Efficient Demulsification of Diesel-in-Water Emulsions by Different Structural Dendrimer-Based Demulsifiers

Understanding Separation of Oil-Water Emulsions by High Surface Area Polymer Gels Using Experimental and Simulation Techniques

This work examines the functional dependence of the efficiency of separation of oil-water emulsions on surfactant adsorption abilities of high surface area polymer gels. The work also develops an understanding of the factors and steps that are involved in emulsion separation processes using polymer gels. The work considers four polymer gels offering different surface energy values, namely, syndiotactic polystyrene (sPS), polyimide (PI), polyurea (PUA), and silica. The data reveal that surfactant adsorption abilities directly control the emulsion separation performance. The gels of sPS and PI destabilize the emulsions due to significant surfactant adsorption. The surfactant-lean oil droplets are then absorbed in the pores of sPS and PI gels due to the preferential wettability of the oil phase. The PUA and silica gels are more hydrophilic and show a lower surfactant adsorption ability. These gels cannot effectively remove the surfactant molecules from the emulsions, leading to a poor emulsion separation performance. The study uses simulation data to understand the adsorption characteristics of two poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) block copolymer surfactants. The simulation results are used for the interpretation of emulsion separation performance by the gels.

Study on the structure-activity relationship of cationic polyacrylates for the treatment of oilfield produced water

Cationic polyacrylates exhibit both reverse demulsification and flotation performance, which can avoid incompatibility between the reverse demulsifier and flotation agent during treatment of produced water from offshore oilfields. In our previous work, the effect of the structure of the cationic unit on the reverse demulsification and flotation performance of cationic polyacrylates was studied. However, the structure-activity relationship of cationic polyacrylates has not been systematically studied. In this study, the relationships between the structure (acrylate type, tertiary amine type, mass ratio of acrylate to tertiary amine, and degree of cationicity), interfacial properties (surface tension, interfacial tension, zeta potential, interfacial elastic modulus, interaction force between oil droplets, and film drainage time of an oil-covered bubble), and reverse demulsification and flotation performance of cationic polyacrylates were investigated. A reduction in the elastic modulus of the oil-water interface was the key factor for good reverse demulsification performance, whereas a decrease in the film drainage time of an oil-covered bubble was the key factor for good flotation performance. Ethyl acrylate (EA) was superior to methyl acrylate (MA), and dimethylaminopropyl methacrylamide (DPM) was superior to dimethylaminoethyl methacrylate (DEM). Increases in the mass ratio of ethyl acrylate to dimethylaminopropyl methacrylamide and the degree of cationicity were beneficial for reducing the elastic modulus of the oil-water interface and the film drainage time of an oil-covered bubble. This is the first time that the structure-property-performance relationship of cationic polyacrylates has been systematically studied. A cationic polyacrylate that exhibited both good reverse demulsification performance and good flotation performance is recommended.

Synthesis and application of recyclable magnetic cellulose nanocrystals for effective demulsification of water in crude oil emulsions

The development of eco-friendly, efficient, and economical demulsifiers for the demulsification of water in crude oil emulsion is one of the important issues in the petroleum industry. Demulsifiers with suitable performance in several demulsification methods are good choices for effective and economical demulsification. In this study, recyclable magnetic cellulose nanocrystals have been synthesized from cotton by a simple method and used in the demulsification of water in crude oil emulsions. Chemical and magnetic demulsification by magnetic cellulose nanocrystals has been investigated. In addition, the effects of time, temperature, and demulsifier concentration on the demulsification efficiency have been evaluated. According to the results, this demulsifier can be used as an effective demulsifier for both chemical and magnetic demulsification and displayed a demulsification efficiency of 100 % at 50 °C without a magnet and 90 % at 20 °C with a magnet. The chemical demulsification efficiency of Fe3O4 nanoparticles was investigated and it showed lower DE compared to magnetic cellulose nanocrystals. The recyclability tests of the demulsifier indicated that magnetic cellulose nanocrystals can be used up to 4 times. Finally, the demulsification mechanism and interfacial tension measurements revealed that this demulsifier reduced the interfacial tension between water and crude oil and increased the water droplet sizes.

Switchable Pickering Emulsions Stabilized via Synergistic Nanoparticles-Superamphiphiles Effects and Rapid Response to CO2/N2

A CO2/N2-responsive emulsion provides milder reaction conditions, nontoxicity, and economic feasibility compared to other switchable surfactants. In this study, CO2/N2-responsive pickering emulsions were fabricated by using a compounded dispersion containing SiO2 nanoparticles (NPs) and superamphiphiles as the emulsifying agents. The synergistic effects of the SiO2 NPs and superamphiphiles significantly stabilized the emulsion at all of the tested concentrations and prevented complete phase separation of oil and water. The electrostatic interaction between the SiO2 NPs and superamphiphiles was disrupted after bubbling with CO2 for 30 s, resulting in the breaking of the emulsion. However, the dispersion recovered its interfacial activity after the introduction of N2 and again emulsified the emulsion. This reversible switching behavior was validated through three consecutive cycles of bubbling CO2/N2. The protonation and deprotonation of the SiO2 NPs and superamphiphiles in response to CO2/N2 facilitated reversible assembly and disassembly, which enabled the switching of the emulsions between inactive and active forms. The novel highly stable Pickering emulsions demonstrated rapid demulsification and emulsification in response to CO2/N2 and are promising for a wide range of applications.

Sequential Demulsification through the Hydrophobic-Hydrophilic-Hydrophobic Filtration Layer toward High-Performing Oil Recovery

Demulsification using membranes is a promising method to coalesce highly stable emulsified oil droplets for oil recovery. Nevertheless, a structure of the current filtration medium that is not efficient for oil droplet coalescence impedes rapid permeability, thereby inevitably restricting their practical applications. Herein, we report a hydrophobic-hydrophilic-hydrophobic (3H) demulsification medium that exhibits a benchmark permeability of ∼2.1 × 104 L m-2 h-1 with a demulsification efficiency of >98.0%. Remarkably, this 3H demulsification medium maintains over 90% demulsification efficiency in the oil-in-water (O/W) emulsions with a wide range of surfactant concentrations, which shows excellent applicability. Based on the combined results of quasi situ microscope images and molecular dynamics simulations, we show that the polydimethylsiloxane-modified hydrophobic layer facilitates the capture and coalescence of oil droplets, the hydrophilic inner layer assists in squeezing the coalescence of enlarged droplets, and the third hydrophobic layer accelerates the discharge of demulsified oil to sustain permeability. The sequential demulsification mechanism between this 3H filtration layer provides a general guide for designing a demulsifying membrane with high demulsification efficiency and high flux toward oil recovery.

Intrafibrillar mineralization of type I collagen by micelle-loaded amorphous calcium phosphate nanoparticles

Mineralization of type I collagen fibrils is highly desired for artificial bone preparation and teeth repairing. Generally, amorphous calcium phosphate (ACP) combined with non-collagenous protein analogue (NCPA) were used for biomimetic remineralization of collagen fibrils. However, the ACP was likely to aggregate to form larger particles that could not infiltrate into the gaps of the collagen for intrafibrillar mineralization, and the poor storage stability of ACP has challenged its practical applications. To address this question, here we assembled ACP that was stabilized by carboxylated polyamidoamine (CPAMAM) at a pH of 6.5 to form dispersed nanoparticles of 25 nm in size, which was named as ACP/CPAMAM. The ACP/CPAMAM nanoparticles were further loaded into micelles composed of polysorbate and polyethylene glycol (PEG) to further improve their storage stability. The micelle-loaded ACP/CPAMAM particles could maintain their amorphous phase after storage for 12 months. During the mineralization of collagen fibrils, isopropanol (IPA) was introduced to dissolve the micelles and release the ACP/CPAMAM nanoparticles. By using micelle-loaded ACP/CPAMAM, good intrafibrillar mineralization of type I collagen was demonstrated. This work provides novel methods for preparing ACP nanoparticles with good storage stability and controllable release for intrafibrillar mineralization.

Novel polymer nanoparticles with core-shell structure for breaking asphaltenes-stabilized W/O and O/W emulsions

HYPOTHESIS

The removal of stable water-in-oil (W/O) or oil-in-water (O/W) emulsions has been a challenging issue in chemical and oil industry for decades. Traditional demulsifiers were generally designed specifically for treating either W/O or O/W emulsions. A demulsifier that is effective for treating both types of emulsions will be highly desired.

EXPERIMENTS

Novel polymer nanoparticles (PBM@PDM) was synthesized as a demulsifier for treating both W/O and O/W emulsions prepared by toluene, water, and asphaltenes. The morphology and chemical composition of synthesized PBM@PDM were characterized. Demulsification performance and interaction mechanisms including interfacial tension, interfacial pressure, surface charge properties and surface forces were systematically studied.

FINDINGS

PBM@PDM could immediately prompt the coalescence of water droplets upon addition and effectively release the water in asphaltenes-stabilized W/O emulsion. In addition, PBM@PDM successfully destabilized asphaltenes-stabilized O/W emulsion. Not only could PBM@PDM substitute the asphaltenes adsorbed at the water-toluene interface, but they could also dominate the water-toluene interfacial pressure in competition with asphaltenes. The steric repulsion between interfacial asphaltene films could be suppressed in the presence of PBM@PDM. Surface charges significantly influenced the stability of asphaltenes-stabilized O/W emulsion. This work provides useful insights into the interaction mechanisms of asphaltene-stabilized W/O and O/W emulsions.

Investigation of Dioctyl Sodium Sulfosuccinate in Demulsifying Crude Oil-in-Water Emulsions

This research investigated the performance of dioctyl sodium sulfosuccinate (DSS), a double-chain anionic surfactant, in breaking crude oil-in-water emulsions. The response surface methodology was used to consider the effect of the DSS concentration, oil concentration, and shaking time on demulsification efficiency and obtain optimum demulsification conditions. Further single-factor experiments were conducted to investigate the effects of salinity, crude oil conditions (fresh and weathered), and gravity separation settling time. The results showed that DSS efficiently demulsified stable emulsions under different oil concentrations (500-3000 mg/L) within 15 min shaking time. Increasing DSS concentration to 900 mg/L (critical micelle concentration) increased the demulsification efficiency to 99%. DSS not only improved the demulsification efficiency but also did not impede the demulsifier interfacial adsorption at the oil-water interface due to the presence of the double-chain structure. The low molecular weight enables the homogeneous distribution of DSS molecules in the emulsion, leading to a high demulsification efficiency within 15 min. Analysis of variance results indicated the importance of considering the interaction of oil concentration and shaking time in demulsification. DSS could reduce the total extractable petroleum hydrocarbons in the separated water to <10 mg/L without gravity separation and could achieve promising demulsification performance at high salinity (36 g/L) and various concentrations of fresh and weathered oil. The demulsification mechanism was explained by analyzing the microscopic images and the transmittance of the emulsion. DSS could be an efficient double-chain anionic surfactant in demulsifying stable oil-in-water emulsions.

Development of advanced oil/water separation technologies to enhance the effectiveness of mechanical oil recovery operations at sea: Potential and challenges

Mechanical oil recovery (i.e., booming and skimming) is the most common tool for oil spill response. The recovered fluid generated from skimming processes may contain a considerable proportion of water (10 % ~ 70 %). As a result of regulatory prohibition on the discharge of contaminated waters at sea, vessels and/or storage barges must make frequent trips to shore for oil-water waste disposal. This practice can be time- consuming thus reduces the overall efficiency and capacity of oil recovery. One potential solution is on-site oil-water separation and disposal of water fraction at sea. However, currently available decanting processes may have limited oil/water separation capabilities, especially in the presence of oil-water emulsion, which is inevitable in mechanical oil recovery. The decanted water may not meet the discharge standards and cause severe ecotoxicological impacts. This paper therefore comprehensively reviews the principles and progress in oil/water separation, demulsification, and on-site treatment technologies, investigates their applicability on decanting at sea, and discusses the ecotoxicity of decanted water in the marine environment. The outputs provide the fundamental and practical knowledge on decanting and help enhance response effectiveness and consequently reducing the environmental impacts of oil spills.

Demulsification of Heavy Oil-in-Water Emulsion by a Novel Janus Graphene Oxide Nanosheet: Experiments and Molecular Dynamic Simulations

Various nanoparticles have been applied as chemical demulsifiers to separate the crude-oil-in-water emulsion in the petroleum industry, including graphene oxide (GO). In this study, the Janus amphiphilic graphene oxide (JGO) was prepared by asymmetrical chemical modification on one side of the GO surface with n-octylamine. The JGO structure was verified by Fourier-transform infrared spectra (FTIR), transmission electron microscopy (TEM), and contact angle measurements. Compared with GO, JGO showed a superior ability to break the heavy oil-in-water emulsion with a demulsification efficiency reaching up to 98.25% at the optimal concentration (40 mg/L). The effects of pH and temperature on the JGO’s demulsification efficiency were also investigated. Based on the results of interfacial dilatational rheology measurement and molecular dynamic simulation, it was speculated that the intensive interaction between JGO and asphaltenes should be responsible for the excellent demulsification performance of JGO. This work not only provided a potential high-performance demulsifier for the separation of crude-oil-in-water emulsion, but also proposed novel insights to the mechanism of GO-based demulsifiers.

A critical review of the development and demulsification processes applied for oil recovery from oil in water emulsions

The formation of stable emulsions is a fundamental problem in oil industry that can result in a sequence of environmental and operational problems. Chemical demulsification is extensively applied for the recovery of oil from water as well as water from oil. This review introduces different chemical demulsifiers applied for the demulsification and recovery of oil from oil in water (O/W) emulsions. Main types of surfactants (anionic, cationic, nonionics and amphoteric) involved in the formation of emulsions and enhances their stability were discussed. Promising demulsifiers such as nanoparticle (NP), hyperbranched polymers, and ionic liquids (IL), which achieved high oil recovery rate, parameters influencing demulsification efficiency and demulsification mechanisms were explored. Lastly, improvements, challenges, and new changes being made to chemical demulsifiers were underlined. Functionalized magnetic nanoparticles and hyperbranched polymers were very effective in recovering oil from O/W emulsions with an efficiency >95%. Polymers with highly hydrophilic content and high molecular weight can achieve excellent oil recovery rates due to higher interfacial activity, higher dispersion, and presence of specific functional groups. Although ionic liquids could achieve oil recovery up to 90%, high cost limits their applications. NPs showed excellent oil recovery behavior at low concentrations and ambient temperature. Demulsification efficiency of NPs can be enhanced by functionalize with other components (e.g., polymers and surfactants), while service life can be extend by silica coating. Future challenges include scaling up the use of NPs in oil recovery process and highlighting contrasts between lab-scale and field-scale applications.

Emulsion-Templated, Magnetic, Hydrophilic-Oleophobic Composites for Controlled Water Removal

Emulsion-templated, hydrophilic-oleophobic porous materials are promising for the removal of a small amount of water from oil-water mixtures, but the maneuver and complete collection of these porous materials are challenging. Herein, we report the fabrication of magnetic, hydrophilic-oleophobic polyHIPE composites from reactive Fe₃O₄ nanoparticle-stabilized high internal phase emulsions through simultaneous bulk polymerization of water-soluble monomers and interface-catalyzed polycondensation of 1H,1H,2H,2H-perfluorooctyltriethoxysilane. The resulting composites were hydrophilic-oleophobic, with water droplets rapidly absorbed (within 20 s), and exhibited designable magnetic responsiveness. The hydrophilicity-oleophobicity enabled water to be removed through selective absorption from oil-water mixtures (including surfactant-stabilized water-in-oil emulsions), with a high separation rate over 99%. The magnetic-responsiveness enabled both the dry and the swollen composites to be maneuvered in a remote and contactless manner and to be fully collected. Therefore, the magnetic, hydrophilic-oleophobic polyHIPE composites are excellent candidates for the removal of water from water-oil mixtures with complete collection.

Demulsification of water-in-crude oil emulsion driven by a carbonaceous demulsifier from natural rice husks

Removing emulsified water from a water-in-crude oil (W/O) emulsion is critically required prior to downstream processing in the petroleum industry. In this work, environmentally friendly and amphipathic rice husk carbon (RHC) demulsifier was prepared by a simple carbonization process in a muffle furnace using rice husks as starting materials. RHC was characterized by field-emission scanning electron microscope, energy dispersive spectrometer, Fourier transform infrared spectrometer, ultraviolet-visible spectrometer, powder X-ray diffraction, zeta potential and synchronal thermal analyzer. The factors such as dosage, temperature, settling time, pH value and salinity were systematically investigated. The results indicated that the dehydration efficiency (DE) reached as high as 96.99% with 600 mg/L of RHC for 80 min at 70 °C. RHC exhibited an optimal DE under neutral condition, but it was also effective under acidic and alkaline conditions. Also, it had an excellent salt tolerance. The possible demulsification mechanism was explored by interfacial properties, different treatment methods for RHC and microexamination. The demulsification of RHC is attributed to its high interfacial activity, oxygen-containing groups and content of silica. It indicates that RHC is an effective demulsifier for the treatment of the W/O emulsion.

Emulsion-templated porous polymers: drying condition-dependent properties

Macroporous materials templated using high internal phase emulsions (HIPEs) are promising for various applications. To date, new strategies to create emulsion-templated porous materials and to tune their properties (especially wetting properties) are still highly required. Here, we report the fabrication of macroporous polymers from oil-in-water HIPEs, bereft of conventional monomers and crosslinking monomers, by simultaneous ring-opening polymerization and interface-catalyzed condensation, without heating or removal of oxygen. The resulting macroporous polymers showed drying condition-dependent wetting properties (e.g., hydrophilicity-oleophilicity from freezing drying, hydrophilicity-oleophobicity from vacuum drying, and amphiphobicity from heat drying), densities (from 0.019 to 0.350 g cc^-1), and compressive properties. Hydrophilic-oleophilic and amphiphobic porous polymers turned hydrophilic-oleophobic simply by heating and protonation, respectively. The hydrophilic-oleophobic porous polymers could remove a small amount of water from oil-water mixtures (including surfactant-stabilized water-in-oil emulsions) by selective absorption and could remove water-soluble dyes from oil-water mixtures. Moreover, the transition in wetting properties enabled the removal of water and dyes in a controlled manner. The feature that combines simply preparation, tunable wetting properties and densities, robust compression, high absorption capacity (rate) and controllable absorption makes the porous polymers to be excellent candidates for the removal of water and water-soluble dyes from oil-water mixtures.

Application of Ionic Liquids for Chemical Demulsification: A Review

In recent years, ionic liquids have received increasing interests as an effective demulsifier due to their characteristics of non-flammability, thermal stability, recyclability, and low vapor pressure. In this study, emulsion formation and types, chemical demulsification system, the application of ionic liquids as a chemical demulsifier, and key factors affecting their performance were comprehensively reviewed. Future challenges and opportunities of ionic liquids application for chemical demulsification were also discussed. The review indicted that the demulsification performance was affected by the type, molecular weight, and concentration of ionic liquids. Moreover, other factors, including the salinity of aqueous phase, temperature, and oil types, could affect the demulsification process. It can be concluded that ionic liquids can be used as a suitable substitute for commercial demulsifiers, but future efforts should be required to develop non-toxic and less expensive ionic liquids with low viscosity, and the demulsification efficiency could be improved through the application of ionic liquids with other methods such as organic solvents.

The Demulsification Properties of Cationic Hyperbranched Polyamidoamines for Polymer Flooding Emulsions and Microemulsions

Polymer flooding emulsions and microemulsions caused by tertiary oil recovery technologies are harmful to the environment due to their excellent stability. Two cationic hyperbranched polyamidoamines (H-PAMAM), named as H-PAMAM-HA and H-PAMAM-ETA, were obtained by changing the terminal denotation agents to H-PAMAM, which was characterized by 1H NMR, FT-IR, and amine possession, thereby confirmed the modification. Samples (300 mg/L) were added to the polymer flooding emulsion (1500 mg/L oil concentration) at 30 °C for 30 min and the H-PAMAM-HA and H-PAMAM-ETA were shown to perform at 88% and 91% deoil efficiency. Additionally, the increased settling time and the raised temperature enhanced performance. For example, an oil removal ratio of 97.7% was observed after dealing with the emulsion for 30 min at 60 °C, while 98.5% deoil efficiency was obtained after 90 min at 45 °C for the 300 mg/L H-PAMAM-ETA. To determine the differences when dealing with the emulsion, the interfacial tension, ζ potential, and turbidity measurements were fully estimated. Moreover, diametrically different demulsification mechanisms were found when the samples were utilized to treat the microemulsion. The modified demulsifiers showed excellent demulsification efficiency via their obvious electroneutralization and bridge functions, while the H-PAMAM appeared to enhance the stability of the microemulsion.

Amphiphobic polyHIPEs with pH-triggered transition to hydrophilicity–oleophobicity for the controlled removal of water from oil–water mixtures

Amphiphobic polyHIPEs with pH-triggered transition to hydrophilicity–oleophobicity were templated from high internal phase emulsions for the controlled removal of water from oil–water mixtures.

An Overview of Recent Advances in State-of-the-Art Techniques in the Demulsification of Crude Oil Emulsions

The processing of crude oil often requires the extraction of a large amount of water. Frequently, crude oil is mixed with water to form water-in-crude oil emulsions as the result of factors such as high shear at the production wellhead and surface-active substances that are naturally present in crude oil. These emulsions are undesirable and require demulsification to remove the dispersed water and associated inorganic salts in order to meet production and transportation specifications. Additionally, the demulsification of these crude oil emulsions mitigates corrosion and catalyst poisoning and invariably maximizes the overall profitability of crude oil production. Recently, there has been growing research interest in developing workable solutions to the difficulties associated with transporting and refining crude oil emulsions and the restrictions on produced water discharge. Therefore, this paper reviews the recent research efforts on state-of-the-art demulsification techniques. First, an overview of crude oil emulsion types, formation, and stability is presented. Then, the parameters and mechanisms of emulsification formation and different demulsification techniques are extensively examined. It is worth noting that the efficiency of each of these techniques is dependent on the operating parameters and their interplay. Moreover, a more effective demulsification process could be attained by leveraging synergistic effects by combining one or more of these techniques. Finally, this literature review then culminates with propositions for future research. Therefore, the findings of this study can help for a better understanding of the formation and mechanisms of the various demulsification methods of crude oil to work on the development of green demulsifiers by different sources.

Efficient Demulsification of Acidic Oil-In-Water Emulsions with Silane-Coupled Modified TiO2 Pillared Montmorillonite

Emulsified pickling waste liquid, derived from cleaning oily hardware, cause serious environmental and ecological issues. In this work, a series of grafted (3-aminopropyl)triethoxysilane (APTES) TiO2 pillared montmorillonite (Mt), Ti-Mt-APTES, are prepared and characterized for their assessment in demulsification of acidic oil-in-water emulsion. After titanium hydrate is introduced through ion exchange, montmorillonite is modified by hydrophobic groups coming from APTES. The Ti-Mt-APTES in acidic oil-in-water emulsion demulsification performance and mechanism are studied. Results show that the prepared Ti-Mt-APTES has favorable demulsification performance. The Ti-Mt-APTES demulsification efficiency (ED) increased to an upper limit value when the mass ratio of APTES to the prepared TiO2 pillared montmorillonite (Ti-Mt) (RA/M) was 0.10 g/g, and the 5 h is the optimal continuous stirring time for breaking the acidic oil-in-water emulsion by Ti-Mt-APTES. The ED increased to 94.8% when 2.5 g/L of Ti-Mt-APTES is added into the acidic oil-in-water emulsion after 5 h. An examination of the demulsification mechanism revealed that amphiphilicity and electrostatic interaction both played vital roles in oil-in-water separation. It is demonstrated that Ti-Mt-APTES is a promising, economical demulsifier for the efficient treatment of acidic oil-in-water emulsions.

Mechanisms, performance optimization and new developments in demulsification processes for oil and gas applications

The present review discusses new developments and optimization of demulsification processes in oil and gas applications, and highlights the critical parameters. Discussed are the primary mechanisms of demulsification, as well as the strategies for developing optimum demulsifiers. Demulsification mechanisms are presented in the context of emulsion stability principles which are equally applicable to the destabilization of crude oil-water emulsions. The present paper is a concise overview of the various surfactant classes and their structure-activity relationship. It correlates demulsification optimization with surfactant properties and their applications. These classes include, but are not limited to pluronic block co-polymers, as well as amine- and siloxane based nonionic surfactants. The emphasis is on providing some strategies for achieving optimum crude oil-water separation efficiency by tuning the demulsifier to the intended application and crude oil properties. A brief overview of unconventional analytical techniques, which reach beyond the standard demulsifier evaluation methods, i.e., Near Infrared Spectroscopy (NIR), and in particular, low resolution NMR relaxometry, highlights their role in monitoring demulsification processes.

Demulsification of heavy oil-in-water emulsions by reduced graphene oxide nanosheets

The purpose of this work is to investigate the relationship between the chemical structure of the GO materials and the demulsification performance.