Time-Resolved SAXS Studies of the Kinetics of Thermally Triggered Release of Encapsulated Silica Nanoparticles from Block Copolymer Vesicles

Degradable Block Copolymer Nanoparticles Synthesized by Polymerization-Induced Self-Assembly

Polymerization-induced self-assembly (PISA) combines polymerization and in situ self-assembly of block copolymers in one system and has become a widely used method to prepare block copolymer nanoparticles at high concentrations. The persistence of polymers in the environment poses a huge threat to the ecosystem and represents a significant waste of resources. There is an urgent need to develop novel chemical approaches to synthesize degradable polymers. To meet with this demand, it is crucial to install degradability into PISA nanoparticles. Most recently, degradable PISA nanoparticles have been synthesized by introducing degradation mechanisms into either shell-forming or core-forming blocks. This Minireview summarizes the development in degradable block copolymer nanoparticles synthesized by PISA, including shell-degradable, core-degradable, and all-degradable nanoparticles. Future development will benefit from expansion of polymerization techniques with new degradation mechanisms and adaptation of high-throughput approaches for both PISA syntheses and degradation studies.

3D printable, thermo-responsive, self-healing, graphene oxide containing self-assembled hydrogels formed from block copolymer wormlike micelles

Graphene oxide (GO) containing block copolymer nanocomposite hydrogels formed from poly(glycerol monomethacrylate-block-hydroxypropyl methacrylate) (PGMA-PHPMA) wormlike micelles were prepared by either mixing GO and copolymer at low temperature or via in situ reversible addition-fragmentation chain-transfer (RAFT) polymerisation-induced self-assembly (PISA) of HPMA in the presence of a PGMA macromolecular chain-transfer agent and GO flakes. Hydrogels containing 15-25% w/w copolymer and 0 and 8% w/w GO, based on copolymer, were investigated and the maximum gel strength measured was ∼33 kPa for a 25% w/w copolymer gel prepared by in situ polymerisation and containing 2% w/w GO based on copolymer. This gel strength represents a fifteen-fold increase over the same copolymer gel without the addition of GO. The nanocomposite gels were found to recover efficiently after the application of high shear, with up to 98% healing efficiency within seconds. These gels are also 3D printable, self-healing, adhesive and temperature responsive on cooling and re-heating. The observed properties were both GO and copolymer concentration dependent, and tensile testing demonstrated that the nanocomposite gels had higher moduli, elongation at break and toughness than gels prepared without GO.

Assessment of core-shell nanoparticles surface structure heterogeneity by SAXS contrast variation and ab initio modeling

For the biomedical applications of nanoparticles, the study of their structure is a major step towards understanding the mechanisms of their interaction with biological environment. Detailed structural analysis of particles' surface is vital for rational design of drug delivery systems. In particular, for core-shell or surface-modified nanoparticles surface structure can be described in terms of shell coating uniformity and shell thickness uniformity around the nanoparticle core. Taken together, these terms can be used to indicate degree of heterogeneity of nanoparticle surface structure. However, characterization of nanoparticle surface structure under physiological conditions is challenging due to limitations of experimental techniques. In this paper, we apply SAXS contrast variation combined with ab initio bead modeling for this purpose. Approach is based on the fact that nanoparticles under study are produced by self-assembly of phospholipid-conjugated molecules that possess moieties with significantly different electron densities enabling SAXS technique to be used to distinguish nanoparticle shell and study its structure. Ab initio single phase and ab initio multiphase modeling based on SAXS curve of nanoparticles in phosphate buffer solution allowed to reconstruct nanoparticle shell coating and assess its uniformity, while serial nanoparticle reconstructions from solutions with gradually increased solvent electron densities revealed relative shell coating thickness around nanoparticle core. Nanoparticle shell structure representation was verified by molecular dynamics simulation and derived full-atom nanoparticle shell structure showed good agreement with SAXS-derived representation. Obtained data indicate that studied nanoparticles exhibit highly heterogeneous surface structure.

Shape-Shifting Thermoresponsive Block Copolymer Nano-Objects

In this Feature Article, we review our recent progress in the design of shape-shifting thermoresponsive diblock copolymer nano-objects, which are prepared using various hydroxyl-functional (meth)acrylic monomers (e.g. 2‑hydroxypropyl methacrylate, 4‑hydroxybutyl acrylate or hydroxybutyl methacrylate) to generate the thermoresponsive block. Unlike traditional thermoresponsive polymers such as poly(N-isopropylacrylamide), there is no transition between soluble and insoluble polymer chains in aqueous solution. Instead, thermally driven transitions between a series of copolymer morphologies (e.g. spheres, worms, vesicles or lamellae) occur on adjusting the aqueous solution temperature owing to a subtle change in the partial degree of hydration of the permanently insoluble thermoresponsive block. Such remarkable self-assembly behavior is unprecedented in colloid science: no other amphiphilic diblock copolymer or surfactant system undergoes such behavior at a fixed chemical composition and concentration. Such shape-shifting nano-objects are characterized by transmission electron microscopy, dynamic light scattering, small-angle X-ray scattering, rheology and variable temperature ¹H NMR spectroscopy. Potential applications for this fascinating new class of amphiphiles are briefly considered.

Serial small- and wide-angle X-ray scattering with laboratory sources

Recent advances in X-ray instrumentation and sample injection systems have enabled serial crystallography of protein nanocrystals and the rapid structural analysis of dynamic processes. However, this progress has been restricted to large-scale X-ray free-electron laser (XFEL) and synchrotron facilities, which are often oversubscribed and have long waiting times. Here, we explore the potential of state-of-the-art laboratory X-ray systems to perform comparable analyses when coupled to micro- and millifluidic sample environments. Our results demonstrate that commercial small- and wide-angle X-ray scattering (SAXS/WAXS) instruments and X-ray diffractometers are ready to access samples and timescales (≳5 ms) relevant to many processes in materials science including the preparation of pharmaceuticals, nanoparticles and functional crystalline materials. Tests of different X-ray instruments highlighted the importance of the optical configuration and revealed that serial WAXS/XRD analysis of the investigated samples was only possible with the higher flux of a microfocus setup. We expect that these results will also stimulate similar developments for structural biology.

Reverse sequence polymerization-induced self-assembly in aqueous media: a counter-intuitive approach to sterically-stabilized diblock copolymer nano-objects

A 500 nm charge-stabilized latex is converted into 40 nm sterically-stabilized nanoparticles via reverse sequence polymerization-induced self-assembly (PISA).

Organic–inorganic hybrid nanomaterials prepared via polymerization-induced self-assembly: recent developments and future opportunities

This review highlights recent developments in the preparation of organic–inorganic hybrid nanomaterials via polymerization-induced self-assembly.

Silica nanoparticle-loaded thermoresponsive block copolymer vesicles: a new post-polymerization encapsulation strategy and thermally triggered release

A thermoresponsive amphiphilic diblock copolymer that can form spheres, worms or vesicles in aqueous media at neutral pH by simply raising the dispersion temperature from 1 °C (spheres) to 25 °C (worms) to 50 °C (vesicles) is prepared via polymerization-induced self-assembly (PISA). Heating such an aqueous copolymer dispersion from 1 °C up to 50 °C in the presence of 19 nm glycerol-functionalized silica nanoparticles enables this remarkable ‘shape-shifting’ behavior to be exploited as a new post-polymerization encapsulation strategy. The silica-loaded vesicles formed at 50 °C are then crosslinked using a disulfide-based dihydrazide reagent. Such covalent stabilization enables the dispersion to be cooled to room temperature without loss of the vesicle morphology, thus aiding characterization and enabling the loading efficiency to be determined as a function of both copolymer and silica concentration. Small-angle X-ray scattering (SAXS) analysis indicated a mean vesicle membrane thickness of approximately 20 ± 2 nm for the linear vesicles and TEM studies confirmed encapsulation of the silica nanoparticles within these nano-objects. After removal of the non-encapsulated silica nanoparticles via multiple centrifugation–redispersion cycles, thermogravimetric analysis indicated that vesicle loading efficiencies of up to 86% can be achieved under optimized conditions. Thermally-triggered release of the silica nanoparticles is achieved by cleaving the disulfide bonds at 50 °C using tris(2-carboxyethyl)phosphine (TCEP), followed by cooling to 20 °C to induce vesicle dissociation. SAXS is also used to confirm the release of silica nanoparticles by monitoring the disappearance of the structure factor peak arising from silica–silica interactions.

A loading efficiency of up to 86% is achieved for silica nanoparticles encapsulated within crosslinkable redox-sensitive thermoresponsive diblock copolymer vesicles in water at 50 °C; triggered release is also demonstrated for this system.

Encapsulation by Directed PISA: RAFT-Based Polymer-Vesiculated Pigment for Opacity Enhancement in Paint Films

A novel method is demonstrated to encapsulate titanium dioxide pigment using directed polymerization-induced self-assembly (PISA) with reversible addition-fragmentation chain-transfer (RAFT) controlled emulsion polymerization. The polymerization is carried out in a batch process in which both styrene (Sty) and the pigment are emulsified using triblock amphiphilic macro-RAFT copolymers as stabilizers. RAFT-controlled chain growth leads to directed lamellar self-assembly, forming polystyrene (PS) shells' encapsulating pigment particles with 100% efficiency. The pigment resides either at centers of single-void vesicles or within the interior of multivoid vesiculated particles. The presence of complex morphologies such as spherical particles, nanofibers, nanoplatelets, and polymer vesicles confirms the PISA pathway. The process is optimized to preferably produce polymer-vesiculated pigment for use as an enhanced opacifier in water-based paint.

In situ SAXS studies of a prototypical RAFT aqueous dispersion polymerization formulation: monitoring the evolution in copolymer morphology during polymerization-induced self-assembly

Small-angle X-ray scattering (SAXS) is used to characterize the in situ formation of diblock copolymer spheres, worms and vesicles during reversible addition-fragmentation chain transfer (RAFT) aqueous dispersion polymerization of 2-hydroxypropyl methacrylate at 70 °C using a poly(glycerol monomethacrylate) steric stabilizer. 1H NMR spectroscopy indicates more than 99% HPMA conversion within 80 min, while transmission electron microscopy and dynamic light scattering studies are consistent with the final morphology being pure vesicles. Analysis of time-resolved SAXS patterns for this prototypical polymerization-induced self-assembly (PISA) formulation enables the evolution in copolymer morphology, particle diameter, mean aggregation number, solvent volume fraction, surface density of copolymer chains and their mean inter-chain separation distance at the nanoparticle surface to be monitored. Furthermore, the change in vesicle diameter and membrane thickness during the final stages of polymerization supports an 'inward growth' mechanism.

Factors affecting the morphology of some organic and inorganic nanostructures for drug delivery: characterization, modifications, and toxicological perspectives

Introduction: In this review, we aim to highlight the impact of various processes and formulation variables influencing the characteristics of certain surfactant-based nanoconstructs for drug delivery. Areas covered: The review includes the discussion on processing parameters for the preparation of nanoconstructs, especially those made up of surfactants. Articles published in last 15 years (437) were reviewed, 381 articles were selected for data review and most appropriate articles (215) were included in article. Effect of variables such as surfactant concentration and type, membrane additives, temperature, and pH-dependent transitions on morphology has been highlighted along with effect of shape on nanoparticle uptake by cells. Various characterization techniques explored for these nanostructures with respect to size, morphology, lamellarity, distribution, etc., and a separate section on polymeric vesicles and the influence of block copolymers, type of block copolymer, control of block length, interaction of multiple block copolymers on the structure of polymersomes and chimeric nanostructures have been discussed. Finally, applications, modification, degradation, and toxicological aspects of these drug delivery systems have been highlighted. Expert opinion: Parameters influencing the morphology of micelles and vesicles can directly or indirectly affect the efficacy of small molecule cellular internalization as well as uptake in the case of biologicals.[Figure: see text].

Potent and Prolonged Innate Immune Activation by Enzyme-Responsive Imidazoquinoline TLR7/8 Agonist Prodrug Vesicles

Synthetic immune-stimulatory drugs such as agonists of the Toll-like receptors (TLR) 7/8 are potent activators of antigen-presenting cells (APCs), however, they also induce severe side effects due to leakage from the site of injection into systemic circulation. Here, we report on the design and synthesis of an amphiphilic polymer-prodrug conjugate of an imidazoquinoline TLR7/8 agonist that in aqueous medium forms vesicular structures of 200 nm. The conjugate contains an endosomal enzyme-responsive linker enabling degradation of the vesicles and release of the TLR7/8 agonist in native form after endocytosis, which results in high in vitro TLR agonist activity. In a mouse model, locally administered vesicles provoke significantly more potent and long-lasting immune stimulation in terms of interferon expression at the injection site and in draining lymphoid tissue compared to a nonamphiphilic control and the native TLR agonist. Moreover, the vesicles induce robust activation of dendritic cells in the draining lymph node in vivo.

Synchrotron Scattering Methods for Nanomaterials and Soft Matter Research

This article aims to provide an overview of broad range of applications of synchrotron scattering methods in the investigation of nanoscale materials. These scattering techniques allow the elucidation of the structure and dynamics of nanomaterials from sub-nm to micron size scales and down to sub-millisecond time ranges both in bulk and at interfaces. A major advantage of scattering methods is that they provide the ensemble averaged information under in situ and operando conditions. As a result, they are complementary to various imaging techniques which reveal more local information. Scattering methods are particularly suitable for probing buried structures that are difficult to image. Although, many qualitative features can be directly extracted from scattering data, derivation of detailed structural and dynamical information requires quantitative modeling. The fourth-generation synchrotron sources open new possibilities for investigating these complex systems by exploiting the enhanced brightness and coherence properties of X-rays.

Recent advances in colloidal nanocomposite designviaheterogeneous polymerization techniques

Recent advances in colloidal nanocomposite design by heterogeneous polymerization are reviewed, with a specific focus on encapsulation and particle-based stabilization for specific materials applications.

Polymersomes: Breaking the Glass Ceiling?

Polymer vesicles, also known as polymersomes, have garnered a lot of interest even before the first report of their fabrication in the mid-1990s. These capsules have found applications in areas such as drug delivery, diagnostics and cellular models, and are made via the self-assembly of amphiphilic block copolymers, predominantly with soft, rubbery hydrophobic segments. Comparatively, and despite their remarkable impermeability, glassy polymersomes (GPs) have been less pervasive due to their rigidity, lack of biodegradability and more restricted fabrication strategies. GPs are now becoming more prominent, thanks to their ability to undergo stable shape-change (e.g., into non-spherical morphologies) as a response to a predetermined trigger (e.g., light, solvent). The basics of block copolymer self-assembly with an emphasis on polymersomes and GPs in particular are reviewed here. The principles and advantages of shape transformation of GPs as well as their general usefulness are also discussed, together with some of the challenges and opportunities currently facing this area.

Controlling Nanomaterial Size and Shape for Biomedical Applications via Polymerization-Induced Self-Assembly

Rapid developments in the polymerization-induced self-assembly (PISA) technique have paved the way for the environmentally friendly production of nanoparticles with tunable size and shape for a diverse range of applications. In this feature article, the biomedical applications of PISA nanoparticles and the substantial progress made in controlling their size and shape are highlighted. In addition to early investigations into drug delivery, applications such as medical imaging, tissue culture, and blood cryopreservation are also described. Various parameters for controlling the morphology of PISA nanoparticles are discussed, including the degree of polymerization of the macro-CTA and core-forming polymers, the concentration of macro-CTA and core-forming monomers, the solid content of the final products, the solution pH, the thermoresponsitivity of the macro-CTA, the macro-CTA end group, and the initiator concentration. Finally, several limitations and challenges for the PISA technique that have been recently addressed, along with those that will require further efforts into the future, will be highlighted.

Cargo Release from Polymeric Vesicles under Shear

In this paper we study the release of cargo from polymeric nano-carriers under shear. Vesicles formed by two star block polymers- A 12 B 6 C 2 ( A B C ) and A 12 B 6 A 2 ( A B A )-and one linear block copolymer- A 14 B 6 ( A B ), are investigated using dissipative particle dynamics (DPD) simulations. A - and C -blocks are solvophobic and B -block is solvophilic. The three polymers form vesicles of different structures. The vesicles are subjected to shear both in bulk and between solvophobic walls. In bulk shear, the mechanisms of cargo release are similar for all vesicles, with cargo travelling through vesicle membrane with no preferential release location. When sheared between walls, high cargo release rate is only observed with A B C vesicle after it touches the wall. For A B C vesicle, the critical condition for high cargo release rate is the formation of wall-polymersome interface after which the effect of shear rate in promoting cargo release is secondary. High release rate is achieved by the formation of solvophilic pathway allowing cargo to travel from the vesicle cavity to the vesicle exterior. The results in this paper show that well controlled target cargo release using polymersomes can be achieved with polymers of suitable design and can potentially be very useful for engineering applications. As an example, polymersomes can be used as carriers for surface active friction reducing additives which are only released at rubbing surfaces where the additives are needed most.

Toward Sulfur-Free RAFT Polymerization Induced Self-Assembly

Polymerization induced self-assembly (PISA) using methacrylate-based macromonomers as RAFT agents is an unexplored, attractive route to make self-assembled colloidal objects. The use of this class of RAFT-agents in heterogeneous polymerizations is however not trivial, because of their inherent low reactivity. In this work we demonstrate that two obstacles need to be overcome, one being control of chain-growth (propagation), the other monomer partitioning. Batch dispersion polymerizations of hydroxypropyl methacrylate in the presence of poly(glycerol methacrylate) macromonomers in water showed limited control of chain-growth. Semicontinuous experiments whereby monomer was fed improved results only to some extent. Control of propagation is essential for PISA to allow for dynamic rearrangement of colloidal structures. We tackled the problem of monomer partitioning (caused by uncontrolled particle nucleation) by starting the polymerization with an amphiphilic thermoresponsive diblock copolymer, already "phase-separated" from solution. TEM analysis showed that PISA was successful and that different particle morphologies were obtained throughout the polymerization.

Using Host-Guest Chemistry to Tune the Kinetics of Morphological Transitions Undertaken by Block Copolymer Vesicles

Host-guest chemistry is exploited to tune the rate at which block copolymer vesicles undergo morphological transitions. More specifically, a concentrated aqueous dispersion of poly(glycerol monomethacrylate-co-glycidyl methacrylate)-poly(2-hydroxypropyl methacrylate) [P(GMA-co-GlyMA)-PHPMA] diblock copolymer vesicles was prepared via polymerization-induced self-assembly (PISA). The epoxy groups in the GlyMA residues were ring-opened using a primary amine-functionalized β-cyclodextrin (NH₂-β-CD) in order to prepare β-CD-decorated vesicles. Addition of azobenzene-methoxypoly(ethylene glycol) (azo-mPEG) to such vesicles results in specific binding of this water-soluble macromolecular reagent to the β-CD groups on the hydrophilic P(GMA-co-GlyMA) stabilizer chains. Such host-guest chemistry induces a morphological transition from vesicles to worms and/or spheres. Furthermore, the rate of this morphological transition can be tuned by UV/visible-light irradiation and/or guest molecule competition. This novel molecular recognition strategy offers considerable scope for the design of new stimulus-responsive diblock copolymer vesicles for targeted delivery and controlled release of cargoes.