2-Acrylamido-2-methyl-1-propanesulfonic Acid Grafted Poly(vinylidene fluoride-co-hexafluoropropylene)-Based Acid-/Oxidative-Resistant Cation Exchange for Membrane Electrolysis

Fabricating a Partially Fluorinated Hybrid Cation-Exchange Membrane for Long Durable Performance of Vanadium Redox Flow Batteries

The long-term durability of vanadium redox flow batteries (VRFBs) depends on the stability and performance of the membrane separator. We have architected a hybrid membrane by uniform dispersion of MIL-101(Cr) (Cr-MOF) in a partially fluorinated polymer grafted with sulfonic acid groups (PHP@AMPSCr-MOF(1.0)). The single cell VRFB performance of the PHP@AMPSCr-MOF(1.0) membrane was studied in comparison with the Cr-MOF incorporated Nafion membrane (NafionCr-MOF(1.0)) and showed an excellent result with 97.5% Coulombic efficiency (CE) at 150 mA/cm2 without any significant deterioration in the charge-discharge process for 1500 cycles (over 650 h). Meanwhile, the CE value of the NafionCr-MOF membrane (94.5%) deteriorated after 800 cycles (about 360 h) under similar conditions. The high VRFB performance of the PHP@AMPSCr-MOF(1.0) membrane has been attributed to the synergized properties and good interactions between Cr-MOF and partially fluorinated polymer matrix responsible for the creation of hydrophilic proton-conducting channels to achieve high selectivity. Furthermore, the cost-effective polymer and thus membranes may open new windows for practical applications in other energy devices such as fuel cells, electrolysis, and water treatment.

Highly Robust Laser-Induced Graphene (LIG) Ultrafiltration Membrane with a Stable Microporous Structure

Laser-induced graphene (LIG) materials have great potential in water treatment applications. Herein, we report the fabrication of a mechanically robust electroconductive LIG membrane with tailored separation properties for ultrafiltration (UF) applications. These LIG membranes are facilely fabricated by directly lasing poly(ether sulfone) (PES) membrane support. Control PES membranes were fabricated through a nonsolvent-induced phase separation (NIPS) technique. A major finding was that when PES UF membranes were treated with glycerol, the membrane porous structure remained almost unchanged upon drying, which also assisted with protecting the membrane's nanoscale features after lasing. Compared to the control PES membrane, the membrane fabricated with 8% laser power on the bottom layer of PES (PES (B)-LIG-HP) demonstrated 4 times higher flux (865 LMH) and 90.9% bovine serum albumin (BSA) rejection. Moreover, LIG membranes were found to be highly hydrophilic and exhibited excellent mechanical and chemical stability. Owing to their excellent permeance and separation efficiency, these highly robust electroconductive LIG membranes have a great potential to be used for designing functional membranes.

Synergistic Effect of 2-Acrylamido-2-methyl-1-propanesulfonic Acid on the Enhanced Conductivity for Fuel Cell at Low Temperature

This present work focused on the aromatic polymer (poly (1,4-phenylene ether-ether-sulfone); SPEES) interconnected/ cross-linked with the aliphatic monomer (2-acrylamido-2-methyl-1-propanesulfonic; AMPS) with the sulfonic group to enhance the conductivity and make it flexible with aliphatic chain of AMPS. Surprisingly, it produced higher conductivity than that of other reported work after the chemical stability was measured. It allows optimizing the synthesis of polymer electrolyte membranes with tailor-made combinations of conductivity and stability. Membrane structure is characterized by ¹H NMR and FT-IR. Weight loss of the membrane in Fenton's reagent is not too high during the oxidative stability test. The thermal stability of the membrane is characterized by TGA and its morphology by SEM and SAXS. The prepared membranes improved proton conductivity up to 0.125 Scm^-1 which is much higher than that of Nafion N115 which is 0.059 Scm^-1. Therefore, the SPEES-AM membranes are adequate for fuel cell at 50 °C with reduced relative humidity (RH).

High Ion-Exchange Capacity Semihomogeneous Cation Exchange Membranes Prepared via a Novel Polymerization and Sulfonation Approach in Porous Polypropylene

Semihomogeneous cation exchange membranes with superior ion exchange capacity (IEC) were synthesized via a novel polymerization and sulfonation approach in porous polypropylene support. The IEC of membranes could reach up to 3 mmol/g because of high mass ratio of functional polymer to membrane support. Especially, theoretical IEC threshold value agreed well with experimental threshold value, indicating that IEC could be specifically designed without carrying out extensive experiments. Also, sulfonate groups were distributed both on membrane surface and across the membranes, which corresponded well with high IEC of the synthesized membranes. In addition, the semifinished membrane showed hydrophobic property because of the formation of polystyrene. In contrast, the final membranes demonstrated super hydrophilic property, indicating the adequate sulfonation of polystyrene. Furthermore, when sulfonation reaction time increased, the conductivity of membranes also showed a tendency to increase, revealing the positive relationship between conductivity and IEC. Finally, the final membranes showed sufficient thermal stability for electrodialysis applications such as water desalination.

Toward improved mechanical strength, oxidative stability and proton conductivity of an aligned quadratic hybrid (SPEEK/FPAPB/Fe3O4-FGO) membrane for application in high temperature and low humidity fuel cells

Fe₃O₄ anchored functionalized GO is applied as a magnetically active filler as well as a solid proton conductor to realize an aligned hybrid membrane electrolyte architecture with blended polymer matrix consisting of FPAPB and SPEEK.

Ternary hybrid (SPEEK/SPVdF-HFP/GO) based membrane electrolyte for the applications of fuel cells: profile of improved mechanical strength, thermal stability and proton conductivity

Ternary hybrid membranes composed of sulfonated (poly ether ether ketone) (SPEEK), sulfonated polyvinylidene fluoride-co-hexafluoropropylene (SPVdF-HFP) and 1, 3, 5 or 7 wt% graphene oxide (GO) were fabricated using a facile solution casting method.