Enhanced Photocatalytic Simultaneous Removals of Cr(VI) and Bisphenol A over Co(II)-Modified TiO2

Aryl selenonium vs. aryl sulfonium counterions in polyoxometalate chemistry: the impact of Se+ cationic centers on the photocatalytic reduction of dichromate

A selenonium organic counter ion has been used in polyoxometalate chemistry to develop a new aryl selenonium polyoxometalate (POM) hybrid, and its photocatalytic properties have been explored in comparison with an aryl sulfonium POM-hybrid counterpart for the first time. The chalcogenonium counterions, namely, methyldiphenylsulfonium trifluoromethane sulfonate (MDPST) and methyldiphenylselenonium trifluoromethane sulfonate (MDPSeT), and their octamolybdate ([Mo8O26]4-) hybrids, 1 and 2, with the general formula (C13H13X)4[Mo8O26] (where X = S for 1 and Se for 2) were synthesized and characterized. Hybrids 1 and 2 vary in their chalcogenonium cationic center (S+vs. Se+), which enabled a direct comparison of their photocatalytic properties as a function of the cationic center. The photocatalytic activities of hybrids 1 and 2 were tested using the reduction of dichromate (Cr2O72-) as a model reaction under UV irradiation. A 99% photocatalytic reduction of Cr2O72- with a rate constant of 0.0305 min-1 was achieved with hybrid 2, while only a 67% reduction with a rate constant of 0.0062 min-1 was observed with hybrid 1 in 180 minutes. The better catalytic performance of hybrid 2 may be correlated to the larger atomic radii of Se than S, which helps in better stabilizing the photogenerated electron-hole (e--h+) pair on the POM cluster by polarizing its lone pair more efficiently compared to S. The catalytic recyclability was tested for up to 4 cycles using hybrid 2, and up to 98% reduction was obtained even after the 4th cycle. Recyclability tests and control experiments also indicated the generation of some elemental Se through possible cleavage of some C-Se bonds of MDPSe under prolonged UV exposure during catalysis, and the Se thus generated was found to contribute to the catalytic reduction of dichromate. This study, therefore, opens new avenues for aryl selenonium moieties and their POM hybrids for potential catalytic applications.

Altass H, Althagafi II, Ahmed SA. Fabrication of Direct Z-Scheme CoNiWO4/Ph-gC3N4 Heterocomposites: Enhanced Photodegradation of Bisphenol A and Anticancer Activity

Photocatalysis is realized by the design of a visible-light-active catalyst with robust redox capacity and broad absorption. In this study, a series of novel Z-scheme CoNiWO4/Ph-gC3N4 photocatalysts are synthesized to improve their redox property and photocatalytic activity toward broad visible light absorption. An intimate stable heterojunction is made between cobalt-nickel tungstate (CoNiWO4) and phenyl-doped graphitic carbon nitride (Ph-gC3N4), and its physicochemical properties are studied. The bifunctional properties of all of the synthesized materials were assessed by studying the decomposition of bisphenol A (BPA) and methyl orange (MO) dye as model pollutants, followed by an evaluation of their anticancer activity on human lung cancer cell lines. The photocatalyst with 20 wt % CoNiWO4 heterocomposite showed an enhanced response toward the removal of cancerous cells. The synthesized pristine CoNiWO4 and Ph-gC3N4 exhibit well-matched band structures and, hence, make it easier to create a Z-scheme heterocomposite. This may increase the lifetime of photoinduced charge carriers with a high redox power, thereby improving their photocatalytic and anticancer activity. An extensive analysis of the mechanism demonstrates that hydroxyl radicals (•OH) and superoxide radical anions (•O2-) are responsible for the degradation of organic compounds via Z-scheme charge transfer approach. These findings point toward a new route for creating effective Co-Ni tungstate-based direct Z-scheme photocatalysts for various redox processes, particularly the mineralization of resistant organic molecules.

Titanium-Porphyrin Metal-Organic Frameworks as Visible-Light-Driven Catalysts for Highly Efficient Sonophotocatalytic Reduction of Cr(VI)

In this work, we synthesized and characterized four titanium-porphyrin metal-organic frameworks (MOFs) [DGIST-1(M), M = Co(II), Fe(III), Zn(II), and H₂] and used them as visible-light-driven catalysts for sonophotocatalytic Cr(VI) reduction. DGIST-1(M) exhibited open-framework, broad light absorption stemmed from ligand and sensitive photocurrent responses owing to the integration of one-dimensional Ti-oxo chains and 4-connected conjugated TCPP ligand (TCPP = tetrakis(4-carboxyphenyl)-porphyrin). DGIST-1(M) presented efficient reduction of Cr(VI) to Cr(III) in aqueous solution when used as sonophotocatalytic catalysts. The average reduction rates upon Cr(VI) were 0.920, 0.476, 0.377, and 0.194 mg·L^-1·min^-1 for DGIST-1(H₂), DGIST-1(Zn), DGIST-1(Co), and DGIST-1(Fe), which are 1.15-2.45 times higher than those in photocatalysis. Sonophotocatalytic experiments and electron paramagnetic resonance measurement proved that Ti-oxo chain units and porphyrin ligand in the structures of DGIST-1(M) existed as catalytic active centers for sonophotocatalytic reduction of Cr(VI). Photoluminescence and UV absorption spectra revealed that the unity of photocatalysis and sonochemistry strengthened the migration of photogenerated electrons from DGIST-1(M) to Cr(VI), which improved the activities of catalysts. This study suggested that the association of titanium-porphyrin MOFs and sonophotocatalytic technology is an impactful program for enhancing MOF-based photocatalytic systems.

Recent developments in architecturing the g-C3N4 based nanostructured photocatalysts: Synthesis, modifications and applications in water treatment

Water pollution is becoming an inevitable problem in today's world. Tons and tons of wastewater with hazardous pollutants are getting discharged into the clean water bodies every day. In this regard, photocatalytic environmental remediation using nanotechnology such as the use of organic, metal and non-metal based semiconductor photocatalysts for photodegradation of pollutants has gained enormous attention in the past few decades. This review is focused particularly on graphitic carbon nitride (g-C₃N₄) which is a cheap, metal-free, polymeric photoactive compound and it is used as a potential photocatalyst in wastewater treatment. Though, pristine g-C₃N₄ is a good photocatalyst, it has certain drawbacks such as poor visible light absorption capacity, quicker recombination of photoelectrons and holes, delayed mass and charge transfer, etc. As a result, the pristine g-C₃N₄ catalyst is modified into novel 0D, 1D, 2D and 3D morphologies such as nano-quantum dots, nanorods, nanotubes, nanowires, nanosheets, nanoflakes, nanospheres, nanoshells, etc. It was also tailored into novel composites along with various compounds through doping, metal deposition, heterojunction formation, etc., to enhance the photocatalytic property of pure g-C₃N₄. The modified catalysts showed promising photocatalytic performance such as degradation of majority of pollutants in the environment. It also showed excellent results in the removal or reduction of heavy metals. This review provides a detailed record of g-C₃N₄ and its diverse photocatalytic applications in the past years and it provides knowledge for the development of such similar novel compounds in the future.

Hydrogen Peroxide Activation with Sulfidated Zero-Valent Iron for Synchronous Removal of Cr(VI) and BPA

In this work, the synchronous removal of Cr(VI) and bisphenol A (BPA) in a heterogeneous Fenton process with sulfidated nanoscale zero-valent iron (S-nZVI) as the reductant and catalyst was systematically evaluated. Compared to other systems including S-nZVI or H2O2 alone, a simultaneous BPA degradation and Cr(VI) removal could be achieved in the S-nZVI/H2O2 system at an optimum pH of 3. It was, interestingly, found that 7.8% of BPA and 98.2% of Cr(VI) were removed within 60 min in presence of S-nZVI alone, whereas, correspondingly, 98.2% of BPA and 96.9% of Cr(VI) were eliminated in the S-nZVI/H2O2 system. Specifically, humic acid (HA) and H2PO4− inhibited the deterioration of BPA but posed no significant effect on Cr(VI) removal. NO3− had a slight lifting effect on the removal of BPA and Cr(VI), while HCO3− showed a relatively weak prohibition. Experiments with EPR and radical probe tests also provide direct evidence that hydroxyl radicals was monitored in the S-nZVI/H2O2 system, which not only degraded BPA but also inhibited the reduction of Cr(VI). It could not be ignored that FeS accelerated Fe0 corrosion to release Fe2+. In, addition, Fe0, Fe2+ and S2+ could react with Cr(VI) while the most of produced Cr(III) was co-precipitated in the form of CrxFe1−xOOH film. The study confirmed that it was feasible for S-nZVI/H2O2 system to remove synchronously organic pollutants and heavy metal.

A facile approach to synthesize CdS-attapulgite as a photocatalyst for reduction reactions in water

At room temperature, a facile approach has been utilized for preparing novel CdS–attapulgite (CdS–ATP) composites and the composites were applied in photocatalytic reduction of p-nitrophenol and Cr(vi). The effect of ATP on the photocatalytic activity of the CdS–ATP composites were studied by controlling the mass ratio of attapulgite. The results showed that the CdS–20%ATP composite has an excellent photocatalytic activity. In order to figure out the key to improve the photocatalytic efficiency, the prepared composites were characterized by Brunauer–Emmett–Teller (BET) specific surface area, UV-vis diffuse reflectance spectroscopy (DRS) and electrochemical impedance spectroscopy (EIS). The superior photocatalytic performance of the CdS–20%ATP composite can be ascribed to the existence of the ATP which can fix the CdS and prevent agglomeration. The interaction between ATP and CdS in the composites facilitates the electron transfer and also promoted their photocatalytic performance. This work provides us with some significant guidance in the development of CdS–ATP composite photocatalysts.

The application of CdS–attapulgite composites in photocatalytic reduction of p-nitrophenol and Cr(vi) demonstrated that the attapulgite could overcome the limitations of CdS.

Self-Assembly of Poly(ethyleneimine)-Modified g-C3N4 Nanosheets with Lysozyme Fibrils for Chromium Detoxification

We disclose a straightforward approach to fabricate nanocomposites for efficient capture of Cr(VI) from an aqueous solution through the self-assembly of poly(ethyleneimine)-modified graphitic carbon nitride nanosheets (PEI-g-C₃N₄ NSs) and lysozyme fibrils (LFs). The as-made PEI-g-C₃N₄ NSs@LFs exhibited mesoporous structures with a high specific surface area of 39.6 m² g^-1, a large pore volume of 0.25 cm³ g^-1, several functional groups (e.g., -N, -NH, -NH₂, and -COOH), and a zero-point charge at pH 9.1. These merits allow the PEI-g-C₃N₄ NSs@LFs to further enhance their physical adsorption and electrostatic attraction with the negatively charged Cr(VI) species of HCrO₄^- and CrO₄^2-, which is beneficial for the uptake of Cr(VI), >80%, from an aqueous solution in a wide pH range. Interestingly, X-ray photoelectron spectra indicate that the PEI-g-C₃N₄ NSs@LFs converted Cr(VI) to Cr(III) through visible-light-induced photoreduction. The adsorption of Cr(VI) on the surface of PEI-g-C₃N₄ NSs@LFs was found to obey the Freundlich isotherm model, signifying that they have a heterogeneous surface for the multilayer uptake of Cr(VI). In contrast, the PEI-g-C₃N₄ NSs and LFs as Cr(VI) adsorbents followed the Langmuir isotherm model. Adsorption kinetic studies showed that the uptake of Cr(VI) through the PEI-g-C₃N₄ NSs@LFs was highly correlated with a pseudo-first-order model, suggesting that physisorption dominates the interaction of Cr(VI) and the PEI-g-C₃N₄ NSs@LFs. In real-life applications, the PEI-g-C₃N₄ NSs@LFs were used for the detoxification of the total chromium in the industrial effluent and sludge samples.

Pyrolytic synthesis of organosilane-functionalized carbon nanoparticles for enhanced photocatalytic degradation of methylene blue under visible light irradiation

The use of carbon-based nanomaterials as effective photocatalysts is an ideal alternative for environmental remediation. Here, (3-aminopropyl)triethoxysilane-functionalized carbon nanoparticles (SiCNPs) were prepared using a simple pyrolysis method with sodium citrate and urea as the precursors. The samples were characterized by X-ray diffraction, transmission electron microscopy, ultraviolet-visible diffuse reflectance spectroscopy, X-ray photoelectron spectroscopy, photoluminescence spectroscopy, and photo-electrochemical measures. The obtained SiCNPs-2.0 showed a better visible light response and more effective photocatalytic activity for degradation of methylene blue (MB) compared with pure CNPs. Under visible light irradiation, 98.8% of the MB was decomposed within 75 min when SiCNPs-2.0 was used as the photocatalyst. The high photocatalytic activities of SiCNPs-2.0 could be attributed to enhanced light absorption in the visible region, and improved photogenerated electron-hole separation efficiency. A possible photocatalytic mechanism for removal of MB over SiCNPs-2.0 was proposed based on active species trapping experiments. Recycling experiments showed that SiCNPs-2.0 had good stability during photocatalysis. This work provides a new easy method to synthesize carbon-based nanomaterials and to catalytically degrade organic pollutants in water under visible light irradiation.

Preferentially oriented Ag-TiO2 nanotube array film: An efficient visible-light-driven photocatalyst

Ag-TiO₂ nanotube array films with the preferential orientation of crystals were fabricated on ITO glass by magnetron sputtering and anodization. Comprehensive characterization was performed to ascertain the composition and microstructure characteristics of thin films. The photocatalytic activities were evaluated through the reduction of hexavalent chromium (Cr₂O₇^2- (Cr (VI)) as a model compound under visible light irradiation. XRD and XPS studies reveal the development of preferred orientation along [001] in anatase TiO₂ nanotubes by adjusting the Ag content during magnetron sputtering. Such unusual behavior is attributed to the minimization of anatase (001) surface energy assisted by Ag. The Ag-TiO₂ nanotube arrays having preferred crystal orientation exhibit superior separation/transfer of photo-induced charges. Furthermore, the Ag-TiO₂ nanotube arrays show improved absorption of visible light due to the SPR effect induced by Ag and the formation of heterojunction between the TNAs and Ag₂O. TNA-3Ag exhibits the highest photocatalytic activities by removing 99.1 % Cr (VI) in 90 min under visible light illumination.

Synthesis and fabrication of g-C3N4-based materials and their application in elimination of pollutants

With the fast development of industrial and human activity, large amounts of persistent organic pollutants, heavy metal ions and radionuclides are released into the natural environment, which results in environmental pollution. The efficient elimination of the natural environment is crucial for the protection of environment to against the pollutants' toxicity to human beings and living organisms. Graphitic carbon nitride (g-C₃N₄) has drawn multidisciplinary attention especially in environmental pollutants' cleanup due to its special physicochemical properties. In this review, we summarized the recent works about the synthesis of g-C₃N₄, element-doping, structure modification of g-C₃N₄ and g-C₃N₄-based materials, and their application in the sorption, photocatalytic degradation and reduction-solidification of persistent organic pollutants and heavy metal ions. The interaction mechanisms were discussed from advanced spectroscopic analysis and computational approaches at molecular level. The challenges and future perspectives of g-C₃N₄-based materials' application in environmental pollution management are presented in the end. This review highlights the real applications of g-C₃N₄-based materials as adsorbents or photocatalysts in the adsorption-reduction-solidification of metal ions or photocatalytic degradation of organic pollutants. The contents are helpful for the undergraduate students to understand the recent works in the elimination of organic/inorganic pollutants in their pollution management.

Controlled Growth of LDH Films with Enhanced Photocatalytic Activity in a Mixed Wastewater Treatment

Due to multiple charge transport pathways, adjustable layer spacing, compositional flexibility, low manufacturing cost, and absorption of visible light, layered double hydroxides (LDHs) are a promising material for wastewater treatment. In this study, LDH films and Fe-doped LDH films with different metal ions (Ni, Al, Fe) on the surface of conductive cloth were successfully prepared and applied for the photocatalytic degradation of wastewater containing methyl orange and Ag ions under visible-light irradiation. The chemical state of Fe ions and the composition of LDHs on methyl orange photodegradation were investigated. The experimental results showed that LDH films exhibited high photocatalytic activity. The photocatalytic activity of LDH films on methyl orange improved in the mixed wastewater, and the Fe-doped NiAl-LDH films exhibited best visible-light photocatalytic performance. The analysis showed that Ag ions in the mixed wastewater were reduced by the LDH films and subsequently deposited on the surface of the LDH films. The Ag nanoparticles acted as electron traps and promoted the photocatalytic activity of the LDH films on methyl orange. Thus, we have demonstrated that prepared LDH films can be used in the treatment of mixed wastewater and have broad application prospects in environmental remediation and purification processes.