstrating exceptional processing efficiency, the method allows for the analysis of 10 samples within 20 min, exhibiting remarkable sensitivity and specificity (over 0.95 and 0.90, respectively) across 156 samples in both training and test sets. Notably, the method detects MG at low concentrations (0.2 µg L-1) in complex matrices, highlighting its potential for broader application in environmental monitoring. This approach not only underscores the method's cost-effectiveness and simplicity but also its precision, making it a valuable tool for the preliminary testing of MG in surface waters. This study underscores the synergy among MPEE, DIA, and chemometric tools, presenting a cost-efficient and reliable alternative for the sensitive detection of water contaminants.

Introduction of an electrospun nanofibrous membrane incorporated by metal-organic framework-199 (MOF-199) with Lewis acid property for efficient extraction of sulfonamides in on-chip electromembrane extraction

In this study, a new supporting polymeric membrane having Lewis acid nature was introduced for immobilizing organic solvent in on-chip electromembrane extraction (on-chip EME). For this aim, a polymeric nanofibrous membrane incorporated by a copper based metal-organic framework (MOF-199), with coordinatively unsaturated metal sites and Lewis acid property, was prepared by electrospinning a mixture of polycaprolactone (PCL) and MOF-199. Based on the field emission scanning electron microscopy images, the obtained polymeric membrane consisted of intertwined nanofibers having empty space between the fibers which could provide a suitable place for immobilizing the organic solvent. To demonstrate remarkable extractability of the proposed membrane (PCL/MOF-199 nanofibers) via executing Lewis acid-base interactions, three sulfonamide drugs was selected as anionic polar analytes with Lewis base feature. The parameters affecting the extraction efficiency of the method were optimized through the experimental design method using the orthogonal and rotatable central composite design (CCD). Under optimum conditions, the extraction recoveries ranging from 35.5 to 71.2 %, the relative standard deviations (RSD%) less than 6.45 %, and the detection limits in the range of 0.2-0.5 μg L-1 were achieved. The comparison of the extraction efficiency of the on-chip EME method using the electrospun PCL/MOF-199 nanofibers and PCL nanofibers membranes indicated that the proposed membrane was more efficient for extraction of sulfonamides because of the significant Lewis acid-base interactions of sulfonamides with copper uncoordinated open sites in MOF-199. Finally, the performance of the proposed method for extraction and determination of sulfonamides in three real samples was assayed.

On-chip electromembrane extraction using deep eutectic solvent and red-green-blue analysis by quick-response code readable customized application on a smartphone for measuring salicylic acid in pharmaceutical and plasma samples

The current work presents an on-chip electromembrane extraction (OC-EME) method using deep eutectic solvent followed by QR code-based red-green-blue (RGB) analysis for measuring salicylic acid (SA) in plasma and pharmaceutical samples. The RGB analysis was performed based on forming the SA-Fe3+ complex in the acceptor phase giving a purple solution. The QR code readable customized app provided rapid, easy, and cost-less qualification and quantification of SA with the aid of principal component analysis (PCA). Parameters affecting OC-EME, including the supported liquid membrane (SLM), pH of the donor and acceptor phases, applied voltage, and sample flow rate, were optimized. Also, the concentration of FeCl3, as a chromogenic reagent, and its reaction time with SA were investigated to find the best concentration-dependent signal. Under the optimized conditions, a good relationship was observed between the green intensity and SA concentration within the range of 1.0-100.0 mg l-1 (R2 = 0.9946) in water and 5.0-100.0 mg l-1 (R2 = 0.9902) in plasma. Intra- and inter-day RSDs% were obtained less than 4.7% and 7.7%, respectively. Finally, the method was successfully applied for measuring SA in foot corn treatment, Aspirin medicines, and human plasma, with relative recoveries between 89.0 and 129.2%.

Miniaturized on-chip electromembrane extraction with QR code-based red-green-blue analysis using a customized Android application for copper determination in environmental and food samples

A miniaturized on-chip electromembrane extraction device with QR code-based red-green-blue analysis was designed to determine copper in water, food, and soil. The acceptor droplet consisted of ascorbic acid as the reducing agent and bathocuproine as the chromogenic reagent. The formation of a yellowish-orange complex was a sign of copper in the sample. Then, the qualitative and quantitative analysis of the dried acceptor droplet was done by the customized Android app that was developed based on image analysis concepts. In this application, principal component analysis was performed on the data for the first time to reduce the three dimensions, red, green, and blue, to one dimension. The effective extraction parameters were optimized. The limit of detection and limit of quantification were 0.1 µg mL^-1. Intra- and inter-assay relative standard deviations ranged between 2.0 and 2.3 % and 3.1-3.7 %, respectively. The calibration range was studied between 0.1 and 25 µg mL^-1 (R² = 0.9814).

A new approach of magnetic field application in miniaturized pipette-tip extraction for trace analysis of four synthetic hormones in breast milk samples

Herein, a novel homemade electrical device was designed, including two pieces of external neodymium magnets, providing a reciprocating magnetic field to introduce a magnetic-assisted dispersive pipette-tip micro solid-phase extraction. To evaluate the performance efficiency of the proposed method, a novel magnetic calcined GO/SiO₂@Co-Fe nanocube sorbent was synthesized, filled into the pipette-tip, exposed to the reciprocating magnetic field, and applied for the preconcentration of some hormone therapy drugs in human biological matrices. The effective adsorption and desorption parameters were optimized using a rotatable central composite design and one-variable-at-a-time approaches. Under the optimized conditions, the target analytes' detection limits were found to be below 0.02 ng mL^-1. Moreover, the calibration curves were linear in the range of 0.03-500.00 ng mL^-1 (R² > 0.9966), with RSDs% less than 7.8 %. Eventually, the established method was applied to extract the analytes from breast milk samples, followed by LC-ESI-MS/MS analysis.

Multiphase electroextraction as a simple and fast sample preparation alternative for the digital image determination of doxorubicin in saliva

Monitoring chemotherapeutic drugs in biological fluids is, in many cases, extremely important for dose adjustment, the maintenance of therapies, and the control of side effects. In this work, a method for determining the doxorubicin in saliva by digital image analysis (DIA) was optimised and validated. Images from a paper point were obtained using a conventional and cheap flatbed scanner at a 600 ppp resolution. The RGB data channels were obtained from the images in a region of 15 × 15 pixels around the sorbent vertex. The paper point was used as sorbent material in sample preparation using a multiphase electroextraction system. Following optimisation using a Doehlert experimental design, the method was able to simultaneously extract 66 samples in 20 min. The high selectivity of the electric field associated with the sorption capacity of the cellulosic material allowed the chemotherapy drug to be pre-concentrated and quantified in a range between 50 and 500 μg L^-1 (R² > 0.98). The method also exhibited adequate parameters (limits of detection and quantification, recovery, and precision) indicating its potential application in the monitoring of doxorubicin and similar drugs in saliva.

A new microfluidic-chip device followed by sensitive image analysis of smart phone for simultaneous determination of dyes with different acidic-basic properties

In this study, a new microfluidic-chip coupled with micro solid phase extraction (μ-SPE) and a RGB detection system was designed. The method was used for extraction and simultaneous determination of trace amounts of dyes with different acidic-basic properties. Erythrosine (Ery) and Crystal Violet (CV) were selected as acidic and basic model analytes, respectively. The first step of this method is based on the on-chip electromembrane extraction (CEME) of analytes from aqueous solution. The utilized microfluidic system is a single compartment that composed of three polymethyl metacrylate plates (with sandwiched structures) patterned with palm shaped helix channels. The device consisted one pair of platinum electrodes that were embedded in the acceptor phase channels in each side. The middle part was cut and used as the path of the sample. The extracted analytes by CEME were passed through the micro-packed column containing strong cation and anion exchanger sorbents respectively. Two adsorbents were separated by a polypropylene frit and sealed on each side by two polypropylene frites. Following dye adsorption on the sorbents, the colors that emerged were promptly evaluated using RGB colorimetry on a smartphone. Central composite design was used to analyze and optimize the effective parameters on extraction efficiency. The relative standard deviations (RSDs%) based on five replicate measurements were less than 7.8% for RGB and 8.6% for the spectrophotometry technique under ideal conditions. Image analysis using a smartphone yielded LOD values of 15.0 and 10.5 μg L^-1 for Ery and CV, respectively. The CEME- μ-SPE -RGB approach produced findings that were equivalent to those obtained by spectrophotometry. Finally, the approach was used to accurately determine Ery and CV in water samples, yielding good relative recoveries (recovery ≥94.0).

In-tube gel electromembrane extraction: A green strategy for the extraction of narcotic drugs from biological samples

The development of green and miniature extraction methods is always a major and controversial challenge in the field of sample preparation. In this work, in-tube gel electromembrane extraction (IT-G-EME) was developed as a miniaturized extraction device for the extraction of six narcotic drugs (codeine, oxycodone, hydrocodone, tramadol, thebaine, and noscapine) from biological samples. A transparent capillary tube (∼6 cm) was used as a microextraction unit. The middle part of the tube was filled with a narrow plug (∼3 mm) of the agarose gel (3.0% w/v) as a membrane and the other sides were filled with aqueous extractant solution (pH 2.0, 20 µL) and sample solution (pH 5.0, 200 µL). By applying electrical potential (400 V), the target drugs with positive charge were migrated from sample solution toward the extractant solution through gel membrane during short extraction time (5 min). Then, the enriched analytes in extractant solution was analyzed by HPLC-UV. Under the optimized conditions, the calibration curves were linear within the permissible range of 10.0-1500 ng/mL (r² ≥ 0.991). Limits of detection and extraction recoveries were in the range of 3.0-4.5 ng/mL and 61.9-86.9%, respectively. On the basis of four replications, the repeatability of the method was also evaluated in terms of intra- and inter-day RSDs (%), which did not exceed from 6.6 and 7.9%, respectively in aqueous media. The figures of merit were also assessed in biological samples. Eventually, the developed method was profitably used for simultaneous determination of narcotic drugs in the real urine and plasma samples.

Carrasco-Correa E, Varanasupakul P, Kubáň P, Miró M. Programmable Millifluidic Platform Integrating Automatic Electromembrane Extraction Cleanup and In-Line Electrochemical Detection: A Proof of Concept

A fully automatic millifluidic sensing platform coupling in-line nonsupported microelectromembrane extraction (μ-EME) with electrochemical detection (ECD) is herein proposed for the first time. Exploiting the features of the second generation of flow analysis, termed sequential injection (SI), the smart integration of SI and μ-EME-ECD enables (i) the repeatable formation of microvolumes of phases for the extraction step in a membrane-less (nonsupported) arrangement, (ii) diverting the acceptor plug to the ECD sensing device, (iii) in-line pH adjustment before the detection step, and (iv) washing of the platform for efficient removal of remnants of wetting film solvent, all entirely unsupervised. The real-life applicability of the miniaturized sensing system is studied for in-line sample cleanup and ECD of diclofenac as a model analyte after μ-EME of urine as a complex biological sample. A comprehensive study of the merits and the limitations of μ-EME solvents on ECD is presented. Under the optimal experimental conditions using 14 μL of unprocessed urine as the donor, 14 μL of 1-nonanol as the organic phase, and 14 μL of 25 mM NaOH as the acceptor in a 2.4 mm ID PTFE tubing, an extraction voltage of 250 V, and an extraction time of 10 min, an absolute (mass) extraction recovery of 48% of diclofenac in urine is obtained. The proposed flow-through system is proven to efficiently remove the interfering effect of predominantly occurring organic species in human urine on ECD with RSD% less than 8.6%.

Effect of sample matrices on supported liquid membrane: Efficient electromembrane extraction of cathinones from biological samples

In this work, the effect of sample matrix on electromembrane extraction (EME) was investigated for the first time using cathinones (log P < 1.0) as polar basic model analytes. Ten supported liquid membranes (SLMs) were tested for EME from spiked buffer solutions, urine, and whole blood samples, respectively. For buffer solutions, SLMs containing aromatic solvents provided higher EME recovery than non-aromatic solvents, which confirmed the significance of cation-π interactions for EME of basic substances. Interestingly, when applied to urine and whole blood samples, aromatic SLMs were less efficient, while non-aromatic SLMs containing abundant hydrogen-bond acidity/basicity were efficient. These observations were explained by SLM fouling, and the antifouling property of the SLM was clearly dependent on the nature of the SLM solvent. Accordingly, a binary SLM containing aromatic 1-ethyl-2-nitrobenzene (ENB) and non-aromatic 1-undecanol (1:1 v/v) was developed. This binary SLM was not prone to fouling, and provided high recoveries of cathinones from urine and whole blood. EME based on this SLM was optimized and evaluated in combination with liquid chromatography tandem mass spectrometry (LC-MS/MS), and the linear ranges with R² ≥ 0.9903 for cathinones in whole blood and urine were 5-200 ng/mL and 1-200 ng/mL, respectively. The LOD and LOQ of cathinones were ranged from 0.12 to 0.54 ng/mL and 0.38-1.78 ng/mL, respectively. The repeatability and accuracy bias at three levels were ≤11% and within 10%, respectively. In addition, the matrix effect ranged from 88% to 118% was also in compliance with guidelines for bioanalytical method validation provided by the European Medicines Agency.

Electrocolorimetric gel-based sensing approach for simultaneous extraction, preconcentration, and detection of iodide and chromium (VI) ions

A total integrated electrocolorimetric sensing approach consisting of gel-based electromembrane extraction and colorimetric detection in a one-step process was developed. This system was designed using colorimetric reagents preadded to the agarose gel for the determination of the following two model analytes: iodide and hexavalent chromium [Cr(VI)]. In this system, when a voltage was applied, the analytes were extracted and transferred from the sample solution (donor phase) to the gel (acceptor phase). The analytes then simultaneously reacted with the colorimetric reagents inside the gel, yielding blue and violet colors for iodide and Cr(VI), respectively. These colors were then analyzed using a portable spectrometer and could also be distinguished with the naked eye. Parameters affecting the extraction efficiency were studied and optimized for both analytes. The gel composition for iodide detection was 4% (w/v) agarose, 5% (v/v) H₂O₂, and 1% (w/v) starch in 2 mM HCl. The gel composition for Cr(VI) detection was 2% (w/v) agarose and 1% (w/v) DPC in 0.5 mM HNO₃. Both analytes were extracted at an applied potential of 50 V, an extraction time of 15 min and a stirring rate of 600 rpm. Under the optimized conditions, the developed systems provided linear responses within 15 min for iodide concentrations ranging from 50 to 250 μg L^-1 with a detection limit of 18 μg L^-1 and for Cr(VI) concentrations ranging from 30 to 125 μg L^-1 with a detection limit of 5 μg L^-1. Finally, these systems were successfully applied to the determination of iodide in iodide food supplement samples and Cr(VI) in drinking water samples, showing a negligible matrix effect. This integration could also be extended to other analytes and detection systems to develop sensitive, on-site, and environmentally friendly sensing approaches.

Electromembrane extraction in microfluidic formats

Electromembrane extraction is a microextraction technique where charged analytes are extracted across a supported liquid membrane and selectively isolated from the sample based on an electrical field. Since the introduction in 2006, there has been continuously increasing interest in electromembrane extraction, and currently close to 50 new articles are published per year. Electromembrane extraction can be performed in different technical configurations, based on standard laboratory glass vials or 96-well plate systems, and applications are typically related to pharmaceutical, environmental, and food and beverages analysis. In addition to this, conceptual research has developed electromembrane extraction into different milli- and microfluidic formats. These are much more early-stage activities, but applications among others related to organ-on-chip systems and smartphone detection indicate unique perspectives. To stimulate more research in this direction, the current article reviews the scientific literature on electromembrane extraction in milli- and microfluidic formats. About 20 original research articles have been published on this subject so far, and these are discussed critically in the following. Based on this and the authors own experiences with the topic, we discuss perspectives, challenges, and future research.

An efficient microfluidic device based on electromembrane extraction for the simultaneous extraction of acidic and basic drugs

The simultaneous extraction of acidic and basic compounds is considered a great challenge. In this work, an efficient and fast microfluidic device is described for the simultaneous determination of acidic and basic drugs by two electromembrane extraction, offering extraction efficiencies over 98% for all analytes in human urine samples and solving the difficulties encountered to date. The sample is submitted into the device and the collected acceptor phase is directly analyzed by diode array detector and high-pressure liquid chromatography (HPLC). The device consisted of three poly(methylmethacrylate) layers and four electrodes to perform EME in two steps in a single device. Two acidic analytes (ketoprofen and naproxen) and two basic analytes (amitriptyline and loperamide) were selected as model analytes. The device proposed works under stable electric field conditions, low current intensities that confers great stability to the supported liquid membrane. After a comprehensive study of the SLM, 1:1 2-nitrophenyl octhyl ether:dodecanol was selected as optimal. This device has also been successfully applied in 1:2 diluted bovine plasma samples with recoveries over 84% and a relative standard deviation below 6%. This microfluidic device needs small sample volumes (lower than 50 μL) and offers short extraction times (10 min) and excellent clean-up. Furthermore, it has proven to be a robust and reproducible device after more than 30 consecutive extractions, and thanks to the low potential required (5 V), it allows its compatibility with a single battery.

Green microfluidic liquid-phase microextraction of polar and non-polar acids from urine

In this work, hippuric acid (log P = 0.5), anthranilic acid (log P = 1.3), ketoprofen (log P = 3.6), and naproxen (log P = 3.0) were simultaneously extracted by a green microfluidic device based on the principles of liquid-phase microextraction (LPME). Different deep eutectic solvents (DESs) were investigated as supported liquid membrane (SLM), and a mixture of camphor and menthol as eutectic solvents in the molar ratio 1:1 was found to be highly efficient for the simultaneous extraction of non-polar and polar acidic drugs. LPME was conducted for 6 min per sample. Urine sample was delivered to the system at 1 μL min^-1, and target analytes were extracted exhaustively (75-100% recovery) across the DES SLM, and into pure aqueous phosphate buffer pH 11.0 delivered as acceptor at 1 μL min^-1. The acceptor was analyzed with liquid chromatography-UV detection. Interestingly, the DES enabled extraction of both the polar and non-polar model analytes at the same time; all chemicals were green and non-hazardous, and the chemical waste was less than 1 mg per sample.

Recent applications of microextraction sample preparation techniques in biological samples analysis

Analysis of biological samples is affected by interfering substances with chemical properties similar to those of the target analytes, such as drugs. Biological samples such as whole blood, plasma, serum, urine and saliva must be properly processed for separation, purification, enrichment and chemical modification to meet the requirements of the analytical instruments. This causes the sample preparation stage to be of undeniable importance in the analysis of such samples through methods such as microextraction techniques. The scope of this review will cover a comprehensive summary of available literature data on microextraction techniques playing a key role for analytical purposes, methods of their implementation in common biological samples, and finally, the most recent examples of application of microextraction techniques in preconcentration of analytes from urine, blood and saliva samples. The objectives and merits of each microextration technique are carefully described in detail with respect to the nature of the biological samples. This review presents the most recent and innovative work published on microextraction application in common biological samples, mostly focused on original studies reported from 2017 to date. The main sections of this review comprise an introduction to the microextraction techniques supported by recent application studies involving quantitative and qualitative results and summaries of the most significant, recently published applications of microextracion methods in biological samples. This article considers recent applications of several microextraction techniques in the field of sample preparation for biological samples including urine, blood and saliva, with consideration for extraction techniques, sample preparation and instrumental detection systems.

Microfluidic-enabled versatile hyphenation of electromembrane extraction and thin film solid phase microextraction

In the present study, a versatile combination of electromembrane extraction (EME) with thin film solid phase microextraction (TF-SPME) was introduced using a microfluidic chip device. The device consisted of two single channels on two separate layers. The upper channel was dedicated to donor phase flow pass, while the beneath channel was used as a reservoir for stagnant acceptor solution. A slide of fluorine doped tin oxide (FTO) was accommodated in the bottom of the acceptor phase channel. A thin layer of polyaniline was electrodeposited on the FTO surface to achieve the required thin film for TF-SPME. A stainless-steel wire was embedded in the donor phase channel and another wire was also attached to the FTO surface. The channels were separated by a piece of polypropylene membrane impregnated with 1-octanol and the whole chip was fixed with bolts and nuts. The driving force for the extraction was an 8 V direct current (DC) voltage applied across the supported liquid membrane (SLM). Under the influence of the electrical field, analytes immigrated from sample towards the acceptor phase and then adsorbed on the thin film of the solid phase. Finally, the analytes were desorbed by successive movement of a desorption solvent in the acceptor phase channel followed by injection of the desorption solution to HPLC-UV. The applicability of the proposed device was demonstrated by the determination of four synthetic food dyes: Amaranth, Ponceau 4R, Allura Red, and Carmoisine, as the model analytes. The effective parameters on the efficiency of the both EME and TF-SPME were investigated. Under the optimized conditions, the microchip provided low LODs (1-10 μg L^-1), and a wide linear dynamic range of 10-1000 μg L^-1 for all analytes. The system also offered RSD values lower than 5.5% and acceptable reusability of the thin film for multiple extractions.

Engineering strategies for enhancing the performance of electrochemical paper-based analytical devices

Applications of electrochemical detection methods in microfluidic paper-based analytical devices (μPADs) has revolutionized the area of point-of-care (POC) testing towards highly sensitive and selective quantification of various (bio)chemical analytes in a miniaturized, low-coat, rapid, and user-friendly manner. Shortly after the initiation, these relatively new modulations of μPADs, named as electrochemical paper-based analytical devices (ePADs), gained widespread popularity within the POC research community thanks to the inherent advantages of both electrochemical sensing and usage of paper as a suitable substrate for POC testing platforms. Even though general aspects of ePADs such as applications and fabrication techniques, have already been reviewed multiple times in the literature, herein, we intend to provide a critical engineering insight into the area of ePADs by focusing particularly on the practical strategies utilized to enhance their analytical performance (i.e. sensitivity), while maintaining the desired simplicity and efficiency intact. Basically, the discussed strategies are driven by considering the parameters potentially affecting the generated electrochemical signal in the ePADs. Some of these parameters include the type of filter paper, electrode fabrication methods, electrode materials, fluid flow patterns, etc. Besides, the limitations and challenges associated with the development of ePADs are discussed, and further insights and directions for future research in this field are proposed.

A Comprehensive Review on Developed Pharmaceutical Analysis Methods by Iranian Analysts in 2018

This article summarizes the publishing activities including bioanalytical and pharmaceutical analyses researches carried out in Iran in 2018 in order to connect academic researchers to those in industry, medical care units and hospitals. A wide spectrum of analytical methods has been used to determine and/or evaluate drug levels in the biological samples, based on physical, chemical and biochemical principles. We have compiled a concise survey of the literature covering 125 reports and tabulated the relevant analytical parameters. Chromatographic and electrochemical methods were found to be the technique of choice for many workers and almost 83% studies were performed by using these methods. This is the first annual review of the literature searching in SCOPUS database for published bioanalytical and pharmaceutical analysis researches in Iran.

A New Portable Colorimetric Sensor Based on RGB Chromaticity for Quantitative Determination of Sarin in Water

Background:

Sarin is a nerve agent which is lethal to people due to its high toxicity. According to its extreme toxicity, sarin, relatively lack of color, highly toxic, miscible in water, poses viable threats to potable water sources. Therefore, there is an urgent need for portable, rapid and yet reliable methods to monitor for adulteration of potable water sources by sarin on spot.

Methods:

A stock solution of 30 mg/L sarin was prepared daily by dissolving 300 μg of sarin in 10 mL isopropanol. A certain amount of sarin was added to the glass tube, and then o-dianisidine and hydrogen peroxide were added. The pH value of the solution was adjusted to 9.8. The solution was transferred to the test tube after 10 minutes. A test tube of 2 mL was placed between the light source and the RGB color sensor. The LED light source illuminates directly over the test tube while the RGB sensor obtained the generated spectral response. This RGB voltage output is connected to the ADC and microcontroller to convert these analog voltages to three digital data. This RGB digital data is linked to the microcomputer through the serial port that is interfaced with the user interface. The data thus obtained in the sensor can be processed to display the sarin concentration.

Results:

Under the optimum conditions as described above, the calibration curve of chromaticity value versus sarin concentration was linear in the range of 0.15 mg/L to 7.8 mg/L. According to the IUPAC definition, theoretical detection limits of this method were 0.147 mg/L and 0.140 mg/L for R and B values, respectively. The practical detection limit was 0.15 mg/L. The sensor was successfully applied to the determination of sarin in artificial water samples and the recoveries were between 86.0% to 95.9%.

Conclusion:

The results in the present work have demonstrated the feasibility to design a new portable colorimetric sensor based on the RGB chromaticity method for quantitative determination of sarin in water. The influences of chromogenic reagent, oxidant, reaction time, o-dianisidine concentration, hydrogen peroxide concentration, reaction temperature, pH on the chromaticity values were investigated. The results showed that the sensor possessed high selectivity, sensitivity and good repeatability. The method would be potentially applied to the analysis of other toxic compounds in environment, such as other chemical warfare agents.

Impact of ion balance in electromembrane extraction

Electromembrane extraction (EME) involves transfer of analyte ions from aqueous sample, through a supported liquid membrane (SLM), and into an aqueous acceptor solution under the influence of an external electrical field. In addition to target analyte ions, the sample also contains matrix ions, and both the sample and acceptor contains background buffer ions to control pH. The ratio between the total amount of ions in sample and acceptor defines the ion balance (χ). Previous publications have discussed the impact of ion balance, but conclusions are contradictory. Therefore, the current paper investigated the ion balance in more detail. From a theoretical point of view, low χ-values favor EME; buffer anions at high concentration in the acceptor migrate into the SLM, while target cations enters the SLM from the sample to maintain electroneutrality. A large number of experiments was performed in this paper to investigate the practical impact of ion balance. Twelve basic drugs were used as model analytes (0.0 < log P < 5.0), and 2-nitrophenyl octyl ether (NPOE) and NPOE + 5% di(2-ethylhexyl) phosphate (DEHP) were used as SLM. With formate buffer pH 3.75 as sample and acceptor, the impact of χ in the range 0.01-10 was studied without bias from differences in pH. Here model analytes were unaffected by ion balance. Buffers containing propionic, butyric, and valeric acid were also tested. These buffer ions migrated more into the SLM, and affected recoveries in several cases. However, this was due to ion pairing rather than effects of ion balance. Similar behaviors from sodium chloride and urine samples were observed with different χ-values. Thus, in the systems tested, almost no impact of ion balance was found, and this was attributed to very low partition of background buffer and matrix ions into the SLM. On the other hand, extractions were in several cases influenced by ion pairing phenomena.

Electrochemically Modulated Liquid-Liquid Extraction for Sample Enrichment

A new sample preparation method is proposed for the extraction of pharmaceutical compounds (Metformin, Phenyl biguanide, and Phenformin) of varied hydrophilicity, dissolved in an aqueous sample. When in contact with an organic phase, an interfacial potential is imposed by the presence of an ion, tetramethylammonium (TMA⁺), common to each phase. The interfacial potential difference drives the transfer of ionic analytes across the interface and allows it to reach up to nearly 100% extraction efficiency and a 60-fold enrichment factor in optimized extraction conditions as determined by HPLC analysis.

Electromembrane extraction with solvent modification of the acceptor solution: improved mass transfer of drugs of abuse from human plasma

Aim: Electromembrane extraction (EME) of 37 drugs of abuse with significant differences in terms of polarity (0.68 < log P < 4.3) and basicity (1.17 < pKa < 10.38) was investigated from human plasma. Materials & methods: EME was performed with 250 mM trifluoroacetic acid and DMSO (1:1 v/v) in the acceptor solution. Results & conclusion: The analytes were extracted efficiently with pure 2-nitrophenyloctyl ether as supported liquid membrane when the acceptor solution was modified with DMSO. Thus, using DMSO mixed with 250 mM trifluoroacetic acid (1:1, v/v) as acceptor solution, recoveries from 40 to 105% (relative standard deviation <20%) were obtained for 33 of the analytes under optimized conditions. EME followed by ultra-HPLC–MS/MS analysis was evaluated from human plasma, and the results were satisfactory.

Simultaneous extraction of acidic and basic drugs via on-chip electromembrane extraction using a single-compartment microfluidic device

A chip was designed for simultaneous extraction of acidic and basic drugs from biological fluids.

A new microfluidic-chip device for selective and simultaneous extraction of drugs with various properties

In the present study, a newly designed microfluidic-chip device was used for the selective and simultaneous electromembrane extraction (EME) of drugs with different properties.