Integration of MIL-101-NH2 into Cellulosic Foams for Efficient Cr(VI) Reduction under Visible Light

Nanocellulose-Based Materials for Water Pollutant Removal: A Review

Cellulose in the nano regime, defined as nanocellulose, has been intensively used for water treatment. Nanocellulose can be produced in various forms, including colloidal, water redispersible powders, films, membranes, papers, hydrogels/aerogels, and three-dimensional (3D) objects. They were reported for the removal of water contaminants, e.g., heavy metals, dyes, drugs, pesticides, pharmaceuticals, microbial cells, and other pollutants from water systems. This review summarized the recent technologies for water treatment using nanocellulose-based materials. A scientometric analysis of the topic was also included. Cellulose-based materials enable the removal of water contaminants, and salts offer advanced technologies for water desalination. They are widely used as substrates, adsorbents, and catalysts. They were applied for pollutant removal via several methods such as adsorption, filtration, disinfection, coagulation/flocculation, chemical precipitation, sedimentation, filtration (e.g., ultrafiltration (UF), nanofiltration (NF)), electrofiltration (electrodialysis), ion-exchange, chelation, catalysis, and photocatalysis. Processing cellulose into commercial products enables the wide use of nanocellulose-based materials as adsorbents and catalysts.

Bio-based adsorption foam composed of MOF and polyethyleneimine-modified cellulose for selective anionic dye removal

With the increase of sustainable development goal, the bio-based adsorption materials with high and selective dye removal are important for water treatment in the dyeing industry. In this paper, a bio-based adsorption foam composed of metal-organic frameworks (MOF) and polyethyleneimine (PEI)-modified cellulose was prepared by a three-step process, i.e., PEI modification of cellulose fibers (PC), MOF decoration of PEI-modified cellulose (MIL-53@PC), and in-situ foaming with polyurethane. PEI modification provides cellulose fiber with more active sites for both dye adsorption and MOF bonding. We found that MIL-53 crystals were tightly bonded on the surface of PC through hydrogen bonding. Because of the abundant adsorption sites (e.g., amines, iron oxide group), the MIL-53@PC demonstrated high adsorption capacity and selectivity for anionic dye (e.g., 936.5 mg/g for methyl orange) through electrostatic interaction and hydrogen bonding. Finally, MIL-53@PC particles were blended with a waterborne polyurethane prepolymer to prepare a three-dimensional hydrophilic foam (MIL-53@PC/PUF), which not only maintained high adsorption capacity and selectivity of MIL-53@PC and also improved its recyclability and reusability. The MIL-53@PC/PUF offers a promising solution for dye wastewater treatment.

Simple ultrasonic integration of shapeable, rebuildable, and multifunctional MIL-53(Fe)@cellulose composite for remediation of aqueous contaminants

Metal-organic frames (MOFs) have been recognized as one of the best candidates in the remediation of aqueous contaminants, while the fragile powder shape restricts the practical implementation. In this work, a shapeable, rebuildable, and multifunctional MOF composite (MIL-53@CF) was prepared from MIL-53 (Fe) and cellulose fiber (CF) using a simple ultrasonic method for adsorption and photocatalytic degradation of organic pollutants in wastewater. The results showed MIL-53(Fe) crystals were uniformly growth on CF surfaces and bonded with surface nanofibrils of CF through physical crosslinking and hydrogen bonding. Because of the high bonding strength, the MIL-53@CF composite exhibited an excellent compressive strength (3.53 MPa). More importantly, the MIL-53@CF composite was rebuildable through mechanical destruction followed by re-ultrasonication, suggesting the excellent reusability of MIL-53@CF for water remediation. The MIL-53@CF composite also had high adsorption capacities for methyl orange (884.6 mg·g-1), methylene blue (198.3 mg·g-1), and tetracycline (106.4 mg·g-1). MIL-53@CF composite could degrade TC through photocatalysis. The photocatalytic degradation mechanism was attributed to the Fe(II)/Fe(III) transform cycle reaction of MIL-53 crystal located on MIL-53@CF. Furthermore, the mechanical property and remoldability of MIL-53@CF composite increased its practicability. Comprehensively, MIL-53@CF composite provided a possible strategy to practically apply MOF in the remediation of aqueous contaminants.

MIL-101-NH2(Fe)-Coated Nylon Microfibers for Immobilized Photocatalysts in RhB and Cr(VI) Removal

MIL-101-NH₂(Fe) is one of the effective photocatalytic metal-organic frameworks (MOFs) working under visible light. However, its powder-type form inhibits reusability in practical applications. In this study, we immobilized MIL-101-NH₂(Fe) on a polymeric microfiber mesh to improve reusability while minimizing the loss of catalytic performance. To overcome the lack of surface functionality of the nylon fibers, an atomic layer deposition Al₂O₃ layer and NH₂-BDC linker were introduced to facilitate uniform coating of the MOF on the fiber surface. The reactions of the metal precursor to the nylon substrate and NH₂-BDC ligand of the MOF allow chemical bonding from the core to the shell of the entire hybrid catalytic materials. The resulting fiber-immobilized MOFs (Nylon@Al₂O₃@MOF) demonstrated high photocatalytic performance in the removal of RhB and Cr(VI) as representatives of organic dyes and heavy metals, respectively, while retaining over 85% of its efficiency after five cycles.

Advances in Application of Cellulose-MOF Composites in Aquatic Environmental Treatment: Remediation and Regeneration

Metal organic frameworks (MOFs) have gained remarkable interest in water treatment due to their fascinating characteristics, such as tunable functionality, large specific surface area, customizable pore size and porosity, and good chemical and thermal stability. However, MOF particles tend to easily agglomerate in nanoscale, thus decreasing their activity and processing convenience. It is necessary to shape MOF nanocrystals into maneuverable structures. The in situ growth or ex situ incorporation of MOFs into inexpensive and abundant cellulose-family materials can be effective strategies for the stabilization of these MOF species, and therefore can make available a range of enhanced properties that expand the industrial application possibilities of cellulose and MOFs. This paper provides a review of studies on recent advances in the application of multi-dimensional MOF-cellulose composites (e.g., aerogels, membranes, and bulk materials) in wastewater remediation (e.g., metals, dyes, drugs, antibiotics, pesticides, and oils) and water regeneration by adsorption, photo- or chemocatalysis, and membrane separation strategies. The advantages brought about by combining MOFs and cellulose are described, and the performance of MOF-cellulose is described and compared to its counterparts. The mechanisms of relative MOF-cellulose materials in processing aquatic pollutants are included. Existing challenges and perspectives for future research are proposed.

Cellulose: A Review of Water Interactions, Applications in Composites, and Water Treatment

Cellulose is known to interact well with water, but is insoluble in it. Many polysaccharides such as cellulose are known to have significant hydrogen bond networks joining the molecular chains, and yet they are recalcitrant to aqueous solvents. This review charts the interaction of cellulose with water but with emphasis on the formation of both natural and synthetic fiber composites. Covering studies concerning the interaction of water with wood, the biosynthesis of cellulose in the cell wall, to its dispersion in aqueous suspensions and ultimately in water filtration and fiber-based composite materials this review explores water-cellulose interactions and how they can be exploited for synthetic and natural composites. The suggestion that cellulose is amphiphilic is critically reviewed, with relevance to its processing. Building on this, progress made in using various charged and modified forms of nanocellulose to stabilize oil-water emulsions is addressed. The role of water in the aqueous formation of chiral nematic liquid crystals, and subsequently when dried into composite films is covered. The review will also address the use of cellulose as an aid to water filtration as one area where interactions can be used effectively to prosper human life.

Immobilization of ZnIn2S4 on sodium alginate foam for efficient hexavalent chromium removal

Photocatalytic technology has been extensively studied in the removal of toxic Cr(VI) from wastewater. However, common powdery photocatalysts suffer from poor recyclability and secondly pollution. Herein, the zinc indium sulfide (ZnIn₂S₄) particles were integrated onto the sodium alginate foam(SA) matrix through a facile way to obtain foam-shape catalyst. Diverse characterization techniques including X-ray diffraction(XRD), Fourier transform infrared(FT-IR), scanning electron microscope(SEM) and X-ray photoelectron spectroscopy(XPS) were employed to reveal the composite compositions, organic-inorganic interface interactions, mechanical property, and pore morphology of the foams. Results demonstrated that the ZnIn₂S₄ crystals wrapped on SA skeleton tightly and constructed a flower-like structure. As-prepared hybrid foam with lamellar structure showed great potential in Cr(VI) treatment due to the presence of macropores and highly available active sites. A maximum Cr(VI) photoreduction efficiency of 93 % were observed over the optimal sample of ZS-1 (with a ZnIn₂S₄:SA mass ratio of 1:1) under visible irradiation. When tested with mixed pollutants (Cr(VI)/dyes), the ZS-1 sample displayed an enhanced removal efficiency of 98 % for Cr(VI) and 100 % for Rhodamine B(RhB). Moreover, the composite maintained prominent photocatalytic performance and a relatively integral 3D structure scaffold after continuous six runs, revealing its superior reusability and durability.

BiVO4-Deposited MIL-101-NH2 for Efficient Photocatalytic Elimination of Cr(VI)

In this study, a flower-like BiVO₄/MIL-101-NH₂ composite is synthesized by a facile and surfactant-free process. The -COO^--Bi³⁺ ionic bond construction was conductive to enhance the interface affinity between BiVO₄ and MIL-101-NH₂. Due to the highly efficient light capture and sufficient electron traps induced by oxygen vacancies and the formation of a heterostructure, the improved separation and transportation rates of charge carriers are realized. In addition, the MIL-101-NH₂/BiVO₄ composite is favorable for Cr(VI) photocatalytic removal (91.2%). Moreover, FNBV-3 (Fe/Bi = 0.25) also exhibited an excellent reusability after five cycles.

The state of the art review on photocatalytic Cr(VI) reduction over MOFs-based photocatalysts: From batch experiment to continuous operation

This state of the art review presented the photocatalytic reduction from highly toxic Cr(VI) to lowly toxic Cr(III) with metal-organic frameworks (MOFs) and their composites. The construction of composites facilitated the transportation of the photo-induced charges to enhance the Cr(VI) reduction, in which the corresponding mechanisms were clarified by both experimental tests and DFT calculations. The immobilized MOFs onto some substrates accomplished continuous operations toward Cr(VI) reduction even under real solar light. As well, the environmental applications of the Cr(VI) reduction were analyzed, in which the influence factors toward the Cr(VI) reduction were clarified. This review reported that a big breakthrough was achieved from the batch experiment to the continuous operation for Cr(VI) reduction, in which MOFs demonstrated a bright prospective in the field of photocatalytic Cr(VI) reduction.

Construction of MIL-125-NH2@BiVO4 Composites for Efficient Photocatalytic Dye Degradation

The design and construction of a photocatalyst with a heterostructure are a feasible and effective way to enhance the catalytic performance. Herein, a specially designed composite based on MIL-125-NH₂ and BiVO₄ was prepared and used for wastewater treatment. In the hybrid MIL-125-NH₂@BiVO₄, MIL-125-NH₂ was uniformly dispersed on the BiVO₄ surface. There is a high affinity between MIL-125-NH₂ and BiVO₄ due to the lattice defects. Under visible light irradiation, the catalytic activity of the as-prepared composite was evaluated by the degradation of various dyes such as malachite green, crystal violet, methylene blue, and Congo red. Nearly 98.7, 99.1, and 41.0% of the initial MG, MB and Cr(VI) were respectively removed over the optical sample of BVTN-5, demonstrating that the hybrid holds great promise for practical applications. Moreover, the composites can be recycled and reused with good stability after five consecutive cycles. The mechanism was proposed and discussed in detail. This work will shed light on the construction of MOF-based composites for efficient photocatalysis.

Visible-Light-Driven Zr-MOF/BiOBr Heterojunction for the Efficient Synchronous Removal of Hexavalent Chromium and Rhodamine B from Wastewater

With the rapid industrial development, the coexistence of multiple pollutants in wastewater has become a common phenomenon. Thus, developing highly efficient decontamination methods is imperative. In this work, a string of UiO-66-NH₂/BiOBr heterojunctions with varying ratios of BiOBr were prepared and applied to remove hexavalent chromium Cr(VI) and rhodamine B (RhB). The possible growth process of BiOBr nanosheets on UiO-66-NH₂, removal activity of contaminants, and photocatalysis mechanism were investigated. When the mass ratio of UiO-66-NH₂ to BiOBr reaches 1:0.75, the heterojunction (NB-75) shows optimal photocatalytic activity. After 30 min of adsorption, the total removal rates of Cr(VI) (50 mg/L) and RhB (10 mg/L) over NB-75 (0.25 g/L) reaches 96.7% within 120 min of illumination and 98.9% within 80 min of illumination, respectively. For the removal process, there are two factors. The first is the high adsorption capacity for RhB and Cr(VI) owing to the high porosity of UiO-66-NH₂ and interlayer surface positive charge of BiOBr. The second is the improved visible-light photocatalytic performance of the UiO-66-NH₂/BiOBr heterojunction via rapid separation of photoinduced carriers. In addition, the active species capture study reveals that the electrons (e^-) and the superoxide radicals (^•O₂ ^-) play key roles in Cr(VI) reduction, while the holes (h⁺) are major reactive groups participating in the degradation of RhB. This work demonstrated a kind of promising MOF-based photocatalysis material for eliminating Cr(VI) and RhB simultaneously.

Synthesis of a Novel Adsorbent Based on Chitosan Magnetite Nanoparticles for the High Sorption of Cr (VI) Ions: A Study of Photocatalysis and Recovery on Tannery Effluents

This study aims to evaluate the functionalization of chitosan biopolymer with heterocyclic moieties of 2-thioxodihydropyrimidine-4,6(1H,5H)-dione used for enhancing the sorption of Cr ions from aqueous solution. A synthesized sorbent is a nanoscale particle (around 5–7 nm), which explains the fast kinetics of sorption. The sorbent is specified using elemental analysis (EA), FTIR, BET (nitrogen sorption desorption isotherms), TGA, and SEM-EDX analyses. Sorption properties are investigated using ultraviolet emission (UV) but also using visible light (L). In the sorption diagram, the high sorption uptake and fast kinetics observed using ultraviolet conditions are shown. This work is conducted by removing Cr ions from highly contaminated tannery effluents, which have a high concentration of Cr associated with other poisonous elements such as Cd(II) and Pb(II). Under the selected conditions, complete sorption is performed during the first 60 and 45 min with a capacity of 2.05 and 2.5 mmol Cr g−1 for the crosslinked chitosan (without functionalization) in L and UV, respectively. This sorption is enhanced by functionalizing to 5.7 and 6.8 mmol Cr g−1 at the L and UV, respectively, as well as improving the sorption kinetics to 35 and 30 min for both techniques, respectively. The PFORE, and (Langmuir and Sips equations) fit the kinetics and isotherms, respectively.

Recent Progress in the Development of MOF-Based Photocatalysts for the Photoreduction of Cr(VI)

There has been a direct correlation between the rate of industrial development and the spread of pollution on Earth, particularly in the last century. The organic and inorganic pollutants generated from industrial activities have created serious risks to human life and the environment. The concept of sustainability has emerged to tackle the environmental issues in developing chemical-based industries. However, pollutants have continued to be discharged to water resources, and finding appropriate techniques for the removal and remedy of wastewater is in high demand. Chromium is one of the high-risk heavy metals in industrial wastewaters that should be removed via physical adsorption and/or transformed into less hazardous chemicals. Photocatalysis as a sustainable process has received considerable attention as it utilizes sunlight irradiation to remedy Cr^(VI) via a cost-effective process. Numerous photocatalytic systems have been developed up to now, but metal-organic frameworks (MOFs) have gained growing attention because of their unique versatilities and facile structural modulations. A variety of MOF-based photocatalysts have been widely employed for the photoreduction of Cr^(VI). Here, we review the recent progress in the design of MOF photocatalysts and summarize their performance in photoreduction reactions.

Cellulose-Based Materials for Water Remediation: Adsorption, Catalysis, and Antifouling

Cellulose-based materials have been advanced technologies that used in water remediation. They exhibit several advantages being the most abundant biopolymer in nature, high biocompatibility, and contain several functional groups. Cellulose can be prepared in several derivatives including nanomaterials such as cellulose nanocrystals (CNCs), cellulose nanofibrils (CNFs), and TEMPO (2,2,6,6-tetramethylpiperidine-1-oxyl radical)-mediated oxidized cellulose nanofibrils (TOCNF). The presence of functional groups such as carboxylic and hydroxyls groups can be modified or grafted with organic moieties offering extra functional groups customizing for specific applications. These functional groups ensure the capability of cellulose biopolymers to be modified with nanoparticles such as metal-organic frameworks (MOFs), graphene oxide (GO), silver (Ag) nanoparticles, and zinc oxide (ZnO) nanoparticles. Thus, they can be applied for water remediation via removing water pollutants including heavy metal ions, organic dyes, drugs, and microbial species. Cellulose-based materials can be also used for removing microorganisms being active as membranes or antibacterial agents. They can proceed into various forms such as membranes, sheets, papers, foams, aerogels, and filters. This review summarized the applications of cellulose-based materials for water remediation via methods such as adsorption, catalysis, and antifouling. The high performance of cellulose-based materials as well as their simple processing methods ensure the high potential for water remediation.