A Flexible and Thin Graphene/Silver Nanowires/Polymer Hybrid Transparent Electrode for Optoelectronic Devices

Tough Monolayer Silver Nanowire-Reinforced Double-Layer Graphene

Mixed-dimensional nanomaterials composed of one-dimensional (1D) and two-dimensional (2D) nanomaterials, such as graphene-silver nanowire (AgNW) composite sandwiched structures, are promising candidates as building blocks for multifunctional structures and materials. However, their mechanical behavior and failure mechanism have not yet been fully understood. In this work, we have performed integrated experimental, theoretical, and numerical studies to explore the performance and failure modes of graphene-AgNW composite under tensile and impact loading conditions. In situ tensile tests using a nanoindenter, implemented with a push-to-pull device and a laser-induced projectile impact test system, are used to shed light on load-bearing mechanisms in graphene-AgNW composites. Multiple failure modes have been observed in both experimental setups and analyzed with numerical and theoretical models. Results show that in the tensile loading the distribution of AgNW, as characterized by the effective free length, is the key parameter determining the failure mode. As for the impact failure scenarios, compared with failure modes observed in pure graphene cases, the mechanical reinforcing effect of AgNW will transform the failure mode from a scattered tensile fracture along radial directions to a shear failure that is constrained in a relatively local domain. Theoretical analysis using shear lag modeling, Timoshenko plate theory, molecular dynamics modeling, and finite element modeling approaches are adopted to further establish the failure modes.

Metal nanowire-based transparent electrode for flexible and stretchable optoelectronic devices

High-quality transparent electrodes are indispensable components of flexible optoelectronic devices as they guarantee sufficient light transparency and electrical conductivity. Compared to commercial indium tin oxide, metal nanowires are considered ideal candidates as flexible transparent electrodes (FTEs) owing to their superior optoelectronic properties, excellent mechanical flexibility, solution treatability, and higher compatibility with semiconductors. However, certain key challenges associated with material preparation and device fabrication remain for the practical application of metal nanowire-based electrodes. In this review, we discuss state-of-the-art solution-processed metal nanowire-based FTEs and their applications in flexible and stretchable optoelectronic devices. Specifically, the important properties of FTEs and a cost-benefit analysis of existing technologies are introduced, followed by a summary of the synthesis strategy, key properties, and fabrication technologies of the nanowires. Subsequently, we explore the applications of metal-nanowire-based FTEs in different optoelectronic devices including solar cells, photodetectors, and light-emitting diodes. Finally, the current status, future challenges, and emerging strategies in this field are presented.

Highly Stable Silver Nanowire Plasmonic Electrodes for Flexible Polymer Light-Emitting Devices

Silver nanowire (AgNW) transparent electrodes are considered as a promising candidate for applications in flexible optoelectronic devices. However, it remains a great challenge to obtain flexible AgNW electrodes with excellent optoelectrical properties and mechanical flexibility. Here, highly stable Ag nanoparticle (AgNP)-enhanced plasmonic AgNW electrodes are demonstrated via the controllable in situ growth of AgNPs at the AgNW junctions and introduction of an l-histidine (l-His) wrapping layer. The flexible transparent electrodes of AgNW-AgNP/l-His possess a low sheet resistance (Rsh) of ∼17.5 Ω sq-1, a high transmittance of ∼92.5% (550 nm), and a robust mechanical stability (100,000 bending cycles). Benefiting from plasmon-coupling effects, flexible polymer light-emitting devices (FPLEDs) with AgNW-AgNP/l-His electrodes present a current efficiency (CE) of ∼14.8 cd A-1 and an external quantum efficiency (EQE) of ∼5.6%, constituting ∼80% and ∼75% increases compared to those of the reference devices with AgNW electrodes, respectively. Additionally, the laminated flexible transparent PLEDs (FT-PLEDs) are demonstrated by integrating polydimethylsiloxane/AgNW-AgNP anodes by a soft lamination process. The FT-PLEDs present a CE of ∼7.1 cd A-1 (cathode side: ∼3.9 cd A-1; anode side: ∼3.2 cd A-1) and an EQE of ∼2.7% (cathode side: ∼1.5%; anode side: ∼1.2%). Furthermore, the FPLEDs and FT-PLEDs exhibit robust mechanical durability, maintaining ∼89% and ∼86% of their initial luminance after 1000 bending cycles at a bending radius of 2 mm, respectively. This work opens up a new avenue for the development of high performance and stable flexible optoelectronic devices.

Mechanical Durability and Flexibility in Perovskite Photovoltaics: Advancements and Applications

The remarkable progress in perovskite solar cell (PSC) technology has witnessed a remarkable leap in efficiency within the past decade. As this technology continues to mature, flexible PSCs (F-PSCs) are emerging as pivotal components for a wide array of applications, spanning from powering portable electronics and wearable devices to integrating seamlessly into electronic textiles and large-scale industrial roofing. F-PSCs characterized by their lightweight, mechanical flexibility, and adaptability for cost-effective roll-to-roll manufacturing, hold immense commercial potential. However, the persistent concerns regarding the overall stability and mechanical robustness of these devices loom large. This comprehensive review delves into recent strides made in enhancing the mechanical stability of F-PSCs. It covers a spectrum of crucial aspects, encompassing perovskite material optimization, precise crystal grain regulation, film quality enhancement, strategic interface engineering, innovational developed flexible transparent electrodes, judicious substrate selection, and the integration of various functional layers. By collating and analyzing these dedicated research endeavors, this review illuminates the current landscape of progress in addressing the challenges surrounding mechanical stability. Furthermore, it provides valuable insights into the persistent obstacles and bottlenecks that demand attention and innovative solutions in the field of F-PSCs.

Flexible Transparent Conductive Electrodes: Unveiling Growth Mechanisms, Material Dimensions, Fabrication Methods, and Design Strategies

Flexible transparent conductive electrodes (FTCEs) constitute an indispensable component in state-of-the-art electronic devices, such as wearable flexible sensors, flexible displays, artificial skin, and biomedical devices, etc. This review paper offers a comprehensive overview of the fabrication techniques, growth modes, material dimensions, design, and their impacts on FTCEs fabrication. The growth modes, such as the "Stranski-Krastanov growth," "Frank-van der Merwe growth," and "Volmer-Weber growth" modes provide flexibility in fabricating FTCEs. Application of different materials including 0D, 1D, 2D, polymer composites, conductive oxides, and hybrid materials in FTCE fabrication, emphasizing their suitability in flexible devices are discussed. This review also delves into the design strategies of FTCEs, including microgrids, nanotroughs, nanomesh, nanowires network, and "kirigami"-inspired patterns, etc. The pros and cons associated with these materials and designs are also addressed appropriately. Considerations such as trade-offs between electrical conductivity and optical transparency or "figure of merit (FoM)," "strain engineering," "work function," and "haze" are also discussed briefly. Finally, this review outlines the challenges and opportunities in the current and future development of FTCEs for flexible electronics, including the improved trade-offs between optoelectronic parameters, novel materials development, mechanical stability, reproducibility, scalability, and durability enhancement, safety, biocompatibility, etc.

Flexible Nanocomposite Conductors for Electromagnetic Interference Shielding

HIGHLIGHTS

Convincing candidates of flexible (stretchable/compressible) electromagnetic interference shielding nanocomposites are discussed in detail from the views of fabrication, mechanical elasticity and shielding performance. Detailed summary of the relationship between deformation of materials and electromagnetic shielding performance. The future directions and challenges in developing flexible (particularly elastic) shielding nanocomposites are highlighted. With the extensive use of electronic communication technology in integrated circuit systems and wearable devices, electromagnetic interference (EMI) has increased dramatically. The shortcomings of conventional rigid EMI shielding materials include high brittleness, poor comfort, and unsuitability for conforming and deformable applications. Hitherto, flexible (particularly elastic) nanocomposites have attracted enormous interest due to their excellent deformability. However, the current flexible shielding nanocomposites present low mechanical stability and resilience, relatively poor EMI shielding performance, and limited multifunctionality. Herein, the advances in low-dimensional EMI shielding nanomaterials-based elastomers are outlined and a selection of the most remarkable examples is discussed. And the corresponding modification strategies and deformability performance are summarized. Finally, expectations for this quickly increasing sector are discussed, as well as future challenges.

Solution-Processed Flexible Transparent Electrodes for Printable Electronics

Flexible transparent electrodes (FTEs) have been widely witnessed in various printable electronic devices, especially those involving light. So far, solution processes have demonstrated increasing advantages in preparing FTEs not only in their mild operation conditions and high-throughput but also in the diversity in micropatterning conductive nanomaterials into networks. For the FTEs, both high transparency and high conductivity are desirable, which therefore create requirements for the conductive network by considering the trade-off relationship between the coverage and the micropatterns of the network. In addition, the conductive networks also affect the flexibility of FTEs due to the deformation during bending/stretching. Consequently, solution processes capable of micropatterning conductive nanomaterials including nanoparticles, nanowires/polymers, and graphene/MXene play a crucial role in determining the performance of FTEs. Here, we reviewed recent research progress on solution-processed FTEs, including the solution processes, the solution-processable conductive nanomaterials and the substrates for making FTEs, and applications of FTEs in flexible electronics. Finally, we proposed several perspective outlooks of the FTEs, which aim at not only the enhanced performance but also the performances in extreme conditions and in integration. We believe that the review would offer inspiration for developing functional FTEs.

Transparent Conducting Films Based on Carbon Nanotubes: Rational Design toward the Theoretical Limit

Electrically conductive thin-film materials possessing high transparency are essential components for many optoelectronic devices. The advancement in the transparent conductor applications requires a replacement of indium tin oxide (ITO), one of the key materials in electronics. ITO and other transparent conductive metal oxides have several drawbacks, including poor flexibility, high refractive index and haze, limited chemical stability, and depleted raw material supply. Single-walled carbon nanotubes (SWCNTs) are a promising alternative for transparent conducting films (TCFs) because of their unique and excellent chemical and physical properties. Here, the latest achievements in the optoelectronic performance of TCFs based on SWCNTs are analyzed. Various approaches to evaluate the performance of transparent electrodes are briefly reviewed. A roadmap for further research and development of the transparent conductors using "rational design," which breaks the deadlock for obtaining the TCFs with a performance close to the theoretical limit, is also described.

Mixed-Dimensional MXene-Based Composite Electrodes Enable Mechanically Stable and Efficient Flexible Perovskite Light-Emitting Diodes

Significant advancements in perovskite light-emitting diodes (PeLEDs) based on ITO glass substrates have been realized in recent years, yet the overall performance of flexible devices still lags far behind, mainly being ascribed to the high surface roughness and poor optoelectronic properties of flexible electrodes. Here, we report efficient and robust flexible PeLEDs based on a mixed-dimensional (0D-1D-2D-3D) composite electrode consisting of 0D Ag nanoparticles (AgNPs)/1D Ag nanowires (AgNWs)/2D MXene/3D poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS). Our designed MXene-based electrodes combine the advantages of facile formation of a film of low-dimensional materials and excellent optical and electrical properties of metal, inorganic, and organic semiconductors, which endow the electrodes with high electrical/thermal conductivity, flexibility, a smooth surface, and good transmittance. Consequently, the resulting flexible PeLEDs (without a light-coupling structure) demonstrate a record external quantum efficiency of 16.5%, a high luminance of close to 50000 cd/m², a large emitting area of 8 cm², and significantly enhanced mechanical stability.

Recent Progress of Electrode Materials for Flexible Perovskite Solar Cells

Flexible perovskite solar cells (FPSCs) have attracted enormous interest in wearable and portable electronics due to their high power-per-weight and low cost. Flexible and efficient perovskite solar cells require the development of flexible electrodes compatible with the optoelectronic properties of perovskite. In this review, the recent progress of flexible electrodes used in FPSCs is comprehensively reviewed. The major features of flexible transparent electrodes, including transparent conductive oxides, conductive polymer, carbon nanomaterials and nanostructured metallic materials are systematically compared. And the corresponding modification strategies and device performance are summarized. Moreover, flexible opaque electrodes including metal films, opaque carbon materials and metal foils are critically assessed. Finally, the development directions and difficulties of flexible electrodes are given.

Graphene-Based Hybrid Functional Materials

Graphene is a 2D material combining numerous outstanding physical properties, including high flexibility and strength, extremely high thermal conductivity and electron mobility, transparency, etc., which make it a unique testbed to explore fundamental physical phenomena. Such physical properties can be further tuned by combining graphene with other nanomaterials or (macro)molecules to form hybrid functional materials, which by design can display not only the properties of the individual components but also exhibit new properties and enhanced characteristics arising from the synergic interaction of the components. The implementation of the hybrid approach to graphene also allows boosting the performances in a multitude of technological applications. This review reports the hybrids formed by graphene combined with other low-dimensional nanomaterials of diverse dimensionality (0D, 1D, and 2D) and (macro)molecules, with emphasis on the synthetic methods. The most important applications of these hybrids in the fields of sensing, water purification, energy storage, biomedical, (photo)catalysis, and opto(electronics) are also reviewed, with a special focus on the superior performances of these hybrids compared to the individual, nonhybridized components.

Improved thermal/chemical stability of flexible Ag NWs/Chitosan composite electrode integrated by chemical welding and sequential protection for better PV performance

An integration strategy of chemical welding and subsequent protection was demonstrated to address silver nanowires (Ag NWs)-based issues. Preferentially, a halogenated salt of NaCl solution was used to stimulate the junction welding thus to reduce the junction resistance, by virtue of the autocatalytic redox of Ag atoms with halogen ions and dissolved oxygen molecules. Subsequently, chitosan, possessing the biocompatible, degradable, environmentally friendly non-toxic features, was embedded to protect Ag NWs. With these two steps, the composite electrode consisting Ag NWs and chitosan reaches a lowest sheet resistance of ∼8 Ω, with a transmittance over 80% at 550 nm, along with high thermal and chemical stabilities, accompanying with excellent flexibility. Besides, it also prompts a synergistic improvement when pioneered in Cu(In, Ga)Se₂(CIGS) device as a transparent conductive electrode. It yields a power conversion efficiency of 6.6%, with 32% improvement relative to that bare Ag NWs, and 85% of the conventional one. Our findings present a new strategy for addressing instable/inefficient Ag NWs-based devices, driving their rapid development and its practical applications.

Fabrication of Silver Mesh/Grid and Its Applications in Electronics

With the development of flexible electronics, researchers have endeavored to improve the characteristics of the commonly used indium tin oxide such as brittleness, poor mechanical or chemical stability, and scarcity. Currently, many alternative materials have been considered such as conductive polymers, graphene, carbon nanotubes, metallic nanoparticles (NPs), nanowires (NWs), or nanofibers. Among them, silver (Ag) mesh/grid NPs or NWs have been considered as an excellent substitute due to the good transmittance, excellent electrical conductivity, outstanding mechanical robustness, and cost competitiveness. So far, much effort has been devoted to the fabrication of Ag mesh/grid, and many methods such as printing technology, self-assembly, electrospun, hot-pressing, and atomic layer deposition have been reported. Here printing technologies include jet printing, gravure printing, screen printing, nanoimprint lithography, microcontact printing, and flexographic printing. The solution-based self-assembly usually combines with coating, template, or mask assistance. This review summarizes the characteristics of these fabrication methods for the Ag mesh/grid with its related applications in electronics. Then the prospect and challenges of the fabrication methods are discussed, and the new preparation approaches and applications of the Ag mesh/grid are highlighted, which will be of significance for the applications in electronics such as transparent conducting electrodes, organic light-emitting diode, energy harvester, strain sensor, cells, etc.

All solution-processed silver nanowires composite silica nanospheres antireflection structure with synergetic optoelectronic performance

The silver nanowires/SNSs AR composite TCFs have demonstrated the synergetic effect on optoelectronic performance via a facile solution method, reaching sheet resistance of 49.43 Ω sq−1 dropped by 8.66% and transmittance of 99.84% increased by 6.94%.

Layer-by-Layer Assembly of Electroactive Dye/LDHs Nanoplatelet Matrix Film for Advanced Dual Electro-optical Sensing Applications

It proved that the most destructive effects of the toxic Al3+ ion on the human nervous system and disease that are involved with this system, such as Alzheimer's. The development of solid-state electrodes is still in its infancy during the sensor-based detection methods for Al3+. Hence, in this study, a novel flexible ITO/PET-based electrochemical solid-state sensor was designed and constructed. Modification of the surface of electrode bedding was done by layer-by-layer (LbL) assembly of Mg-Al LDH. nanoplatelets along with alizarin red S (ARS) in an interconnected matrix film. In the molecular design of sensing base of the electrode, the electroactive organic units (ARS molecules) present in the ITO/PET-layered (ARS/LDHs)n matrix are involved in electrochemical reactions when exposed to the target molecule (Al3+ ion), so the electrochemical changes of the new formed Al-chelated system are detectable. This type of sensor is used for sensitive and selective detection of Al3+. The minimum sheet resistance, morphology and high electrocatalytic activity of the modified matrix film are obtained in the fifth cycle of LbL assembly technique. In this electrochemical sensor, both electrochemical and optical methods were detected with high sensitivity and selectivity of Al3+, so that in a cyclic voltammetry electrochemical method, the lower detection limit of 10.1 nM with a linear range of [0.2-120 μM] was obtained compared to the fluorescence-based optical method.

Syntheses of Silver Nanowires Ink and Printable Flexible Transparent Conductive Film: A Review

Nowadays, flexible transparent conductive film (FTCF) is one of the important components of many flexible electronic devices. Due to comprehensive performances on optoelectronics, FTCF based on silver nanowires (AgNWs) networks have received great attention and are expected to be a new generation of transparent conductive film materials. Due to its simple process, printed electronic technology is now an important technology for the rapid production of low-cost and high-quality flexible electronic devices. AgNWs-based FTCF fabricated by using printed electronic technology is considered to be the most promising process. Here, the preparation and performance of AgNW ink are introduced. The current printing technologies are described, including gravure printing, screen printing and inkjet printing. In addition, the latest methods to improve the conductivity, adhesion, and stability of AgNWs-based FTCF are introduced. Finally, the applications of AgNWs-based FTCF in solar cells, transparent film heaters, optoelectronic devices, touch panel, and sensors are introduced in detail. Therefore, combining various printing technologies with AgNWs ink may provide more opportunities for the development of flexible electronic devices in the future.

Biodegradable Materials and Green Processing for Green Electronics

There is little question that the "electronic revolution" of the 20th century has impacted almost every aspect of human life. However, the emergence of solid-state electronics as a ubiquitous feature of an advanced modern society is posing new challenges such as the management of electronic waste (e-waste) that will remain through the 21st century. In addition to developing strategies to manage such e-waste, further challenges can be identified concerning the conservation and recycling of scarce elements, reducing the use of toxic materials and solvents in electronics processing, and lowering energy usage during fabrication methods. In response to these issues, the construction of electronic devices from renewable or biodegradable materials that decompose to harmless by-products is becoming a topic of great interest. Such "green" electronic devices need to be fabricated on industrial scale through low-energy and low-cost methods that involve low/non-toxic functional materials or solvents. This review highlights recent advances in the development of biodegradable materials and processing strategies for electronics with an emphasis on areas where green electronic devices show the greatest promise, including solar cells, organic field-effect transistors, light-emitting diodes, and other electronic devices.

Recent Progress in Organic Photodetectors and their Applications

Organic photodetectors (OPDs) have attracted continuous attention due to their outstanding advantages, such as tunability of detecting wavelength, low-cost manufacturing, compatibility with lightweight and flexible devices, as well as ease of processing. Enormous efforts on performance improvement and application of OPDs have been devoted in the past decades. In this Review, recent advances in device architectures and operation mechanisms of phototransistor, photoconductor, and photodiode based OPDs are reviewed with a focus on the strategies aiming at performance improvement. The application of OPDs in spectrally selective detection, wearable devices, and integrated optoelectronics are also discussed. Furthermore, some future prospects on the research challenges and new opportunities of OPDs are covered.

Promising Hybrid Graphene-Silver Nanowire Composite Electrode for Flexible Organic Light-Emitting Diodes

Thanks to its high transparency, high carrier mobility, and thermal conductivity, graphene is often used as transparent conductive electrode (TCE) in optoelectronic devices. However, the low carrier concentration and high resistance caused by vacancy defects, grain boundaries, and superposed folds in typical graphene films limit its application. In this study, we propose a method to increase both the conductivity and carrier concentration in single-layer graphene (SLG) by blending it with silver nanowires (AgNWs). AgNWs provide connections between grain boundaries of graphene to improve charge-carrier transport. The AgNWs in this study can reduce the resistance of SLG from 650 Ω/◻ to 27 Ω/◻ yet still maintain a transmittance of 86.7% (at 550 nm). Flexible organic light-emitting diode, with a maximum 15000 cd m⁻² luminance was successfully fabricated using such graphene and AgNWs composite transparent electrodes.

Preparation of Ag/graphene composite films by three-component spray-spin-spray coating on surface modified PET substrate

We report a novel method of three-component spray-spin-spray coating to prepare uniform and dense Ag/graphene nanosheet (Ag/GNS) composite films on a surface modified polyethylene terephthalate (PET) substrate. Compared with an untreated sample, the adhesion between composite films and the substrate was significantly enhanced due to the effects of chemical etching and molecular grafting. From the results of the four-probe test, the sheet resistance of hybrid films of Ag/GNS-5 reduced by 60% compared to the pristine Ag films, which was due to the efficient deposition of GNS by spray-spin-spray coating method. Meanwhile, a variety of complex flexible patterns were successfully fabricated with the help of the masking method. This means that the method could provide an efficient and low cost way for flexible electronics production of various complex flexible metallic coatings in practice.

High-density growth of ultrafine PdIr nanowires on graphene: reducing the graphene wrinkles and serving as efficient bifunctional electrocatalysts for water splitting

Manipulating the space distribution states, exposed surfaces, and interfacial interactions of graphene-based nanomaterials is a key strategy for taking full advantage of graphene's characteristics. Herein, we report the in situ deposition of numerous ultrafine PdIr alloy nanowires (diameter of 1.8 nm) to predominately cover the entire surface of graphene (PdIr UNWs/WFG). The high density but low atom loading (8.6 at%) of PdIr nanowires gives rise to abundant edge atoms and a rough surface, which are beneficial for the full exposure of active sites. Meanwhile, the compact PdIr overlay provides strong surface tension to stretch the graphene wrinkles, thus averting the wrapping of active sites and ensuring structural uniformity. The PdIr UNWs/WFG are qualified as efficient and robust electrocatalysts in both the hydrogen evolution reaction (HER) and oxygen evolution reaction (OER), affording 10 mA cm-2 at an HER overpotential of 23 mV and 10 mA cm-2 at an OER overpotential of 290 mV, respectively. The corresponding water electrolyzer requires a cell voltage of only 1.51 V to achieve a water-splitting current density of 10 mA cm-2. This simple and novel approach for studying the coordinated form, dispersion state, and interfacial tension is promising to be a versatile method for improving the properties of graphene-based nanomaterials.

A Universal Stamping Method of Graphene Transfer for Conducting Flexible and Transparent Polymers

Transfer method of chemically vapor deposition graphene is an appealing issue to realize its application as flexible and transparent electrodes. A universal stamping method to transfer as grown graphene from copper onto different flexible and transparent polymers (FTPs) reported here ensures simple, robust, rapid, clean and low-cost. This method relies on coating ethylene vinyl acetate (EVA) onto the as grown graphene, binding EVA coated graphene/Cu with FTPs and delamination by hydrogen bubbling process, which is analogous to the method used by stamping process where ink carries the imprint of the object onto any materials. The fate of the stamping method depends on how strongly the adhesion of EVA coated graphene/Cu with target FTPs. Interestingly, we have found that the thin film of EVA/graphene/Cu can only bind strongly with the FTPs of less than 25 µm in thickness and lower glass transition temperature value to the EVA while wide range of other FTPs are considered upon surface engineering to enhance the binding strength between FTPs and EVA. What’s more, the electrical performance was investigated with a demonstration of triboelectric nanogenerators which confirmed the reliability of graphene transfer onto the FTPs and prospect for the development of flexible and transparent electronics.

Transparent Conductive Electrodes Based on Graphene-Related Materials

Transparent conducting electrodes (TCEs) are the most important key component in photovoltaic and display technology. In particular, graphene has been considered as a viable substitute for indium tin oxide (ITO) due to its optical transparency, excellent electrical conductivity, and chemical stability. The outstanding mechanical strength of graphene also provides an opportunity to apply it as a flexible electrode in wearable electronic devices. At the early stage of the development, TCE films that were produced only with graphene or graphene oxide (GO) were mainly reported. However, since then, the hybrid structure of graphene or GO mixed with other TCE materials has been investigated to further improve TCE performance by complementing the shortcomings of each material. This review provides a summary of the fabrication technology and the performance of various TCE films prepared with graphene-related materials, including graphene that is grown by chemical vapor deposition (CVD) and GO or reduced GO (rGO) dispersed solution and their composite with other TCE materials, such as carbon nanotubes, metal nanowires, and other conductive organic/inorganic material. Finally, several representative applications of the graphene-based TCE films are introduced, including solar cells, organic light-emitting diodes (OLEDs), and electrochromic devices.

Pressure Welding of Silver Nanowires Networks at Room Temperature as Transparent Electrodes for Efficient Organic Light-Emitting Diodes

In this work, polymethylmethacrylate (PMMA) as a superior mediate for the pressure welding of silver nanowires (Ag NWs) networks as transparent electrodes without any thermal treatment is demonstrated. After a pressing of 200 kg cm^-2 , not only the sheet resistance but also the surface roughness of the PMMA-mediated Ag NWs networks decreases from 2.6 kΩ sq^-1 to 34.3 Ω sq^-1 and from 76.1 to 12.6 nm, respectively. On the other hand, high transparency of an average transmittance in the visible wavelengths of 93.5% together with a low haze value of 2.58% can be achieved. In terms of optoelectronic applications, the promising potential of the PMMA-mediated pressure-welded Ag NWs networks used as a transparent electrode in a green organic light-emitting diode (OLED) device is also demonstrated. In comparison with the OLED based on commercial tin-doped indium oxide electrode, the increments of power efficiency and external quantum efficiency (EQE) from 80.1 to 85.9 lm w^-1 and 19.2% to 19.9% are demonstrated. In addition, the PMMA-mediated pressure welding succeeds in transferring Ag NWs networks to flexible polyethylene naphthalate and polyimide substrates with the sheet resistance of 42 and 91 Ω sq^-1 after 10 000 times of bending, respectively.

Screen-Printed Electroluminescent Lamp Modified with Graphene Oxide as a Sensing Device

A screen-printed electroluminescent display with different sensing capabilities is presented. The sensing principle is based on the direct relationship between the light intensity of the lamp and the conductivity of the external layers. The proposed device is able to detect the ionic concentration of any conductive species. Using both top and bottom emission architectures, for the first time, a humidity sensor based on electroluminescent display functionalized by a graphene oxide nanocomposite is introduced. In this regard, just by coupling the display to a smartphone camera sensor, its potential was expanded for automatically monitoring human respiration in real time. Besides, the research includes a responsive display in which the light is spatially turned on in response to pencil drawing or any other conductive media. The above mentioned features together with the easiness of manufacturing and cost-effectiveness of this electroluminescent display can open up great opportunities to exploit it in sensing applications and point-of-care diagnosis.

Defect-Free, Highly Uniform Washable Transparent Electrodes Induced by Selective Light Irradiation

A simple route to fabricate defect-free Ag-nanoparticle-carbon-nanotube composite-based high-resolution mesh flexible transparent conducting electrodes (FTCEs) is explored. In the selective photonic sintering-based patterning process, a highly soft rubber or thin plastic substrate is utilized to achieve close and uniform contact between the composite layer and photomask, with which uniform light irradiation can be obtained with diminished light diffraction. This well-controlled process results in developing a fine and uniform mesh pattern (≈12 μm). The mesh patternability is confirmed to be dependent on heat distribution in the selectively light-irradiated film and the pattern design for FTCE could be adopted for more precise patterns with desired performance. Moreover, using a very thin substrate could allow the mesh to be positioned closer to the strain-free neutral mechanical plane. Due to strong interfacial adhesion between the mesh pattern and substrate, the mesh FTCE could tolerate severe mechanical deformation without performance degradation. It is demonstrated that a transparent heater with fine mesh patterns on thin substrate can maintain stability after 100 repeated washing test cycles in which a variety of stress situations occurring in combination. The presented highly durable FTCE and simple fabrication processes may be widely adoptable for various flexible, large-area, and wearable optoelectronic devices.

Emerging Novel Metal Electrodes for Photovoltaic Applications

Emerging novel metal electrodes not only serve as the collector of free charge carriers, but also function as light trapping designs in photovoltaics. As a potential alternative to commercial indium tin oxide, transparent electrodes composed of metal nanowire, metal mesh, and ultrathin metal film are intensively investigated and developed for achieving high optical transmittance and electrical conductivity. Moreover, light trapping designs via patterning of the back thick metal electrode into different nanostructures, which can deliver a considerable efficiency improvement of photovoltaic devices, contribute by the plasmon-enhanced light-mattering interactions. Therefore, here the recent works of metal-based transparent electrodes and patterned back electrodes in photovoltaics are reviewed, which may push the future development of this exciting field.

Highly-efficient and low-temperature perovskite solar cells by employing a Bi-hole transport layer consisting of vanadium oxide and copper phthalocyanine

In this article, an inorganic–organic bilayer hole transport layer (B-HTL) is designed and utilized in planar perovskite solar cells.

A flexible plasma-treated silver-nanowire electrode for organic light-emitting devices

Silver nanowires (AgNWs) are a promising candidate to replace indium tin oxide (ITO) as transparent electrode material. However, the loose contact at the junction of the AgNWs and residual surfactant polyvinylpyrrolidone (PVP) increase the sheet resistance of the AgNWs. In this paper, an argon (Ar) plasma treatment method is applied to pristine AgNWs to remove the PVP layer and enhance the contact between AgNWs. By adjusting the processing time, we obtained AgNWs with a sheet resistance of 7.2Ω/□ and a transmittance of 78% at 550 nm. To reduce the surface roughness of the AgNWs, a peel-off process was used to transfer the AgNWs to a flexible NOA63 substrate. Then, an OLED was fabricated with the plasma-treated AgNWs electrode as anode. The highest brightness (27000 cd/m²) and current efficiency (11.8 cd/A) was achieved with a 30 nm thick light emitting layer of tris-(8-hydroxyquinoline) aluminum doped with 1% 10-(2-benzothiazolyl)-2,3,6,7-tetrahydro-1,1,7,7-tetramethyl-1H,5 H,11H-(1)-benzopyropyrano(6,7-8-I,j)quinolizin-11-one. Compared to thermal annealing, the plasma-treated AgNW film has a lower sheet resistance, a shorter processing time, and a better hole-injection. Our results indicate that plasma treatment is an effective and efficient method to enhance the conductivity of AgNW films, and the plasma-treated AgNW electrode is suitable to manufacture flexible organic optoelectronic devices.

A flexible plasma-treated silver-nanowire electrode for organic light-emitting devices

Silver nanowires (AgNWs) are a promising candidate to replace indium tin oxide (ITO) as transparent electrode material. However, the loose contact at the junction of the AgNWs and residual surfactant polyvinylpyrrolidone (PVP) increase the sheet resistance of the AgNWs. In this paper, an argon (Ar) plasma treatment method is applied to pristine AgNWs to remove the PVP layer and enhance the contact between AgNWs. By adjusting the processing time, we obtained AgNWs with a sheet resistance of 7.2Ω/□ and a transmittance of 78% at 550 nm. To reduce the surface roughness of the AgNWs, a peel-off process was used to transfer the AgNWs to a flexible NOA63 substrate. Then, an OLED was fabricated with the plasma-treated AgNWs electrode as anode. The highest brightness (27000 cd/m²) and current efficiency (11.8 cd/A) was achieved with a 30 nm thick light emitting layer of tris-(8-hydroxyquinoline) aluminum doped with 1% 10-(2-benzothiazolyl)-2,3,6,7-tetrahydro-1,1,7,7-tetramethyl-1H,5 H,11H-(1)-benzopyropyrano(6,7-8-I,j)quinolizin-11-one. Compared to thermal annealing, the plasma-treated AgNW film has a lower sheet resistance, a shorter processing time, and a better hole-injection. Our results indicate that plasma treatment is an effective and efficient method to enhance the conductivity of AgNW films, and the plasma-treated AgNW electrode is suitable to manufacture flexible organic optoelectronic devices.

Highly Efficient and Stable Organic Solar Cells via Interface Engineering with a Nanostructured ITR-GO/PFN Bilayer Cathode Interlayer

An innovative bilayer cathode interlayer (CIL) with a nanostructure consisting of in situ thermal reduced graphene oxide (ITR-GO) and poly[(9,9-bis(3'-(N,N-dimethylamion)propyl)-2,7-fluorene)-alt-2,7-(9,9-dioctyl) fluorene] (PFN) has been fabricated for inverted organic solar cells (OSCs). An approach to prepare a CIL of high electronic quality by using ITR-GO as a template to modulate the morphology of the interface between the active layer and electrode and to further reduce the work function of the electrode has also been realized. This bilayer ITR-GO/PFN CIL is processed by a spray-coating method with facile in situ thermal reduction. Meanwhile, the CIL shows a good charge transport efficiency and less charge recombination, which leads to a significant enhancement of the power conversion efficiency from 6.47% to 8.34% for Poly({4,8-bis[(2-ethylhexyl)oxy]benzo[1,2-b:4,5-b']dithiophene-2,6-diyl}{3-fluoro-2-[(2-ethylhexyl)carbonyl]thieno[3,4-b]thiophenediyl} (PTB7):[6,6]-phenyl-C71-butyric acid methyl ester (PC71BM)-based OSCs. In addition, the long-term stability of the OSC is improved by using the ITR-GO/PFN CIL when compared with the pristine device. These results indicate that the bilayer ITR-GO/PFN CIL is a promising way to realize high-efficiency and stable OSCs by using water-soluble conjugated polymer electrolytes such as PFN.