In Situ Study of Silicon Electrode Lithiation with X-ray Reflectivity

Probing Surface Dynamics of SiOx Thin-Film Electrodes during Cycling through X-Ray Photoemission Spectroscopy and Operando X-Ray Reflectivity

SiOx electrodes are promising for high-energy-density lithium-ion batteries (LIBs) due to their ability to mitigate volume expansion-induced degradation. Here, we investigate the surface dynamics of SiOx thin-film electrodes cycled in different carbonate-based electrolytes using a combination of ex situ X-ray photoelectron spectroscopy (XPS) and operando synchrotron X-ray reflectivity analyses. The thin-film geometry allows us to probe the depth-dependent chemical composition and electron density from surface to current collector through the solid electrolyte interphase (SEI), the active material, and the thickness evolution during cycling. Results reveal that SiOx lithiation initiates below 0.4 V vs Li+/Li and indicate a close relationship between SEI formation and SiOx electrode lithiation, likely due to the high resistivity of SiOx. We find similar chemical compositions for the SEI in FEC-containing and FEC-free electrolytes but observe a reduced thickness in the former case. In both cases, the SEI thickness decreases during delithiation due to the removal or dissolution of some carbonate species. These findings give insights into the (de)lithiation of SiOx, in particular, during the formation stage, and the effect of the presence of FEC in the electrolyte on the evolution of the SEI during cycling.

Design principle of disordered rocksalt type overlithiated anode for high energy density batteries

Rechargeable lithium-ion batteries with high energy density and fast-charging capability are vital for commercial applications. Disordered rocksalt (DRX) materials with a cation/anion ratio greater than one, achieved through additional lithium insertion, have emerged as promising high-rate anode candidates. Inspired by the previously reported Li3+xV2O5 (0 ≤ x ≤ 2) anode, a comprehensive search was conducted for all potential redox centers using high-throughput density functional theory (DFT) computations. This study examined 23 redox centers in a prototype formula Li3+xV2O5 (0 ≤ x ≤ 2) with the DRX structure, analyzing aspects such as voltage curve, theoretical capacity, energy density, phase stability, electronic conductivity, and volumetric change during cycling. Promising candidates were identified with redox centers including V, Cr, Nb, Mn, and Fe, marking them as potential anode materials. Additionally, this research revealed the origin of the low voltage in DRX anodes and proposed a method to optimize the average voltage by tuning the relative energies among structures with varying lithium contents. This work provides compositional design principles for the new promising DRX anode of LIBs with high energy density, fast-charging capability, and good cycling stability.

Operando Investigation of Silicon Anodes During Electrochemical Cycling in Li-ion Batteries

Silicon (Si) is recognized as a promising anode material for next-generation anodes due to its high capacity. However, large volume expansion and active particle pulverization during cycling rapidly deteriorate the battery performance. The relationship between Si anode particle size and particle pulverization, and the structure evolution of Si particles during cycling is not well understood. In this study, a quantitative, time-resolved "operando" small angle X-ray scattering (SAXS) investigation into the morphological change of unwrapped and reduced graphene oxide (rGO) wrapped Si nanoparticles (Si@rGO) is conducted with respect to the operating voltage. The results provide a clear picture of Si particle size change and the role of nonrigid rGO in mitigating Si volume expansion and pulverization. Further, this study demonstrates the advantage of "operando" SAXS in electrochemical environments as compared to other approaches.

Participation of electrochemically inserted protons in the hydrogen evolution reaction on tungsten oxides

Understanding the mechanisms by which electrodes undergo the hydrogen evolution reaction (HER) is necessary to design better materials for aqueous energy storage and conversion. Here, we investigate the HER mechanism on tungsten oxide electrodes, which are stable in acidic electrolytes and can undergo proton-insertion coupled electron transfer concomitant with the HER. Electrochemical characterization showed that anhydrous and hydrated tungsten oxides undergo changes in HER activity coincident with changes in proton composition, with activity in the order HxWO3·H2O > HxWO3 > HxWO3·2H2O. We used operando X-ray diffraction and density functional theory to understand the structural and electronic changes in the materials at high states of proton insertion, when the oxides are most active towards the HER. H0.69WO3·H2O and H0.65WO3 have similar proton composition, structural symmetry, and electronic properties at the onset of the HER, yet exhibit different activity. We hypothesize that the electrochemically inserted protons can diffuse in hydrogen bronzes and participate in the HER. This would render the oxide volume, and not just the surface, as a proton and electron reservoir at high overpotentials. HER activity is highest in HxWO3·H2O, which optimizes both the degree of proton insertion and solid-state proton transport kinetics. Our results highlight the interplay between the HER and proton insertion-coupled electron transfer on transition metal oxides, many of which are non-blocking electrodes towards protons.

In Situ and Operando X-ray Scattering Methods in Electrochemistry and Electrocatalysis

Electrochemical and electrocatalytic processes are of key importance for the transition to a sustainable energy supply as well as for a wide variety of other technologically relevant fields. Further development of these processes requires in-depth understanding of the atomic, nano, and micro scale structure of the materials and interfaces in electrochemical devices under reaction conditions. We here provide a comprehensive review of in situ and operando studies by X-ray scattering methods, which are powerful and highly versatile tools to provide such understanding. We discuss the application of X-ray scattering to a wide variety of electrochemical systems, ranging from metal and oxide single crystals to nanoparticles and even full devices. We show how structural data on bulk phases, electrode-electrolyte interfaces, and nanoscale morphology can be obtained and describe recent developments that provide highly local information and insight into the composition and electronic structure. These X-ray scattering studies yield insights into the structure in the double layer potential range as well as into the structural evolution during electrocatalytic processes and phase formation reactions, such as nucleation and growth during electrodeposition and dissolution, the formation of passive films, corrosion processes, and the electrochemical intercalation into battery materials.

Remote and automated high-throughput powder diffraction measurements enabled by a robotic sample changer at SSRL beamline 2-1

The general-purpose powder diffractometer beamline (BL2-1) at the Stanford Synchrotron Radiation Lightsource (SSRL) is described. The evolution of design and performance of BL2-1 are presented, in addition to current operating specifications, applications and measurement capabilities. Recent developments involve a robotic sample changer enabling high-throughput X-ray diffraction measurements, applicable to mail-in and remote operations. In situ and operando capabilities to measure samples with different form factors (e.g. capillary, flat plate or thin film, and transmission) and under variable experimental conditions are discussed. Several example datasets and accompanying Rietveld refinements are presented.

Toward Operando Characterization of Interphases in Batteries

Electrode/electrolyte interfaces are the most important and least understood components of Li-ion and next-generation batteries. An improved understanding of interphases in batteries will undoubtedly lead to breakthroughs in the field. Traditionally, evaluating those interphases involves using ex situ surface sensitive and/or imaging techniques. Due to their very dynamic and reactive nature, ex situ sample manipulation is undesirable. From this point of view, operando surface sensitive techniques represent a major opportunity to push boundaries in battery development. While numerous bulk spectroscopic, scattering, and imaging techniques are well established and widely used, surface sensitive operando techniques remain challenging and, to a larger extent, restricted to the model systems. Here, we give a perspective on techniques with the potential to characterize solid/liquid interfaces in both model and realistic battery configurations. The focus is on techniques that provide chemical and structural information at length and time scales relevant for the solid electrolyte interphase (SEI) formation and evolution, while also probing representative electrode areas. We highlight the following techniques: vibrational spectroscopy, X-ray photoelectron spectroscopy (XPS), neutron and X-ray reflectometry, and grazing incidence scattering techniques. Comprehensive overviews, as well as promises and challenges, of these techniques when used operando on battery interphases are discussed in detail.

Development of a versatile electrochemical cell for in situ grazing-incidence X-ray diffraction during non-aqueous electrochemical nitrogen reduction

In situ techniques are essential to understanding the behavior of electrocatalysts under operating conditions. When employed, in situ synchrotron grazing-incidence X-ray diffraction (GI-XRD) can provide time-resolved structural information of materials formed at the electrode surface. In situ cells, however, often require epoxy resins to secure electrodes, do not enable electrolyte flow, or exhibit limited chemical compatibility, hindering the study of non-aqueous electrochemical systems. Here, a versatile electrochemical cell for air-free in situ synchrotron GI-XRD during non-aqueous Li-mediated electrochemical N2 reduction (Li-N2R) has been designed. This cell not only fulfills the stringent material requirements necessary to study this system but is also readily extendable to other electrochemical systems. Under conditions relevant to non-aqueous Li-N2R, the formation of Li metal, LiOH and Li2O as well as a peak consistent with the α-phase of Li3N was observed, thus demonstrating the functionality of this cell toward developing a mechanistic understanding of complicated electrochemical systems.

Micro-Raman Stress Characterization of Crystalline Si as a Function of the Lithiation State

This work presents a stress characterization of crystalline Si electrodes using micro-Raman spectroscopy. First, the phase heterogeneity in the c-Si electrodes after initial lithiation was investigated by scanning electron microscopy (SEM) and other complementary techniques. A surprising three-phase layer structure, with a-Li_xSi (x = 2.5), c-Li_xSi (x = 0.3-2.5), and c-Si layers, was observed, and its origin was attributed to the electro-chemo-mechanical (ECM) coupling effect in the c-Si electrodes. Then, a Raman scan was performed to characterize stress distribution in lithiated c-Si electrodes. The results showed that the maximum tensile stress occurred at the interface between c-Li_xSi and c-Si layers, indicating a plastic flow behavior. The yield stress increased with total lithium charge, and the relationship showed consistency with a prior multibeam optical sensor (MOS) study. Lastly, stress distribution and structural integrity of the c-Si electrodes after initial delithiation and further cycling were studied, and a comprehensive picture of the failure mechanism of the c-Si electrode was obtained.

Recent Progress in Silicon-Based Materials for Performance-Enhanced Lithium-Ion Batteries

Silicon (Si) has been considered to be one of the most promising anode materials for high energy density lithium-ion batteries (LIBs) due to its high theoretical capacity, low discharge platform, abundant raw materials and environmental friendliness. However, the large volume changes, unstable solid electrolyte interphase (SEI) formation during cycling and intrinsic low conductivity of Si hinder its practical applications. Various modification strategies have been widely developed to enhance the lithium storage properties of Si-based anodes, including cycling stability and rate capabilities. In this review, recent modification methods to suppress structural collapse and electric conductivity are summarized in terms of structural design, oxide complexing and Si alloys, etc. Moreover, other performance enhancement factors, such as pre-lithiation, surface engineering and binders are briefly discussed. The mechanisms behind the performance enhancement of various Si-based composites characterized by in/ex situ techniques are also reviewed. Finally, we briefly highlight the existing challenges and future development prospects of Si-based anode materials.

Faster and lower-dose X-ray reflectivity measurements enabled by physics-informed modeling and artificial intelligence co-refinement

An approach is presented for analysis of real-time X-ray reflectivity (XRR) process data not just as a function of the magnitude of the reciprocal-space vector q, as is commonly done, but as a function of both q and time. The real-space structures extracted from the XRR curves are restricted to be solutions of a physics-informed growth model and use state-of-the-art convolutional neural networks (CNNs) and differential evolution fitting to co-refine multiple time-dependent XRR curves R(q, t) of a thin film growth experiment. Thereby it becomes possible to correctly analyze XRR data with a fidelity corresponding to standard fits of individual XRR curves, even if they are sparsely sampled, with a sevenfold reduction of XRR data points, or if the data are noisy due to a 200-fold reduction in counting times. The approach of using a CNN analysis and of including prior information through a kinetic model is not limited to growth studies but can be easily extended to other kinetic X-ray or neutron reflectivity data to enable faster measurements with less beam damage.

In Operando Neutron Scattering Multiple-Scale Studies of Lithium-Ion Batteries

Real-time observation of the electrochemical mechanistic behavior at various scales offers new insightful information to improve the performance of lithium-ion batteries (LIBs). As complementary to the X-ray-based techniques and electron microscopy-based methodologies, neutron scattering provides additional and unique advantages in materials research, owing to the different interactions with atomic nuclei. The non-Z-dependent elemental contrast, in addition to the high penetration ability and weak interaction with matters, makes neutron scattering an advanced probing tool for the in operando mechanistic studies of LIBs. The neutron-based techniques, such as neutron powder diffraction, small-angle neutron scattering, neutron reflectometry, and neutron imaging, have their distinct functionalities and characteristics regimes. These result in their scopes of application distributed in different battery components and covering the full spectrum of all aspects of LIBs. The review surveys the state-of-the-art developments of real-time investigation of the dynamic evolutions of electrochemically active compounds at various scales using neutron techniques. The atomic-scale, the mesoscopic-scale, and at the macroscopic-scale within LIBs during electrochemical functioning provide insightful information to battery researchers. The authors envision that this review will popularize the applications of neutron-based techniques in LIB studies and furnish important inspirations to battery researchers for the rational design of the new generation of LIBs.

High Power Energy Storage via Electrochemically Expanded and Hydrated Manganese-Rich Oxides

Understanding the materials design features that lead to high power electrochemical energy storage is important for applications from electric vehicles to smart grids. Electrochemical capacitors offer a highly attractive solution for these applications, with energy and power densities between those of batteries and dielectric capacitors. To date, the most common approach to increase the capacitance of electrochemical capacitor materials is to increase their surface area by nanostructuring. However, nanostructured materials have several drawbacks including lower volumetric capacitance. In this work, we present a scalable “top-down” strategy for the synthesis of EC electrode materials by electrochemically expanding micron-scale high temperature-derived layered sodium manganese-rich oxides. We hypothesize that the electrochemical expansion induces two changes to the oxide that result in a promising electrochemical capacitor material: (1) interlayer hydration, which improves the interlayer diffusion kinetics and buffers intercalation-induced structural changes, and (2) particle expansion, which significantly improves electrode integrity and volumetric capacitance. When compared with a commercially available activated carbon for electrochemical capacitors, the expanded materials have higher volumetric capacitance at charge/discharge timescales of up to 40 s. This shows that expanded and hydrated manganese-rich oxide powders are viable candidates for electrochemical capacitor electrodes.

Surface SiO2 Thickness Controls Uniform-to-Localized Transition in Lithiation of Silicon Anodes for Lithium-Ion Batteries

Silicon is a promising anode material for lithium-ion batteries because of its high capacity, but its widespread adoption has been hampered by a low cycle life arising from mechanical failure and the absence of a stable solid-electrolyte interphase (SEI). Understanding SEI formation and its impact on cycle life is made more complex by the oxidation of silicon materials in air or during synthesis, which leads to SiO_x coatings of varying thicknesses that form the true surface of the electrode. In this paper, the lithiation of SiO₂-coated Si is studied in a controlled manner using SiO₂ coatings of different thicknesses grown on Si wafers via thermal oxidation. SiO₂ thickness has a profound effect on lithiation: below 2 nm, SEI formation followed by uniform lithiation occurs at positive voltages versus Li/Li⁺. Si lithiation is reversible, and SiO₂ lithiation is largely irreversible. Above 2 nm SiO₂, voltammetric currents decrease exponentially with SiO₂ thickness. For 2-3 nm SiO₂, SEI formation above 0.1 V is suppressed, but a hold at low or negative voltages can initiate charge transfer whereupon SEI formation and uniform lithiation occur. Cycling of Si anodes with an SiO₂ coating thinner than 3 nm occurs at high Coulombic efficiency (CE). If an SiO₂ coating is thicker than 3-4 nm, the behavior is totally different: lithiation at positive voltages is strongly inhibited, and lithiation occurs at poor CE and is highly localized at pinholes which grow over time. As they grow, lithiation becomes more facile and the CE increases. Pinhole growth is proposed to occur via rapid transport of Li along the SiO₂/Si interface radially outward from an existing pinhole, followed by the lithiation of SiO₂ from the interface outward.

Nonpassivated Silicon Anode Surface

A stable solid electrolyte interphase (SEI) has been proven to be a key enabler to most advanced battery chemistries, where the reactivity between the electrolyte and the anode operating beyond the electrolyte stability limits must be kinetically suppressed by such SEIs. The graphite anode used in state-of-the-art Li-ion batteries presents the most representative SEI example. Because of similar operation potentials between graphite and silicon (Si), a similar passivation mechanism has been thought to apply on the Si anode when using the same carbonate-based electrolytes. In this work, we found that the chemical formation process of a proto-SEI on Si is closely entangled with incessant SEI decomposition, detachment, and reparation, which lead to continuous lithium consumption. Using a special galvanostatic protocol designed to observe the SEI formation prior to Si lithiation, we were able to deconvolute the electrochemical formation of such dynamic SEI from the morphology and mechanical complexities of Si and showed that a pristine Si anode could not be fully passivated in carbonate-based electrolytes.

Quantifying redox heterogeneity in single-crystalline LiCoO2 cathode particles

Active cathode particles are fundamental architectural units for the composite electrode of Li-ion batteries. The microstructure of the particles has a profound impact on their behavior and, consequently, on the cell-level electrochemical performance. LiCoO2 (LCO, a dominant cathode material) is often in the form of well-shaped particles, a few micrometres in size, with good crystallinity. In contrast to secondary particles (an agglomeration of many fine primary grains), which are the other common form of battery particles populated with structural and chemical defects, it is often anticipated that good particle crystallinity leads to superior mechanical robustness and suppressed charge heterogeneity. Yet, sub-particle level charge inhomogeneity in LCO particles has been widely reported in the literature, posing a frontier challenge in this field. Herein, this topic is revisited and it is demonstrated that X-ray absorption spectra on single-crystalline particles with highly anisotropic lattice structures are sensitive to the polarization configuration of the incident X-rays, causing some degree of ambiguity in analyzing the local spectroscopic fingerprint. To tackle this issue, a methodology is developed that extracts the white-line peak energy in the X-ray absorption near-edge structure spectra as a key data attribute for representing the local state of charge in the LCO crystal. This method demonstrates significantly improved accuracy and reveals the mesoscale chemical complexity in LCO particles with better fidelity. In addition to the implications on the importance of particle engineering for LCO cathodes, the method developed herein also has significant impact on spectro-microscopic studies of single-crystalline materials at synchrotron facilities, which is broadly applicable to a wide range of scientific disciplines well beyond battery research.

Nano-Architectured Composite Anode Enabling Long-Term Cycling Stability for High-Capacity Lithium-Ion Batteries

Failure mechanisms associated with silicon-based anodes are limiting the implementation of high-capacity lithium-ion batteries. Understanding the aging mechanism that deteriorates the anode performance and introducing novel-architectured composites offer new possibilities for improving the functionality of the electrodes. Here, the characterization of nano-architectured composite anode composed of active amorphous silicon domains (a-Si, 20 nm) and crystalline iron disilicide (c-FeSi₂ , 5-15 nm) alloyed particles dispersed in a graphite matrix is reported. This unique hierarchical architecture yields long-term mechanical, structural, and cycling stability. Using advanced electron microscopy techniques, the nanoscale morphology and chemical evolution of the active particles upon lithiation/delithiation are investigated. Due to the volumetric variations of Si during lithiation/delithiation, the morphology of the a-Si/c-FeSi₂ alloy evolves from a core-shell to a tree-branch type structure, wherein the continuous network of the active a-Si remains intact yielding capacity retention of 70% after 700 cycles. The root cause of electrode polarization, initial capacity fading, and electrode swelling is discussed and has profound implications for the development of stable lithium-ion batteries.

In Situ Neutron Reflectometry Study of Solid Electrolyte Interface (SEI) Formation on Tungsten Thin-Film Electrodes

Tungsten, a non-Li-intercalating material, was used as a platform to study solid-electrolyte interface/interphase (SEI) formation in lithium hexafluorphosphate in mixed diethyl carbonate (DEC)/ethylene carbonate electrolyte solutions using in situ neutron reflectometry (NR). A NR measurement determines the neutron scattering length density (SLD)-depth profile, from which a composition-depth profile can be inferred. Isotopic labeling/contrast variation measurements were conducted using a series of three electrolyte solutions: one with both solvents deuterated, one with neither deuterated, and another with only DEC deuterated. A two-layer SEI formed upon polarization to +0.25 V vs Li/Li⁺. Insensitivity of the inner SEI layer to solvent deuteration suggested limited incorporation of hydrogen atoms from the solvent molecules. Its low SLD indicates that Li₂O could be a major constituent. The outer SEI layer SLD scaled with that of the solution, indicating that it either had solution-filled porosity, incorporated hydrogen atoms from the solvent, or both. Returning the electrode to +2.65 V removed lithium from both surface layers, though the effect was more pronounced for the inner layer. Potential cycling had the effect of increasing the solution-derived species content in the inner SEI and decreased the contrast between the inner and outer layers, possibly indicating intermixing of the layers.

Multiscale Multiphase Lithiation and Delithiation Mechanisms in a Composite Electrode Unraveled by Simultaneous Operando Small-Angle and Wide-Angle X-Ray Scattering

The (de)lithiation process and resulting atomic and nanoscale morphological changes of an a-Si/c-FeSi₂/graphite composite negative electrode are investigated within a Li-ion full cell at several current rates (C-rates) and after prolonged cycling by simultaneous operando synchrotron wide-angle and small-angle X-ray scattering (WAXS and SAXS). WAXS allows the probing of the local crystalline structure. In particular, the observation of the graphite (de)lithiation process, revealed by the Li_xC₆ Bragg reflections, enables access to the respective capacities of both graphite and active silicon. Simultaneously and independently, information on the silicon state of (de)lithiation and nanoscale morphology (1 to 60 nm) is obtained through SAXS. During lithiation, the SAXS intensity in the region corresponding to characteristic distances within the a-Si/c-FeSi₂ domains increases. The combination of the SAXS/WAXS measurements over the course of several charge/discharge cycles, in pristine and aged electrodes, provides a complete picture of the C-rate-dependent sequential (de)lithiation mechanism of the a-Si/c-FeSi₂/graphite anode. Our results indicate that, within the composite electrode, the active silicon volume does not increase linearly with lithium insertion and point toward the important role of the electrode morphology to accommodate the nanoscale silicon expansion, an effect that remains beneficial after cell aging and most probably explains the excellent performance of the composite material.

Shedding X-ray Light on the Interfacial Electrochemistry of Silicon Anodes for Li-Ion Batteries

Electrochemical alloying reactions of group IV elements, such as Si, Ge, or Sn, with lithium provide a promising route to next-generation anode materials for lithium-ion batteries (LIBs) due to their high volumetric and gravimetric capacities. However, commercialization of these anodes is still sparse owing to quick capacity fading and limited Coulombic efficiency, which arise from large volume expansion leading to particle cracking and subsequent electrochemical inactivity. As a result, the solid electrolyte interphase (SEI), originating in the decomposition of the electrolyte upon battery operation outside the electrolyte's thermodynamic stability window, grows uncontrollably. While a large number of mitigation strategies have been developed, an improved nanometer level fundamental understanding of the (de)lithiation process and SEI formation, growth, and evolution is necessary to overcome these challenges. Toward this end, many experimental and theoretical approaches have been utilized but still provide an incomplete picture. This is due to the difficulty of investigating buried interfaces and interphases of lithiation products and thin SEI layers (nanometer-scale) in situ and with the desired nanometer accuracy. In this Account, we illustrate the utilization of in situ X-ray reflectivity (XRR) to provide nanometer-scale insights on the SEI nucleation, growth, and evolution, and well as the (de)lithiation process of Si electrodes. XRR is a nondestructive and surface- and interface-sensitive technique that allows for in situ investigations during battery operation under realistic electrochemical conditions. Insight into the system is provided via the surface-normal density profile, which is interpreted in terms of thickness, density, and roughness of individual surface layers, allowing monitoring of the interfacial morphology and chemistry evolution, through which the SEI growth and Si (de)lithiation process can be resolved. We utilized a model battery anode consisting of a native oxide terminated single crystalline Si wafer in half cell configuration with standard electrolyte in a specifically designed in situ XRR electrochemical cell. We have resolved the nucleation and formation process of the inner inorganic SEI and have observed two well-defined inorganic SEI layers on Si anodes: a bottom-SEI layer (adjacent to the electrode) formed via the lithiation of the native oxide and a top-SEI layer mainly consisting of the electrolyte decomposition product, LiF. This SEI layer grows during lithiation and contracts during delithiation. Further, our results show that the lithiation of crystalline Si (c-Si) is a layer-by-layer, reaction-limited, two-phase process with a well-defined phase boundary between Li_xSi lithiation product and c-Si; in contrast, the delithiation of Li_xSi and the lithiation of amorphous Si (a-Si) are reaction-limited, single-phase processes. Moreover, we resolved the influences of current density and the Si crystallographic orientation of the reaction interface on the (de)lithiation process. The implications of our findings are discussed with regard to battery performance.

Understanding the Role of Overpotentials in Lithium Ion Conversion Reactions: Visualizing the Interface

Oxide conversion reactions are known to have substantially higher specific capacities than intercalation materials used in Li-ion batteries, but universally suffer from large overpotentials associated with the formation of interfaces between the resulting nanoscale metal and Li₂O products. Here we use the interfacial sensitivity of operando X-ray reflectivity to visualize the structural evolution of ultrathin NiO electrodes and their interfaces during conversion. We observe two additional reactions prior to the well-known bulk, three-dimensional conversion occurring at 0.6 V: an accumulation of lithium at the buried metal/oxide interface (at 2.2 V) followed by interfacial lithiation of the buried NiO/Ni interface at the theoretical potential for conversion (at 1.9 V). To understand the mechanisms for bulk and interfacial lithiation, we calculate interfacial energies using density functional theory to build a potential-dependent nucleation model for conversion. These calculations show that the additional space charge layer of lithium is a crucial component for reducing energy barriers for conversion in NiO.

Intercalation of Layered Materials from Bulk to 2D

Intercalation in few-layer (2D) materials is a rapidly growing area of research to develop next-generation energy-storage and optoelectronic devices, including batteries, sensors, transistors, and electrically tunable displays. Identifying fundamental differences between intercalation in bulk and 2D materials will play a key role in developing functional devices. Herein, advances in few-layer intercalation are addressed in the historical context of bulk intercalation. First, synthesis methods and structural properties are discussed, emphasizing electrochemical techniques, the mechanism of intercalation, and the formation of a solid-electrolyte interphase. To address fundamental differences between bulk and 2D materials, scaling relationships describe how intercalation kinetics, structure, and electronic and optical properties depend on material thickness and lateral dimension. Here, diffusion rates, pseudocapacity, limits of staging, and electronic structure are compared for bulk and 2D materials. Next, the optoelectronic properties are summarized, focusing on charge transfer, conductivity, and electronic structure. For energy devices, opportunities also emerge to design van der Waals heterostructures with high capacities and excellent cycling performance. Initial studies of heterostructured electrodes are compared to state-of-the-art battery materials. Finally, challenges and opportunities are presented for 2D materials in energy and optoelectronic applications, along with promising research directions in synthesis and characterization to engineer 2D materials for superior devices.

Si nanoflake-assembled blocks towards high initial coulombic efficiency anodes for lithium-ion batteries

Assisted by artificial amorphous copper silicate, Si with a flake-like structure was obtained through a facile magnesiothermic reduction. The Si anodes exhibit excellent cyclic performance and rate performance. Particularly, a high initial coulombic efficiency of 85%-89% was obtained due to their greatly reduced surface and internal defects.

Lithium insertion into silicon electrodes studied by cyclic voltammetry and operando neutron reflectometry

Operando neutron reflectometry measurements were carried out to study the insertion of lithium into amorphous silicon film electrodes during cyclic voltammetry (CV) experiments at a scan rate of 0.01 mV s-1. The experiments allow mapping of regions where significant amounts of Li are incorporated/released from the electrode and correlation of the results to modifications of characteristic peaks in the CV curve. High volume changes up to 390% accompanied by corresponding modifications of the neutron scattering length density (which is a measure of the average Li fraction present in the electrode) are observed during electrochemical cycling for potentials below 0.3 V (lithiation) and above 0.2 V (delithiation), leading to a hysteretic behaviour. This is attributed to result from mechanical stress as suggested in the literature. Formation and modification of a surface layer associated with the solid electrolyte interphase (SEI) were observed during cycling. Within the first lithiation cycle the SEI grows to 120 Å for potentials below 0.5 V. Afterwards a reversible and stable modification of the SEI between 70 Å (delithiated state) and 120 Å (lithiated state) takes place.

Fluoroethylene Carbonate Induces Ordered Electrolyte Interface on Silicon and Sapphire Surfaces as Revealed by Sum Frequency Generation Vibrational Spectroscopy and X-ray Reflectivity

The cyclability of silicon anodes in lithium ion batteries (LIBs) is affected by the reduction of the electrolyte on the anode surface to produce a coating layer termed the solid electrolyte interphase (SEI). One of the key steps for a major improvement of LIBs is unraveling the SEI's structure-related diffusion properties as charge and discharge rates of LIBs are diffusion-limited. To this end, we have combined two surface sensitive techniques, sum frequency generation (SFG) vibrational spectroscopy, and X-ray reflectivity (XRR), to explore the first monolayer and to probe the first several layers of electrolyte, respectively, for solutions consisting of 1 M lithium perchlorate (LiClO₄) salt dissolved in ethylene carbonate (EC) or fluoroethylene carbonate (FEC) and their mixtures (EC/FEC 7:3 and 1:1 wt %) on silicon and sapphire surfaces. Our results suggest that the addition of FEC to EC solution causes the first monolayer to rearrange itself more perpendicular to the anode surface, while subsequent layers are less affected and tend to maintain their, on average, surface-parallel arrangements. This fundamental understanding of the near-surface orientation of the electrolyte molecules can aid operational strategies for designing high-performance LIBs.

Evidence of Tailoring the Interfacial Chemical Composition in Normal Structure Hybrid Organohalide Perovskites by a Self-Assembled Monolayer

Current-voltage hysteresis is a major issue for normal architecture organo-halide perovskite solar cells. In this manuscript we reveal a several-angstrom thick methylammonium iodide-rich interface between the perovskite and the metal oxide. Surface functionalization via self-assembled monolayers allowed us to control the composition of the interface monolayer from Pb poor to Pb rich, which, in parallel, suppresses hysteresis in perovskite solar cells. The bulk of the perovskite films is not affected by the interface engineering and remains highly crystalline in the surface-normal direction over the whole film thickness. The subnanometer structural modifications of the buried interface were revealed by X-ray reflectivity, which is most sensitive to monitor changes in the mass density of only several-angstrom thin interfacial layers as a function of substrate functionalization. From Kelvin probe force microscopy study on a solar cell cross section, we further demonstrate local variations of the potential on different electron-transporting layers within a solar cell. On the basis of these findings, we present a unifying model explaining hysteresis in perovskite solar cells, giving an insight into one crucial aspect of hysteresis for the first time and paving way for new strategies in the field of perovskite-based opto-electronic devices.

Operando Raman Spectroscopy and Synchrotron X-ray Diffraction of Lithiation/Delithiation in Silicon Nanoparticle Anodes

Operando Raman spectroscopy and synchrotron X-ray diffraction were combined to probe the evolution of strain in Li-ion battery anodes made of crystalline silicon nanoparticles. The internal structure of the nanoparticles during two discharge/charge cycles was evaluated by analyzing the intensity and position of Si diffraction peaks and Raman TO-LO phonons. Lithiation/delithiation of the silicon under limited capacity conditions triggers the formation of "crystalline core-amorphous shell" particles, which we evidenced as a stepwise decrease in core size, as well as sequences of compressive/tensile strain due to the stress applied by the shell. In particular, we showed that different sequences occur in the first and the second cycle, due to different lithiation processes. We further evidenced critical experimental conditions for accurate operando Raman spectroscopy measurements due to the different heat conductivity of lithiated and delithiated Si. Values of the stress extracted from both operando XRD and Raman are in excellent agreement. Long-term ex situ measurements confirmed the continuous increase of the internal compressive strain, unfavorable to the Si lithiation and contributing to the capacity fading. Finally, a simple mechanical model was used to estimate the sub-nanometer thickness of the interfacial shell applying the stress on the crystalline core. Our complete operando diagnosis of the strain and stress in SiNPs provides both a detailed scenario of the mechanical consequences of lithiation/delithiation in SiNP and also experimental values that are much needed for the benchmarking of theoretical models and for the further rational design of SiNP-based electrodes.

Determination of the Solid Electrolyte Interphase Structure Grown on a Silicon Electrode Using a Fluoroethylene Carbonate Additive

In this work we explore how an electrolyte additive (fluorinated ethylene carbonate – FEC) mediates the thickness and composition of the solid electrolyte interphase formed over a silicon anode in situ as a function of state-of-charge and cycle. We show the FEC condenses on the surface at open circuit voltage then is reduced to C-O containing polymeric species around 0.9 V (vs. Li/Li⁺). The resulting film is about 50 Å thick. Upon lithiation the SEI thickens to 70 Å and becomes more organic-like. With delithiation the SEI thins by 13 Å and becomes more inorganic in nature, consistent with the formation of LiF. This thickening/thinning is reversible with cycling and shows the SEI is a dynamic structure. We compare the SEI chemistry and thickness to 280 Å thick SEI layers produced without FEC and provide a mechanism for SEI formation using FEC additives.

Reversible Li-Ion Conversion Reaction for a TixGe Alloy in a Ti/Ge Multilayer

Group IV intermetallics electrochemically alloy with Li with stoichiometries as high as Li_4.4M (M = Si, Ge, Sn, or Pb). This provides the second highest known specific capacity (after pure lithium metal) for lithium-ion batteries, but the dramatic volume change during cycling greatly limits their use as anodes in Li-ion batteries. We describe an approach to overcome this limitation by constructing electrodes using a Ge/Ti multilayer architecture. In operando X-ray reflectivity and ex situ transmission electron microscopy are used to characterize the heterolayer structure at various lithium stoichiometries along a lithiation/delithiation cycle. The as-deposited multilayer spontaneously forms a one-dimensional Ti_xGe/Ti/Ti_xGe core-shell planar structure embedded in a Ge matrix. The interfacial Ti_xGe alloy is observed to be electrochemically active and exhibits reversible phase separation (i.e., a conversion reaction). Including the germanium components, the overall multilayer structure exhibits a 2.3-fold reversible vertical expansion and contraction and is shown to have improved capacity and capacity retention with respect to a Ge film with equivalent active material thickness.