A New Generation of Surface Active Carbon Textiles As Reactive Adsorbents of Indoor Formaldehyde

Doping of porous carbons with sulfur and nitrogen markedly enhances their surface activity for formaldehyde removal

The surfaces of phosphoric acid activated carbon, referred to as CG, and steam activated one, referred to as SX, were modified through an introduction of S- and N- groups originated from thiourea. The prepared samples were used for formaldehyde removal at room temperature. Heating at 450, 600 and 950 °C altered both surface chemistry and porosity. The extents of these modifications depended on the type of carbon. Using thiourea as the modifier resulted in an incorporation of significant amounts of nitrogen and sulfur to the carbon matrices. Their speciation depended on the heat treatment conditions. The activity of samples heated at 450 °C was governed by amine groups of thiourea retained on the surface. A further heat treatment converted gradually amine nitrogen into pyridines/pyrroles and quaternary nitrogen, shifting the adsorption mechanism to rather specific interactions than a direct chemical reactivity. Carbons with few times less nitrogen than in their amine-modified counterparts, but in quaternary form and with the small amount of sulfur in thiophenic configurations, regardless the origin, worked as very efficient adsorbents of HCHO. Due to the modification of the carbon matrix electronic structure, resulting in a positive charge on carbon atoms in the vicinity of the heteroatoms incorporated to carbon rings, the density of specific adsorption centers on the surface in larger pores was significantly higher than that in ultramicropores. This markedly contributed to efficient utilization of pores/surface, where heteroatom can exist and where otherwise the dispersive adsorptions forces would be weak, for HCHO removal at ambient conditions.

Electrospun microcrystalline cellulose/chitosan porous composite nanofibrous membranes modified by non-thermal plasma for gaseous formaldehyde adsorption

To develop a green and facile adsorbent for removing indoor polluted formaldehyde (HCHO) gas, the biomass porous nanofibrous membranes (BPNMs) derived from microcrystalline cellulose/chitosan were fabricated by electrospinning. The enhanced chemical adsorption sites with diverse oxygen (O) and nitrogen (N)-containing functional groups were introduced on the surface of BPNMs by non-thermal plasma modification under carbon dioxide (CO2) and nitrogen (N2) atmospheres. The average nanofiber diameters of nanofibrous membranes and their nanomechanical elastic modulus and hardness values decreased from 341 nm to 175-317 nm and from 2.00 GPa and 0.25 GPa to 1.70 GPa and 0.21 GPa, respectively, after plasma activation. The plasma-activated nanofibers showed superior hydrophilicity (WCA = 0°) and higher crystallinity than that of the control. The optimal HCHO adsorption capacity (134.16 mg g-1) of BPNMs was achieved under a N2 atmosphere at a plasma power of 30 W and for 3 min, which was 62.42 % higher compared with the control. Pyrrolic N, pyridinic N, CO and O-C=O were the most significant O and N-containing functional groups for the improved chemical adsorption of the BPNMs. The adsorption mechanism involved a synergistic combination of physical and chemical adsorption. This study provides a novel strategy that combines clean plasma activation with electrospinning to efficiently remove gaseous HCHO.

Diaminopropane-appended activated carbons for the adsorptive removal of gaseous formaldehyde using a portable indoor air purification unit

It is of significant practical interest to develop high-performance air purifier (AP) for removing carcinogenic volatile organic compounds present ubiquitously in indoor air (e.g., formaldehyde (FA)). In this regard, a portable AP system was designed by loading honeycomb ceramic filters with diaminopropane (DAP)-appended activated carbon (AC). The maximum removal efficiencies (REs) of AP loaded with 10, 20, 30, and 50 %-DAP/AC were 26.2, 28, 88.3, and 89.4 %, respectively, against 5 ppm FA (at 160 L min-1). Hence, the 30 % DAP unit was used mainly in this work. The removal efficiency of 30 %-DAP/AC (160 L min-1), when tested against 2 ppm FA, decreased from 90.3 to 73.2 % with an increase in relative humidity from 0 to 60 %. The performance of the AP unit, when assessed kinetically in terms of the clean air delivery rate (CADR), reached as high as 10.2 L min-1 at the flow rate of 160 L min-1. Isotherm analysis further demonstrated the complex multilayered adsorption behavior of FA. Based on the density functional theory (DFT) simulation, the superiority of DAP/AC for FA adsorption can be attributed to the synergy of covalent (chemisorption) and non-covalent (pore filling and film diffusion) interactions.

Recycling and Reusing of Graphite from Retired Lithium-ion Batteries: A Review

The proliferation of rechargeable lithium-ion batteries (LIBs) over the past decade has led to a significant increase in the number of electric vehicles (EVs) powered by these batteries reaching the end of their lifespan. With retired EVs becoming more prevalent, recycling and reusing their components, particularly graphite, has become imperative as the world transitions toward electric mobility. Graphite constitutes ≈20% of LIBs by weight, making it a valuable resource to be conserved. This review presents an in-depth analysis of the current global graphite mining landscape and explores potential opportunities for the "second life" of graphitefrom depleted LIBs. Various recycling and reactivation technologies in both industry and academia are discussed, along with potential applications for recycled graphite forming a vital aspect of the waste management hierarchy. Furthermore, this review addresses the future challenges faced by the recycling industry in dealing with expired LIBs, encompassing environmental, economic, legal, and regulatory considerations. In conclusion, this review provides a comprehensive overview of the developments in recycling and reusing graphite from retired LIBs, offering valuable insights for forthcoming large-scale recycling efforts.

Formulating the Li sites of Li-CoOx composites for achieving high-efficiency oxidation removal of formaldehyde over the Ag/Li-CoOx catalyst under ambient conditions

Oxide supported noble metals are extensively investigated for ambient formaldehyde oxidation, and the Ag-CoOx complex is one promising combination in terms of cost and activity. Further, we previously observed that cooperating Ag with Li + greatly boosted formaldehyde degradation on CoOx. Yet, there is still room for improvement in removal efficiency, mineralization capacity and resistance to severe conditions. These objectives could be realized via strategically formulating the Li+ sites of Li-CoOx composite in this sister study. Three samples with Li + ---Co3+-O2- connections (L-CO), spinel Li+ (LCO-S) and layered Li+ (LCO-L) were obtained at low (300 °C), moderate (500 °C) and high (700 °C) temperatures, respectively. The specific Li+ positions and componential interaction were demonstrated by Hyperspectral imaging (HSI), XRD, SEM, TEM, HAADF mapping, UV-vis DRS and XPS. Moreover, the effect of reactive oxygen exposure on catalytic oxidation of formaldehyde (330-350 mg/m3) was disclosed through CO-TPR and O2-TPD. Compared with the LCO-S and LCO-L, L-CO exhibited dominant formaldehyde degradation due to the larger content of surface oxygen. After Ag decoration, the Li+---Co3+-O2- connections uniquely caused a strong binding of Ag species with catalyst host, which boosted the amount of reactive oxygen and finally resulted in an even higher elimination of ∼73% (CO2 yield = ∼21%), 47% higher than that of the L-CO (CO2 yield = ∼6%). But in contrast, the Ag@LCO-S only achieved ∼53% removal (CO2 yield = ∼9%) and Ag modification was powerless in altering the inertness of LCO-L, demonstrating that the chemical environment of alkali metal is crucial to effectively tuning the catalyst activity. The advantage of Ag@L-CO in formaldehyde depollution was further reflected from its much better resistance to moisture and aromatic compound omnipresent in indoor air. For the first time, this study extended the understanding of the alkali-metal-promoted formaldehyde oxidation reaction to an in-depth level.

Removal of Formaldehyde and Its Analogues Using a Hybrid Assembly of Pyrene-Modified Hydrazide and rGO: A Negative Carbon Emission and Green Chemical Decomposition Method

Indoor gaseous formaldehyde is the main environmental pollutant that can cause fatal threats to human health. A number of physical and chemical methods have been developed to tackle this issue. However, the existing methods are still unsatisfactory to meet the requirement of sustainable development owing to the flaws of low efficiency and reversible or second pollution. Herein, a chemical method based on a nucleophilic reaction between hydrazine and aldehyde that generates the only by-product of H₂O is designed for the removal of formaldehyde. 1-Pyrenebutyric hydrazide was synthesized by a simple esterification reaction and then self-assembled on reduced graphene oxide (rGO) with a large surface area by forming π-π stacking to obtain a composite for chemical removal of gaseous formaldehyde under ambient conditions. In a practical test, the formaldehyde removal rate could reach 91% of the theoretical value, which meets the requirement for commercial formaldehyde removal applications. After 10 times recycling, the formaldehyde removal rate still remains as high as 85%. Moreover, the composite could be regenerated in weak acidic media, which greatly reduce the manufacturing cost in practical applications.

Self-Assembled Construction of Robust and Super Elastic Graphene Aerogel for High-Efficient Formaldehyde Removal and Multifunctional Application

Simultaneously achieving exceptional mechanical strength and resilience of graphene aerogel (GA) remains a challenge, while GA is an ideal candidate for formaldehyde removal. Herein, flexible polyethyleneimine (PEI) is grafted chemically onto carbon nanotube (CNT) surface, and CNT-PEI@reduced GA (rGA) is fabricated via hydrothermal self-assembly, pre-frozen, and hydrazine reduction process. Introducing CNT-PEI contributes to well-interconnected/robust 3D network construction by connecting reduced graphene oxide (rGO) nanosheets through enhancing cross-linking, while entangled CNT-PEI is intercalated into rGO layers to avoid serious restacking of sheets, producing larger surface area and more formaldehyde adsorption sites. Ultralight CNT-PEI@rGA exhibits extreme high strength (276.37 kPa), reversible compressibility at 90% strain, and structural stability, while FA adsorption capacity reached 568.41 mg g^-1 , ≈3.28 times of rGA, derivable from synergistic chemical-physical adsorption effect. Furthermore, CNT-PEI@rGA is ground into powder for first preparing polyoxymethylene (POM)/CNT-PEI@rGA composite, while formaldehyde emission amount is 69.63%/73.96% lower than that of POM at 60/230 °C. Moreover, CNT-PEI@rGA presents outstanding piezoresistive-sensing and thermal insulation properties, exhibiting high strain sensitivity, wide strain detection range, and long-term durability.

Rare-earth-doped indium oxide nanosphere-based gas sensor for highly sensitive formaldehyde detection at a low temperature

Formaldehyde (HCHO) is widely viewed as a carcinogenic volatile organic compound in indoor air pollution that can seriously threaten human health and life. Thus, there is a critical need to develop gas sensors with improved sensing performance, including outstanding selectivity, low operating temperature, high responsiveness, and short recovery time, for HCHO detection. Currently, doping is considered an effective strategy to raise the sensing performance of gas sensors. Herein, various rare earth elements-doped indium oxide (RE-In₂O₃) nanospheres were fabricated as gas sensors for improved HCHO detection via a facile and environmentally solvothermal method. Such RE-In₂O₃ nanosphere-based sensors exhibited remarkable gas-sensing performance, including a high selectivity and stability in air. Compared with pure, Yb-, Dy-doped In₂O₃ and different La ratios doped into In₂O₃, 6% La-doped In₂O₃ (La-In₂O₃) nanosphere-based sensors demonstrated a high response value of 210 to 100 ppm at 170 °C, which was around 16 times higher than that of the pure In₂O₃ sensor, and also exhibited a detection limit of 10.9 ppb, and a response time of 30 s to 100 ppm HCHO with a recovery time of 160 s. Finally, such superior sensing performance of the 6% La-In₂O₃ sensors was proposed to be attributed to the synergistic effect of the large specific surface area and enhanced surface oxygen vacancies on the surface of In₂O₃ nanospheres, which produced chemisorbed oxygen species to release electrons and provided abundant reaction sites for HCHO gas. This study sheds new light on designing nanomaterials to build gas sensors for HCHO detection.

Zero-Carbon Emission Chemical Method to Remove Formaldehyde without Catalyst by Highly Porous Polymer Composites at Room Temperature

Herein, the fabrication of reduced graphene oxide (RGO)-templated polymer composites for chemical removal of gaseous formaldehyde under ambient conditions is presented. The chemical removal of formaldehyde is achieved by a nucleophilic addition reaction between formaldehyde and aminooxy groups on the polymer chain ends to form the oxime bonds with the only byproduct of H₂ O. RGO is essential since it not only has an ultralarge surface area but also can act as a perfect template for immobilizing pyrene-terminated and aminooxy-functionalized polymers via strong π-π stacking interactions, while melamine foam provides a three-dimensional skeleton for loading RGO/polymer composites to afford a porous 3D structure for efficient formaldehyde removal. Since the oxime bond can be cleaved into aminooxy group in acidic media, the RGO/polymer composite can be regenerated for repeatable usage, which shows an excellent performance of adsorbing 14 mg of formaldehyde by 100 mg of the polymer at ambient condition.

Novel B and N Sites of One-Dimensional Boron Nitride Fiber: Efficient Performance and Mechanism in the Formaldehyde Capture Process

Identification of adsorption centers with atomic levels of adsorbents is crucial to study the adsorption of formaldehyde (HCHO), especially for an in-depth understanding of the mechanism of HCHO capture. Herein, we investigate the HCHO adsorption performance of one-dimensional (1D) nanoporous boron nitride (BN) fiber, and explore the adsorption mechanism by density functional theory (DFT) calculations, including adsorption energy change and Bader charge change, and experimental study as well. Research shows that the 1D nanoporous BN fiber possesses a high concentration of Lewis pairs, which act as Lewis acid and Lewis base sites associated with the fiber's electron-deficient and electron-rich features. It is worth noting that the HCHO removal efficiency of a typical sample is as high as 91%. This work may open the door to the field of adsorption of other pollutants by constructing Lewis pairs in the future.

A Brief Review of Formaldehyde Removal through Activated Carbon Adsorption

Formaldehyde is a highly toxic indoor pollutant that can adversely impact human health. Various technologies have been intensively evaluated to remove formaldehyde from an indoor atmospheres. Activated carbon (AC) has been used to adsorb formaldehyde from the indoor atmosphere, which has been commercially viable owing to its low operational costs. AC has a high adsorption affinity due to its high surface area. In addition, applications of AC may be diversified by the surface modification. Among the different surface modifications for AC, amination treatments of AC have been reported and evaluated. Specifically, the amine functional groups of the amine-treated AC have been found to play an important role in the adsorption of formaldehyde. Surface modifications of AC by impregnating and/or grafting the amine functional groups onto the AC surface have been reported in the literature. The impregnation of the amine-containing species on AC is mainly achieved by physical interaction or H-bond of the amines to the AC surface. Meanwhile, the grafting of the amine functional groups is mainly conducted through chemical reactions occurring between the amines and the AC surface. Herein, the carboxyl group, as a representative functional group for grafting on the surface of AC, plays a key role in the amination reactions. A qualitative comparison of amination chemicals for the surface modification of AC has also been discussed. Thermodynamics and kinetics for adsorption of formaldehyde on AC are firstly reviewed in this paper, and then the major factors affecting the adsorptive removal of formaldehyde over AC are highlighted and discussed in terms of humidity and temperature. In addition, new strategies for amination, as well as the physical modification option for AC application, are proposed and discussed in terms of safety and processability.

One-Pot Method to Synthesize Silver Nanoparticle-Modified Bamboo-Based Carbon Aerogels for Formaldehyde Removal

The present study demonstrated a freeze-drying-carbonization method to synthesize silver nanoparticle-modified bamboo-based carbon aerogels to remove formaldehyde. The bamboo-based carbon aerogel (BCA) has the advantages of controllable pore size and rich oxygen-containing groups, which can provide a good foundation for surface modification. BCA can greatly enhance the purification of formaldehyde by loading silver nanoparticles. The maximum adsorption capacity of 5% Ag/BCA for formaldehyde reached 42 mg/g under 25 ppm formaldehyde concentration, which is 5.25 times more than that of BCA. The relevant data were fitted by the Langmuir model and the pseudo 2nd-order model and good results were obtained, indicating that chemical absorption occurred between the carbonyl of formaldehyde and the hydroxyl of BCA. Therefore, silver nanoparticle-modified bamboo-based carbon aerogels play a positive role in the selective removal of formaldehyde. Silver nanoparticles promoted the activation of oxygen and strengthened the effect of BCA on HCHO adsorption.

Introducing Polyhydroxyurethane Hydrogels and Coatings for Formaldehyde Capture

Formaldehyde (FA) is a harmful chemical product largely used for producing resins found in our living spaces. Residual FA that leaches out the resin contributes to our indoor air pollution and causes some important health issues. Systems able to capture this volatile organic compound are highly desirable; however, traditional adsorbents are most often restricted to air filtration systems. Herein, we report novel waterborne coatings that are acting as a FA sponge for indoor air decontamination. These coatings, of the poly(hydroxyurethane) (PHU) type, rich in primary amine groups, are prepared by the polyaddition of a hydrosoluble dicyclic carbonate to a polyamine in water at room temperature under catalyst-free conditions. We highlight the importance of the choice of the polyamine on the curing rate of the formulation and on the FA capture ability of PHU. The excellent FA capturing ability of the best candidate is rationalized by investigating the action mode of the polyamine used to construct PHUs. With poly(vinyl amine), FA is covalently and permanently bound to PHU, with no release over time. The performance of the coating in FA abatement is impressive, with more than 90% of captured FA after one day of contact. The facility to prepare these transparent and colorless coatings from waterborne formulations gives access to new efficient indoor air depolluting solutions, potentially applicable to various surfaces of our living spaces (wall, ceiling, etc.).

Recent progress on removal of indoor air pollutants by catalytic oxidation

Indoor air pollutant is a serious problem due to its wide diversity and variability. The harmful substances from construction materials and decorative materials may make the indoor air pollution become more and more serious and cause serious health problems. In this paper, the review summarizes the advanced technologies for the removal of indoor air pollutants and the development in the treatment of indoor air pollution by catalytic oxidation technologies. Meanwhile, some catalytic oxidation mechanisms of indoor air pollutants are proposed in detail, and suggestions for the indoor air pollution treatment are also presented, in order to provide some reference for subsequent research.

An efficient strategy for the enhancement of adsorptivity of microporous carbons against gaseous formaldehyde: Surface modification with aminosilane adducts

In an effort to develop a cost-effective mitigation tool for volatile organic compounds, particularly formaldehyde (FA), microporous activated carbon (AC) was modified into three different forms of AC-1, AC-2, and AC-3 using a raw commercial AC product (AC-0). First, AC-1 and AC-2 were produced by the modification of AC-0 with N/S heteroatoms using identical mixture of dicyandiamide and thiourea precursors through either solvothermal (AC-1) or microwave-assisted calcination (AC-2) synthesis. Second, aminosilane-functionalized AC (AC-3) was prepared solvothermally using N-[3-(Trimethoxysilyl)propyl]ethylenediamine reagent. The relative adsorption performances for gaseous FA (1 ppm) in terms of 10% breakthrough volume (BTV10: L atm g^-1) at near-ambient conditions (25 °C and 1 atm) were AC-3 (132) > AC-2 (66.5) > AC-1 (14.2) > AC-0 (10.4). In a comparison based on partition coefficients (mole kg^-1 Pa^-1) at BTV10, AC-3 outperformed AC-0 by a factor of 214, while the adsorption performance of AC-2 was 36-times higher than AC-1. The enhanced performance of AC-2 over AC-1 reflected the effect of the microwave synthesis protocol on the improvement of surface chemistry (e.g., N/S doping) and texture (e.g., surface area and pore volume) of AC-based adsorbents as compared to conventional solvothermal method. Further, the prominent role of surface chemistry (e.g., relative to textural properties), as observed with the increases in the amount of doped functional elements (including N:C and silicon:C ratios), is supported by the apparent dependence of performance on the selected modification procedures. Based on kinetic and X-ray photoelectron spectroscopy analyses, the superiority of aminosilylated AC-3 can be attributed to a synergistic effect between physisorption (e.g., pore diffusion) and chemical interactions of the FA carbonyl (C=O) group with amine and silica functionalities (via Mannich coupling [Schiff base] and cycloaddition reaction mechanisms, respectively). This confirms the significance of surface chemistry, relative to pore diffusion, in achieving maximum adsorption of gaseous FA molecules.

Reusable fibrous adsorbent prepared via Co-radiation induced graft polymerization for iodine adsorption

Volatile iodine released from nuclear power plant reactors is radiological hazard to environment and human's health because of their high fission yield and environmental mobility. The complexity of nuclear waste management motivated the development of solid-phase adsorbents. Herein, co-radiation induced graft polymerization (CRIGP) was employed in the graft polymerization of N-vinyl-2-pyrrolidone (NVP) onto polyethylene-coated polypropylene skin-core (PE/PP) fibers using electron beam (EB) irradiation. This work provides a one-step green synthetic approach to prepare iodine fibrous adsorbents without any chemical initiators or large amount of organic solvent. The original and modified PE/PP fibers were characterized by fourier transform infrared spectrometry (FTIR), X-ray photoelectron spectroscopy (XPS), thermogravimetric (TG) and scanning electron microscopy (SEM) to demonstrate the grafting of NVP onto the PE/PP fibers. The capacity of iodine absorbed by the PE/PP-g-PNVP fibers was 1237.8 mg/g after 180 min. Meanwhile, absorbents can be regenerated efficiently by two different means of ethanol elution and heating at 120 °C, respectively. Within 10 min, 94.17% and 90.12% of the iodine can be released from the PE/PP-g-PNVP fibers with these two methods, respectively. The adsorbent exhibited a long service life of at least ten adsorption-desorption cycles, suggesting that PE/PP-g-PNVP fibers might be a promising adsorbent for volatile iodine adsorption from fission products in nuclear power plant reactors.

Tailoring Surface Chemistry of Sugar-Derived Ordered Mesoporous Carbons Towards Efficient Removal of Diclofenac From Aquatic Environments

Ordered mesoporous carbon (CMK-3), obtained from an abundant natural source, sugar, was thermochemically modified with dicyandiamide and thiourea as well as by classical oxidization with hydrogen peroxide to introduce specific surface groups. Thermochemical modifications resulted in carbon with almost unchanged porosity and altered surface chemistry while porosity of H₂O₂-treated carbon was seriously deteriorated. The obtained carbons were tested as sorbents of diclofenac, considered as one of the emerging water contaminants. Changes in porosity and surface chemistry of modified carbons resulted in significant differences with regard to the uptake of diclofenac. Dicyandiamide-modified carbon showed highest uptake of drugs, reaching 241 mg g⁻¹ that is attributed to its developed microporosity as well as surface chemistry composed of basic groups facilitating electrostatic interactions with diclofenac anions. Desorption study showed that diclofenac is strongly bonded, albeit with a different degree depending on the modification of the CMK-carbon. The obtained results were compared with up-to-date literature regarding sorption of diclofenac by carbon-based sorbents.

Adsorption properties of advanced functional materials against gaseous formaldehyde

Intense efforts have been made to eliminate toxic volatile organic compounds (VOCs) in indoor environments, especially formaldehyde (FA). In this study, the removal performances of gaseous FA using two metal-organic frameworks, MOF-5 and UiO-66-NH₂, and two covalent-organic polymers, CBAP-1 (EDA) and CBAP-1 (DETA), along with activated carbon as a conventional reference material, were evaluated. To assess the removal capacity of FA under near-ambient conditions, a series of adsorption experiments were conducted at its concentrations/partial pressures of both low (0.1-0.5 ppm/0.01-0.05 Pa) and high ranges (5-25 ppm/0.5-2.5 Pa). Among all tested materials at the high-pressure region ㅐ (e.g., at 2.5 ppm FA), a maximum adsorption capacity of 69.7 mg g^-1 was recorded by UiO-66-NH₂. Moreover, UiO-66-NH₂ also displayed the best 10% breakthrough volume (BTV10) of 534 L g^-1 (0.5 ppm FA) to 2963 L g^-1 (0.1 ppm FA). In contrast, at the high concentration test (at 5, 10, and 25 ppm FA), the maximum BTV10 values were observed as: 137 (UiO-66-NH₂), 144 (CBAP-1 (DETA)), and 36.8 L g^-1 (CBAP-1 (EDA)), respectively. The Langmuir isotherm model was observed to be a better fit of the adsorption data than the Freundlich model under most of the tested conditions. The superiority of UiO-66-NH₂ was attributed to the van der Waals interactions between the linkers (framework) and the hydrocarbon "tail" (FA) coupled with interactions between its open metal sites and the FA carbonyl groups. This study demonstrated the good potential of these advanced functional materials toward the practical removal of gaseous FA in indoor environments.

High-performance materials for effective sorptive removal of formaldehyde in air

As formaldehyde (FA) is well-known for its carcinogenic potential, various techniques for its removal have been developed based on recovery (e.g., adsorption/absorption and condensation) or destructive treatment (e.g., incineration and thermal/ catalytic oxidation). Among them, adsorption has been one of the most preferable options due to its low price and simplicity. In this review, we summarize state-of-the-art knowledge about adsorption mechanisms with respect to its key controlling variables (e.g., surface chemical properties of adsorbent, temperature, and relative humidity) and adsorption performance of materials with particular emphasis on advanced materials (e.g., carbon nanotubes, metal-organic frameworks, graphene oxides, and porous organic polymers) and their modified forms in comparison with conventional sorbents (e.g., AC and zeolite). However, it is yet difficult to assess the adsorption capacity of each material on a parallel basis because adsorption experiments of each material were conducted under different conditions (e.g., large differences in the initial loading concentrations). The partition coefficient (PC) was employed for evaluating adsorption performance between different materials at an equivalent level to overcome the limitation based on adsorption capacity concept. For instance, among the list of the surveyed materials, the highest PC was recorded by γ-CD-MOF-K (31.2 mol kg^-1 Pa^-1). This study should offer valuable insights into the selection and development of outstanding materials for the sorptive removal of FA.

A TiO2/C catalyst having biomimetic channels and extremely low Pt loading for formaldehyde oxidation

This study presents a TiO2/C hybrid material with biomimetic channels fabricated using a wood template. Repeated impregnations of pretreated wood chips in a Ti precursor were conducted, followed by calcination at 400-600 °C for 4 hours under a nitrogen atmosphere. The generated TiO2 nanocrystals were homogenously distributed inside a porous carbon framework. With an extremely low Pt catalyst loading (0.04-0.1 wt%), the obtained porous catalyst could effectively oxidize formaldehyde to CO2 and H2O even under room temperature (conv. ∼100%). Wood acted as both a structural template and reduction agent for Pt catalyst generation in sintering. Therefore, no post H2 reduction treatment for catalyst activation was required. The hierarchal channel structures, including 2-10 nm mesopores and 20 μm diameter channels, could be controlled by calcination temperature and atmosphere, which was confirmed by SEM and BET characterizations. Based on the abundant availability of wood templates and reduced cost for low Pt loading, this preparation method shows great potential for large-scale applications.