1
|
Wang W, Yang Y, Liu C, Chen B, Chen X, Wang H, Tong R, Zhou S. Study of Coating Growth Direction of 6061 Aluminum Alloy in Soft Spark Discharge of Plasma Electrolytic Oxidation. MATERIALS (BASEL, SWITZERLAND) 2024; 17:2947. [PMID: 38930316 PMCID: PMC11205352 DOI: 10.3390/ma17122947] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 04/24/2024] [Revised: 06/12/2024] [Accepted: 06/13/2024] [Indexed: 06/28/2024]
Abstract
Conventional plasma electrolytic oxidation treatments produce oxide coatings with micron-scale discharge pores, resulting in insulation and wear and corrosion resistance far below that expected of highly dense Al2O3 coatings. The introduction of cathodic polarization during the plasma electrolytic oxidation process, especially when the applied cathode-to-anode current ratio (Rpn) is greater than 1, triggers a unique plasma discharge phenomenon known as "soft sparking". The soft spark discharge mode significantly improves the densification of the anode ceramic layer and facilitates the formation of the high-temperature α-Al2O3 phase within the coating. Although the soft spark discharge phenomenon has been known for a long time, the growth behavior of the coating under its discharge mode still needs to be studied and improved. In this paper, the growth behavior of the coating before and after soft spark discharge is investigated with the help of the micro-morphology, phase composition and element distribution of a homemade fixture. The results show that the ceramic layer grows mainly along the oxide-electrolyte direction before the soft spark discharge transformation; after the soft spark discharge, the ceramic layer grows along the oxide-substrate direction. It was also unexpectedly found that, under soft spark discharge, the silicon element only exists on the outside of the coating, which is caused by the large size and slow migration of SiO32-, which can only enter the ceramic layer and participate in the reaction through the discharge channel generated by the strong discharge. In addition, it was also found that the relative phase content of α-Al2O3 in the coating increased from 0.487 to 0.634 after 10 min of rotary spark discharge, which is an increase of 30.2% compared with that before the soft spark discharge transition. On the other hand, the relative phase content of α-Al2O3 in the coating decreased from 0.487 to 0.313 after 20 min of transfer spark discharge, which was a 55.6% decrease compared to that before the soft spark discharge transformation.
Collapse
Affiliation(s)
| | | | - Cancan Liu
- College of Materials Science and Engineering, Nanjing Tech University, Nanjing 211800, China; (W.W.); (Y.Y.); (B.C.); (X.C.); (H.W.); (R.T.); (S.Z.)
| | | | | | | | | | | |
Collapse
|
2
|
Li H, Kong S, Liu Z, Wang Z, Geng Y. Hardness Distribution and Growth Behavior of Micro-Arc Oxide Ceramic Film with Positive and Negative Pulse Coordination. NANOMATERIALS (BASEL, SWITZERLAND) 2024; 14:842. [PMID: 38786798 PMCID: PMC11124304 DOI: 10.3390/nano14100842] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 03/17/2024] [Revised: 04/28/2024] [Accepted: 05/01/2024] [Indexed: 05/25/2024]
Abstract
Micro-arc oxidation (MAO) is a promising technology for enhancing the wear resistance of engine cylinders by growing a high hardness alumina ceramic film on the surface of light aluminum engine cylinders. However, the positive and negative pulse coordination, voltage characteristic signal, hardness distribution characteristics of the ceramic film, and their internal mechanism during the growth process are still unclear. This paper investigates the synergistic effect mechanism of cathodic and anodic current on the growth behaviour of alumina, dynamic voltage signal, and hardness distribution of micro-arc oxidation film. Ceramic film samples were fabricated under various conditions, including current densities of 10, 12, 14, and 16 A/dm2, and current density ratios of cathode and anode of 1.1, 1.2, and 1.3, respectively. Based on the observed characteristics of the process voltage curve and the spark signal changes, the growth of the ceramic film can be divided into five stages. The influence of positive and negative current density parameters on the segmented growth process of the ceramic film is mainly reflected in the transition time, voltage variation rate, and the voltage value of different growth stages. Enhancing the cathode pulse effect or increasing the current density level can effectively shorten the transition time and accelerate the voltage drop rate. The microhardness of the ceramic film cross-section presents a discontinuous soft-hard-soft regional distribution. Multiple thermal cycles lead to a gradient differentiation of the Al2O3 crystal phase transition ratio along the thickness direction of the layer. The layer grown on the outer surface of the initial substrate exhibits the highest hardness, with a small gradient change in hardness, forming a high hardness zone approximately 20-30 μm wide. This high hardness zone extends to both sides, with hardness decreasing rapidly.
Collapse
Affiliation(s)
- Haomin Li
- State Key Laboratory of Electrical Insulation and Power Equipment, Xi’an Jiaotong University, Xi’an 710049, China
| | | | | | | | | |
Collapse
|
3
|
Gong W, Ma R, Du A, Zhao X, Fan Y. The Effects of the Pre-Anodized Film Thickness on Growth Mechanism of Plasma Electrolytic Oxidation Coatings on the 1060 Al Substrate. MATERIALS (BASEL, SWITZERLAND) 2023; 16:5922. [PMID: 37687615 PMCID: PMC10488349 DOI: 10.3390/ma16175922] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 08/05/2023] [Revised: 08/21/2023] [Accepted: 08/22/2023] [Indexed: 09/10/2023]
Abstract
To increase the density of the micro-arc oxide coating, AA 1060 samples were pretreated with an anodic oxide film in an oxalic acid solution. Plasma electrolytic oxidation (PEO) was performed to investigate the effect of the thickness of the pre-anodic oxide film on the soft-sparking mechanism. The experimental results revealed that the PEO coating phases with different thicknesses of the pre-anodized films contained both Al and gamma-alumina (γ-Al2O3). The pre-anodized film changes the final morphology of the coating, accelerating the soft sparking transition and retaining the soft sparking. At a pre-anodized film thickness of ≤7.7 μm, the anodized films thickened before being broken through. When the pre-anodized film thickness was ≥13.1 μm, partial dissolution of the anodized films occurred before they were struck through. Two growth mechanisms for PEO coatings with different pre-anodized film thicknesses were proposed.
Collapse
Affiliation(s)
- Wanting Gong
- School of Materials Science and Engineering, Hebei University of Technology, Tianjin 300130, China; (W.G.); (A.D.); (X.Z.); (Y.F.)
| | - Ruina Ma
- School of Materials Science and Engineering, Hebei University of Technology, Tianjin 300130, China; (W.G.); (A.D.); (X.Z.); (Y.F.)
- Key Laboratory for New Type of Functional Materials in Hebei Province, Tianjin 300130, China
| | - An Du
- School of Materials Science and Engineering, Hebei University of Technology, Tianjin 300130, China; (W.G.); (A.D.); (X.Z.); (Y.F.)
- Key Laboratory for New Type of Functional Materials in Hebei Province, Tianjin 300130, China
| | - Xue Zhao
- School of Materials Science and Engineering, Hebei University of Technology, Tianjin 300130, China; (W.G.); (A.D.); (X.Z.); (Y.F.)
- Key Laboratory for New Type of Functional Materials in Hebei Province, Tianjin 300130, China
| | - Yongzhe Fan
- School of Materials Science and Engineering, Hebei University of Technology, Tianjin 300130, China; (W.G.); (A.D.); (X.Z.); (Y.F.)
- Key Laboratory for New Type of Functional Materials in Hebei Province, Tianjin 300130, China
| |
Collapse
|
4
|
Zhu M, Song Y, Dong K, Shan D, Han EH. Correlation between the transient variation in positive/negative pulse voltages and the growth of PEO coating on 7075 aluminum alloy. Electrochim Acta 2022. [DOI: 10.1016/j.electacta.2022.140056] [Citation(s) in RCA: 3] [Impact Index Per Article: 1.5] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/15/2022]
|
5
|
Abstract
Over the past several decades, an increasing amount of attention has been given to catalytic combustion as an environmentally friendly process. However, major impediments to large-scale application still arise on the materials side. Here, we review catalytic combustion on thin film catalysts in view of highlighting some interesting features. Catalytic films open the way for new designs of structured catalysts and the construction of catalysts for catalytic combustion. A special place is occupied by materials in the form of very thin films that reveal catalytic activity for various chemical reactions. In this review, we demonstrate the high catalytic activity of thin film catalysts in these oxidation reactions.
Collapse
|
6
|
Casanova L, La Padula M, Pedeferri M, Diamanti MV, Ormellese M. An insight into the evolution of corrosion resistant coatings on titanium during bipolar plasma electrolytic oxidation in sulfuric acid. Electrochim Acta 2021. [DOI: 10.1016/j.electacta.2021.138190] [Citation(s) in RCA: 6] [Impact Index Per Article: 2.0] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 02/05/2023]
|
7
|
Optimization of Surface Properties of Plasma Electrolytic Oxidation Coating by Organic Additives: A Review. COATINGS 2021. [DOI: 10.3390/coatings11040374] [Citation(s) in RCA: 8] [Impact Index Per Article: 2.7] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 01/19/2023]
Abstract
Plasma electrolytic oxidation (PEO) is an effective surface modification method for producing ceramic oxide layers on metals and their alloys. Although inorganic electrolytes are widely used in PEO, the organic additives have received considerable interest in the last decade due to their roles in improving the final voltage and controlling spark discharging, which lead to significant improvements in the performance of the obtained coatings. Therefore, this review summarized recent progress in the impacts of organic additives on the electrical response and the plasma discharges behavior during the PEO process. The detailed influence of organic additives, namely alcohols, organic acids, organic amines, organic acid salts, carbohydrate compounds, and surfactants on the corrosion behavior of PEO coatings is outlined. Finally, the future aspects and challenges that limit the industrial applications of PEO coating made in organic electrolytes are also highlighted.
Collapse
|
8
|
Rogov AB, Matthews A, Yerokhin A. Relaxation Kinetics of Plasma Electrolytic Oxidation Coated Al Electrode: Insight into the Role of Negative Current. THE JOURNAL OF PHYSICAL CHEMISTRY. C, NANOMATERIALS AND INTERFACES 2020; 124:23784-23797. [PMID: 33193942 PMCID: PMC7659332 DOI: 10.1021/acs.jpcc.0c07714] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.3] [Reference Citation Analysis] [Abstract] [Track Full Text] [Figures] [Subscribe] [Scholar Register] [Received: 08/24/2020] [Revised: 09/16/2020] [Indexed: 06/11/2023]
Abstract
Plasma electrolytic oxidation (PEO) is an advanced coating process based on high-voltage anodizing. Notwithstanding the anodic nature of the PEO process, it is known that negative polarization leads to synergetic effects in oxide formation efficiency and characteristics of resulting coatings. In this work, we used dynamic anodic voltammograms derived from polarization signal, combining working and diagnostic segments to evaluate in real time the effects of negative polarization on the formation of PEO on the coating on Al in the bipolar regime with a frequency of 50 Hz and a negative-to-positive charge ratio of 1.3. It was found that the hysteresis between ascending and descending branches of the voltammogram can be both caused by prior cathodic polarization and spontaneously generated under unpolarized conditions. This indicated the existence of a quasi-equilibrium in the chemical state of the coating material, which could be perturbed by the external bipolar polarization. The characteristic relaxation time for this system was found to be 40-370 ms. The quasi-equilibrium was attributed to a reversible hydration/dehydration reaction taking place in the active zone of anodic alumina layer (degree of hydration: 10-40%). Coating response analysis via kinetic hydration model allowed both explanations to be provided to a number of previous experimental observations and practical recommendations to be made for the design of efficient electrical regimes for intelligent PEO processes. The latter includes recommendations on avoiding long pauses during negative to positive switching.
Collapse
Affiliation(s)
- Aleksey B. Rogov
- Department
of Materials, University of Manchester, Manchester M139PL, United Kingdom
- Scientific
and Technical Centre “Pokrytie-A”, Novosibirsk 630015, Russia
| | - Allan Matthews
- Department
of Materials, University of Manchester, Manchester M139PL, United Kingdom
| | - Aleksey Yerokhin
- Department
of Materials, University of Manchester, Manchester M139PL, United Kingdom
| |
Collapse
|
9
|
|
10
|
Introduction to Plasma Electrolytic Oxidation—An Overview of the Process and Applications. COATINGS 2020. [DOI: 10.3390/coatings10070628] [Citation(s) in RCA: 36] [Impact Index Per Article: 9.0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 02/01/2023]
Abstract
Plasma electrolytic oxidation (PEO), also called micro-arc oxidation (MAO), is an innovative method in producing oxide-ceramic coatings on metals, such as aluminum, titanium, magnesium, zirconium, etc. The process is characterized by discharges, which develop in a strong electric field, in a system consisting of the substrate, the oxide layer, a gas envelope, and the electrolyte. The electric breakdown in this system establishes a plasma state, in which, under anodic polarization, the substrate material is locally converted to a compound consisting of the substrate material itself (including alloying elements) and oxygen in addition to the electrolyte components. The review presents the process kinetics according to the existing models of the discharge phenomena, as well as the influence of the process parameters on the process, and thus, on the resulting coating properties, e.g., morphology and composition.
Collapse
|
11
|
Effect of Pulse Current Mode on Microstructure, Composition and Corrosion Performance of the Coatings Produced by Plasma Electrolytic Oxidation on AZ31 Mg Alloy. COATINGS 2019. [DOI: 10.3390/coatings9100688] [Citation(s) in RCA: 23] [Impact Index Per Article: 4.6] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 01/20/2023]
Abstract
Plasma electrolytic oxidation (PEO) coatings were grown on AZ31 Mg alloy in a silicate-based electrolyte containing KF using unipolar and bipolar (usual and soft-sparking) waveforms. The coatings were dual-layered consisting of MgO, MgF2 and Mg2SiO4 phases. Surface morphology of the coatings was a net-like (scaffold) containing a micro-pores network, micro-cracks and granules of oxide compounds. Deep pores were observed in the coating produced by unipolar and usual bipolar waveforms. The soft-sparking eliminated the deep pores and produced the lowest porosity in the coatings. It was found that the corrosion performance of the coatings evaluated using EIS in 3.5 wt. % NaCl solution is mostly determined by the inner layer resistance, because of its higher compactness. After 4 days of immersion, the inner layer resistances were almost the same for all coatings. However, the coatings produced by unipolar and usual bipolar waveforms showed sharp decays in inner layer resistances after 1 week and even the barrier effect of outer layer was lost for the unipolar-produced coating after 3 weeks. The low-frequency inductive loops appeared after a 3-week immersion for all coatings indicated that the substrate was under local corrosion attack. However, both coatings produced by soft-sparking waveforms provided the highest corrosion performance.
Collapse
|
12
|
Rogov AB, Matthews A, Yerokhin A. Role of cathodic current in plasma electrolytic oxidation of Al: A quantitative approach to in-situ evaluation of cathodically induced effects. Electrochim Acta 2019. [DOI: 10.1016/j.electacta.2019.05.161] [Citation(s) in RCA: 28] [Impact Index Per Article: 5.6] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/04/2023]
|
13
|
A Novel Self-Adaptive Control Method for Plasma Electrolytic Oxidation Processing of Aluminum Alloys. MATERIALS 2019; 12:ma12172744. [PMID: 31461869 PMCID: PMC6747983 DOI: 10.3390/ma12172744] [Citation(s) in RCA: 8] [Impact Index Per Article: 1.6] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 08/11/2019] [Revised: 08/23/2019] [Accepted: 08/23/2019] [Indexed: 01/29/2023]
Abstract
Plasma electrolytic oxidation processing is a novel promising surface modification approach for various materials. However, its large-scale application is still restricted, mainly due to the problem of high energy consumption of the plasma electrolytic oxidation processing. In order to solve this problem, a novel intelligent self-adaptive control technology based on real-time active diagnostics and on the precision adjustment of the process parameters was developed. Both the electrical characteristics of the plasma electrolytic oxidation process and the microstructure of the coating were investigated. During the plasma electrolytic oxidation process, the discharges are maintained in the soft-sparking regime and the coating exhibits a good uniformity and compactness. A total specific energy consumption of 1.8 kW h m-2 μm-1 was achieved by using such self-adaptive plasma electrolytic oxidation processing on pre-anodized 6061 aluminum alloy samples.
Collapse
|
14
|
Aliasghari S, Skeldon P, Zhou X, Valizadeh R, Junginger T, Stenning GBG, Burt G. Superconducting properties of PEO coatings containing MgB2 on niobium. J APPL ELECTROCHEM 2019. [DOI: 10.1007/s10800-019-01339-6] [Citation(s) in RCA: 3] [Impact Index Per Article: 0.6] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/29/2022]
|
15
|
Park CS, Jung EY, Jang HJ, Bae GT, Shin BJ, Tae HS. Synthesis and Properties of Plasma-Polymerized Methyl Methacrylate via the Atmospheric Pressure Plasma Polymerization Technique. Polymers (Basel) 2019; 11:E396. [PMID: 30960380 PMCID: PMC6473653 DOI: 10.3390/polym11030396] [Citation(s) in RCA: 12] [Impact Index Per Article: 2.4] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 12/17/2018] [Revised: 02/11/2019] [Accepted: 02/22/2019] [Indexed: 01/21/2023] Open
Abstract
Pinhole free layers are needed in order to prevent oxygen and water from damaging flexible electrical and bio-devices. Although polymerized methyl methacrylate (polymethyl methacrylate, PMMA) for the pinhole free layer has been studied extensively in the past, little work has been done on synthesizing films of this material using atmospheric pressure plasma-assisted electro-polymerization. Herein, we report the synthesis and properties of plasma-PMMA (pPMMA) synthesized using the atmospheric pressure plasma-assisted electro-polymerization technique at room temperature. According to the Fourier transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), and time of flight-secondary ion mass spectrometry (ToF-SIMS) results, the characteristic peaks from the pPMMA polymer chain were shown to have been detected. The results indicate that the percentage of hydrophobic groups (C⁻C and C⁻H) is greater than that of hydrophilic groups (C⁻O and O⁻C=O). The field emission-scanning electron microscope (FE-SEM) and thickness measurement results show that the surface morphology is quite homogenous and amorphous in nature, and the newly proposed pPMMA film at a thickness of 1.5 µm has high transmittance (about 93%) characteristics. In addition, the results of water contact angle tests show that pPMMA thin films can improve the hydrophobicity.
Collapse
Affiliation(s)
- Choon-Sang Park
- School of Electronics Engineering, College of IT Engineering, Kyungpook National University, Daegu 41566, Korea.
| | - Eun Young Jung
- School of Electronics Engineering, College of IT Engineering, Kyungpook National University, Daegu 41566, Korea.
| | - Hyo Jun Jang
- School of Electronics Engineering, College of IT Engineering, Kyungpook National University, Daegu 41566, Korea.
| | - Gyu Tae Bae
- School of Electronics Engineering, College of IT Engineering, Kyungpook National University, Daegu 41566, Korea.
| | - Bhum Jae Shin
- Department of Electronics Engineering, Sejong University, Seoul 05006, Korea.
| | - Heung-Sik Tae
- School of Electronics Engineering, College of IT Engineering, Kyungpook National University, Daegu 41566, Korea.
| |
Collapse
|
16
|
Effects of pulse current mode on plasma electrolytic oxidation of 7075 Al in Na2WO4 containing solution: From unipolar to soft-sparking regime. Electrochim Acta 2018. [DOI: 10.1016/j.electacta.2018.07.200] [Citation(s) in RCA: 38] [Impact Index Per Article: 6.3] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 12/22/2022]
|
17
|
|