Synthesis and CO2 Capture Behavior of Porous Cross-Linked Polymers Containing Pendant Triazole Groups

Triazole-Functionalized Mesoporous Materials Based on Poly(styrene-block-lactic acid): A Morphology Study of Thin Films

We report the synthesis of poly(styrene-block-lactic acid) (PS-b-PLA) copolymers with triazole rings as a junction between blocks. These materials were prepared via a ‘click’ strategy which involved the reaction between azide-terminated poly(styrene) (PS-N₃) and acetylene-terminated poly(D,L-lactic acid) (PLA-Ac), accomplished by copper-catalyzed azide-alkyne cycloaddition reaction. This synthetic approach has demonstrated to be effective to obtain specific copolymer structures with targeted self-assembly properties. We observed the self-assembly behavior of the PS-b-PLA thin films as induced by solvent vapor annealing (SVA), thermal annealing (TA), and hydrolysis of the as-spun substrates and monitored their morphological changes by means of different microscopic techniques. Self-assembly via SVA and TA proved to be strongly dependent on the pretreatment of the substrates. Microphase segregation of the untreated films yielded a pore size of 125 nm after a 45-min SVA. After selectively removing the PLA microdomains, the as-spun substrates exhibited the formation of pores on the surface, which can be a good alternative to form an ordered pattern of triazole functionalized porous PS at the mesoscale. Finally, as revealed by scanning electron microscopy–energy dispersive X-ray spectroscopy, the obtained triazole-functionalized PS-porous film exhibited some affinity to copper (Cu) in solution. These materials are suitable candidates to further study its metal-caption properties.

Precise fabrication of porous polymer frameworks using rigid polyisocyanides as building blocks: from structural regulation to efficient iodine capture

Porous materials have recently attracted much attention owing to their fascinating structures and broad applications. Moreover, exploring novel porous polymers affording the efficient capture of iodine is of significant interest. In contrast to the reported porous polymers fabricated with small molecular blocks, we herein report the preparation of porous polymer frameworks using rigid polyisocyanides as building blocks. First, tetrahedral four-arm star polyisocyanides with predictable molecular weight and low dispersity were synthesized; the chain-ends of the rigid polyisocyanide blocks were then crosslinked, yielding well-defined porous organic frameworks with a designed pore size and narrow distribution. Polymers of appropriate pore size were observed to efficiently capture radioactive iodine in both aqueous and vapor phases. More than 98% of iodine could be captured within 1 minute from a saturated aqueous solution (capacity of up to 3.2 g g-1), and an adsorption capacity of up to 574 wt% of iodine in vapor was measured within 4 hours. Moreover, the polymers could be recovered and recycled for iodine capture for at least six times, while maintaining high performance.

Straightforward synthesis of multifunctional porous polymer nanomaterials for CO2 capture and removal of contaminants

A straightforward synthesis of multifunctional mesoporous polymer nanomaterials suitable for the removal of contaminants and CO2 capture is reported.

Polyethyleneimine-Modified UiO-66-NH2(Zr) Metal-Organic Frameworks: Preparation and Enhanced CO2 Selective Adsorption

UiO-66-NH₂, a zirconium-based functional metal-organic framework (MOF), was postsynthetically modified via Schiff base reaction between aldehyde groups in glutaraldehyde and amino groups in UiO-66-NH₂ and CO₂-preabsorbed polyethyleneimine (PEI). The resulting PEI-modified MOFs, abbreviated as PEI^C@UiO, were characterized with ¹H NMR, Fourier transform infrared, powder X-ray diffraction, Brunauer-Emmett-Teller, scanning electron microscopy, and thermogravimetric analysis and evaluated as CO₂ adsorbents. In comparison with pristine UiO-66-NH₂, the PEI^C@UiO adsorbents have reduced specific surface area (7-150 m²/g) but maintained the same crystal structure. Particularly, the PEI^C96@UiO adsorbent exhibited significantly improved CO₂/N₂ adsorption selectivity (48 vs 25) and higher CO₂ adsorption capacity (3.2 vs 2.7 mmol/g). The adsorbent also displayed moderate desorption energy (68 kJ/mol CO₂), superior moisture endurance, and recyclability, which are very desirable for practical applications.

A polyelectrolyte-containing copolymer with a gas-switchable lower critical solution temperature-type phase transition

A polyelectrolyte-containing copolymer with a CO₂/N₂-switchable cloud point, resulting from the gas-induced alternation of hydrophilicity, was prepared.

Amino-functionalized hypercrosslinked polymers for highly selective anionic dye removal and CO2/N2 separation

Recently, great improvements have been achieved in the fabrication of adsorbents.

Macroporous monoliths with pH-induced switchable wettability for recyclable oil separation and recovery

HYPOTHESIS

The effective separation and recovery of oils from water is important for the protections of ecosystems and the environment. Polymeric porous monoliths have been demonstrated as attractive absorbents for oil/water separation. However, the recyclability was mainly realized by squeezing, combustion, or centrifugation, which may restrict in elastic materials, destroy the adsorbates or need special apparatus. Thus it is desirable to developing monoliths with controllable oil absorption and desorption.

EXPERIMENTS

A series of "smart" monoliths with pH-induced switchable wettability were fabricated by high internal phase emulsion (HIPE) polymerization and epoxide ring-opening for the incorporation of amine groups. The resultant monoliths and their wettabilities were examined using Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), nitrogen adsorption/desorption and contact angle analysis, respectively. The oil separation efficiency and recyclability were evaluated.

FINDINGS

The monoliths with macroporous structure can undergo switchable wettability under reversible pH stimulation. As an absorbent, the monoliths not only separated and recovered organic solvents and oils (including crude oil) from aqueous mixtures through a reversible and recyclable absorption and desorption process upon alternating the pH between 7.0 and 1.0, but also continuously expulsed oils from water surfaces in a continuous manner with the aid of external driving pressures. Moreover, the monoliths also allowed the effective separation of surfactant-free and surfactant-stabilized oil-in-water emulsions with high separation efficiency.