Ultrasensitive Electrochemical DNA Biosensor Based on a Label-Free Assembling Strategy Using a Triblock polyA DNA Probe

Triblock polyadenine-based electrochemical aptasensor for ultra-sensitive detection of carcinoembryonic antigen via exonuclease III-assisted target recycling and hybridization chain reaction

Carcinoembryonic antigen (CEA), a key colon biomarker, demands a precise detection method for cancer diagnosis and prognosis. This study introduces a novel electrochemical aptasensor using a triblock polyadenine probe for ultra-sensitive detection of CEA. The method leverages Exonuclease III (Exo III)-assisted target recycling and hybridization chain reaction. The triblock polyadenine probe self-assembles on the bare gold electrode through the strong affinity between adenine and gold electrode, blocking CEA diffusion and providing a large immobilization surface. CEA binding to hairpin probe 1 (HP1), followed by the hybridization between HP1 and hairpin probe 2 (HP2), triggers DNA cleavage by Exo III, amplifying the signal via a hybridization chain reaction and producing numerous dsDNA walkers that generates a dramatic electrochemical impedance signal. Under optimized conditions, the aptasensor achieved two ultra-low detection limits: 0.39 ag∙mL-1 within the concentration range of 5 ag∙mL-1 to 5 × 106 ag∙mL-1, and 1.5 ag∙mL-1 within the concentration range of 5 × 106 ag∙mL-1 to 1 × 1010 ag∙mL-1. Its performance in human serum samples meets the practical standards, offering a promising new tool for ultrasensitive tumor marker detection, potentially revolutionizing early cancer diagnosis.

A novel biosensing strategy on the dynamic and on-site detection of Vibrio coralliilyticus eDNA for coral health warnings

Heat stress and coral diseases are the predominant factors causing the degradation of coral reef ecosystems. Over recent years, Vibrio coralliilyticus was identified as a temperature-dependent pathogen causing tissue lysis in Pocillopora damicornis and one of the primary pathogens causing bleaching and mortality in other corals. Yet current detection techniques for V. coralliilyticus rely primarily on qPCR and ddPCR, which cannot meet the requirements for non-invasive and real-time detection. Herein, we developed an effective electrochemical biosensor modified by an Au-MoS2/rGO (AMG) nanocomposites and a specific capture probe to dynamically detect V. coralliilyticus environment DNA (eDNA) in aquarium experiments, with a lower limit of detection (0.28 fM) for synthetic DNA and a lower limit of quantification (9.8 fg/µL, ∼0.86 copies/µL) for genomic DNA. Its reliability and accuracy were verified by comparison with the ddPCR method (P > 0.05). Notably, coral tissue started to lyse at only 29 °C when the concentration of V. coralliilyticus increased abruptly to 880 copies/µL, indicating the biosensor could reflect the types of pathogen and health risks of corals under heat stress. Overall, the novel and reliable electrochemical biosensing technology provides an efficient strategy for the on-site monitoring and early warning of coral health in the context of global warming.

A multi-channel electrochemical biosensor based on polyadenine tetrahedra for the detection of multiple drug resistance genes

Antimicrobial resistance poses a serious threat to human health due to the high morbidity and mortality caused by drug-resistant microbial infections. Therefore, the development of rapid, sensitive and selective identification methods is key to improving the survival rate of patients. In this paper, a sandwich-type electrochemical DNA biosensor based on a polyadenine-DNA tetrahedron probe was constructed. The key experimental conditions were optimized, including the length of polyadenine, the concentration of the polyadenine DNA tetrahedron, the concentration of the signal probe and the hybridization time. At the same time, poly-avidin-HRP80 was used to enhance the electrochemical detection signal. Finally, excellent biosensor performance was achieved, and the detection limit for the synthetic DNA target was as low as 1 fM. In addition, we verified the practicability of the system by analyzing E. coli with the MCR-1 plasmid and realized multi-channel detection of the drug resistance genes MCR-1, blaNDM, blaKPC and blaOXA. With the ideal electrochemical interface, the polyA-based biosensor exhibits excellent stability, which provides powerful technical support for the rapid detection of antibiotic-resistant strains in the field.

Triblock PolyA-Mediated Protein Biosensor Based on a Size-Matching Proximity Hybridization Analysis

The antibodies in the natural biological world utilize bivalency/multivalency to achieve a higher affinity for antigen capture. However, mimicking this mechanism on the electrochemical sensing interface and enhancing biological affinity through precise spatial arrangement of bivalent aptamer probes still pose a challenge. In this study, we have developed a novel self-assembly layer (SAM) incorporating triblock polyA DNA to enable accurate organization of the aptamer probes on the interface, constructing a "lock-and-key-like" proximity hybridization assay (PHA) biosensor. The polyA fragment acts as an anchoring block with a strong affinity for the gold surface. Importantly, it connects the two DNA probes, facilitating one-to-one spatial proximity and enabling a controllable surface arrangement. By precisely adjusting the length of the polyA fragment, we can tailor the distance between the probes to match the molecular dimensions of the target protein. This design effectively enhances the affinity of the aptamers. Notably, our biosensor demonstrates exceptional specificity and sensitivity in detecting PDGF-BB, as confirmed through successful validation using human serum samples. Overall, our biosensor presents a novel and versatile interface for proximity assays, offering a significantly improved surface arrangement and detection performance.

Development of Optical Differential Sensing Based on Nanomaterials for Biological Analysis

The discrimination and recognition of biological targets, such as proteins, cells, and bacteria, are of utmost importance in various fields of biological research and production. These include areas like biological medicine, clinical diagnosis, and microbiology analysis. In order to efficiently and cost-effectively identify a specific target from a wide range of possibilities, researchers have developed a technique called differential sensing. Unlike traditional "lock-and-key" sensors that rely on specific interactions between receptors and analytes, differential sensing makes use of cross-reactive receptors. These sensors offer less specificity but can cross-react with a wide range of analytes to produce a large amount of data. Many pattern recognition strategies have been developed and have shown promising results in identifying complex analytes. To create advanced sensor arrays for higher analysis efficiency and larger recognizing range, various nanomaterials have been utilized as sensing probes. These nanomaterials possess distinct molecular affinities, optical/electrical properties, and biological compatibility, and are conveniently functionalized. In this review, our focus is on recently reported optical sensor arrays that utilize nanomaterials to discriminate bioanalytes, including proteins, cells, and bacteria.

Poly-adenine-mediated tetrahedral DNA nanostructure with multiple target-recognition sites for ultrasensitive and rapid electrochemical detection of Aflatoxin B1

Tetrahedral DNA nanostructures (TDNs) are widely used in the development of electrochemical biosensors due to their structural stability, programmability, and strong interfacial orderliness. However, the complex modifications on the electrode and the single vertex target recognition of the TDNs limit their applications in electrochemical biosensing. Herein, we developed a universal detection system based on a novel polyadenine-based tetrahedral DNA nanostructure (ATDN) using Aflatoxin B1 (AFB1) as the model target for analysis. In the absence of target AFB1, the signal probes (SP) modified with ferrocene would be anchored by five aptamers on ATDN. The target capture by aptamers led to a release of SP from the electrode surface, resulting in a significant reduction of the electrochemical signal. This new nanostructure was not only dispensed with multi-step electrode modifications and strong mechanical rigidity but also had five modification sites which enhanced the detection sensitivity for the target. As a result, this biosensor shows good analytical performance in the linear range of 1 fg mL-1 to 1 ng mL-1, exhibiting a low detection limit of 0.33 fg mL-1. Satisfactory accuracy has also been demonstrated through good recoveries (95.2%-98.9%). The proposed new tetrahedral DNA nanostructure can provide a more rapid and sensitive alternative to previous electrochemical sensors based on the conventional TDN. Since DNA sequences can be designed flexibly, the sensing platform in this strategy can be extended to detect various targets in different fields.

Electrochemical Affinity Biosensors: Pervasive Devices with Exciting Alliances and Horizons Ahead

Electrochemical affinity biosensors are evolving at breakneck speed, strengthening and colonizing more and more niches and drawing unimaginable roadmaps that increasingly make them protagonists of our daily lives. They achieve this by combining their intrinsic attributes with those acquired by leveraging the significant advances that occurred in (nano)materials technology, bio(nano)materials and nature-inspired receptors, gene editing and amplification technologies, and signal detection and processing techniques. The aim of this Perspective is to provide, with the support of recent representative and illustrative literature, an updated and critical view of the repertoire of opportunities, innovations, and applications offered by electrochemical affinity biosensors fueled by the key alliances indicated. In addition, the imminent challenges that these biodevices must face and the new directions in which they are envisioned as key players are discussed.

Electrochemical aptamer biosensor for DNA detection based on label-free aptamers

Electrochemical aptasensor has been broadly advanced for nucleic acid detection. However, it is a long-term goal to design an aptasensor with high specificity, flexibility, and simplicity. In this work, we develop a strategy of triblock DNA probe, which consists of two DNA probes at both ends and ployA fragments in the middle as probe-polyA-probe. PolyA fragment has high affinity to the surface of gold electrode, so it can be assembled on the electrode surface via polyA instead of traditional Au-S bonds. When the target DNA is simultaneously hybridized with the two capture probes, the hybridization stability can be improved due to the strong base stacking effect. [Ru(NH₃)₆]³⁺, as signal probe, can be electrostatically adsorbed on the negatively charged DNA skeleton. A wide linear range (10 pM-10 μM) is obtained with a detection limit of 2.9 pM. Our electrochemical aptasensor has good repeatability, stability, and specificity. More importantly, the electrochemical sensor can successfully detect DNA in human serum samples, which proves its practical value and extensive applicability in complex environment.

A label-free electrochemical DNA biosensor used a printed circuit board gold electrode (PCBGE) to detect SARS-CoV-2 without amplification

The emergence of coronavirus disease 2019 (COVID-19) motivates continuous efforts to develop robust and accurate diagnostic tests to detect severe acute respiratory syndrome coronavirus-2 (SARS-CoV-2). Detection of viral nucleic acids provides the highest sensitivity and selectivity for diagnosing early and asymptomatic infection because the human immune system may not be active at this stage. Therefore, this work aims to develop a label-free electrochemical DNA biosensor for SARS-CoV-2 detection using a printed circuit board-based gold substrate (PCBGE). The developed sensor used the nucleocapsid phosphoprotein (N) gene as a biomarker. The DNA sensor-based PCBGE was fabricated by self-assembling a thiolated single-stranded DNA (ssDNA) probe onto an Au surface, which performed as the working electrode (WE). The Au surface was then treated with 6-mercapto-1-hexanol (MCH) before detecting the target N gene to produce a well-oriented arrangement of the immobilized ssDNA chains. The successful fabrication of the biosensor was characterized using cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and atomic force microscopy (AFM). The DNA biosensor performances were evaluated using a synthetic SARS-CoV-2 genome and 20 clinical RNA samples from healthy and infected individuals through EIS. The developed DNA biosensor can detect as low as 1 copy per μL of the N gene within 5 minutes with a LOD of 0.50 μM. Interestingly, the proposed DNA sensor could distinguish the expression of SARS-CoV-2 RNA in a patient diagnosed with COVID-19 without any amplification technique. We believe that the proposed DNA sensor platform is a promising point-of-care (POC) device for COVID-19 viral infection since it offers a rapid detection time with a simple design and workflow detection system, as well as an affordable diagnostic assay.

Interfacial DNA Framework-Enhanced Background-to-Signal Transition for Ultrasensitive and Specific Micro-RNA Detection

Interfacial DNA self-assembly is fundamental to solid nucleic acid biosensors, whereas how to improve the signal-to-noise ratio has always been a challenge, especially in the charge-based electrochemical DNA sensors because of the large noise from the negatively charged DNA capture probes. Here, we report a DNA framework-reversed signal-gain strategy through background-to-signal transition for ultrasensitive and highly specific electrical detection of microRNAs (miRNAs) in blood. By using a model of enzyme-catalyzed deposition of conductive molecules (polyaniline) targeting to DNA, we observed the highest signal contribution per unit area by the highly charged three-dimensional (3D) tetrahedral DNA framework probe, relative to the modest of two-dimensional (2D) polyA probe and the lowest of one-dimensional (1D) single-stranded (ss)DNA probe, suggesting the positive correlation of background DNA charge with signal enhancement. Using such an effective signal-transition design, the DNA framework-based electrochemical sensor achieves ultrasensitive miRNAs detection with sensitivity up to 0.29 fM (at least 10-fold higher than that with 1D ssDNA or 2D polyA probes) and high specificity with single-base resolution. More importantly, this high-performance sensor allows for a generalized sandwich detection of tumor-associated miRNAs in the complex matrices (multiple cell lysates and blood serum) and further distinguishes the tumor patients (e.g., breast, lung, and liver cancer) from the normal individuals. These advantages signify the promise of this miRNA sensor as a versatile tool in precision diagnosis.

Triblock probe-polyA-probe electrochemical interfacial engineering for the sensitive analysis of RNAi plants

RNA interference (RNAi) is under fast development in agriculture and brings new challenge for GMO analysis. We developed a electrochemical biosensor for the analysis of GM maize samples based on a polyA-DNA capturing probe. Ultrasensitive detection of 10 fM RNA was realized.

Electrochemiluminescence biosensor based on molybdenum disulfide-graphene quantum dots nanocomposites and DNA walker signal amplification for DNA detection

Based on the prominent electrochemiluminescence (ECL) performances of molybdenum disulfide-graphene quantum dots (MoS₂-GQDs) nanocomposite and combined with enzyme-assisted recycling DNA walker signal amplification, an "on-off" switch ECL biosensor was proposed for sensitive assay of specific DNA sequences. Noticeably, MoS₂ with two-dimensional nanosheet structure increased the loading capacity of GQDs to support abundant hairpin DNA (H). The composites of MoS₂ and GQDs facilitated the charge transfer in ECL process, which significantly improved the ECL signal to achieve an "on" state. Then, the DNA walker cyclic amplification was performed by adding the target DNA and exonuclease III (Exo III). Finally, the DNA2-Fc-DNA1 was introduced into the system as ECL signal quencher, turning the ECL signal into an "off" state. The sensitive assay of ultra-low concentration specific DNA sequences was realized according to the variation of ECL signal strength before and after the existence of target DNA. The proposed ECL biosensor showed a good linear relationship ranging from 1 nM to 100 aM with a detection limit of 25.1 aM, providing a powerful strategy for biomedical research and clinical analysis.

Construction of a Sensing Platform Based on DNA-Encoded Magnetic Beads and Copper Nanoclusters for Viral Gene Analysis with Target Recycling Amplification

The rapid and accurate monitoring of viral genes plays an important role in the area of disease diagnosis, biomedical research, and food safety. Herein, we successfully designed a sensing system that combined the technologies of target DNA recycling amplification, magnetic separation, and in situ formation of fluorescent copper nanoclusters (CuNCs) for viral DNA analysis. In the presence of target viral DNA (tDNA), a large quantity of output DNA (oDNA) was produced from hairpin DNA (hDNA) through an exonuclease III-assisted target recycling amplification strategy. Magnetic beads (MBs) labeled with capture DNA (cDNA) were hybridized with oDNA, and the partially complementary oDNA served as a bridge that could link AT-rich dsDNA on the surface of MBs, which led to a decrease of AT-rich dsDNA in solution after magnetic separation. On account of the lack of AT-rich dsDNA as a template in solution, in situ formation of fluorescent CuNCs was blocked, which resulted in a decrease in the fluorescence intensity at 590 nm. Therefore, taking advantage of one-step magnetic separation and in situ formation of CuNCs, the target viral DNA was sensitively and specifically detected in a linear range from 5 pM to 5 nM with a detection limit of 1 pM. The MB-based platform was not only reusable but also achieved magnetic separation, which could eliminate interferences in complex samples. The assay combining the MB-based probe with fluorescent CuNCs provided a universal, label-free, and reusable platform for viral DNA detection.

DNA Nanosieve-Based Regenerative Electrochemical Biosensor Utilizing Nucleic Acid Flexibility for Accurate Allele Typing in Clinical Samples

Herein, an interface-based DNA nanosieve that has the ability to differentiate ssDNA from dsDNA has been demonstrated for the first time. The DNA nanosieve could be readily built through thiol-DNA's self-assembly on the gold electrode surface, and its cavity size was tunable by varying the concentration of thiol-DNAs. Electrochemical chronocoulometry using [Ru(NH₃)₆]³⁺ as redox revealed that the average probe-to-probe separation in the 1 μM thiol-DNA-modified gold electrode was 10.6 ± 0.3 nm so that the rigid dsDNA with a length of ∼17 nm could not permeate the nanosieve, whereas the randomly coiled ssDNA could enter it due to its high flexibility, which has been demonstrated by square wave voltammetry and methylene blue labels through an upside-down hybridization format. After combining the transiently binding characteristic of a short DNA duplex and introducing a regenerative probe (the counterpart of ssDNA), a highly reproducible nanosieve-based E-DNA model was obtained with a relative standard deviation (RSD) as low as 2.7% over seven cycles. Finally, we built a regenerative nanosieve-based E-DNA sensor using a ligation cycle reaction as an ssDNA amplification strategy and realized one-sensor-based continuous measurement to multiple clinical samples with excellent allele-typing performance. This work holds great potential in low-cost and high-throughput analysis between biosensors and biochips and also opens up a new avenue in nucleic acid flexibility-based DNA materials for future applications in DNA origami and molecular logic gates.

A sensitive electrochemiluminescence DNA biosensor based on the signal amplification of ExoIII enzyme-assisted hybridization chain reaction combined with nanoparticle-loaded multiple probes

An electrochemiluminescence (ECL) DNA biosensor based on ExoIII exonuclease assistance and hybridization chain reaction (HCR) amplification technology has been constructed. ExoIII exonuclease and triple-helix DNA molecular switch are used in detecting a target in circulation. By combining HCR with AuNPs@DNA, a novel signal probe is built, which enables multiple signal amplification and the high-sensitive detection of transgenic rice BT63 DNA. The Fe₃O₄@Au solution is added to a magneto-controlled glassy carbon electrode, and sulfhydryl-modified capture DNA (CP) is immobilized on Fe₃O₄@Au through the Au-S bond. Mercaptoethanol is added to close sites and prevent the nonspecific adsorption of CP on the magnetron glassy carbon electrode. A target DNA is added to a constructed triple-helix DNA molecular centrifuge tube for reaction. Owing to base complementation and the reversible switching of the triple-helix DNA molecular state, the target DNA turns on the triple-helix DNA molecular switch and hybridizes with a long-strand recognition probe (RP) to form a double-stranded DNA (dsDNA). Exonuclease ExoIII is added to specifically recognize and cut the dsDNA and to release the target DNA. The target DNA strand then circulates back completely to open the multiple triple-helix DNA molecular switch, releasing a large number of signal transduction probes (STP). To hybridize with CP, a large amount of STP is added to the electrode. Finally, a AuNPs@DNA signal probe is added to hybridize with STP. H1 and H2 probes are added for the hybridization chain reaction and the indefinite extension of the primer strand on the probe. Then, tris-(bipyridyl)ruthenium(II) is added for ECL signal detection with PBS-tri-n-propylamine as the base solution. In the concentration range 1.0 × 10^-16 to 1.0 × 10^-8 mol/L of the target DNA, good linear relationship was achieved with the corresponding ECL signal. The detection limit is 3.6 × 10^-17 mol/L. The spiked recovery of the rice samples range from 97.2 to 101.5%. The sensor is highly sensitive and has good selectivity, stability, and reproducibility. A novel electrochemiluminescence biosensor with extremely higher sensitivity was prepared for the determination of ultra-trace amount transgenic rice BT63 DNA. The sensitivity was significantly improved by multiple signal enhancements. Firstly, a large number of signal transduction probes are released when the triple-helix DNA molecular switch unlock after recycles assisted by ExoIII exonuclease under target BT63 DNA; and then the signal transduction probes hybridize with the signal probes of AuNPs@(DNA-HCR) produced through hybridization chain reaction. Finally, the signal probes which were embedded with a large amount of electrochemiluminescence reagent produce high luminescence intensity. The detection limit was 3.6 × 10^-17 mol/L, which is almost the most sensitive methods reported.

Metal Nanoparticles for Electrochemical Sensing: Progress and Challenges in the Clinical Transition of Point-of-Care Testing

With the rise in public health awareness, research on point-of-care testing (POCT) has significantly advanced. Electrochemical biosensors (ECBs) are one of the most promising candidates for the future of POCT due to their quick and accurate response, ease of operation, and cost effectiveness. This review focuses on the use of metal nanoparticles (MNPs) for fabricating ECBs that has a potential to be used for POCT. The field has expanded remarkably from its initial enzymatic and immunosensor-based setups. This review provides a concise categorization of the ECBs to allow for a better understanding of the development process. The influence of structural aspects of MNPs in biocompatibility and effective sensor design has been explored. The advances in MNP-based ECBs for the detection of some of the most prominent cancer biomarkers (carcinoembryonic antigen (CEA), cancer antigen 125 (CA125), Herceptin-2 (HER2), etc.) and small biomolecules (glucose, dopamine, hydrogen peroxide, etc.) have been discussed in detail. Additionally, the novel coronavirus (2019-nCoV) ECBs have been briefly discussed. Beyond that, the limitations and challenges that ECBs face in clinical applications are examined and possible pathways for overcoming these limitations are discussed.

Ultrasensitive Electrochemical DNA Biosensor Fabrication by Coupling an Integral Multifunctional Zirconia-Reduced Graphene Oxide-Thionine Nanocomposite and Exonuclease I-Assisted Cleavage

In this work, a simple but sensitive electrochemical DNA biosensor for nucleic acid detection was developed by taking advantage of exonuclease (Exo) I-assisted cleavage for background reduction and zirconia-reduced graphene oxide-thionine (ZrO2-rGO-Thi) nanocomposite for integral DNA recognition, signal amplification, and reporting. The ZrO2-rGO nanocomposite was obtained by a one-step hydrothermal synthesis method. Then, thionine was adsorbed onto the rGO surface, via π-π stacking, as an excellent electrochemical probe. The biosensor fabrication is very simple, with probe DNA immobilization and hybridization recognition with the target nucleic acid. Then, the ZrO2-rGO-Thi nanocomposite was captured onto an electrode via the multicoordinative interaction of ZrO2 with the phosphate group on the DNA skeleton. The adsorbed abundant thionine molecules onto the ZrO2-rGO nanocomposite facilitated an amplified electrochemical response related with the target DNA. Since upon the interaction of the ZrO2-rGO-Thi nanocomposite with the probe DNA an immobilized electrode may also occur, an Exo I-assisted cleavage was combined to remove the unhybridized probe DNA for background reduction. With the current proposed strategy, the target DNA related with P53 gene could be sensitively assayed, with a wide linear detection range from 100 fM to 10 nM and an attractive low detection limit of 24 fM. Also, the developed DNA biosensor could differentiate the mismatched targets from complementary target DNA. Therefore, it offers a simple but effective biosensor fabrication strategy and is anticipated to show potential for applications in bioanalysis and medical diagnosis.