Recent Progress and Prospects in Catalytic Water Treatment

Qualitative and quantitative analysis of electrons donated by pollutants in electron transfer-based oxidation system: Electrochemical measurement and theoretical calculations

In order to gain a profound understanding of the fate of pollutants in advanced oxidation processes (AOPs), this study analyzed the electron contribution of pollutants qualitatively and quantitatively which rarely reported before. The rich electron transfer system was constructed by mesoporous carbon nitride (MCN) coupling with persulfate (PS) driven by visible light and the sulfanilamide antibiotics (SULs) were used as target contaminants. Firstly, the qualitative analysis of electron transfer in the system was confirmed systematically. The electron flow direction tested by i-t curves indicated that PS absorbed electrons, while SULs released electrons. The flow rate of electrons was also accelerated after the addition of SULs. The fitting curve between the kinetics and the peak potential difference tested by CV curve showed that the larger potential difference, the slower rate of oxidative degradation. Secondly, the quantification of electron transfer was achieved through theoretical calculations to simulate the interactions of the 'catalyst-oxidant-antibiotic' system. After the addition of SULs, the adsorption energy of the 'catalyst-oxidant-antibiotic' system was enhanced and the bond length of the peroxide bond was stretched. Notably, the electron transfer analysis results showed that the charge of SULs was around 0.032-0.056e, indicating that SULs pollutants played the role of electron contributors in the system. The oxidative degradation pathway included the direct cracking of S-N bond, shedding of marginal groups, ring-opening and hydroxyl addition reaction. This study clarified the electronic contribution of SULs in the oxidation system, providing necessary theoretical supplement for the analysis of the transformation of pollutants in AOPs.

Direct Z-scheme system of UiO-66 cubes wrapped with Zn0.5Cd0.5S nanoparticles for photocatalytic hydrogen generation synchronized with organic pollutant degradation

Optimized fabrication of Z-scheme photocatalyst based on MOF materials offers sustainable energy generation and environmental improvement due to their attractive properties. The Z-scheme heterojunctions consisting of UiO-66 cubes covered with Zn0.5Cd0.5S nanoparticles were fabricated by a facile solvothermal method. Thanks to the Z-scheme carrier transport under simulated sunlight irradiation, UiO-66@Zn0.5Cd0.5S exhibited enhanced photocatalytic performance of H2 generation synchronized with organic pollutant degradation in fluoroquinolone antibiotic wastewater. Synergistically, the highest comprehensive performance was obtained in ciprofloxacin solution. The H2 yield reached 224 μmol∙ g-1∙ h-1 and simultaneously the removal efficiency was up to 83.6 %. The degradation pathways revealed that the process of piperazine ring cleavage and decarboxylation also generates H protons, further promoting the production of H2. Therefore, the effective spatial separation and transfer of the photoinduced carriers are attributed to the good band structure, large specific surface area, and cooperative reduction and oxidation reactions of UiO-66@Zn0.5Cd0.5S, resulting in significant photocatalytic activity. The toxicity assessment of antibiotics and intermediate products during the photocatalytic reaction also verifies the reduction of environmental risk. This study highlights a promising way to expand the application of the MOFs-based photocatalyst in clean energy conversion coupling with water remediation.

Directional regulation of reactive oxygen species in titanium dioxide boosting the photocatalytic degradation performance of azo dyes

It has been widely accepted that the generation of reactive oxygen species such as superoxide radical, hydroxyl radical, and hydrogen peroxide during photocatalysis is responsible for the degradation of azo dyes. However, it is unclear which reactive oxygen species primarily contributes to the degradation efficiency of azo dyes. Here, we demonstrate that the directional regulation of reactive oxygen species in titanium dioxide (TiO2) to form superoxide radicals by ethylenediaminetetraacetic acid disodium salt (EDTA-2Na) can significantly improve the degradation performance of methyl orange. The optimized addition of EDTA-2Na can completely degrade azo dyes such as methyl orange, acid orange and alkaline orange at a concentration of 10 mg/L in about 20 min, which is not only higher than that achieved by pristine TiO2 under Xe lamp light but also far superior to the reported degradation efficiency of modified TiO2. Even under natural sunlight, this strategy can also effectively decompose azo dyes, demonstrating the great potential for practical water treatment using low-cost TiO2 photocatalysts.

Facilely tuning the coating layers of Fe nanoparticles from iron carbide to iron nitride for different performance in Fenton-like reactions

In this study, a series of Fe-based materials are facilely synthesized using MIL-88A and melamine as precursors. Changing the mass ratio of melamine and MIL-88A could tune the coating layers of generated zero-valent iron (Fe0) particles from Fe3C to Fe3N facilely. Compared to Fe/Fe3N@NC sample, Fe/Fe3C@NC exhibits better catalytic activity and stability to degrade carbamazepine (CBZ) with peroxymonosulfate (PMS) as oxidant. Free radical quenching tests, open-circuit potential (OCP) test and electron paramagnetic resonance spectra (EPR) prove that hydroxyl radicals (OH) and superoxide radical (O2-) are dominant reactive oxygen species (ROSs) with Fe/Fe3C@NC sample. For Fe/Fe3N@NC sample, the main ROSs are changed into sulfate radicals (SO4-) and high valent iron-oxo (Fe (IV)=O) species. In addition, the better conductivity of Fe3C is beneficial for the electron transfer from Fe0 to the Fe3C, thus could keep the activity of the surface sites and obtain better stability. DFT calculation reveals the better adsorption and activation ability of Fe3C than Fe3N. Moreover, PMS can also be adsorbed on the Fe sites of Fe3N with shorter FeO bonds and longer SO bonds than on Fe3C, the Fe (IV)=O is thus present in the Fe/Fe3N@NC/PMS system. This study provides a novel strategy for the development of highly active Fe-based materials for Fenton-like reactions and thus could promote their real application.

Tailoring the selective generation of oxidative organic radicals for toxic-by-product-free water decontamination

Peracetic acid (PAA) is emerging as a versatile agent for generating long-lived and selectively oxidative organic radicals (R-O•). Currently, the conventional transition metal-based activation strategies still suffer from metal ion leaching, undesirable by-products formation, and uncontrolled reactive species production. To address these challenges, we present a method employing BiOI with a unique electron structure as a PAA activator, thereby predominantly generating CH3C(O)O• radicals. The specificity of CH3C(O)O• generation ensured the superior performance of the BiOI/PAA system across a wide pH range (2.0 to 11.0), even in the presence of complex interfering substances such as humic acids, chloride ions, bicarbonate ions, and real-world water matrices. Unlike conventional catalytic oxidative methods, the BiOI/PAA system degrades sulfonamides without producing any toxic by-products. Our findings demonstrate the advantages of CH3C(O)O• in water decontamination and pave the way for the development of eco-friendly water decontaminations based on organic peroxides.

Insights into the transformation of natural organic matter during UV/peroxydisulfate treatment by FT-ICR MS and machine learning: Non-negligible formation of organosulfates

Natural organic matter (NOM) is a major sink of radicals in advanced oxidation processes (AOPs) and understanding the transformation of NOM is important in water treatment. By using Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS) in conjunction with machine learning, we comprehensively investigated the reactivity and transformation of NOM, and the formation of organosulfates during the UV/peroxydisulfate (PDS) process. After 60 min UV/PDS treatment, the CHO formula number and dissolved organic carbon concentration significantly decreased by 83.4 % and 74.8 %, respectively. Concurrently, the CHOS formula number increased substantially from 0.7 % to 20.5 %. Machine learning identifies DBE and AImod as the critical characteristics determining the reactivity of NOM during UV/PDS treatment. Furthermore, linkage analysis suggests that decarboxylation and dealkylation reactions are dominant transformation pathways, while the additions of SO3 and SO4 are also non-negligible. According to SHAP analysis, the m/z, number of oxygens, DBE and O/C of NOM were positively correlated with the formation of organosulfates in UV/PDS process. 92 organosulfates were screened out by precursor ion scan of HPLC-MS/MS and verified by UPLC-Q-TOF-MS, among which, 7 organosufates were quantified by authentic standards with the highest concentrations ranging from 2.1 to 203.0 ng L‒1. In addition, the cytotoxicity of NOM to Chinese Hamster Ovary (CHO) cells increased by 13.8 % after 30 min UV/PDS treatment, likely responsible for the formation of organosulfates. This is the first study to employ FT-ICR MS combined with machine learning to identify the dominant NOM properties affecting its reactivity and confirmed the formation of organosulfates from sulfate radical oxidation of NOM.

A review on the alternatives to antibiotics and the treatment of antibiotic pollution: Current development and future prospects

Antibiotics, widely used in the fields of medicine, animal husbandry, aquaculture, and agriculture, pose a serious threat to the ecological environment and human health. To prevent antibiotic pollution, efforts have been made in recent years to explore alternative options for antibiotics in animal feed, but the effectiveness of these alternatives in replacing antibiotics is not thoroughly understood due to the variation from case to case. Furthermore, a systematic summary of the specific applications and limitations of antibiotic removal techniques in the environment is crucial for developing effective strategies to address antibiotic contamination. This comprehensive review summarized the current development and potential issues on different types of antibiotic substitutes, such as enzyme preparations, probiotics, and plant extracts. Meanwhile, the existing technologies for antibiotic residue removal were discussed under the scope of application and limitation. The present work aims to highlight the strategy of controlling antibiotics from the source and provide valuable insights for green and efficient antibiotic treatment.

Advanced oxidation processes for water and wastewater treatment - Guidance for systematic future research

Advanced oxidation processes (AOPs) are a growing research field with a large variety of different process variants and materials being tested at laboratory scale. However, despite extensive research in recent years and decades, many variants have not been transitioned to pilot- and full-scale operation. One major concern are the inconsistent experimental approaches applied across different studies that impede identification, comparison, and upscaling of the most promising AOPs. The aim of this tutorial review is to streamline future studies on the development of new solutions and materials for advanced oxidation by providing guidance for comparable and scalable oxidation experiments. We discuss recent developments in catalytic, ozone-based, radiation-driven, and other AOPs, and outline future perspectives and research needs. Since standardized experimental procedures are not available for most AOPs, we propose basic rules and key parameters for lab-scale evaluation of new AOPs including selection of suitable probe compounds and scavengers for the measurement of (major) reactive species. A two-phase approach to assess new AOP concepts is proposed, consisting of (i) basic research and proof-of-concept (technology readiness levels (TRL) 1-3), followed by (ii) process development in the intended water matrix including a cost comparison with an established process, applying comparable and scalable parameters such as UV fluence or ozone consumption (TRL 3-5). Subsequent demonstration of the new process (TRL 6-7) is briefly discussed, too. Finally, we highlight important research tools for a thorough mechanistic process evaluation and risk assessment including screening for transformation products that should be based on chemical logic and combined with complementary tools (mass balance, chemical calculations).

Copper-Based Two-Dimensional Metal-Organic Frameworks for Fenton-like Photocatalytic Degradation of Methylene Blue under UV and Sunlight Irradiation

To efficiently degrade organic pollutants, photocatalysts must be effective under both ultraviolet (UV) radiation and sunlight. We synthesized a series of new metal-organic frameworks by using mild hydrothermal conditions. These frameworks incorporate three distinct bipyridyl ligands: pyrazine (pyr), 4,4'-bipyridine (bpy), and 1,2-bis(4-pyridyl)ethane (bpe). The resulting compounds are denoted as [Cu(pyz)(H2O)2MF6], [Cu(bpy)2(H2O)2]·MF6, and [Cu(bpe)2(H2O)2]·MF6·H2O [M = Zr (1, 3, and 5) and Hf (2, 4, and 6)]. All six compounds exhibited a two-dimensional crystal structure comprising infinitely nonintersecting linear chains. Compound 3 achieved 100% degradation of methylene blue (MB) after 8 min under UV irradiation and 100 min under natural sunlight in the presence of H2O2 as the electron acceptor. For compound 5, 100% MB degradation was achieved after 120 min under sunlight and 10 min under UV light. Moreover, reactive radical tests revealed that the dominant species involved in photocatalytic degradation are hydroxyl (•OH), superoxide radicals (•O2-), and photogenerated holes (h+). The photodegradation process followed pseudo-first-order kinetics, with photodegradation rate constants of 0.362 min-1 (0.039 min-1) for 3 and 0.316 min-1 (0.033 min-1) for 5 under UV (sunlight) irradiation. The developed photocatalysts with excellent activity and good recyclability are promising green catalysts for degrading organic pollutants during environmental decontamination.

From nano- to macroarchitectures: designing and constructing MOF-derived porous materials for persulfate-based advanced oxidation processes

Persulfate-based advanced oxidation processes (PS-AOPs) have gained significant attention as an effective approach for the elimination of emerging organic contaminants (EOCs) in water treatment. Metal-organic frameworks (MOFs) and their derivatives are regarded as promising catalysts for activating peroxydisulfate (PDS) and peroxymonosulfate (PMS) due to their tunable and diverse structure and composition. By the rational nanoarchitectured design of MOF-derived nanomaterials, the excellent performance and customized functions can be achieved. However, the intrinsic fine powder form and agglomeration ability of MOF-derived nanomaterials have limited their practical engineering application. Recently, a great deal of effort has been put into shaping MOFs into macroscopic objects without sacrificing the performance. This review presents recent advances in the design and synthetic strategies of MOF-derived nano- and macroarchitectures for PS-AOPs to degrade EOCs. Firstly, the strategies of preparing MOF-derived diverse nanoarchitectures including hierarchically porous, hollow, yolk-shell, and multi-shell structures are comprehensively summarized. Subsequently, the approaches of manufacturing MOF-based macroarchitectures are introduced in detail. Moreover, the PS-AOP application and mechanisms of MOF-derived nano- and macromaterials as catalysts to eliminate EOCs are discussed. Finally, the prospects and challenges of MOF-derived materials in PS-AOPs are discussed. This work will hopefully guide the design and development of MOF-derived porous materials in SR-AOPs.

Integrated In Situ Fabrication of CuO Nanorod-Decorated Polymer Membranes for the Catalytic Flow-Through Reduction of p-Nitrophenol

We developed a novel method to fabricate copper nanorods in situ in a poly(ether sulfone) (15 wt %) casting solution by a sonochemical reduction of Cu2+ ions with NaBH4. The main twist is the addition of ethanol to remove excess NaBH4 through Cu(0) catalyzed ethanolysis. This enabled the direct use of the resulting copper-containing casting dispersions for membrane preparation by liquid nonsolvent-induced phase separation and led to full utilization of the copper source, generating zero metal waste. We characterized the copper nanorods as presented in the membranes via scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and UV/vis spectroscopy. We could demonstrate that the rapid immobilization from reducing conditions led to the membrane incorporation of copper nanorods in a state of high reactivity, which also promoted the complete oxidation to CuO after fabrication. We further observed a large aspect ratio and crystal straining of the nanorods, likely resulting from growth around the matrix polymer. The entanglement with poly(ether sulfone) further facilitated a selective presentation at the pore surface of the final CuO-decorated membranes. The membranes also exhibit high water permeances of up to 2800 L/m2hbar. Our catalytic membranes achieved exceptionally high activities in the aqueous flow-through reduction of p-nitrophenol (p-NP), with turnover frequencies of up to 115 h-1, even surpassing those of other state-of-the-art catalytic membranes that incorporate Pd or Ag. Additionally, we demonstrated that catalytic hydrolysis of the reducing agent in water can lead to hydrogen gas formation and blocking of active sites during continuous catalytic p-NP hydrogenation. We illustrated that the accompanying conversion loss can be mitigated by facilitated gas transport in the water-filled pores, which is dependent on the orientation of the pore size gradient and the flow direction.

Recent Developments in Porphyrin-Based Metal-Organic Framework Materials for Water Remediation under Visible-Light Irradiation

Access to clean drinking water is a basic requirement, and eliminating pollutants from wastewater is important for saving water ecosystems. The porous structure and surface characteristics of metal-organic frameworks (MOFs) can function as a perfect scaffold for removing toxic compounds from wastewater. Porphyrins are promising building blocks for constructing MOFs. Porphyrin-based metal-organic frameworks (P-MOFs) have been fabricated using porphyrin ligands, metal clusters, or ions. These materials can harvest light from a wide region of the solar spectrum, and their framework morphology and physicochemical properties can be controlled by changing their peripheral subunits or metal ions. These porous crystalline materials have generated interest because of their distinctive characteristics, including large permanent porosity, interesting surface morphology, broad conformational diversity, high photostability, and semiconducting nature. This article discusses the recent progress and usefulness of P-MOFs. The fabrication procedures of P-MOFs are discussed, followed by the adsorptive and photocatalytic removal of contaminants from wastewater. The relationships between the geometries of P-MOFs and their light-harvesting and charge-transfer mechanisms for the photocatalytic degradation of pollutants are highlighted. Finally, some future perspectives and obstacles in the photodegradation usage of P-MOFs are discussed, along with feasible research directions to standardize efficient photocatalysts for improved photodegradation for water treatment.

Electronic structure regulation of Fe single atom coordinated nitrogen doping MoS2 catalyst enhances the Fenton-like reaction efficient for organic pollutant control

An efficient cathode for a Fenton-like reaction based on hydrogen peroxide (H2O2) has significant implications for the potential application of the advanced oxidation process. However, the low H2O2 selectivity and efficient activation remain challenging in wastewater treatment. In the present study, a single Fe atom doped, nitrogen-coordinated molybdenum disulfide (Fe1/N/MoS2) cathode that exhibited asymmetric wettability and self-absorption molecular oxygen was successfully prepared for pollutant degradation. The X-ray absorption near-edge structure and extended X-ray absorption fine structure of Fe1N3 in the Fe1/N/MoS2 catalyst were determined. The electronic structure demonstrated favorable H2O2 selectivity (75%) in a neutral solution and the cumulative hydroxyl radical concentration was 14 times higher than the pure carbon felt. After 10 consecutive reaction experiments, the removal ratio of paracetamol still reached 97%, and the catalytic performance did not decrease significantly. This work deeply understands the catalytic mechanism of Fenton-like reaction between single Fe atom and MoS2 double reaction sites, and proves that the regulation of the electronic structure of Fe single atom is an effective strategy to improve the activity of Fenton-like reaction.

Asymmetrically Coordinated Mn-S1 N3 Configuration Induces Localized Electric Field-Driven Peroxymonosulfate Activation for Remarkably Efficient Generation of 1 O2

Singlet oxygen (1 O2 ) species generated in peroxymonosulfate (PMS)-based advanced oxidation processes offer opportunities to overcome the low efficiency and secondary pollution limitations of existing AOPs, but efficient production of 1 O2 via tuning the coordination environment of metal active sites remains challenging due to insufficient understanding of their catalytic mechanisms. Herein, an asymmetrical configuration characterized by a manganese single atom coordinated is established with one S atom and three N atoms (denoted as Mn-S1 N3 ), which offer a strong local electric field to promote the cleavage of O─H and S─O bonds, serving as the crucial driver of its high 1 O2 production. Strikingly, an enhanced the local electric field caused by the dynamic inter-transformation of the Mn coordination structure (Mn-S1 N3 ↔ Mn-N3 ) can further downshift the 1 O2 production energy barrier. Mn-S1 N3 demonstrates 100% selective product 1 O2 by activation of PMS at unprecedented utilization efficiency, and efficiently oxidize electron-rich pollutants. This work provides an atomic-level understanding of the catalytic selectivity and is expected to guide the design of smart 1 O2 -AOPs catalysts for more selective and efficient decontamination applications.

Carrier confinement activated explicit solvent dynamic of CdS/BiVO4/H2O and optimized photocatalytic hydrogen evolution performances

Herein, using an electrophoretic deposition strategy, a S-scheme CdS (cubic)/BiVO4 (monoclinic) heterostructured photocatalyst is fabricated. The as-synthesized photocatalysts exhibit high carrier separation efficiency, prominent hydrogen evolution ability and high stability. The results of the detailed density functional theory (DFT) prove that the photogenerated electrons and holes are located in BiVO4 and CdS components, respectively. Besides, an explicit solvent model based on the electron-enriched region in CdS/BiVO4 heterojunction is designed deliberately to investigate the solid/liquid interface issues. Intriguing findings demonstrate that the surface hydrogen diffusing rate in CdS/BiVO4/H2O is faster than that of BiVO4/H2O and is highly associated with the electron-enrich effect, which has a greater capacity to promote water decomposition, the possibility of proton collision and photocatalytic hydrogen evolution. Notably, the H p orbital can participate in the electron-enrich effect during solvation, thus reforming the orbital energy level and activating the HER of the BiVO4 component in the CdS/BiVO4 system.

Photoelectrocatalytic degradation of high-density polyethylene microplastics on TiO2-modified boron-doped diamond photoanode

Microplastic (MP) accumulation in the environment is accelerating rapidly, which has led to their effects on both the ecosystem and human life garnering much attention. This study is the first to examine the degradation of high-density polyethylene (HDPE) MPs via photoelectrocatalysis (PEC) using a TiO2-modified boron-doped diamond (BDD/TiO2) photoanode. This study was divided into three stages: (i) preparation of the photoanode through electrophoretic deposition of synthetic TiO2 nanoparticles on a BDD electrode; (ii) characterization of the modified photoanode using electrochemical, structural, and optical techniques; and (iii) degradation of HDPE MPs by electrochemical oxidation and photoelectrocatalysis on bare and modified BDD electrodes under dark and UV light conditions. The results indicate that the PEC technique degraded 89.91 ± 0.08% of HDPE MPs in a 10-h reaction and was more efficient at a lower current density (6.89 mA cm-1) with the BDD/TiO2 photoanode compared to electrochemical oxidation on bare BDD.

Enhanced molecular oxygen activation via K/O interfacial modification for boosted electrocatalytic degradation over a broad pH range

Molecular oxygen activation plays an important role in the electrocatalytic degradation of recalcitrant pollutants. And the key lies in the tailoring of electronic structures over catalysts. Herein, carbon nitride with K/O interfacial modification (KOCN) was designed and fabricated for efficient molecular oxygen activation. Theoretical screening results revealed the possible substitution of peripheral N atoms by O atoms and the location of K atoms in the six-fold cavities of g-C3N4 framework. Spectroscopic and experimental results reveal that the existence of K/O promotes charge redistribution over as-prepared catalysts, leading to optimized electronic structures. Therefore, optimized oxygen adsorption was realized over 8 % KOCN, which was further converted into superoxide and singlet oxygen effectively. The rate constant of 8 % KOCN (1.8 × 10-2 min-1) reached 2.2 folds of pristine g-C3N4 (8.1 × 10-3 min-1) counterpart during tetracycline degradation. Moreover, the high electron mobility and excellent structural stability endow the catalyst with remarkable catalytic performance in a broad pH range of 3-11.

Critical Review of Pd-Catalyzed Reduction Process for Treatment of Waterborne Pollutants

Catalyzed reduction processes have been recognized as important and supplementary technologies for water treatment, with the specific aims of resource recovery, enhancement of bio/chemical-treatability of persistent organic pollutants, and safe handling of oxygenate ions. Palladium (Pd) has been widely used as a catalyst/electrocatalyst in these reduction processes. However, due to the limited reserves and high cost of Pd, it is essential to gain a better understanding of the Pd-catalyzed decontamination process to design affordable and sustainable Pd catalysts. This review provides a systematic summary of recent advances in understanding Pd-catalyzed reductive decontamination processes and designing Pd-based nanocatalysts for the reductive treatment of water-borne pollutants, with special focus on the interactions and transformation mechanisms of pollutant molecules on Pd catalysts at the atomic scale. The discussion begins by examining the adsorption of pollutants onto Pd sites from a thermodynamic viewpoint. This is followed by an explanation of the molecular-level reaction mechanism, demonstrating how electron-donors participate in the reductive transformation of pollutants. Next, the influence of the Pd reactive site structure on catalytic performance is explored. Additionally, the process of Pd-catalyzed reduction in facilitating the oxidation of pollutants is briefly discussed. The longevity of Pd catalysts, a crucial factor in determining their practicality, is also examined. Finally, we argue for increased attention to mechanism study, as well as precise construction of Pd sites under batch synthesis conditions, and the use of Pd-based catalysts/electrocatalysts in the treatment of concentrated pollutants to facilitate resource recovery.

3D Carbon Microspheres with a Maze-Like Structure and Large Mesopore Tunnels Built From Rapid Aerosol-Confined Coherent Salt/Surfactant Templating

Hierarchically porous carbons with tailor-made properties are essential for applications wherein rich active sites and fast mass transfer are required. Herein, a rapid aerosol-confined salt/surfactant templating approach is proposed for synthesizing hierarchically porous carbon microspheres (HPCMs) with a maze-like structure and large mesopore tunnels for high-performance tri-phase catalytic ozonation. The confined assembly in drying microdroplets is crucial for coherent salt (NaCl) and surfactant (F127) dual templating without macroscopic phase separation. The HPCMs possess tunable sizes, a maze-like structure with highly open macropores (0.3-30 µm) templated from NaCl crystal arrays, large intrawall mesopore tunnels (10-45 nm) templated from F127, and rich micropores (surface area >1000 m2 g-1 ) and oxygen heteroatoms originated from NaCl-confined carbonization of phenolic resin. The structure formation mechanism of the HPCMs and several influencing factors on properties are elaborated. The HPCMs exhibit superior performance in gas-liquid-solid tri-phase catalytic ozonation for oxalate degradation, owing to their hierarchical pore structure for fast mass transfer and rich defects and oxygen-containing groups (especially carbonyl) for efficient O3 activation. The reactive oxygen species responsible for oxalate degradation and the influences of several structure parameters on performance are discussed. This work may provide a platform for producing hierarchically porous materials for various applications.

o-Semiquinone Radical and o-Benzoquinone Selectively Degrade Aniline Contaminants in the Periodate-Mediated Advanced Oxidation Process

Advanced oxidation processes (AOPs) often employ strong oxidizing inorganic radicals (e.g., hydroxyl and sulfate radicals) to oxidize contaminants in water treatment. However, the water matrix could scavenge the strong oxidizing radicals, significantly deteriorating the treatment efficiency. Here, we report a periodate/catechol process in which reactive quinone species (RQS) including the o-semiquinone radical (o-SQ•-) and o-benzoquinone (o-Q) were dominant to effectively degrade anilines within 60 s. The second-order reaction rate constants of o-SQ•- and o-Q with aniline were determined to be 1.0 × 108 and 4.0 × 103 M-1 s-1, respectively, at pH 7.0, which accounted for 21% and 79% of the degradation of aniline with a periodate-to-catechol molar ratio of 1:1. The major byproducts were generated via addition or polymerization. The RQS-based process exhibited excellent anti-interference performance in the degradation of aniline-containing contaminants in real water samples in the presence of diverse inorganic ions and organics. Subsequently, we extended the RQS-based process by employing tea extract and dissolved organic matter as catechol replacements as well as metal ions [e.g., Fe(III) or Cu(II)] as periodate replacements, which also exhibited good performance in aniline degradation. This study provides a novel strategy to develop RQS-based AOPs for the highly selective degradation of aniline-containing emerging contaminants.

Electron-deficient Fe3O4@AC-NH2@Cu-MOF nanoparticles for enhanced degradation of electron-rich benzene derivatives via synergistic adsorption and catalytic oxidation

Benzene derivatives in wastewater have negative impacts on ecosystems and human health, making their removal prior to discharge imperative. In this study, Fe3O4@AC-NH2@Cu-opa (AC-NH2 = aminoclay, Cu-opa = [Cu(opa)(bipy)0.5(H2O)]n (H2opa = 3-(4-oxypyridinium-1-yl) phthalic acid)) nanoparticles (NPs) were synthesized as adsorbent and catalyst for phenolic compound removal from wastewater. Fe3O4@AC-NH2@Cu-opa NPs demonstrated outstanding performance in the adsorption of phenol, exhibiting a remarkable adsorption capacity of up to 166.39 mg g-1 according to the Langmuir model. The composite also exhibited higher Fenton activity toward the degradation of electron-rich organic phenolic pollutants, with a rate approximately 3.4 times higher than that of Fe3O4 alone. The high catalytic activity of the composite was attributed to the large surface area and abundant active sites of the 2D charge-separated Cu-MOF. Meanwhile, the superparamagnetism of the Fe3O4 core enabled magnetic recollection and reuse without any significant loss of activity. Therefore, use of Fe3O4@AC-NH2@Cu-opa/H2O2 shows potential in an efficient method for the removal of phenolic compounds from wastewater.

Peptide Stereochemistry Effects from pKa-Shift to Gold Nanoparticle Templating in a Supramolecular Hydrogel

The divergent supramolecular behavior of a series of tripeptide stereoisomers was elucidated through spectroscopic, microscopic, crystallographic, and computational techniques. Only two epimers were able to effectively self-organize into amphipathic structures, leading to supramolecular hydrogels or crystals, respectively. Despite the similarity between the two peptides' turn conformations, stereoconfiguration led to different abilities to engage in intramolecular hydrogen bonding. Self-assembly further shifted the pKa value of the C-terminal side chain. As a result, across the pH range 4-6, only one epimer predominated sufficiently as a zwitterion to reach the critical molar fraction, allowing gelation. By contrast, the differing pKa values and higher dipole moment of the other epimer favored crystallization. The four stereoisomers were further tested for gold nanoparticle (AuNP) formation, with the supramolecular hydrogel being the key to control and stabilize AuNPs, yielding a nanocomposite that catalyzed the photodegradation of a dye. Importantly, the AuNP formation occurred without the use of reductants other than the peptide, and the redox chemistry was investigated by LC-MS, NMR, and infrared scattering-type near field optical microscopy (IR s-SNOM). This study provides important insights for the rational design of simple peptides as minimalistic and green building blocks for functional nanocomposites.

Porphyrin-Based Nanomaterials for the Photocatalytic Remediation of Wastewater: Recent Advances and Perspectives

Self-organized, well-defined porphyrin-based nanostructures with controllable sizes and morphologies are in high demand for the photodegradation of hazardous contaminants under sunlight. From this perspective, this review summarizes the development progress in the fabrication of porphyrin-based nanostructures by changing their synthetic strategies and designs. Porphyrin-based nanostructures can be fabricated using several methods, including ionic self-assembly, metal-ligand coordination, reprecipitation, and surfactant-assisted methods. The synthetic utility of porphyrins permits the organization of porphyrin building blocks into nanostructures, which can remarkably improve their light-harvesting properties and photostability. The tunable functionalization and distinctive structures of porphyrin nanomaterials trigger the junction of the charge-transfer mechanism and facilitate the photodegradation of pollutant dyes. Finally, porphyrin nanomaterials or porphyrin/metal nanohybrids are explored to amplify their photocatalytic efficiency.

Step-by-step guide for electrochemical generation of highly oxidizing reactive species on BDD for beginners

Selecting the ideal anodic potential conditions and corresponding limiting current density to generate reactive oxygen species, especially the hydroxyl radical (•OH), becomes a major challenge when venturing into advanced electrochemical oxidation processes. In this work, a step-by-step guide for the electrochemical generation of •OH on boron-doped diamond (BDD) for beginners is shown, in which the following steps are discussed: i) BDD activation (assuming it is new), ii) the electrochemical response of BDD (in electrolyte and ferri/ferro-cyanide), iii) Tafel plots using sampled current voltammetry to evaluate the overpotential region where •OH is mainly generated, iv) a study of radical entrapment in the overpotential region where •OH generation is predominant according to the Tafel plots, and v) finally, the previously found ideal conditions are applied in the electrochemical degradation of amoxicillin, and the instantaneous current efficiency and relative cost of the process are reported.

N, S, and Cl tri-doped carbon boost the switching of radical to non-radical pathway in Fenton-like reactions: Synergism of N species and defects

Heteroatom doping represents a promising strategy for enhancing the generation of singlet oxygen (1O2) during the activation of peroxymonosulfate (PMS) using carbon-based catalysts; however, it remains a formidable challenge. In this study, we systematically controlled the structure of metal-free carbon-based materials by introducing different heteroatoms to investigate their efficacy in degrading organic pollutants in water via PMS activation. The results of reactive oxygen species detection showed that the dominant free radical in the four samples was different: CN (•SO4- and •OH), CNS (•O2-), CNCl (1O2), and CNClS (1O2). This led to the transformation of active species from free radicals to non-free radicals. The tri-doped carbons with nitrogen, sulfur, and chlorine (CNClS) exhibited exceptional performance in PMS activation and achieved a remarkable degradation efficiency of 95% within just 6 min for tetracycline. Moreover, a strong linear correlation was observed between the ratio of pyridine-N/graphite-N and ID/IG with the yield of 1O2, indicating that N species and defects play a crucial role in CNClS as they facilitate the transition from radical to non-radical pathways during PMS activation. These findings highlight the possibility that adjustable tri-heteroatom doping will expand the Fenton-like reaction for the treatment of actual wastewater.

Single atom catalyst-mediated generation of reactive species in water treatment

Water is one of the most essential components in the sustainable development goals (SDGs) of the United Nations. With worsening global water scarcity, especially in some developing countries, water reuse is gaining increasing acceptance. A key challenge in water treatment by conventional treatment processes is the difficulty of treating low concentrations of pollutants (micromolar to nanomolar) in the presence of much higher levels of inorganic ions and natural organic matter (NOM) in water (or real water matrices). Advanced oxidation processes (AOPs) have emerged as an attractive treatment technology that generates reactive species with high redox potentials (E0) (e.g., hydroxyl radical (HO˙), singlet oxygen (1O2), sulfate radical (SO4˙-), and high-valent metals like iron(IV) (Fe(IV)), copper(III) (Cu(III)), and cobalt(IV) (Co(IV))). The use of single atom catalysts (SACs) in AOPs and water treatment technologies has appeared only recently. This review introduces the application of SACs in the activation of hydrogen peroxide and persulfate to produce reactive species in treatment processes. A significant part of the review is devoted to the mechanistic aspects of traditional AOPs and their comparison with those triggered by SACs. The radical species, SO4˙- and HO˙, which are produced in both traditional and SACs-activated AOPs, have higher redox potentials than non-radical species, 1O2 and high-valent metal species. However, SO4˙- and HO˙ radicals are non-selective and easily affected by components of water while non-radicals resist the impact of such constituents in water. Significantly, SACs with varying coordination environments and structures can be tuned to exclusively generate non-radical species to treat water with a complex matrix. Almost no influence of chloride, carbonate, phosphate, and NOM was observed on the performance of SACs in treating pollutants in water when nonradical species dominate. Therefore, the appropriately designed SACs represent game-changers in purifying water vs. AOPs with high efficiency and minimal interference from constituents of polluted water to meet the goals of water sustainability.

Enhanced Oxidation of Organic Compounds by the Ferrihydrite-Ferrate System: The Role of Intramolecular Electron Transfer and Intermediate Iron Species

Previous studies mostly held that the oxidation capacity of ferrate depends on the involvement of intermediate iron species (i.e., FeIV/FeV), however, the potential role of the metastable complex was disregarded in ferrate-based heterogeneous catalytic oxidation processes. Herein, we reported a complexation-mediated electron transfer mechanism in the ferrihydrite-ferrate system toward sulfamethoxazole (SMX) degradation. A synergy between intermediate FeIV/FeV oxidation and the intramolecular electron transfer step was proposed. Specifically, the conversion of phenyl methyl sulfoxide (PMSO) to methyl phenyl sulfone (PMSO2) suggested that FeIV/FeV was involved in the oxidation of SMX. Moreover, based on the in situ Raman test and chronopotentiometry analysis, the formation of the metastable complex of ferrihydrite/ferrate was found, which possesses higher oxidation potential than free ferrate and could achieve the preliminary oxidation of organics via the electron transfer step. In addition, the amino group of SMX could complex with ferrate, and the resulting metastable complex of ferrihydrite/ferrate would combine further with SMX molecules, leading to intramolecular electron transfer and SMX degradation. The ferrate loss experiments suggested that ferrihydrite could accelerate the decomposition of ferrate. Finally, the effects of pH value, anions, humic acid, and actual water on the degradation of SMX by ferrihydrite-ferrate were also revealed. Overall, ferrihydrite demonstrated high catalytic capacity, good reusability, and nontoxic performance for ferrate activation. The ferrihydrite-ferrate process may be a green and promising method for organic removal in wastewater treatment.

Optimizing the performance of Fe-based metal-organic frameworks in photo-Fenton processes: Mechanisms, strategies and prospects

Contaminants in water pose a significant challenge as they are harmful and difficult to treat using conventional methods. Therefore, various new methods have been proposed to degrade organic pollutants in water, among which the photo-Fenton process is considered promising. In recent years, Fe-based metal-organic frameworks (Fe-MOFs) have gained attention and found applications in different fields due to their cost-effectiveness, non-toxic nature, and unique porous structure. Many researchers have applied Fe-MOFs to the photo-Fenton process in recent years and achieved good results. This review focuses on describing different strategies for enhancing the performance of Fe-MOFs in the photo-Fenton process. Also, the mechanism of MOF in the photo-Fenton process is described in detail. Finally, prospects for the application of Fe-MOFs in photo-Fenton systems for the treatment of organic pollutants in water are presented. This study provides information and ideas for researchers to use Fe-MOFs to remove organic pollutants from water by photo-Fenton process.

Construction of Core-shell Sb2 s3 @Cds Nanorod with Enhanced Heterointerface Interaction for Chromium-Containing Wastewater Treatment

How to collaboratively reduce Cr(VI) and break Cr(III) complexes is a technical challenge to solve chromium-containing wastewater (CCW) pollution. Solar photovoltaic (SPV) technology based on semiconductor materials is a potential strategy to solve this issue. Sb2 S3 is a typical semiconductor material with total visible-light harvesting capacity, but its large-sized structure highly aggravates disordered photoexciton migration, accelerating the recombination kinetics and resulting low-efficient photon utilization. Herein, the uniform mesoporous CdS shell is in situ formed on the surface of Sb2 S3 nanorods (NRs) to construct the core-shell Sb2 S3 @CdS heterojunction with high BET surface area and excellent near-infrared light harvesting capacity via a surface cationic displacement strategy, and density functional theory thermodynamically explains the breaking of SbS bonds and formation of CdS bonds according to the bond energy calculation. The SbSCd bonding interaction and van der Waals force significantly enhance the stability and synergy of Sb2 S3 /CdS heterointerface throughout the entire surface of Sb2 S3 NRs, promoting the Sb2 S3 -to-CdS electron transfer due to the formation of built-in electric field. Therefore, the optimized Sb2 S3 @CdS catalyst achieves highly enhanced simulated sunlight-driven Cr(VI) reduction (0.154 min-1 ) and decomplexation of complexed Cr(III) in weakly acidic condition, resulting effective CCW treatment under co-action of photoexcited electrons and active radicals. This study provides a high-performance heterostructured catalyst for effective CCW treatment by SPV technology.

Surface Modification of ZnO with Sn(IV)-Porphyrin for Enhanced Visible Light Photocatalytic Degradation of Amaranth Dye

Two hybrid composite photocatalysts, denoted as SnP/AA@ZnO and SnP@ZnO, were fabricated by a reaction of trans-dihydroxo[5,10,15,20-tetrakis(4-pyridyl)porphyrinato]tin(IV) (SnP) and ZnO with and without pretreatment of adipic acid (AA), respectively. In SnP@ZnO, SnP and ZnO are likely held together by a coordinative interaction between the pyridyl N atoms of SnP and the Zn atoms on the surface of ZnO. In the case of SnP/AA@ZnO, the SnP centers were robustly coupled with ZnO nanoparticles through the AA anchors. SnP/AA@ZnO exhibited largely enhanced photocatalytic activities for the degradation of anionic amaranth (AM) dye under a visible light irradiation, compared to SnP, ZnO, and SnP@ZnO. The degradation efficiency of AM by SnP/AA@ZnO was 95% within 60 min at a rate constant of 0.048 min-1. The remarkable photocatalytic oxidation performance of SnP/AA@ZnO was mainly attributed to the synergistic effect between SnP and ZnO. This study is valuable for the development of highly effective composite photocatalytic systems in advanced oxidation processes and is of importance for the treatment of wastewater containing dyes.

Material Design Strategies for Recovery of Critical Resources from Water

Population growth, urbanization, and decarbonization efforts are collectively straining the supply of limited resources that are necessary to produce batteries, electronics, chemicals, fertilizers, and other important products. Securing the supply chains of these critical resources via the development of separation technologies for their recovery represents a major global challenge to ensure stability and security. Surface water, groundwater, and wastewater are emerging as potential new sources to bolster these supply chains. Recently, a variety of material-based technologies have been developed and employed for separations and resource recovery in water. Judicious selection and design of these materials to tune their properties for targeting specific solutes is central to realizing the potential of water as a source for critical resources. Here, the materials that are developed for membranes, sorbents, catalysts, electrodes, and interfacial solar steam generators that demonstrate promise for applications in critical resource recovery are reviewed. In addition, a critical perspective is offered on the grand challenges and key research directions that need to be addressed to improve their practical viability.

Preparation and Characterization of a Coordination Polymer Based on Iron (III)-Cyamelurate as a Superior Catalyst for Heterogeneous Fenton-Like Processes

We report on a new iron (iii)-cyamelurate-based coordination polymer. The new material based on a heptazine derivative was prepared in aqueous medium and characterized by a variety of techniques including TGA, FTIR, XRD, HRTEM, and STEM. Due to the high structural stability of the complex in aqueous media, its heterogeneous Fenton-like catalytic activity was evaluated using a model molecule. The results obtained showed a high catalytic activity in both in basic and acid media. The pseudo-first-order rate constants normalized by iron(III) concentrations was approximately 1000 times higher than the result obtained for traditional heterogeneous catalysts based on iron(III) oxyhydroxides. The best observed catalytic activities were attributed to the increase in the binding sites of Fe³⁺ ions, in parallel with the increased exposure of the catalytic sites, leading to a higher atomic efficiency of the reaction.

Nanoconfinement-enhanced Fenton-like polymerization via hollow hetero-shell carbon for reducing carbon emissions in organic wastewater purification

Lower reaction speed and excessive oxidant inputs impede the removal of contaminants from water via the advanced oxidation processes based on peroxymonosulfate. Herein, we report a new confined catalysis paradigm via the hollow hetero-shell structured CN@C (H-CN@C), which permits effective decontamination through polymerization with faster reaction rates and lower oxidant dosage. The confined space structures regulated the CN and CO and electron density of the inner shell, which increased the electron transfer rate and mass transfer rate. As a result, CN in H-CN@C-10 reacted with peroxymonosulfate in preference to CO to generate singlet oxygen, improving the second-order reaction kinetics by 503 times. The identification of oxidation products implied that bisphenol AF could effectively remove by polymerization, which could reduce carbon dioxide emissions. These favorable properties make the nanoconfined catalytic polymerization of contaminants a remarkably promising nanocatalytic water purification technology.

Vertical Growth of WO3 Nanosheets on TiO2 Nanoribbons as 2D/1D Heterojunction Photocatalysts with Improved Photocatalytic Performance under Visible Light

We report the construction of 2D/1D heterojunction photocatalysts through the hydrothermal growth of WO3 nanosheets on TiO2 nanoribbons for the first time. Two-dimensional WO3 nanosheets were vertically arrayed on the surface of TiO2 nanoribbons, and the growth density could be simply controlled by adjusting the concentration of the precursors. The construction of WO3/TiO2 heterojunctions not only decreases the band gap energy of TiO2 from 3.12 to 2.30 eV and broadens the photoresponse range from the UV region to the visible light region but also significantly reduces electron–hole pair recombination and enhances photo-generated carrier separation. Consequently, WO3/TiO2 heterostructures exhibit improved photocatalytic activity compared to pure WO3 nanosheets and TiO2 nanoribbons upon visible light irradiation. WO3/TiO2-25 possesses the highest photocatalytic activity and can remove 92.8% of RhB pollutants in 120 min. Both further increase and decrease in the growth density of WO3 nanosheets result in an obvious reduction in photocatalytic activity. The kinetic studies confirmed that the photocatalytic degradation of RhB follows the kinetics of the pseudo-first-order model. The present study demonstrates that the prepared WO3/TiO2 2D/1D heterostructures are promising materials for photocatalytic removal of organic pollutants to produce clean water.

Enhanced Interfacial Electron Transfer by Asymmetric Cu-Ov -In Sites on In2 O3 for Efficient Peroxymonosulfate Activation

Enhancing the peroxymonosulfate (PMS) activation efficiency to generate more radicals is vital to promote the Fenton-like reaction activity, however, how to promote the PMS adsorption and accelerate the interfacial electron transfer to boost its activation kinetics remains a great challenge. Herein, we prepared Cu-doped defect-rich In₂ O₃ (Cu-In₂ O₃ /O_v ) catalysts containing asymmetric Cu-O_v -In sites for PMS activation in water purification. The intrinsic catalytic activity is that the side-on adsorption configuration of the O-O bond (Cu-O-O-In) at the Cu-O_v -In sites significantly stretches the O-O bond length. Meanwhile, the Cu-O_v -In sites increase the electron density near the Fermi energy level, promoting more and faster electron transfer to the O-O bond for generating more SO₄ ⋅^- and ⋅OH. The degradation rate constant of tetracycline achieved by Cu-In₂ O₃ /O_v is 31.8 times faster than In₂ O₃ /O_v , and it shows the possibility of membrane reactor for practical wastewater treatment.

Defective iron based metal-organic frameworks derived from zero-valent iron for highly efficient fenton-like catalysis

Introducing crystal defects into iron based metal-organic frameworks (Fe-MOFs) is regarded as a promising strategy to enhance Fenton-like performance. However, developing a facile and effective strategy to construct defective Fe-MOFs as highly efficient Fenton-like catalyst is still a challenge. Herein, MIL-100(Fe) (Def-MIL-100(Fe)) with missing ligands defects was synthesized by a simple heterogeneous reaction using zero-valent iron. The bisphenol A degradation efficiency in the Def-MIL-100(Fe)/H₂O₂ system reached up to 91.26% within 10 min at pH 4 with a low catalyst dosage of 0.05 g/L, while the perfect MIL-100(Fe) has almost no Fenton-like performance. It was observed that missing ligands defects in the Def-MIL-100(Fe) play a key role in the Fenton-like reaction. The missing ligands defects could increase the Lewis acidity for fast H₂O₂ adsorption and accelerate the electron transfer between Fe^II and Fe^III cycling, leading to faster and more·OH generation. Moreover, the missing ligands defects could promote the mass transfer for improving·OH utilization efficiency. This work provides a novel strategy to construct defective Fe-MOFs as highly efficient Fenton-like catalyst to degrade organic pollutants in water.

Redox-Active Polymers as Robust Electron-Shuttle Co-Catalysts for Fast Fe3+/Fe2+ Circulation and Green Fenton Oxidation

Accelerating the rate-limiting Fe³⁺/Fe²⁺ circulation in Fenton reactions through the addition of reducing agents (or co-catalysts) stands out as one of the most promising technologies for rapid water decontamination. However, conventional reducing agents such as hydroxylamine and metal sulfides are greatly restricted by three intractable challenges: (1) self-quenching effects, (2) heavy metal dissolution, and (3) irreversible capacity decline. To this end, we, for the first time, introduced redox-active polymers as electron shuttles to expedite the Fe³⁺/Fe²⁺ cycle and promote H₂O₂ activation. The reduction of Fe³⁺ mainly took place at active N-H or O-H bonds through a proton-coupled electron transfer process. As electron carriers, H atoms at the solid phase could effectively inhibit radical quenching, avoid metal dissolution, and maintain long-term reducing capacity via facile regeneration. Experimental and density functional theory (DFT) calculation results indicated that the activity of different polymers shows a volcano curve trend as a function of the energy barrier, highest occupied molecular orbital-lowest unoccupied molecular orbital (HOMO-LUMO) gap, and vertical ionization potential. Thanks to the appropriate redox ability, polyaniline outperforms other redox-active polymers (e.g., poypyrrole, hydroquinone resin, poly(2,6-diaminopyridine), and hexaazatrinaphthalene framework) with a highest iron reduction capacity up to 5.5 mmol/g, which corresponds to the state transformation from leucoemeraldine to emeraldine. Moreover, the proposed system exhibited high pollutant removal efficiency in a flow-through reactor for 8000 bed volumes without an obvious decline in performance. Overall, this work established a green and sustainable oxidation system, which offers great potential for practical organic wastewater remediation.

Hybrid Composite of Sn(IV)-Porphyrin and Mesoporous Structure for Enhanced Visible Light Photocatalytic Degradation of Organic Dyes

Two hybrid composites (SnP@MCM-41 and SnP@SiO₂) were fabricated by chemical adsorption of (trans-dihydroxo)(5,10,15,20-tetraphenylporphyrinato)tin(IV) (SnP) on mesoporous structured Mobil Composition of Matter No. 41 (MCM-41) and SiO₂ nanoparticles. These materials were characterized by Fourier-transform infrared spectroscopy, ultraviolet-visible spectroscopy, fluorescence spectroscopy, transmission electron microscopy, and field-emission scanning electron microscopy techniques. The incorporation of SnP into MCM-41 and SiO₂ supports efficient photocatalytic degradation of the anionic erioglaucine, cationic rhodamine B, and neutral m-cresol purple dyes under visible light irradiation in an aqueous solution. The performances of degradation of these dyes by these photocatalysts under visible light irradiation varied from 87 to 95%. The pseudo-first-order degradation rate constant of organic dyes for SnP@MCM-41 was higher than those of SnP@SiO₂ and SnP. These visible light photocatalysts showed remarkable stability and reliable reusability.

Visible-light-driven iron-based heterogeneous photo-Fenton catalysts for wastewater decontamination: A review of recent advances

Visible-light-driven heterogeneous photo-Fenton process has emerged as the most promising Fenton-derived technology for wastewater decontamination, owing to its prominent superiorities including the potential utilization of clean energy (solar light), and acceleration of ≡Fe(II)/≡Fe(III) dynamic cycle. As the core constituent, catalysts play a pivotal role in the photocatalytic activation of H₂O₂ to yield reactive oxidative species (ROS). To date, all types of iron-based heterogeneous photo-Fenton catalysts (Fe-HPFCs) have been extensively reported by the scientific community, and exhibited satisfactory catalytic performance towards pollutants decomposition, sometimes even exceeding the homogeneous counterparts (Fe(II)/H₂O₂). However, the relevant reviews on Fe-HPFCs, especially from the viewpoint of catalyst-self design are extremely limited. Therefore, this state-of-the-art review focuses on the available Fe-HPFCs in literatures, and gives their classification based on their self-characteristics and modification strategies for the first time. Two classes of representative Fe-HPFCs, conventional inorganic semiconductors of Fe-containing minerals and newly emerging Fe-based metal-organic frameworks (Fe-MOFs) are comprehensively summarized. Moreover, three universal strategies including (i) transition metal (TMs) doping, (ii) construction of heterojunctions with other semiconductors or plasmonic materials, and (iii) combination with supporters were proposed to tackle their inherent defects, viz., inferior light-harvesting capacity, fast recombination of photogenerated carriers, slow mass transfer and low exposure and uneven dispersion of active sites. Lastly, a critical emphasis was also made on the challenges and prospects of Fe-HPFCs in wastewater treatment, providing valuable guidance to researchers for the reasonable construction of high-performance Fe-HPFCs.

Efficient Visible-Light-Driven Tetracycline Degradation and Cr(VI) Reduction over a LaNi1-xFexO3 (0 ≤ x ≤ 1)/g-C3N4 Type-II Heterojunction Photocatalyst

The development of efficient, stable, and visible-light-responsive photocatalysts is crucial to address the pollution of water bodies by toxic heavy metal ions and organic antibiotics. Herein, a series of LaNi_1-xFe_xO₃/g-C₃N₄ heterojunction photocatalysts are prepared by a simple wet chemical method. Moreover, LaNi_0.8Fe_0.2O₃/g-C₃N₄ composites are characterized by various methods, including structure, morphology, optical, and electrochemical methods and tetracycline degradation and photocatalytic reduction of Cr(VI) under visible light irradiation. Then, the photocatalytic performance of as-prepared LaNi_0.8Fe_0.2O₃/g-C₃N₄ composites is evaluated. Compared with pure LaNi_0.8Fe_0.2O₃ and g-C₃N₄, the LaNi_0.8Fe_0.2O₃/g-C₃N₄ composite photocatalysts exhibit excellent photocatalytic performance due to synergy of doping and constructing heterojunctions. The results show that the doping of Fe ions can increase the concentration of oxygen vacancies, which is ultimately beneficial to the formation of electron traps. Moreover, the type-II heterojunction formed between LaNi_0.8Fe_0.2O₃ and g-C₃N₄ effectively strengthens the separation and transfer of photoinduced carriers, thereby promoting photocatalytic activity. Furthermore, the photocatalytic activity of the LaNi_0.8Fe_0.2O₃/g-C₃N₄ photocatalyst remains almost unchanged after three cycles, indicating long-term stability. Ultimately, the photocatalytic mechanism of the LaNi_0.8Fe_0.2O₃/g-C₃N₄ composites is proposed.

Chemical Cyclic Amplification: Hydroxylamine Boosts the Fenton Reaction for Versatile and Scalable Biosensing

Nucleic acid detection is undoubtedly one of the most important research fields to meet the medical needs of genetic disease diagnosis, cancer treatment, and infectious disease prevention. However, the practical detection methods based on biological amplification are complex and time-consuming and require highly trained operators. Herein, we report a simple, rapid, and sensitive method for the nucleic acid assay by fluorescence or naked eye using chemical cyclic amplification. The addition of hydroxylamine (HA) during the Fenton reaction can continuously generate hydroxyl radicals (^•OH) via Fe³⁺/Fe²⁺ cycle, termed as "hydroxylamine boosts the Fenton reaction (Fenton-HA system)". Meanwhile, the reducing substances, such as terephthalic acid or o-phenylenediamine, react with ^•OH to generate oxidized substances that can be recognized by the naked eye or detected by fluorescence so as to realize the detection of Fe³⁺. The concentration of Fe³⁺ has a good linear relationship with fluorescence intensity in the range of 0.1 to 100 nM, and the limit of detection is calculated to be 0.03 nM (S/N = 3). Subsequently, Fe was introduced into the nucleic acid hybridization system after the Fe source was transformed into Fe³⁺, and the nucleic acids were indirectly determined by this method. This Fenton-HA system was used for sensing HIV-DNA and miRNA-21 to verify the validity of this method in nucleic acid detection. The detection limits were as low as 2.5 pM for HIV-DNA and 3 pM for miRNA-21. We believe that our work has unlocked an efficient signal amplification strategy, which is expected to develop a new generation of highly sensitive chemical biosensors.

Electron-transfer-based peroxymonosulfate activation on defect-rich carbon nanotubes: Understanding the substituent effect on the selective oxidation of phenols

Nanocarbon-based persulfate oxidation technologies are promising for green elimination of phenolic pollutants. Previous studies revealed the electron transfer via defective carbon nanotube (CNTs) for selective oxidation of various phenols. However, an underlying relationship between the molecular structure of phenols and the selectivity of electron transfer-induced oxidation has not been well understood. Herein, we report that defect-rich CNTs could initiate electron-transfer regime from phenols to peroxymonosulfate (PMS), resulting in the efficient degradation of phenols. Further studies uncover a distinctive substituent group-dependent selective oxidation of phenols via the CNT-mediated electron transfer process. Specifically, the degradation rate of para-substituted phenols with electron-donating groups (e.g., -NH₂ and -OCH₃) is faster than those with electron-withdrawing groups (e.g., -NO₂ and -COOH). For a kind of substituted phenols, the substituent position has a great influence on the phenols degradation and their degradation rates follow this sequence: para > ortho > meta -position. Besides, increasing the number of the substituent group can accelerate the degradation of substituted phenols. This study elucidates the substituent effect on the electron transfer-dominated selective oxidation of phenols for the first time, which guides the application of carbon/persulfate system for the targeted remediation of phenols-polluted wastewater.

Effect of Pharmaceutical Sludge Pre-Treatment with Fenton/Fenton-like Reagents on Toxicity and Anaerobic Digestion Efficiency

Sewage sludge is successfully used in anaerobic digestion (AD). Although AD is a well-known, universal and widely recognized technology, there are factors that limit its widespread use, such as the presence of substances that are resistant to biodegradation, inhibit the fermentation process or are toxic to anaerobic microorganisms. Sewage sludge generated by the pharmaceutical sector is one such substance. Pharmaceutical sewage sludge (PSS) is characterized by high concentrations of biocides, including antibiotics and other compounds that have a negative effect on the anaerobic environment. The aim of the present research was to determine the feasibility of applying Advanced Oxidation Processes (AOP) harnessing Fenton's (Fe²⁺/H₂O₂) and Fenton-like (Fe³⁺/H₂O₂) reaction to PSS pre-treatment prior to AD. The method was analyzed in terms of its impact on limiting PSS toxicity and improving methane fermentation. The use of AOP led to a significant reduction of PSS toxicity from 53.3 ± 5.1% to 35.7 ± 3.2%, which had a direct impact on the taxonomic structure of anaerobic bacteria, and thus influenced biogas production efficiency and methane content. Correlations were found between PSS toxicity and the presence of Archaea and biogas yields in the Fe²⁺/H₂O₂ group. CH₄ production ranged from 363.2 ± 11.9 cm³ CH₄/g VS in the control PSS to approximately 450 cm³/g VS. This was 445.7 ± 21.6 cm³ CH₄/g VS (1.5 g Fe²⁺/dm³ and 6.0 g H₂O₂/dm³) and 453.6 ± 22.4 cm³ CH₄/g VS (2.0 g Fe²⁺/dm³ and 8.0 g H₂O₂/dm³). The differences between these variants were not statistically significant. Therefore, due to the economical use of chemical reagents, the optimal tested dose was 1.5 g Fe²⁺/6.0 g H₂O₂. The use of a Fenton-like reagent (Fe³⁺/H₂O₂) resulted in lower AD efficiency (max. 393.7 ± 12.1 cm³ CH₄/g VS), and no strong linear relationships between the analyzed variables were found. It is, therefore, a more difficult method to estimate the final effects. Research has proven that AOP can be used to improve the efficiency of AD of PSS.

Efficient Activation of Peroxymonosulfate by V-Doped Graphitic Carbon Nitride for Organic Contamination Remediation

Advanced oxidation processes (AOPs) based on peroxymonosulfate (PMS) activation have been developed as an ideal pathway for completely eradication of recalcitrant organic pollutants from water environment. Herein, the V-doped graphitic carbon nitride (g-C₃N₄) is rationally fabricated by one-step thermal polymerization method to activate PMS for contamination decontamination. The results demonstrate the V atoms are successfully integrated into the framework of g-C₃N₄, which can effectively improve light absorption intensity and enhance charge separation. The V-doped g-C₃N₄ displays superior catalytic performance for PMS activation. Moreover, the doping content has a great influence on the activation performances. The radical quenching experiments confirm •O₂^-, SO₄^•-, and h⁺ are the significant species in the catalytic reaction. This work would provide a feasible strategy to exploit efficient g-C₃N₄-based material for PMS activation.

Hypercrosslinking porous polymer layers on TiO2-graphene photocatalyst: Enhanced adsorption of water pollutants for efficient degradation

Solar-driven photocatalysis offers an environmentally friendly and sustainable approach for the degradation of organic pollutants in water without chemical additives, but the low specific surface area and adsorption capacity of common photocatalysts restricts the surface reactions with the contaminants. Herein, we hypercrosslinked polymer layers on TiO₂-graphene surface to enlarge the specific surface area from 136 to 988 m²/g, leading to a high adsorption capacity of sulfadiazine as 54.3 mg/g, which is 15.5 times that of TiO₂-graphene (3.5 mg/g). The adsorption kinetics reveals the combination of physical and chemical adsorption by porous benzene-based polymer for sulfadiazine enrichment. Besides, the polymer layers with broad light absorption enable the composite to function efficiently as visible-light-driven photocatalysts. Thus, the as-designed composite exhibits excellent performance for sulfadiazine removal by integrating the adsorptive and photocatalytic processes, especially for the diluted sulfadiazine solution. More importantly, the porous polymer layer can function as a filter for weakening the interference of TiO₂ surface with the natural matters from complex water matrices. Based on the identification of dominant reactive species, the possible attacking pathway and the sulfadiazine subsequent degradation are presented. Further, the enhanced adsorption and photodegradation efficiency can also be achieved for the removal of other typical pollutants such as 4-chlorophenol and methylene blue. This study highlights an adsorption-enhanced-degradation mechanism for water pollutants that can direct the design of high-performance photocatalysts under visible light.

Sn(IV)-Porphyrin-Based Nanostructures Featuring Pd(II)-Mediated Supramolecular Arrays and Their Photocatalytic Degradation of Acid Orange 7 Dye

Two robust Sn(IV)-porphyrin-based supramolecular arrays (1 and 2) were synthesized via the reaction of trans-Pd(PhCN)2Cl2 with two precursor building blocks (SnP1 and SnP2). The structural patterns in these architectures vary from 2D to 3D depending on the axial ligation of Sn(IV)-porphyrin units. A discrete 2D tetrameric supramolecule (1) was constructed by coordination of {(trans-dihydroxo)[5,10-bis(4-pyridyl)-15,20-bis(phenyl) porphyrinato]}tin(IV) (SnP1) with trans-PdCl2 units. In contrast, the coordination between the {(trans-diisonicotinato)[5,10-bis(4-pyridyl)-15,20-bis(phenyl)porphyrinato]}tin(IV) (SnP2) and trans-PdCl2 units formed a divergent 3D array (2). Axial ligation of the Sn(IV)-porphyrin building blocks not only alters the supramolecular arrays but also significantly modifies the nanostructures, including porosity, surface area, stability, and morphology. These structural changes consequently affected the photocatalytic degradation efficiency under visible-light irradiation towards acid orange 7 (AO) dye in an aqueous solution. The degradation efficiency of the AO dye in the aqueous solution was observed to be between 86% to 91% within 90 min by these photocatalysts.