Direct Molten Polymerization Synthesis of Highly Active Samarium Manganese Perovskites with Different Morphologies for VOC Removal

Amidation-Reaction Strategy Constructs Versatile Mixed Matrix Composite Membranes towards Efficient Volatile Organic Compounds Adsorption and CO2 Separation

Mixed matrix composite membranes (MMCMs) have shown advantages in reducing VOCs and CO2 emissions. Suitable composite layer, substrate, and good compatibility between the filler and the matrix in the composite layer are critical issues in designing MMCMs. This work develops a high-performance UiO-66-NA@PDMS/MCE for VOCs adsorption and CO2 permea-selectivity, based on a simple and facile fabrication of composite layer using amidation-reaction approach on the substrate. The composite layer shows a continuous morphological appearance without interface voids. This outstanding compatibility interaction between UiO-66-NH2 and PDMS is confirmed by molecular simulations. The Si─O functional group and UiO-66-NH2 in the layer leads to improved VOCs adsorption via active sites, skeleton interaction, electrostatic interaction, and van der Waals force. The layer and ─CONH─ also facilitate CO2 transport. The MMCMs show strong four VOCs adsorption and high CO2 permeance of 276.5 GPU with a selectivity of 36.2. The existence of VOCs in UiO-66-NA@PDMS/MCE increases the polarity and fine-tunes the pore size of UiO-66-NH2, improving the affinity towards CO2 and thus promoting the permea-selectivity for CO2, which is further verified by GCMC and EMD methods. This work is expected to offer a facile composite layer manufacturing method for MMCMs with high VOC adsorption and CO2 permea-selectivity.

Weakening Mn-O Bond Strength in Mn-Based Perovskite Catalysts to Enhance Propane Catalytic Combustion

Exploring highly efficient and robust non-noble metal catalysts for VOC abatement is crucial but challenging. Mn-based perovskites are a class of redox catalysts with good thermal stability, but their activity in the catalytic combustion of light alkanes is insufficient. In this work, we modulated the Mn-O bond strength in a Mn-based perovskite via defect engineering, over which the catalytic activity of propane combustion was significantly enhanced. It demonstrates that the oxygen vacancy concentration and the Mn-O bond strength can be efficiently modulated by finely tuning the Ni content in SmNixMn1-xO3 perovskite catalysts (SNxM1-x), which in turn can enhance the redox ability and generate more active oxygen species. The SN0.10M0.90 catalyst with the lowest Mn-O bond strength exhibits the lowest apparent activation energy, over which the propane conversion rate increases by 3.6 times compared to that on the SmMnO3 perovskite catalyst (SM). In addition, a SN0.10M0.90/cordierite monolithic catalyst can also exhibit a remarkable catalytic performance and deliver excellent long-term durability (1000 h), indicating broad prospects in industrial applications. Moreover, the promotional effect of Ni substitution was further unveiled by density functional theory (DFT) calculations. This work brings a favorable guidance for the exploration of highly efficient perovskite catalysts for light alkane elimination.

Thermally Inducing Viscous Fluids to Generate Co-Based Perovskites Enriched with Active Species for the Removal of VOCs

Various Co-based perovskites are synthesized through thermally driving viscous fluids. In this process, rare earth salts, cobalt salts, and citric acid do not require homogeneous mixing but only need to be heated until they melt into a molten viscous slurry. The physicochemical properties of cobalt-based perovskites were examined using techniques such as X-ray diffraction (XRD), electron paramagnetic resonance (EPR), scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-Mapping-EDS), X-ray photoelectron spectroscopy (XPS), hydrogen temperature-programmed reduction (H2-TPR), oxygen temperature-programmed desorption (O2-TPD), and N2 adsorption-desorption. The results indicate that the surface-active species can be controlled by altering the A-site elements of cobalt-based perovskites. All catalysts synthesized through the thermal treatment of viscous mixtures exhibited a low activation temperature and a low apparent activation energy for the catalytic oxidation of toluene. Among all cobalt-based perovskites, LaCoO3 demonstrated the most outstanding catalytic activity, primarily attributed to its capacity to expose a larger number of surface-active sites and oxygen species, as well as its superior reducibility. Furthermore, the formation process of optimal LaCoO3 was monitored using thermogravimetric analysis-differential scanning calorimetry (TGA-DSC), and the byproducts of the low-temperature catalytic oxidation of toluene by the catalyst were identified using gas chromatography-mass spectrometry (GC-MS). The possible mechanism of toluene oxidation was inferred by in situ diffuse reflection infrared Fourier transform spectroscopy (DRIFTS). Moreover, LaCoO3 exhibits a predominant resistance to high-temperature hydrothermal conditions. This work provides a scalable and innovative approach to fabricating exceptionally effective catalysts for the efficient purification of VOCs.

Low-energy production of a monolithic catalyst with MnCu-synergetic enhancement for catalytic oxidation of volatile organic compounds

Producing a low-cost catalyst by a low-cost method is one of the hottest topics in the field of catalytic oxidization of volatile organic compounds (VOCs). In this work, a catalyst formula with a low-energy requirement was optimized in the powdered state, and verified in the monolithic state. An effective MnCu catalyst was synthesized at a temperature as low as 200 °C. Removals were all bigger than 88% for toluene, ethyl acetate, hexane, formaldehyde, and cyclohexanone at a low temperature of 240 °C. The MnCu catalyst was then loaded on a honeycomb cordierite, which was also effective for toluene removal at 240 °C. After characterizations, active phases were Mn₃O₄/CuMn₂O₄ in both the powdered and monolithic catalysts. The enhanced activity was attributed to balanced distributions of low-valence Mn and Cu, as well as abundant surface oxygen vacancies. The obtained catalyst is produced by low energy and effective at low temperature, which suggests a perspective application.

Catalytic Degradation of Toluene over MnO2/LaMnO3: Effect of Phase Type of MnO2 on Activity

Series of α, β, γ, δ type MnO2 supported on LaMnO3 perovskite was developed by a one-pot synthesis route. Compared with α-MnO2, β-MnO2, γ-MnO2, δ-MnO2 and LaMnO3 oxides, all MnO2/LaMnO3 showed promotional catalytic performance for toluene degradation. Among them, α-MnO2/LaMnO3 holds the best active and mineralization efficiency. By the analysis of N2 adsorption-desorption, XPS and H2-TPR, it can be inferred that the improved activity should be ascribed to the higher proportion of lattice oxygen, better low-temperature reducibility and larger specific surface area. Besides, the byproducts from the low-temperature reaction of toluene oxidation were detected by a TD/GC-MS, confirming the presence of the intermediates. Combined with the in-situ DRIFTS, the catalytic degradation path of toluene oxidation has also been discussed in depth.

A review of the advances in catalyst modification using nonthermal plasma: Process, Mechanism and Applications

With the continuous development of catalytic processes in chemistry, biology, organic synthesis, energy generation and many other fields, the design of catalysts with novel properties has become a new paradigm in both science and industry. Nonthermal plasma has aroused extensive interest in the synthesis and modification of catalysts. An increasing number of researchers are using plasma for the modification of target catalysts, such as modifying the dispersion of active sites, regulating electronic properties, enhancing metal-support interactions, and changing the morphology. Plasma provides an alternative choice for catalysts in the modification process of oxidation, reduction, etching, coating, and doping and is especially helpful for unfavourable thermodynamic processes or heat-sensitive reactions. This review focuses on the following points: (i) the fundamentals behind the nonthermal plasma modification of catalysts; (ii) the latest research progress on the application of plasma modified catalysts; and (iii) main challenges in the field and a vision for future development.

Combined experimental and theoretical study of o-xylene elimination on Fe-Mn oxides catalysts

The development of low-cost and easily accessible catalysts to realize the practical applications of catalytic combustion of volatile organic compounds remains a challenge. In this work, a series of Fe-Mn oxides catalysts were prepared via a facile redox-precipitation route for the elimination of o-xylene. Among the synthesized catalysts, Fe3Mn1-RP exhibited excellent activity for o-xylene elimination with a T₅₀ and T₉₀ of 223 °C and 236 °C, respectively (o-xylene concentration = 500 ppm, WHSV = 36,000 mL g^-1 h^-1). Characterization results demonstrated that superior catalytic activity could be achieved from large specific surface area, good reducibility and high proportion of Mn⁴⁺. Besides, high Fe contents proved beneficial in generating additional oxygen vacancies, thereby improving the performance of the catalyst. The stable crystal structures and surface electron density distributions of the catalysts, and adsorption sites of o-xylene on the catalyst surface, were also determined through density functional theory (DFT) calculations to provide an in-depth mechanism on how the o-xylene oxidation occurred. Moreover, analysis of the energy barrier during the oxidation process proved that the ring-opening reaction on the surface of Fe3Mn1-RP with an activation energy as low as 2.46 eV would more likely occur via oxygen vacancies.

In-situ regulation of acid sites on Mn-based perovskite@mullite composite for promoting catalytic oxidation of chlorobenzene

A series of Sm-Mn perovskite@mullite composites with different amounts of acid sites were successfully synthesized by regulating the level of in situ etched-surface modification. X-ray diffraction (XRD) test showed that the crystal structure of catalyst gradually changed from perovskite to perovskite@mullite composites and mullite. The characterization of temperature programmed desorption with ammonia (NH₃-TPD) confirmed the acid sites on the surface of catalyst can be deployed by the in-situ modification. The temperature-programmed reduction with hydrogen (H₂-TPR), and N₂ adsorption-desorption showed that the surface modification also increased the reducibility, surface area, and mesoporosity of catalyst. The catalytic activities were compared by a long-term catalytic oxidation of chlorobenzene evaluation for 20 h of uninterrupted reaction at a relatively low temperature of 300 °C, and the Sm-Mn perovskite@mullite composite (SMPM-1.2) possessed the best catalytic stability. The X-ray photoelectron spectroscopy (XPS) measurement determined that the high ratios of lattice oxygen and tetravalent manganese did not improve the stability of catalyst in the catalytic oxidation of chlorobenzene, but the activities trends of samples were consistent with the change of surface (Mn⁴⁺+Mn³⁺)/Mn²⁺ ratios. Meanwhile, the catalytic experiments for benzene, toluene, o-xylene and acetone showed that the as-prepared catalyst was also suitable for the efficient removal of the different types of VOCs. This work supplied a method for the further development of high activity catalysts for the removal of VOCs.

Direct complexation of citric acid to synthesize high-efficiency bismuth vanadate through molten polymerization route for the degradation of tetracycline hydrochloride under visible light irradiation

Tetracycline hydrochloride can be efficiently degraded over BiVO4 prepared through direct citric acid complexation.

The Influence of the Chemical Potential on Defects and Function of Perovskites in Catalysis

A Sm-deficient Sm_0.96MnO₃ perovskite was prepared on a gram scale to investigate the influence of the chemical potential of the gas phase on the defect concentration, the oxidation states of the metals and the nature of the oxygen species at the surface. The oxide was treated at 450°C in nitrogen, synthetic air, oxygen, water vapor or CO and investigated for its properties as a catalyst in the oxidative dehydrogenation of propane both before and after treatment. After treatment in water vapor, but especially after treatment with CO, increased selectivity to propene was observed, but only when water vapor was added to the reaction gas. As shown by XRD, SEM, EDX and XRF, the bulk structure of the oxide remained stable under all conditions. In contrast, the surface underwent strong changes. This was shown by AP-XPS and AP-NEXAFS measurements in the presence of the different gas atmospheres at elevated temperatures. The treatment with CO caused a partial reduction of the metals at the surface, leading to changes in the charge of the cations, which was compensated by an increased concentration of oxygen defects. Based on the present experiments, the influence of defects and concentration of electrophilic oxygen species at the catalyst surface on the selectivity in propane oxidation is discussed.

Improved catalytic oxidation of propylene glycol methyl ether over Sm-Mn and Sm-Co perovskite-based catalysts prepared by the recycling of spent ternary lithium-ion battery

The spent ternary lithium-ion batteries were utilized as the precursors to prepare Sm-Mn and Sm-Co perovskite oxides (SmMnO₃-spent ternary lithium-ion battery [STLIB] and SmCoO₃-STLIB) for the first time. Their catalytic activities were evaluated by catalytic oxidation of propylene glycol methyl ether. Compared with that of the catalysts synthesized by analytical reagents, the catalytic activities of SmMnO₃-STLIB and SmCoO₃-STLIB had been significantly enhanced. The analysis of X-ray photoelectron spectroscopy (XPS) showed that the molar ratios of Mn⁴⁺/Mn³⁺ and O_ads/O_latt of SmMnO₃-STLIB were higher than that of pure SmMnO₃ and the Co³⁺/Co²⁺ ratios of SmCoO₃-STLIB was much larger than that of pure SmCoO₃. The hydrogen temperature-programmed reduction (H₂-TPR) and N₂ adsorption-desorption tests determined that the reducibilities and specific surface areas of SmMnO₃-STLIB and SmCoO₃-STLIB were also superior to pure catalysts. Ultimately, the by-products of the catalytic oxidation of propylene glycol methyl ether over SmMnO₃-STLIB were also detected by gas chromatography-mass spectrometry (GC-MS). This work will provide a demonstration for the resource utilization of spent lithium ions batteries and the analysis of the increased activity obtained by using spent lithium ions batteries as the precursors to prepare catalysts.

Recent Progress of Thermocatalytic and Photo/Thermocatalytic Oxidation for VOCs Purification over Manganese-based Oxide Catalysts

Volatile organic compounds (VOCs) are one of the main sources of air pollution, which are of wide concern because of their toxicity and serious threat to the environment and human health. Catalytic oxidation has been proven to be a promising and effective technology for VOCs abatement in the presence of heat or light. As environmentally friendly and low-cost materials, manganese-based oxides are the most competitive and promising candidates for the catalytic degradation of VOCs in thermocatalysis or photo/thermocatalysis. This article summarizes the research and development on various manganese-based oxide catalysts, with emphasis on their thermocatalytic and photo/thermocatalytic purification of VOCs in recent years in detail. Single manganese oxides, manganese-based oxide composites, as well as improving strategies such as morphology regulation, heterojunction engineering, and surface decoration by metal doping or universal acid treatment are reviewed. Besides, manganese-based monoliths for practical VOCs abatementare also discussed. Meanwhile, relevant catalytic mechanisms are also summarized. Finally, the existing problems and prospect of manganese-based oxide catalysts for catalyzing combustion of VOCs are proposed.

Pt/MnO2 Nanoflowers Anchored to Boron Nitride Aerogels for Highly Efficient Enrichment and Catalytic Oxidation of Formaldehyde at Room Temperature

The catalytic room temperature oxidation of formaldehyde (HCHO) is widely considered as a viable method for the abatement of indoor toxic HCHO pollution. Herein, Pt/MnO₂ nanoflowers anchored to boron nitride aerogels (Pt/MnO₂ -BN) were fabricated for the catalytic room temperature oxidation of HCHO. The three-dimensional Pt/MnO₂ -BN aerogels demonstrated superior catalytic activity as a result of the improved diffusion of the reactant molecules within the porous structure. Furthermore, the porous aerogels displayed excellent HCHO adsorption capacities, which promote a rapid HCHO gas-phase concentration reduction and a subsequent complete oxidation of the adsorbed HCHO. The combined adsorption and oxidation properties of the Pt/MnO₂ -BN aerogels enhance the oxidative removal of HCHO. The optimized Pt/MnO₂ -BN demonstrated excellent catalytic activity toward HCHO (200 ppm) at room temperature, achieving a 96 % formaldehyde conversion after 50 min.

Recovery of cathode materials from spent lithium-ion batteries and their application in preparing multi-metal oxides for the removal of oxygenated VOCs: Effect of synthetic methods

Due to the sustainable use of wastes, cathode materials of spent lithium-ion batteries are recovered and used as transition metal precursors to prepare metal oxides catalysts for the oxidation of VOCs. In this work, a series of manganese-based and cobalt-based metal oxides are synthesized via different preparation methods. Catalytic activities of the catalysts prepared are investigated through complete oxidation of oxygenated VOCs and the physicochemical properties of optimum samples are characterized. Evaluation results indicate that MnOx (SY) (HT) sample prepared via hydrothermal method and CoOx (GS) (CP) synthesized via co-precipitation method had better performance, because they have higher specific surface area, higher concentration of active oxygen species and high-valence metal ion, as well as better low-temperature reducibility compared to the other multi-metal oxides used in the study. In addition, TD/GC-MS results imply that further oxidation of by-products requires high reaction temperature during VOCs oxidation.

Enhanced catalytic oxidation of VOCs over porous Mn-based mullite synthesized by in-situ dismutation

Porous Mn-based mullite SmMn₂O₅ was synthesized by the in-situ dismutation of solid state Mn³⁺ in bulk SmMnO₃ perovskite to catalytic oxidation of benzene and chrolobenznen. The physicochemical property of catalyst was acquired by XRD, SEM, N₂ adsorption-desorption, XPS, O₂-TPD and H₂-TPR. Compared with that of bulk SmMnO₃ and bulk SmMn₂O₅, the porous SmMn₂O₅ mullite (SmMn₂O₅-ID) displayed higher molar ratios of Mn⁴⁺/Mn³⁺ and O_latt/O_ads, and better active oxygen desorption capacity, reducibility and larger specific surface, which promoted the preferable low-temperature catalytic oxidation of VOC. The increase in the content of Mn⁴⁺ on the surface of the Sm-Mn mullite reduced the surface defects and increased the proportion of its surface lattice oxygen, thereby promoting the attack of VOC molecules by more lattice oxygen. Combined with the analysis of reactant intermediate for benzene oxidation by in situ diffuse reflectance infrared Fourier transform spectroscopy, the catalytic mechanism of the catalyst was also explored. Moreover, SmMn₂O₅-ID also showed the excellent stability and the superior removal of mixed VOCs with different concentration ratios. This finding provides an efficient and practical method for exploiting highly active Mn-based mullite with a high efficiency and stability for the purification of air pollution.

Promotional removal of oxygenated VOC over manganese-based multi oxides from spent lithium-ions manganate batteries: Modification with Fe, Bi and Ce dopants

In this work, cathode materials of spent lithium-ions manganate batteries are recovered as the precursor of manganese-based oxides catalysts and furthermore, different amount of Fe, Bi, Ce are introduced to modify their properties. A series of MnOx(MS)-X Fe, MnOx(MS)-X Bi and MnOx(MS)-X Ce samples with crystal phase of Mn₅O₈ are synthesized using combustion method and then the catalytic behavior and physicochemical properties of prepared catalysts are investigated. Compared to binary MnOx-5% Fe, MnOx-15% Bi and MnOx-10% Ce samples, multi MnOx(MS)-5% Fe, MnOx(MS)-15 Bi and MnOx(MS)-10% Ce catalysts display enhanced catalytic performance significantly in the removal of oxygenated VOC, which could be attributed to larger specific surface area, higher concentration of surface active oxygen species and Mn⁴⁺ ions and better reducibility at low temperature. In-situ DRIFTS results imply that main oxygen-containing functional groups such as carbonyl (-C=O), carboxyl (-COO), hydroxyl (-OH) can be observed during VOC oxidation and by comparison, it can be found that gas-phase O₂ plays a crucial role in facilitating the further oxidation of by-products into CO₂. In addition, TD/GC-MS results point out that the main by-products are formaldehyde; 2-propanol, 1-methoxy-; ethanol, 2-methoxy-, acetate; 2-ethoxyethyl acetate; acetic acid during VOC oxidation.

Porous Mn-based oxides for complete ethanol and toluene catalytic oxidation: the relationship between structure and performance

SmMn₂O₅ exhibited a higher catalytic activity for catalytic oxidation of ethanol and toluene than SmMnO₃, Mn₃O₄ and Mn₂O₃. Mn³⁺–Mn³⁺ dimers facilitate C–C bond cleavage.

Manganese-based multi-oxide derived from spent ternary lithium-ions batteries as high-efficient catalyst for VOCs oxidation

Valuable metals such as manganese, cobalt, nickel and copper are recycled from spent ternary lithium-ions batteries (LiBs) and are considered as the active metal precursor to prepare based-manganese multi oxide for VOCs oxidation. The results of characterization analysis indicate that the catalyst from spent LiBs shows larger specific surface area of 26.80 m²/g as well as abundant mesoporous structures on the surface, higher molar ratio of Mn⁴⁺/Mn³⁺ (0.70) and O_latt/O_ads (1.68), better low-temperature reductivity and stronger intensity of weak acid sites in comparison with those of pure manganese oxides. The evaluation experiments show that the catalyst from waste exhibits more excellent catalytic performance of toluene combustion in comparison with pure manganese oxides. Furthermore, the presence of considerable amount of lithium and aluminum ions can severely weaken the catalytic activity while the co-existence of nickel, cobalt and copper ions contribute a lot to facilitate the catalytic behavior. In-situ DRIFT study implies that the introduction of lithium, aluminum, nickel, copper and cobalt into pure manganese oxides can facilitate toluene conversion to various extents, following the consecutive steps via benzyl species, benzoyl oxide species, benzaldehyde species, benzoate species and the primary intermediates are benzoate species.

Alternative pathways to α,β-unsaturated ketones via direct oxidative coupling transformation using Sr-doped LaCoO3 perovskite catalyst

A strontium-doped lanthanum cobaltite perovskite material was prepared, and used as a recyclable and effective heterogeneous catalyst for the direct oxidative coupling of alkenes with aromatic aldehydes to produce α,β-unsaturated ketones. The reaction afforded high yields in the presence of di-tert-butylperoxide as oxidant. Single oxides or salts of strontium, lanthanum and cobalt, and the undoped perovskite offered a lower catalytic activity than the strontium-doped perovskite. Benzaldehyde could be replaced by benzyl alcohol, dibenzyl ether, 2-oxo-2-phenylacetaldehyde, 2-bromoacetophenone or (dimethoxymethyl) benzene in the oxidative coupling reaction with alkenes. To our best knowledge, reactions between these starting materials with alkenes are new and unknown in the literature.

Catalytic Oxidation of VOCs over SmMnO3 Perovskites: Catalyst Synthesis, Change Mechanism of Active Species, and Degradation Path of Toluene

Highly active samarium manganese perovskite oxides were successfully prepared by employing self-molten-polymerization, coprecipitation, sol-gel, and impregnation methods. The physicochemical properties of perovskite oxides were investigated by XRD, N₂ adsorption-desorption, XPS, and H₂-TPR. Their catalytic performances were compared via the catalytic oxidation of toluene. The perovskite prepared by self-molten-polymerization possessed the highest catalytic capacity, which can be ascribed to its higher oxygen adspecies concentration (O_latt/O_ads = 0.53), higher surface Mn⁴⁺/Mn³⁺ ratio (Mn⁴⁺/Mn³⁺ = 0.95), and best low-temperature reducibility (H₂ consumption = 0.27; below 350 °C). The most active catalyst also exhibited good cycling and long-term stability for toluene oxidation. After a multistep cycle reaction and a long-term reaction of 42 h, the toluene conversion maintained above 99.9% at 270 °C. Mechanistic study hinted that lattice oxygen was involved in toluene oxidation. The oxidation reaction was dependent on the synergism of lattice oxygen, adsorbed oxygen, and oxygen vacancies. The degradation pathway of toluene, researched by diffuse reflectance infrared Fourier transform spectroscopy and online mass spectrometry technologies, demonstrated that a series of organic byproducts existed at a relatively low temperature. This work provides an efficient and practical method for selecting highly active catalysts and for exploring the catalytic mechanism for the removal of atmospheric environmental pollution.

In situ fabrication of highly active γ-MnO2/SmMnO3 catalyst for deep catalytic oxidation of gaseous benzene, ethylbenzene, toluene, and o-xylene

γ-MnO₂, SmMnO₃, and γ-MnO₂/SmMnO₃ catalysts were prepared by facile methods, wherein the SmMnO₃ (SMO) perovskite was synthesized through one-step calcination and the γ-MnO₂/SmMnO₃ was formed by an in situ growth of γ-MnO₂ on the surface of SMO. These materials ware characterized by XRD, SEM-mapping, N₂-adsorption, XPS and H₂-TPR to investigate their textural properties. Compared with that of SMO and γ-MnO₂, the γ-MnO₂/SMO shows better performance for catalytic oxidation of aromatic VOCs in wet air (10 vol.%), which may be attributed to its higher surface molar ratio of lattice oxygen to adsorbed oxygen (O_latt/O_ads) and better low-temperature reducibility. Besides, for γ-MnO₂/SMO catalyst, a successive oxidation route and the inner principle of BETX (benzene, ethylbenzene, toluene, and o-xylene) oxidation were also revealed via various tests and a comprehension of dynamics investigation. Meanwhile, the experiments under simulated realistic exhaust conditions displayed that the γ-MnO₂/SmMnO₃ is also a good catalyst with high stability for aromatic VOCs oxidation, and fulfilled endurability to high humidity (20 vol.%).

Self-molten-polymerization synthesis of highly defected Mn/Sm binary oxides with mesoporous structures for efficient removal of toluene and chlorobenzene

Oxygen vacancies were induced via transition metal doping in MnO_x for the low-temperature and efficient removal of toluene and chlorobenzene.