Green Preparation of Epoxy/Graphene Oxide Nanocomposites Using a Glycidylamine Epoxy Resin as the Surface Modifier and Phase Transfer Agent of Graphene Oxide

Biodegradable chitosan-graphene oxide as an affective green filler for improving of properties in epoxy nanocomposites

In this work, we investigated the effect of biodegradable Chitosan-encapsulated Graphene Oxide (CGO) on the morphology and properties of epoxy composites prepared using solution mixing with different filler loadings. The microstructures and properties of chitosan-GO and composites were studied using FTIR, XRD, SEM, TEM, tensile, impact, bending analysis, DMTA and TG tests. Microstructural observations confirmed that the CGO composition and its content in the matrix affected the distribution of fillers in the epoxy matrix. Mechanical and thermal tests indicated that the loading level of CGO and the ratio of chitosan to GO were the main factors that changed the strength of epoxy/CGOs composites. The tensile analysis confirmed that nanocomposites containing CGO exhibited a 65 % increase in elastic modulus due to the improved load transfer as a result of interfacial interactions between CGO and the matrix. DMTA analysis showed that the presence of CGO in the epoxy matrix increased T_g of the composite by ~30 °C. In the TGA test, although the introduction of CGO caused higher decomposition temperature of the CGO filled resins. CGO enhanced the final properties of epoxy-based nanocomposites as a result of the synergistic effect of chitosan and GO and the formation of 3-D CGO structures in the epoxy matrix.

Enhanced ultra violet resistance of epoxy nanocomposites filled with liquid-like graphene oxide/silicon dioxide nanofluid

The ultra violet (UV) resistance of epoxy resins has been paid more and more attention, and the development of highly efficient UV resistant materials is critical. Therefore, we showed liquid-like graphene oxide (GO)/silicon dioxide (SiO₂)-based derivatives for UV resistance of epoxy resins. To be specific, SiO₂ nanoparticles were deposited in situ on the surface of GO. Subsequently, a black, homogeneous and solvent-free GO/SiO₂ nanofluid was prepared by grafting organosilanes (KH560) and polyetheramines (M2070) on the surface of GO/SiO₂. Furthermore, the solvent-free GO/SiO₂ nanofluid/epoxy resin composites were also prepared. The bending properties before and after UV irradiation of the nanocomposites at room temperature were investigated to reveal the role of the interphase. The toughening mechanism of GO/SiO₂ nanofluid was elucidated by observing the fracture surface. As expected, the loss of bending strength of the resin resulting from UV illumination was efficiently reduced by the GO/SiO₂ nanofluid. This may be attributed to the excellent anti-UV aging properties of GO and SiO₂ nanoparticles. Moreover, the GO/SiO₂ nanofluid can provide excellent bending resistance for epoxy resin both before and after illumination, owing to its great compatibility with epoxy resin by organic chains and hindrance to crack propagation by nano cores.

Advances on Thermally Conductive Epoxy-Based Composites as Electronic Packaging Underfill Materials-A Review

The integrated circuits industry has been continuously producing microelectronic components with ever higher integration level, packaging density, and power density, which demand more stringent requirements for heat dissipation. Electronic packaging materials are used to pack these microelectronic components together, help to dissipate heat, redistribute stresses, and protect the whole system from the environment. They serve an important role in ensuring the performance and reliability of the electronic devices. Among various packaging materials, epoxy-based underfills are often employed in flip-chip packaging. However, widely used capillary underfill materials suffer from their low thermal conductivity, unable to meet the growing heat dissipation required of next-generation IC chips with much higher power density. Many strategies have been proposed to improve the thermal conductivity of epoxy, but its application as underfill materials with complex performance requirements is still difficult. In fact, optimizing the combined thermal-electrical-mechanical-processing properties of underfill materials for flip-chip packaging remains a great challenge. Herein, state-of-the-art advances that have been made to satisfy the key requirements of capillary underfill materials are reviewed. Based on these studies, the perspectives for designing high-performance underfill materials with novel microstructures in electronic packaging for high-power density electronic devices are provided.

Comparative Study of Different Methods of Synthesis and Their Effect on the Thermomechanical Properties of a Halogenated Epoxy-Based Flame-Retardant Resin

The work presented in this paper deals with the comparative synthesis of diglycidyl ether-based tetrabromobisphenol-A(TBBPA) using both conventional and nonconventional methods in order to explore materials for better industrial applications with respect to effective yield, cost, and time consideration. The conventional method involved the polycondensation of TBBPA and epichlorohydrin in the presence of an alkali catalyst. The nonconventional routes adopted for the synthesis of the material involved ultrasonication, microwave irradiation, and UV light exposure. The Fourier transform infrared spectroscopy spectra of all the synthesized materials of the resin were found to be identical, and the X-ray diffraction analysis showed the material as amorphous. The mechanical studies of the resins revealed that all these resins synthesized by different methods are strong and possess high viscosity. Based on the overall thermal, rheological, and excellent hydrophobic properties, it can serve as an excellent flame retardant.

Efficient and Recyclable Heterogeneous Catalyst Based on PdNPs Stabilized on a Green-Synthesized Graphene-like Nanomaterial: Effect of Surface Functionalization

This work reports for the first time a straightforward and efficient approach to covalent surface functionalization of a sustainable graphene-like nanomaterial with abundant carboxylic acid groups. This approach results in an efficient and robust chelatant platform for anchoring highly dispersed ultrasmall palladium particles with excellent catalytic activity in the reduction of both cationic (methylene blue, MB) and anionic (eosin-Y, Eo-Y) toxic organic dyes. The large-specific-surface-area (S_BET = 266.94 m²/g) graphene-like nanomaterial (GHN) was prepared through a green and cost-effective pyrolysis process from saccharose using layered bentonite clay as a template. To introduce a high density of carboxylic acid functions, GHN was first doubly functionalized by successive grafting reaction using two different strategies: (i) in the first case, GHN was first grafted by (3-glycidyloxypropyl) trimethoxysilane (GPTMS) and then bifunctionalized by chemical grafting of tris(4-hydroxyphenyl)methane triglycidyl ether (TGE). In the second case, the grafting order of the two molecules has been reversed. GHN-GPTMS-TGE provided the highest number of grafted reactive epoxy groups, and it was selected for further functionalization with carboxylic acid functions via a ring-opening reaction through a two-step hydrolysis (H₂SO₄)/oxidation (KMnO₄) approach. The GHN nanomaterial bearing carboxylic acid groups was then treated with sodium hydroxide to produce a deprotonated carboxylic acid-rich platform. Finally, due to a high density of accessible chelatant carboxylic acid groups, GHN-COO^- binds strongly a great amount of Pd²⁺ ions to form stable complexes which after reduction by NaBH₄ leads to highly dispersed, densely anchored, and uniformly distributed nanoscale Pd particles (d ∼ 4.5 nm) on the surface of the functionalized GHN. The GHN-COO^-@PdNPs nanohybrid proved to be highly efficient for dye reduction by NaBH₄ in aqueous solution at room temperature. Moreover, because of the high stability of the as-prepared graphene-like supported PdNPs, it exhibited very good reusability and could be recycled up to eight times without any significant loss in activity.

A transparent hydrophilic anti-biofouling coating for intraocular lens materials prepared by "bridging" of the intermediate adhesive layer

The attachment of bio-foulants, including unwanted cells, proteins, and bacteria, to a medical device such as an intraocular lens can lead to implantation failure. Hydrophilic polymers are often used as surface modifiers in the fabrication of anti-biofouling coatings, but a hydrophilic coating can easily become swollen and peel off the substrate. In this study, we chose polymethyl methacrylate (PMMA) as the representative material of intraocular lenses because PMMA has better biocompatibility, a higher refractive index, better optical clarity, lighter weight, more stable performance, and lower cost than other intraocular lens materials. We fabricated polyvinyl alcohol (PVA) coatings with or without a "bridge", that is, an intermediate adhesive layer (AL), to increase the adhesion bonding effect between the anti-biofouling coating and the substrate. The results indicated that the prepared coatings were transparent and noncytotoxic. Moreover, the anti-adhesion properties of the cells and the resistance properties to nonspecific protein adsorption of PMMA modified by both AL and PVA coatings were better and more durable compared with the sample only modified with a physically dipped PVA coating. The coating prepared by AL "bridging" provides a new strategy for the preparation of a transparent hydrophilic anti-biofouling coating suitable for PMMA intraocular lens materials.

Mechanical properties of aerospace epoxy composites reinforced with 2D nano-fillers: current status and road to industrialization

High-performance epoxy composites find application in the aerospace industry. Although epoxy is a high-performance polymer, its fracture toughness is compromised due to its highly cross-linked nature. Nanomaterials such as carbon nanotubes (CNTs), graphene derivatives, and inorganic 2-dimensional (2D) nanomaterials are being explored to improve epoxy composites' mechanical properties. Graphene is one of the most popular 2D nano-reinforcing agents for epoxy composites. Following graphene discovery, the research community's attention was brought to various other few-atom thick 2D nanomaterials. Hence, apart from graphene, inorganic nanosheets such as transition metal dichalcogenides (TMDs), hexagonal boron nitride (hBN), etc., are also being studied as modifiers for enhancing the mechanical performance of epoxy composites. Graphene, TMDs and hBN are known to possess a high aspect ratio, high specific surface area and inherently high mechanical strength and stiffness, contributing to a stronger and tougher composite. Despite that, the challenges associated with these nanomaterials, such as dispersion issues, lack of standardization, underlying health hazards, etc., have hampered their commercialization. It has been long past a decade since the discovery of graphene, yet there are concerns regarding the lab to industry scale-up, and health and environmental hazards associated with nanomaterials for the fabrication of aerospace composites. This review offers a comprehensive literature survey and a perspective into the possible ways of bridging the gaps between the laboratory research and industrialization of 2D nanosheet-filled epoxy composites.

The correlated effects of polyetheramine-functionalized graphene oxide loading on the curing reaction and the mechanical properties of epoxy composites

In this study, the effects of polyetheramine (D230) functionalized graphene oxide loading on the curing reaction, thermal and mechanical properties of epoxy composites were studied and the correlation between structure and property of epoxy composite was established. In the functionalization of graphene oxide (GO), the effect of the mass ratio of D230 to GO on chemical properties of the functionalized GO was investigated. Results showed that D230 were successfully covalently grafted onto surface of two-dimensional functionalized GO sheet. The functionalized GO sheets prepared under optimal condition of D230/GO ratio of 1:1 dispersed evenly in epoxy composites, indicating the possibility of the epoxy composite fabrication by the solvent-free technique. The analysis of qualitative Cure Index suggested that epoxy composites were subjected to excellent curing. The quantitative evaluation of curing kinetics demonstrated that the functionalized GO exhibited a chemical facilitation on the curing reaction. However, the functionalized GO simultaneously physically restricted the curing reactivity, especially at high loading. These contributed to the improved interfacial properties and high toughness of the epoxy composites. Compared to neat epoxy, the epoxy composites showed effective tensile strength improvement of ∼10.0% (77.0 MPa), tensile modulus enhancement of ∼7.7% (3.34 GPa), flexural modulus increment of ∼12.1% (3.43 GPa), and flexural strength increment of ∼10.6% (124.3 MPa). This study demonstrated an effective and environment-friendly strategy to design GO reinforced epoxy composites with favorable dispersion and interfacial bonding, and it further clarified the relationship between the crosslinking network/interfacial structure and the mechanical properties of epoxy composites.

Chemically activated core–shell structured IF-WS2@C nanoparticles enhance sugarcane-based carbon/epoxy nanocomposites

Ternary composites have demonstrated better capability than binary composites in enhancing the mechanical properties of the modified epoxy resins and are, therefore, currently under intensive investigation. Herein, we report a novel ternary nanocomposite prepared by filling a binary BPF (bisphenol F epoxy resin)/SCPs (sugarcane-based carbon powders) matrix with C-coated inorganic fullerene-like tungsten disulfide (IF-WS₂@C) nanoparticles, and the analysis of its interface synergetic effect using XPS/FTIR. This activated nano-carbon core–shell structure filler is considered an ideal nanofiller and shows the excellent mechanical performance of the ternary composites. XRD, IR, XPS, SEM, and TEM characterizations were applied in investigating this nanocomposite. The improvement of the thermal and mechanical properties demonstrated the enhancement effects of this nanofiller. The results show that the great improvement of the bending modulus of 39.4% increased with the addition of 0.5 wt% IF-WS₂@C nanoparticles, while 34.1% enhancement of bending strength was obtained with the addition of 0.2 wt% IF-WS₂@C nanoparticles. The hardness and thermal conductivity were also boosted up to 5.2% and 33.1% with 0.5 wt% addition, respectively. The incorporation of a chemically activated coating may provide a novel means for improving graphite crystallization, which could somehow expand the potential application of IF-WS₂@C nanoparticles.

Schematic diagram and typical curing mechanism of epoxy resins and the unique interactions of the IF-WS₂@C nanoparticles introduced into the matrix.

Enhancing the mechanical and tribological properties of epoxy composites via incorporation of reactive bio-based epoxy functionalized graphene oxide

The high rigidity and brittleness of traditional thermosetting resin based on bisphenol epoxy limits its many potential technical applications. Here, a novel tertiary amine containing cardanol-based epoxy resin (NC-514-DEA) was synthesized by reaction of diethanolamine (DEA) with cardanol epoxy resin (NC-514). Moreover, NC-514-DEA modified graphene oxide (GOND) was prepared and used as a reactive nano-reinforcing filler for epoxy composites. The results show that, compared with neat epoxy resin, the fracture toughness of the epoxy composite with 0.5 wt% GOND is increased by nearly 10%, and the friction coefficient is reduced from 0.567 to 0.408, demonstrating the best performance among specimens. The improved mechanical and wear resistance properties of prepared composites were attribute to the synergistic effect of NC-514-DEA and GO, which inhibited the generation and propagation of cracks by enhancing the interfacial interaction and distributing stress. In addition, the synthetic process of GOND is green, simple and efficient, providing a novel way for designing epoxy composite materials with many potential applications.

Enhancement of Thermal and Mechanical Properties of Bismaleimide Using a Graphene Oxide Modified by Epoxy Silane

A thermosetting resin system, based on bismaleimide (BMI), has been developed via copolymerization of 4,4′-diaminodiphenylsulfone with a newly synthesized graphene oxide modified using epoxy silane (ES-GO). The effect of ES-GO on the thermomechanical and mechanical properties of cured modified resin was studied. To evaluate the efficiency of the modified BMI systems, the composite samples using glass fiber cloth were molded and tested. Thermogravimetric analysis indicates that the cured sample systems displays a high char yield at lower concentrations of ES-GO (≤0.5 wt.%), suggesting an improved thermal stability. Using dynamic mechanical analysis, a marked increase in glass transition temperature (Tg) with increasing ES-GO content was observed. Analysis of mechanical properties reveals a possible effect of ES-GO as a toughener. The results also showed that the addition of 0.3 wt.% ES-GO maximizes the toughness of the modified resin systems, which was further confirmed by the result of analysis of fracture surfaces. At the same time, a molded composite with ES-GO showed improved mechanical properties and retention rate at 150 °C as compared to that made with neat resin.

Superior to graphene: super-anticorrosive natural mica nanosheets

Graphene has been generally considered to be the most ideal anticorrosive material based on its extraordinary impermeability, but tends in practical applications to promote metal corrosion because of its inherently high electrical conductivity. Mica nanosheets (MNSs), in contrast, display excellent electrical insulation properties, as well as excellent temperature stability and chemical durability, and show tremendous potential for protecting metals, and hence are a promising substitute for graphene. To date, however, there have been no reports about MNS-based anticorrosive coatings, since it is much more difficult to exfoliate high-quality MNSs than other layered materials. In this work, high-concentration (4.3 mg ml-1) ultrathin MNS (1-5 layers) dispersions were synthesized based on a facile and efficient hydrothermal exfoliation approach. Epoxy (EP) coatings were filled with the as-obtained MNSs to enhance the anticorrosion performance of the coatings, and their corrosion behaviors were studied systemically through a series of measurements. With the addition of only 0.4 wt% MNSs, the corrosion rate was observed to be reduced 6500 fold, and the coating impedance increased by four orders of magnitude compared with the blank EP coating. We believe that this method opens a novel avenue for developing high-performance anticorrosive coatings to replace graphene materials for metal protection.

Tailoring graphene reinforced thermoset and biothermoset composites

The surge of knowledge among researchers pertaining to the excellent properties of graphene has led to the utilisation of graphene as a reinforced filler in polymer composites. Different methods of graphene preparation, either bottom-up or top-down methods, are important requirements of starting materials in producing reinforced properties in the composites. The starting graphene material produced is either further functionalised or directly used as a filler in thermoset polymer matrixes. An effective interaction between graphene and polymer matrixes is important and can be achieved by incorporating graphene into a thermoset polymer matrix through melt mixing, solution mixing or in situ polymerisation processes. In addition, by taking into consideration the importance of green and sustainable composites, the details of previous work on graphene reinforced bio-thermoset polymer matrixes is discussed. The resultant mechanical and thermal properties of the composites were associated to the chemical interaction between the graphene filler and a thermoset matrix. Exploration for further variations of graphene polymer composites are discussed by taking the reinforcement properties in graphene composite as a starting point.

Thin Nacre-Biomimetic Coating with Super-Anticorrosion Performance

The rigorous organic and inorganic laminated structure of nacre has been developed by millions of years of biological evolution against various external impacts, including mechanical loadings and chemical attacks. Nacre-biomimetic materials have been recognized as an effective strategy to achieve high strength and toughness simultaneously. However, the understanding of nacre-like structure from the perspective of corrosion protection is still very limited. This work investigates the anticorrosion performance of nacre-biomimetic GO/epoxy (NBGE) coatings with alternating layers. Potentiodynamic polarization measurements indicated that the corrosion rate of steel protected by the NBGE coating with 5 layers of GO and 6 layers of epoxy (5NBGE) and a total thickness of 17 μm was 20 times slower than that of steel under the pure epoxy coating twice as thick in 3.5 wt % NaCl solution. Electrochemical impedance spectroscopy measurements revealed the importance and functions of the GO layers in NBGE coatings. The 5NBGE coating exhibited better performance than carbon-based nanoparticle/epoxy mixed coatings. The superior anticorrosion performance of the NB5G6E coating was supported by photographic observations, scanning electron microscopy, energy-dispersive X-ray spectroscopy, and chloride diffusion measurements. The strong cross-linking layer-by-layer structure of NBGE coatings was proved by Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and X-ray diffraction analyses. The anticorrosion mechanism of the NBGE coatings was interpreted by the mitigation of chemical reactions occurring at the steel-coating interface due to the restricted intrusion of O₂, H₂O, and Cl^- through the reduced pores and defects by the intercalated GO layers in the coatings.

Simultaneously 'pushing' and 'pulling' graphene oxide into low-polar solvents through a designed interface

Dispersing graphene oxide (GO) in low-polar solvents can realize a perfect self-assembly with functional molecules and application in removal of organic impurities that only dissolve in low-polar solvents. The surface chemistry of GO plays an important role in its dispersity in these solvents. The direct transfer of hydrophilic GO into low-polar solvents, however, has remained an experimental challenge. In this study, we design an interface to transfer GO by simultaneously 'pushing and pulling' the nanosheets into low-polar solvents. Our approach is outstanding due to the ability to obtain monolayers of chemically reduced GO (CRGO) with designed surface properties in the organic phase. Using the transferred GO or CRGO dispersions, we have fabricated GO/fullerene nanocomposites and assessed the ability of CRGOs for dye adsorption. We hope our work can provide a universal approach for the phase transfer of other nanomaterials.

Evaluation of the Photothermal Properties of a Reduced Graphene Oxide/Arginine Nanostructure for Near-Infrared Absorption

Strong near-infrared (NIR) absorption of reduced graphene oxide (rGO) make this material a candidate for photothermal therapy. The use of rGO has been limited by low stability in aqueous media due to the lack of surface hydrophilic groups. We report synthesis of a novel form of reduced graphene-arginine (rGO-Arg) as a nanoprobe. Introduction of Arg to the surface of rGO not only increases the stability in aqueous solutions but also increases cancer cell uptake. Atomic force microscopy (AFM) and transmission electron microscopy (TEM) images are recorded to characterize the morphology of rGO-Arg. Fourier transform infrared (FTIR), X-ray photoelectron spectra (XPS), Raman, and UV-vis spectroscopy are utilized to analyze the physiochemical properties of rGO-Arg. Interaction of rGO-Arg with 808 nm laser light has been evaluated by measuring the absorption cross section in response to periodically modulated intensity to minimize artifacts arising from lateral thermal diffusion with a material scattering matched to a low scattering optical standard. Cell toxicity and cellular uptake by MD-MB-231 cell lines provide supporting data for the potential application of rGO-Arg for photothermal therapy. Absorption cross-section results suggest rGO-Arg is an excellent NIR absorber that is 3.2 times stronger in comparison to GO.

Photothermal Conversion Triggered Precisely Targeted Healing of Epoxy Resin Based on Thermoreversible Diels-Alder Network and Amino-Functionalized Carbon Nanotubes

In the present work, we demonstrated the recyclability and precisely targeted reparability of amino functionalized multiwall carbon nanotubes-epoxy resin based on dynamic covalent Diels-Alder (DA) network (NH₂-MWCNTs/DA-epoxy) by exploring the photothermal conversion of CNTs to trigger the reactions of dynamic chemical bonds. The covalent cross-linked networks of NH₂-MWCNTs/DA-epoxy resin change their topology to linear polymer by thermally activated reverse Diels-Alder (r-DA) reactions at high temperatures, which endues the resin with almost 100% recyclability. The self-healing property of the epoxy resin was confirmed by the complete elimination of cracks after the reconstruction of DA network induced by heating or near-infrared (NIR) irradiation. For heat-triggered self-healing process, heat energy may also act on those uninjured parts of the resin and cause the dissociation of the whole DA network. Therefore, redundant r-DA and DA reactions, which have no contribution to self-healing, are also triggered during thermal treatment, resulting in not only a waste of energy but also the deformation of the sample under external force. Meanwhile, for the NIR-triggered self-healing process, the samples can maintain well their original shape without observable deformation after irradiation. The NIR-triggered healing process, which uses MWCNTs as the photothermal convertor, have very good regional controllability by simply tuning the MWCNTs content, the distance from NIR laser source to sample, and the laser power. The injured samples can be locally repaired with high precision and efficiency without an obvious influence on those uninjured parts.

Sustainability of renewable fuel infrastructure: a screening LCA case study of anticorrosive graphene oxide epoxy liners in steel tanks for the storage of biodiesel and its blends

Biodiesel is a widely used fuel that meets the renewable fuel standards developed under the Energy Policy Act of 2005. However, biodiesel is known to pose a series of abiotic and biotic corrosion risks to storage tanks. A typical practice (incumbent system) used to protect the tanks from these risks include (i) coating the interior surface of the tank with a solvent-free epoxy (SFE) liner, and (ii) adding a biocide to the tank. Herein, we present a screening-level life-cycle assessment study to compare the environmental performance of a graphene oxide (GO)-epoxy (GOE) liner with the incumbent system. TRACI was used as an impact assessment tool to model the midpoint environmental impacts in ten categories: global warming potential (GWP, kg CO₂ eq.); acidification potential (AP, kg SO₂ eq.); potential human health damage impacts due to carcinogens (HH-CP, CTU_h) and non-carcinogens (HH-NCP, CTU_h); potential respiratory effects (REP, kg PM_2.5 eq.); eutrophication potential (EP, kg N eq.); ozone depletion potential (ODP kg CFC-11 eq.); ecotoxicity potential (ETXP, CTU_e); smog formation potential (SFP kg O₃ eq.) and fossil fuel depletion potential (FFDP MJ surplus). The equivalent functional unit of the LCA study was designed to protect 30 m² of the interior surface (unalloyed steel sheet) of a 10 000 liter biodiesel tank against abiotic and biotic corrosion during its service life of 20 years. Overall, this LCA study highlights the improved environmental performance for the GOE liner compared to the incumbent system, whereby the GOE liner showed 91% lower impacts in ODP impact category, 59% smaller in REP, 62% smaller in AP, 67-69% smaller in GWP and HH-CP, 72-76% smaller in EP, SFP, and FFDP, and 81-83% smaller ETXP and HH-NCP category results. The scenario analysis study revealed that these potential impacts change by less than 15% when the GOE liners are functionalized with silanized-GO nanosheets or GO-reinforced polyvinyl carbazole to improve the antimicrobial properties. The results from an uncertainty analysis indicated that the impacts for the incumbent system were more sensitive to changes in the key modeling parameters compared to that for the GOE liner system.

Facile and green preparation of biobased graphene oxide/furan resin nanocomposites with enhanced thermal and mechanical properties

A facile and green approach was developed to prepare biobased graphene oxide (GO)/furan resin nanocomposites by directly transferring GO from water dispersion into furan resin.