Optimization of the in Situ Pretreatment of High Temperature Ni–Cr Alloys for Ethane Steam Cracking

Opportunities and challenges for the application of post-consumer plastic waste pyrolysis oils as steam cracker feedstocks: To decontaminate or not to decontaminate?

Thermochemical recycling of plastic waste to base chemicals via pyrolysis followed by a minimal amount of upgrading and steam cracking is expected to be the dominant chemical recycling technology in the coming decade. However, there are substantial safety and operational risks when using plastic waste pyrolysis oils instead of conventional fossil-based feedstocks. This is due to the fact that plastic waste pyrolysis oils contain a vast amount of contaminants which are the main drivers for corrosion, fouling and downstream catalyst poisoning in industrial steam cracking plants. Contaminants are therefore crucial to evaluate the steam cracking feasibility of these alternative feedstocks. Indeed, current plastic waste pyrolysis oils exceed typical feedstock specifications for numerous known contaminants, e.g. nitrogen (∼1650 vs. 100 ppm max.), oxygen (∼1250 vs. 100 ppm max.), chlorine (∼1460vs. 3 ppm max.), iron (∼33 vs. 0.001 ppm max.), sodium (∼0.8 vs. 0.125 ppm max.)and calcium (∼17vs. 0.5 ppm max.). Pyrolysis oils produced from post-consumer plastic waste can only meet the current specifications set for industrial steam cracker feedstocks if they are upgraded, with hydrogen based technologies being the most effective, in combination with an effective pre-treatment of the plastic waste such as dehalogenation. Moreover, steam crackers are reliant on a stable and predictable feedstock quality and quantity representing a challenge with plastic waste being largely influenced by consumer behavior, seasonal changes and local sorting efficiencies. Nevertheless, with standardization of sorting plants this is expected to become less problematic in the coming decade.

Effect of Phosphine on Coke Formation during Steam Cracking of Propane

In conventional steam cracking feedstocks, contaminants such as sulfur, phosphine, and heavy metal components, present in trace levels, are believed to affect coke formation on high temperature alloys. To gain an understanding of the role of phosphine coking rates on 25/35, CrNi and Al-containing reactor materials were determined in a plug flow reactor during cracking of a propane feedstock doped with ppb levels of PH₃ in the presence of DMDS. The presence of phosphine decreased the asymptotic coking rates by more than 20%, while it had a smaller influence on the catalytic coking rate. The coking rate was more severely reduced for the 25/35 CrNi alloy in comparison to the Al-containing alloy. The ppm levels of phosphine did not affect the olefin yields nor the production of undesired carbon monoxide. The morphology of the coked alloys were studied using an off-line Scanning Electron Microscope with Energy Dispersive X-ray detector (SEM with EDX) images of coked coupons. Two types of coke morphology are observed, i.e., filamentous coke with DMDS as an additive and globular coke in the presence of phosphine. The effect of phosphine on the material has a positive impact on the oxide scale homogeneity of 25/35 CrNi alloy, whereas the Al-containing alloy remained unchanged.

Catalytic conversion of ethane to valuable products through non-oxidative dehydrogenation and dehydroaromatization

Chemical utilization of ethane to produce valuable chemicals has become especially attractive since the expanded utilization of shale gas in the United States and associated petroleum gas in the Middle East. Catalytic conversion to ethylene and aromatic hydrocarbons through non-oxidative dehydrogenation and dehydroaromatization of ethane (EDH and EDA) are potentially beneficial technologies because of their high selectivity to products. The former represents an attractive alternative to conventional thermal cracking of ethane. The latter can produce valuable aromatic hydrocarbons from a cheap feedstock. Nevertheless, further progress in catalytic science and technology is indispensable to implement these processes beneficially. This review summarizes progress that has been achieved with non-oxidative EDH and EDA in terms of the nature of active sites and reaction mechanisms. Briefly, platinum-, chromium- and gallium-based catalysts have been introduced mainly for EDH, including effects of carbon dioxide co-feeding. Efforts to use EDA have emphasized zinc-modified MFI zeolite catalysts. Finally, some avenues for development of catalytic science and technology for ethane conversion are summarized.

Symoens S, Olahova N, Reyniers MF, B. Marin G, M. Van Geem K. Alumina-based Coating for Coke Reduction in Steam Crackers

Alumina-based coatings have been claimed as being an advantageous modification in industrial ethylene furnaces. In this work, on-line experimentally measured coking rates of a commercial coating (CoatAlloy™) have pointed out its superiority compared to an uncoated reference material in an electrobalance set-up. Additionally, the effects of presulfiding with 500 ppmw DMDS per H₂O, continuous addition of 41 ppmw S per HC of DMDS, and a combination thereof were evaluated during ethane steam cracking under industrially relevant conditions (T_gasphase = 1173 K, P_tot = 0.1 MPa, X_C2H6 = 70%, dilution δ = 0.33 kg_H2O/kg_HC). The examined samples were further evaluated using online thermogravimetry, scanning electron microscopy and energy diffractive X-ray for surface and cross-section analysis together with X-ray photoelectron spectroscopy and wavelength-dispersive X-ray spectroscopy for surface analysis. The passivating coating illustrated a better performance than the reference Ni-Cr Fe-base alloy after application of an improved pretreatment, followed by piddling changes on the product distribution. Presulfiding of the coating affected negatively the observed coking rates in comparison with the reference alloy, so alternative presulfiding and sulfur addition strategies are recommended when using this barrier coating.

Evaluation of a Ti-Base Alloy as Steam Cracking Reactor Material

Low-coking reactor material technologies are key for improving the performance and sustainability of steam crackers. In an attempt to appraise the coking performance of an alternative Ti-base alloy during ethane steam cracking, an experimental study was performed in a jet stirred reactor under industrially relevant conditions using thermogravimetry (T_gasphase = 1173 K, P_tot = 0.1 MPa, X_C2H6 = 70%, and dilution δ = 0.33 kg_H2O/kg_HC). Initially, a typical pretreatment used for Fe-Ni-Cr alloys was utilized and compared with a pretreatment at increased temperature, aiming at better surface oxidation and thus suppressing coke formation. The results revealed a decrease in coking rates upon high temperature pretreatment of the Ti-base alloy, however, its coking performance was significantly worse compared to the typically used Fe-Ni-Cr alloys, and carbon oxides formation increased by a factor of 30 or more. Moreover, the analyzed coupons showed crack propagation after coking/decoking and cooling down to ambient temperature. Scanning electron microscopy combined with energy-dispersive X-ray spectroscopy indicated that the prompt and unsystematic oxidation of the surface and bulk caused observable crack initiation and propagation due to alloy brittleness. Hence, the tested Ti-base alloy cannot be considered an industrially noteworthy steam cracking reactor alloy.

Effect of Long-Term High Temperature Oxidation on the Coking Behavior of Ni-Cr Superalloys

The service time of an industrial cracker is strongly dependent on the long-term coking behavior and microstructure stability of the reactor coil alloy. Super alloys are known to withstand temperatures up to even 1400 K. In this work, several commercially available alloys have been first exposed to a long term oxidation at 1423 K for 500 h, so-called metallurgic aging. Subsequently, their coking behavior was evaluated in situ in a thermogravimetric setup under ethane steam cracking conditions (T_gasphase = 1173 K, P_tot = 0.1 MPa, X_C2H6 = 70%, continuous addition of 41 ppmw S/HC of DMDS, dilution δ = 0.33 kg_H2O/kg_HC) and compared with their unaged coking behavior. The tested samples were also examined using scanning electron microscopy and energy diffractive X-ray for surface and cross-section analysis. The alloys characterized by increased Cr-Ni content or the addition of Al showed improved stability against bulk oxidation and anti-coking behavior after application of metallurgic aging due to the formation of more stable oxides on the top surface.

Shale Gas Implications for C2-C3 Olefin Production: Incumbent and Future Technology

Substantial natural gas liquids recovery from tight shale formations has produced a significant boon for the US chemical industry. As fracking technology improves, shale liquids may represent the same for other geographies. As with any major industry disruption, the advent of shale resources permits both the chemical industry and the community an excellent opportunity to have open, foundational discussions on how both public and private institutions should research, develop, and utilize these resources most sustainably. This review summarizes current chemical industry processes that use ethane and propane from shale gas liquids to produce the two primary chemical olefins of the industry: ethylene and propylene. It also discusses simplified techno-economics related to olefins production from an industry perspective, attempting to provide a mutually beneficial context in which to discuss the next generation of sustainable olefin process development.