Plastic-Like Supramolecular Hydrogels with Polyelectrolyte/Surfactant Complexes as Physical Cross-links

Insights into the assembly process and properties of regenerated cellulose beads prepared in alkali/urea aqueous solutions

Taking the perspective of cellulose molecular chain assembly via the "bottom-top" route, we delve into the influence of both the cellulose solution and the coagulation bath on the assembly process and structure of regenerated cellulose beads (RCBs). The results show that cellulose molecular weight, mass fraction, and the presence of surfactant have an impact on RCBs. Contrary to traditional views where the structures of material are determined by solvent-nonsolvent exchange rate, ion-cellulose binding capacity also affects RCBs. Overall, the influence of ions follows the Hofmeister sequence. Kosmotropes promote the assembly of cellulose chains and elementary fibers, leading to "salting out" effects, reduced pore size of RCBs, increased crystallinity, and enhanced mechanical properties. In contrast, chaotropes induce "salting in" effects, resulting in opposite outcomes. The average pore size of RCBs coagulated in NaSCN solution was approximately 15-folds larger than those prepared in sodium citrate solution. Anions have a greater impact than cations, and both "salting out" and "salting in" effects strengthen with concentration. Temperature variations primarily affect solvent and nonsolvent exchange speed during cellulose regeneration. These findings provide new insights into regulating RCBs, enabling tailored performance for different applications.

High Breakthrough Pressure in Hydrogels Enabled Ultrastable Treatment of Hypersaline Wastewaters

Surface effects of low-surface-tension contaminants accumulating at the evaporation surface easily induce wetting in membrane distillation, especially in hypersaline scenarios. Herein, we propose a novel strategy to eliminate the surface effect and redistribute contaminants at the evaporation interface simply by incorporating a layer of hydrogel. The as-fabricated composite membrane exhibits remarkable stability, even when exposed to solution with salt concentration of 5 M and surfactant concentration of 8 mM. Breakthrough pressure of the membrane reaches 20 bar in the presence of surfactants, surpassing commercial hydrophobic membranes by one to two magnitudes. Density functional theory and molecular dynamics simulations reveal the important role of the hydrogel-surfactant interaction in suppressing the surface effect. As a proof of concept, we demonstrate the membrane in stably processing synthetic wastewater containing 144 mg L-1 surfactants, 1 g L-1 mineral oils, and 192 g L-1 NaCl, showing its potential in addressing challenges of hypersaline water treatment.

Unconventional luminescent CS-PEC-based composite hemostasis sponge with antibacterial activity and visual monitoring for wound healing

Multifunctional wound dressings are promising medical materials for various applications. Among them, dressings with antimicrobial activity, high biosafety, and real-time monitoring have attracted considerable research interest. Herein, a biodegradable hemostatic sponge comprising a chitosan skeleton and polyelectrolyte-surfactant complex (CS-PEC) was developed as a versatile wound dressing for wound pH monitoring and inhibition of bacterial infection. CS-PEC sponge with high porosity exhibited satisfactory fluid absorption capacity and biocompatibility, along with antibacterial properties against E. coli and S. aureus. In vivo experiments in rat liver trauma model revealed that wounds treated with the CS-PEC sponge recorded less blood loss (97.1 mg) and shorter hemostasis time (27.2 s) than those treated with commercial gelatin sponge (309.1 mg and 163.5 s, respectively). Furthermore, PECs based on unconventional luminescent molecules (L-C16-Hyp) were used as pH fluorescent indicators, which endowed the sponge with fluorescence-responsive behavior to wound pH changes in the range of 5.0-8.5. Visual images can be captured using a smartphone and converted to RGB color mode values for on-site assessment of wound status. This study sheds light on the design and application of unconventional luminescent materials in wound dressing and provides a smart and effective solution for wound management.

Polyelectrolyte Complex Hydrogels from Controlled Kneading and Annealing-Induced Tightly Wound and Highly Entangled Natural Polysaccharides

Hydrogels usually are fabricated by using monomers or preexisting polymers in precursor solutions. Here, a polyelectrolyte complex biohydrogel (Bio-PEC hydrogel) made from a precursor dough, by kneading, annealing, and crosslinking the dough of two oppositely charged polysaccharides, cationic chitosan quaternary ammonium salt (HACC) and anionic sodium hyaluronate (HA), photoinitiator (α-ketoglutaric acid), crosslinker glycidyl methacrylate (GMA), and water of very small quantity is reported. Controlled kneading and annealing homogenized the dough with respect to transforming randomly distributed, individual polymer chains into tightly wound double-stranded structures, which, upon UV irradiation, covalently sparsely crosslinked into a highly entangled network and subsequently, upon fully swollen in water, results in Bio-PEC hydrogel, HACC/HA, exhibiting near-perfect elasticity, high tensile strength, and high swelling resistance. Via the same kneading and annealing, tetracarboxyphenylporphyrin iron (Fe-TCPP) metal nanoclusters are incorporated into HACC/HA to obtain photocatalytic, antibacterial, and biocompatible Bio-PEC hydrogel composite, Fe-TCPP@HACC/HA. Using SD rat models, the efficacy of Fe-TCPP@HACC/HA in inhibiting Escherichia coli (E. coli) growth in vitro and the ability to promote wound healing and scar-free skin regeneration in vivo, or its high potential as a wound dressing material for biomedical applications are demonstrated.

Amphiphilic monomers bridge hydrophobic polymers and water

Water dissolves a hydrophilic polymer, but not a hydrophobic polymer. Many monomers of hydrophilic polymers, however, are amphiphilic, with a hydrophobic vinyl group for radical polymerization, as well as a hydrophilic group. Consequently, such an amphiphilic monomer may form solutions with both water and hydrophobic polymers. Ternary mixtures of amphiphilic monomer, hydrophobic polymer, and water have recently been used as precursors for interpenetrating polymer networks of hydrophilic polymers and hydrophobic polymers of unusual properties. However, the phase behavior of the ternary mixtures of amphiphilic monomer, hydrophobic polymer, and water themselves has not been studied. Here we mix the amphiphilic monomer acrylic acid, the hydrophobic polymer poly(methyl methacrylate), and water. In the mixture, the hydrophobic polymer can form various morphologies, including solution, micelle, gel, and polymer glass. We interpret these findings by invoking that the hydrophobic and hydrophilic groups of the amphiphilic monomer enable it to function as a bridge. That is, the hydrophobic functional group binds with the hydrophobic polymer, and the hydrophilic functional group binds with water. This picture leads to a simple modification to the Flory-Huggins theory, which agrees well with our experimental data. Amphiphilic monomers offer a rich area for further study for scientific insight, as well as for expanding opportunities to develop materials of self-assembled structures with unusual properties.

Biomedical applications of supramolecular hydrogels with enhanced mechanical properties

Supramolecular hydrogels bound by hydrogen bonding, host-guest, hydrophobic, and other non-covalent interactions are among the most attractive biomaterials available. Supramolecular hydrogels have attracted extensive attention due to their inherent dynamic reversibility, self-healing, stimuli-response, excellent biocompatibility, and near-physiological environment. However, the inherent contradiction between non-covalent interactions and mechanical strength makes the practical application of supramolecular hydrogels a great challenge. This review describes the mechanical strength of hydrogels mediated by supramolecular interactions, and focuses on the potential strategies for enhancing the mechanical strength of supramolecular hydrogels and illustrates their applications in related fields, such as flexible electronic sensors, wound dressings, and three-dimensional (3D) scaffolds. Finally, the current problems and future research prospects of supramolecular hydrogels are discussed. This review is expected to provide insights that will motivate more advanced research on supramolecular hydrogels.

Dual Lewis Acid- and Base-Responsive Terpyridine-Based Hydrogel: Programmable and Spatiotemporal Regulation of Fluorescence for Chemical-Based Information Security

A huge amount of data inundated in our daily life; there is an ever-increasing need to develop a new strategy of information encryption-decryption-erasing. Herein, a polymeric DCTpy/PAM hydrogel has been fabricated to store information via controllable Eu³⁺/Zn²⁺ ionoprinting for hierarchical and multidimensional information decryption. Eu³⁺ and Zn²⁺ have a competition and dynamic interaction toward DCTpy under NH₃ stimuli in the polymeric DCTpy/PAM hydrogel network. The Eu(III)/Zn(II)@DCTpy/PAM hydrogel exhibits light red fluorescence of Eu³⁺ due to the antenna effect. Upon the addition of NH₃, dissociation of the Eu³⁺-DCTpy complex takes place, and the Zn(II)/DCTpy/NH₃ complex is formed with both ICT (intramolecular charge-transfer) and PET (photo-induced electron-transfer) process characteristics that exhibits yellow emission color. Subsequently, HCl can quench the fluorescence of the resulting hydrogel. By integrating transparency, adhesiveness, and programmable stimuli responsiveness of the hydrogel blocks in to one system, complex, multistage, and time-controlled information storage-encryption-decryption-erasing in sequence with multidimensions is illustrated via the molecule diffusion method. This work provides a novel and representative strategy in fabricating information encryption-decryption-erasing materials with high capacity and complexity by a simple terpyridine-based hydrogel.

Noncovalently Cross-Linked Polymeric Materials Reinforced by Well-Designed In Situ-Formed Nanofillers

Noncovalently cross-linked polymeric materials generally exhibit lower mechanical robustness than traditional polymeric materials. Therefore, it is important to improve the mechanical properties of noncovalently cross-linked polymeric materials using an efficient and generalized approach. In this Perspective, we systematically summarized the recent development of noncovalently cross-linked polymeric materials reinforced by in situ-formed nanofillers. The synergy of high-density noncovalent interactions and in situ-formed rigid nanofillers provided an effective means for the fabrication of noncovalently cross-linked plastics with high mechanical strength. The design of in situ-formed tough nanofillers, which could deform and dissociate, endowed the noncovalently cross-linked hydrogels and elastomers with high toughness, excellent stretchability, elasticity, damage resistance, and damage tolerance. Benefiting from the well-designed in situ-formed nanofillers, these noncovalently cross-linked polymeric materials with enhanced mechanical strength still exhibited satisfactory healing, recycling, and reprocessing properties. Outlooks were provided to envision the remaining challenges to the further development and practical application of noncovalently cross-linked polymeric materials reinforced with in situ-formed nanofillers.

Hydrogen-Bonding Affords Sustainable Plastics with Ultrahigh Robustness and Water-Assisted Arbitrarily Shape Engineering

Herein, the supramolecular plastic-like hydrogel (SPH) is introduced as a platform to fabricate sustainable plastics with ultrahigh stiffness and strength as well as water-assisted arbitrarily shapeable capability. The transparent plastics are constructed from SPHs of cellulose ether/polycarboxylic acid complexes and demonstrate mechanical robustness with Young's modulus up to 3.4 GPa and tensile strength up to 124.0 MPa, superior or comparable to most common plastics. Meanwhile, the shape of the plastics can be reversibly engineered by air drying of the SPHs with diverse 2D/3D shapes and structures, which are generated conveniently via origami, kirigami, embossing, etc., in virtue of plastic deformation and shape memory effect of SPHs. On the basis of multi-dimensional infrared-spectral analysis, it is revealed that the dense acid-acid and acid-ether hydrogen (H)-bonding network in the plastic is responsible for the mechanical robustness while the evolution of water-polymer H-bonds into polymer-polymer H-bonds during air drying contributes to the shape fixing. This work provides a novel method of manufacturing sustainable plastics with simultaneous strong mechanical performance and convenient processibility from hydrogels with plastic-like mechanical behavior.

Highly Impact-Resistant Block Polymer-Based Thermoplastic Elastomers with an Ionically Functionalized Rubber Phase

There has been a great deal of interest in incorporating noncovalent bonding groups into elastomers to achieve high strength. However, the impact resistance of such elastomers has not been evaluated, even though it is a crucial mechanical property in practical usage, partly because a large-scale synthetic scheme has not been established. By ionizing the rubber component in polystyrene-b-polyisoprene-b-polystyrene (SIS), we prepared several tens of grams of SIS-based elastomers with an ionically functionalized rubber phase and a sodium cation (i-SIS(Na)) or a bulky barium cation (i-SIS(Ba)). The i-SIS(Na) and i-SIS(Ba) exhibited very high tensile toughness of 520 and 280 MJ m-3, respectively. They also exhibited excellent compressive resistance. Moreover, i-SIS(Ba) was demonstrated to have a higher impact resistance, that is, more protective of a material being covered compared to covering by typical high-strength glass fiber-reinforced plastic. As such elastomers can be produced at an industrial scale, they have great market potential as next-generation elastomeric materials.

Synergic influences of network topologies and associative interactions on the microstructures and bulk performances of hydrogels

Revealing the relationship between network topologies and mechanical properties of hydrogels is fundamental yet challenging in the design of tough soft materials. Here, we report a series of hydrogels using N-isopropyl acrylamide (NIPAm) and acrylic acid (AAc) as the basic units to form a single network of the copolymer, a semi-interpenetrated network of two homopolymers, and a grafted network with homopolymer chains anchored on another homopolymer network, to investigate the influence of network architectures on the mechanical properties and thermal responses of the gels. We found that the properties of the gels are also significantly influenced by the formation of hydrogen bonds between poly(N-isopropyl acrylamide) (PNIPAm) and poly(acrylic acid) (PAAc) segments. The gels with the single network of poly(NIPAm-co-AAc) are mechanically weak due to the low efficiency for forming robust hydrogen bonds, while micro-segregated domains are formed in the hydrogels with a semi-interpenetrated network structure due to the formation of inter-chain hydrogen bonds that favors energy dissipation and toughening of the gels. On the other hand, dense hydrogen bonds form between the grafted PNIPAm chains and the PAAc network, resulting in nano-segregated domains and excellent mechanical properties of the gels. The hydrogels with the grafted network structure exhibit a more repeatable response to temperature than those with the semi-interpenetrated network structure due to the relatively stable hydrogen-bond network. The comparison of the mechanical properties and thermal stability of the hydrogels with the same composition but different topological networks should be informative for engineering hydrogel properties or functions by tailoring the network structures.