Open and Hierarchical Carbon Framework with Ultralarge Pore Volume for Efficient Capture of Carbon Dioxide

Amine-Functionalized Meso-Macroporous Polymers for Efficient CO2 Capture from Ambient Air

Over the past decade, direct air capture (DAC) of carbon dioxide (CO2) using solid nanoadsorbents has garnered attention as a negative emission technology with high energy efficiency. Although operational, the large-scale deployment of DAC technologies has been significantly delayed due to the low performance and high cost of solid DAC nanoadsorbents. Herein, we present a novel family of meso-macroporous melamine formaldehyde (MF) materials with a facile preparation methodology, low capital cost, and unique physicochemical characteristics for DAC. The fabricated MF materials exhibit an extra-large pore volume of 5.19 cm3/g with a 24.6 nm average pore diameter. We show that the synthesized MF materials can be used as substrates and impregnated with different amounts of tetraethylenepentamine (TEPA) to act as chemical nanoadsorbents for DAC. Owing to the ultrahigh pore volume of MF, a substantial amount of 71 wt % TEPA (i.e., MF-TEPA71%) can be loaded, resulting in 2.65 mmol/g of CO2 uptake under DAC conditions. In addition, the superior physicochemical properties of MF lead to a high CO2 loading of 2.07 mmol/g with low TEPA loading in MF-TEPA33%. The prepared MF-TEPA nanoadsorbents can be successfully employed in different shapes (i.e., droplets, pellets, and coatings) and maintain their superiority across different temperatures and CO2 concentrations. This study provides a promising approach for developing meso-macroporous substrates through a straightforward and scalable synthesis method, representing a new avenue for the next generation of DAC nanoadsorbents with superior performance for practical applications.

Improvement in CO2 Capture of Polyamine with Micro-Interfacial System

Polyamines have emerged as a promising class of CO2 absorbents due to their remarkable sequestration capacity. However, their potential industrial application as aqueous absorbents is significantly hindered by a low regeneration efficiency and high energy consumption. To address these issues, this study investigates the use of triethylenetetramine (TETA) and ethylene glycol (EG) to develop a nonaqueous absorbent. The incorporation of EG enhances absorption performance and reduces the regeneration energy needed for TETA, whereas the high viscosity of the absorbent impedes absorption rate, amine efficiency, and regeneration efficiency. In order to enhance CO2 capture, micron-sized reaction units (SiO2@TETA-EG) were developed by encapsulating TETA solution with nanosilica. The SiO2@TETA-EG composite exhibits a large specific surface area (99 m2/g), with a porous shell structure and improved fluidity, which effectively counteracts the negative effects caused by high viscosity. Notably, SiO2@TETA-EG indicates a noticeably higher apparent rate constant of 4.29 min-1 at 323.2 K compared to the TETA-EG solution. Furthermore, SiO2@TETA-EG displays a 28.4% boost in regeneration efficiency while maintaining favorable stability in pore size and shape after regeneration.

Biochar Derived from Chinese Herb Medicine Residues for Rhodamine B Dye Adsorption

In this study, one well-known CHM residue (Atropa belladonna L., ABL) was used to prepare biochar capable of adsorbing rhodamine B (RhB) with an ultrahigh surface area for the first time. Three micropore-rich ABL biochars including ABL@ZnCl₂ (1866 m²/g), ABL@H₃PO₄ (1488 m²/g), and ABL@KOH (590 m²/g) were obtained using the one-step carbonization method with activation agents (ZnCl₂, H₃PO₄, and KOH) via chemical activation and carbonization at 500 °C, and their adsorption performance for RhB was systematically studied with adsorption kinetics, isotherms, and thermodynamics. Through pore diffusion, π-π interaction, and hydrogen bonding, ABL biochar had excellent adsorption performance for RhB. Moreover, when C ₀ was 200 mg/L, biochar dosage was 1 g/L, and the contact time was 120 min; the maximum RhB adsorption capacity and removal efficiency on ABL@ZnCl₂ and ABL@H₃PO₄ were 190.63 mg/g, 95% and 184.70 mg/g, 92%, respectively, indicating that it was feasible to prepare biochar from the ABL residue for RhB adsorption. The theoretical maximum adsorption capacities of ABL@ZnCl₂ and ABL@H₃PO₄ for RhB were 263.19 mg/g and 309.11 mg/g at 25 °C, respectively. Furthermore, the prepared biochar showed good economic applicability, with pay back of USD 972/t (ABL@ZnCl₂) and USD 987/t (ABL@H₃PO₄), respectively. More importantly, even after five cycles, ABL@H₃PO₄ biochar still showed great RhB removal efficiency, suggesting that it had a good application prospect and provided a new method for the resource utilization of traditional CHM residues. Additionally, pore diffusion, π-π interactions, and hydrogen bonding all play roles in the physical adsorption of RhB on ABL biochar. π-π interactions dominated in the early stage of RhB adsorption on ABL@H₃PO₄, while pore diffusion played a crucial role in the whole adsorption process on both adsorbents.

One-Step Synthesis of 3D Pore-Structured Adsorbent by Cross-Linked PEI and Graphene Oxide Sheets and Its Application in CO2 Adsorption

In this study, a one-step method of polyethylenimine (PEI) cross-linking graphene oxide (GO) was used to prepare a 3D pore-structured adsorbent with abundant amine groups for chemisorption of CO₂. The cross-linking of PEI with GO sheets and the vacuum freeze-drying step are the keys to the formation of the 3D pore structure. The results of characterization analysis revealed that the as-prepared adsorbent had a 3D porous structure rich in amine groups. Besides, the adsorption/desorption test showed that the prepared adsorbent has excellent and stable adsorption performance, and the maximum CO₂ adsorption capacity is 2.18 mmol/g at 343 K and 10 vol % CO₂. Moreover, the adsorption kinetics analysis indicated that the adsorption process was dominated by homogeneous adsorption, and the adsorbent had a strong affinity with CO₂. Finally, the correlation analysis shows that the kinetic constants obtained by the Avrami model simulation can be effectively used for the actual CO₂ adsorption process design.

Nano-Structured Carbon: Its Synthesis from Renewable Agricultural Sources and Important Applications

Carbon materials are versatile in nature due to their unique and modifiable surface and ease of production. Nanostructured carbon materials are gaining importance due to their high surface area for application in the energy, biotechnology, biomedical, and environmental fields. According to their structures, carbon allotropes are classified as carbon nanodots, carbon nanoparticles, graphene, oxide, carbon nanotubes, and fullerenes. They are synthesized via several methods, including pyrolysis, microwave method, hydrothermal synthesis, and chemical vapor deposition, and the use of renewable and cheaper agricultural feedstocks and reactants is increasing for reducing cost and simplifying production. This review explores the nanostructured carbon detailed investigation of sources and their relevant reports. Many of the renewable sources are covered as focused here, such as sugar cane waste, pineapple, its solid biomass, rise husk, date palm, nicotine tabacum stems, lapsi seed stone, rubber-seed shell, coconut shell, and orange peels. The main focus of this work is on the various methods used to synthesize these carbon materials from agricultural waste materials, and their important applications for energy storage devices, optoelectronics, biosensors, and polymer coatings.

Preparation of a Fiber-Like 3D-Structured Adsorbent for CO2 Capture

Solid amine adsorbents are promising materials to mitigate global warming. In this study, a commercially available melamine-formaldehyde sponge was adopted as a support to prepare a kind of solid amine adsorbent using polyethylenimine as a functional component and ethylene glycol diglycidyl ether as a cross-linker. The adsorbent, with abundant tunnels and a high amine loading amount, had a high adsorption capacity. When the amine loading was 89.6 wt%, the as-prepared adsorbent showed a high adsorption capacity of 7.29 mmol/g at 20 °C in the presence of water. The spent adsorbent could be easily regenerated by heating it at 90 °C, resulting in lower energy consumption. It has been proved by the Avrami model that physical and chemical adsorption coexist in the adsorption of CO₂ on this adsorbent. Simulation with the intraparticle diffusion model has revealed that the rate-controlling step in the adsorption process was the gas film diffusion period when the adsorption temperature was below 30 °C, while it was the adsorption equilibrium period when the adsorption temperature was above 30 °C.

Transforming Porous Silica Nanoparticles into Porous Liquids with Different Canopy Structures for CO2 Capture

Porous liquids (PLs) have both liquid fluidity and solid porosity, thereby offering a variety of applications, such as gas sorption and separation, homogeneous catalysis, energy storage, and so forth. In this research, canopies with varying structures were utilized to modify porous silica nanoparticles to develop Type I PLs. According to experimental results, the molecular weight of canopies should be high enough to maintain the porous materials in the liquid state at room temperature. Characterization results revealed that PL_1_M2070 and PL_1_AC1815 displayed low viscosity and good fluidity. Both low temperature and high pressure positively influenced CO₂ capacity. The cavity occupancy resulted in poorer sorption capacity of PLs with branched canopies in comparison with that with linear canopies. Furthermore, the sorption capacity of PL_1_M2070 was 90.5% of the original CO₂ sorption capacity after 10 sorption/desorption cycles, indicating excellent recyclability.

Different functional groups modified porous organic polymers used for low concentration CO2 fixation

Through a facile post-synthetic method, different kinds of polar group-functionalized ionic liquid porous organic polymers (POP-PA-COOH, POP-PA-OH, and POP-PA-NH₂) were obtained. The materials can be used as efficient heterogeneous catalysts in the cycloaddition reaction of CO₂ with epoxides under mild and co-catalyst-free conditions. It is demonstrated that POP-PA-NH₂ possesses much higher catalytic activity than POP-PA-OH and POP-PA-COOH. Interestingly, this activity difference can further be amplified when the reaction is carried out under low CO₂ concentration, and POP-PA-NH₂ possesses a conversion of 84.7% with a selectivity of 99.0% in 96 h. It is noteworthy to mention that research focusing on the transformation of CO₂ under low concentration using heterogeneous catalysts is rare and still a challenge. The excellent activities of POP-PA-NH₂ under low CO₂ concentration make this material a good candidate for CO₂ elimination under mild conditions.

What Fluorine Can Do in CO2 Chemistry: Applications from Homogeneous to Heterogeneous Systems

CO₂ chemistry including capture and fixation has attracted great attention towards the aim of reducing the consumption of fossil fuels and CO₂ accumulation in the atmosphere. "CO₂ -philic" materials are required to achieve good performance owing to the intrinsic properties of the CO₂ molecule, that is, thermodynamic stability and kinetic inertness. In this respect, fluorinated materials have been deployed in CO₂ capture (physical and chemical pathway) or fixation (thermo- and electrocatalytic procedure) with good performances, including homogeneous (e. g., ionic liquids and small organic molecules) and heterogeneous counterparts (e. g., carbons, porous organic polymers, covalent triazine frameworks, metal-organic frameworks, and membranes). In this Minireview, these works are summarized and analyzed from the aspects of (1) the strategy used for fluorine introduction, (2) characterization of the targeted materials, (3) performance of the fluorinated systems in CO₂ chemistry, and comparison with the nonfluorinated counterparts, (4) the role of fluorinated functionalities in the working procedure, and (5) the relationship between performance and structural/electronic properties of the materials. The systematic summary in this Minireview will open new opportunities in guiding the design of "CO₂ -philic" materials and pave the way to stimulate further progress in this field.

Preparation of a Solid Amine Microspherical Adsorbent with High CO2 Adsorption Capacity

Amine-skeleton solid-amine materials are promising adsorbents for CO₂ capture from flue gas. Here, a novel solid-amine microsphere was synthesized by cross-linking the skeleton poly(ethylenimine) (PEI) with ethylene glycol diglycidyl ether in a facile one-pot W/O emulsion system. The material had a remarkable CO₂ adsorption capacity of 7.28 mmol/g in the presence of moisture at 20 °C, 0.1 bar. The highest ratio of breakthrough capacity to saturation capacity was ca. 84%. According to kinetic simulation, the Avrami kinetic model could better describe the adsorption process of CO₂ under different temperatures, in which the value of R² was above 0.99 and n was between 1 and 2, indicating that both physical and chemical adsorption mechanisms were performed during adsorption. Moreover, the material had a high swelling speed. Equilibrium was established within 30 s, and the swelling ratio was 271% at equilibrium. The saturated adsorbent could be easily regenerated with a regeneration efficiency of 94.63% after six cycles. The PEI microsphere appears to be a promising candidate material for CO₂ capture from flue gas.

Supported ionic liquids as highly efficient and low-cost material for CO2/CH4 separation process

Physical immobilization of ionic liquids (ILs) in solid materials appears as an interesting strategy for the development of new sorbents for CO₂ separation from natural gas. In this work the effect of physical immobilization of two ionic liquids with different anions (bmim[Cl] and bmim[OAc]) on two mesoporous supports (commercial silica SBA-15 and silica extracted from rice husk) was evaluated for CO₂ separation from natural gas by experimental determination of CO₂ sorption, CO₂/CH₄ selectivity and sorption kinetics. Results showed that the pure supports present the greatest CO₂ sorption capacity when compared to immobilized ILs. However, CO₂ removal efficiency improves considerably in the CO₂/CH₄ mixture when ILs are immobilized in these supports. The best selectivity results were obtained for supports immobilized with the IL bmim[Cl] and values increased for SIL-Cl by 37% and SBA-Cl 51% when compared with their respective supports. The contribution of SIL-Cl (3.03 ± 0.12) to separation performance (CO₂/CH₄) is similar to SBA-Cl (3.29 ± 0.39). ILs supported also presented fast sorption kinetics when compared to pure ILs thus being an interesting alternative in the search for highly efficient and low-cost separation processes.

Nitrogen-decorated, porous carbons derived from waste cow manure as efficient catalysts for the selective capture and conversion of CO2

The catalytic conversion of CO2 is a promising solution to the greenhouse effect and simultaneously recycles the carbon sources to produce high value-added chemicals. Herein, we demonstrated a class of nanoporous carbons, which were synthesized by the direct carbonization of bio-waste cow manure, followed by activation with KOH and NaNH2. Various characterizations indicate that the resultant nanoporous carbons have abundant nanopores and nitrogen sites. As a result, their performances for the capture and catalytic conversion of CO2 were investigated. The synthesized nanoporous carbons exhibited superior properties for the selective capture and catalytic cycloaddition of CO2 to propylene oxide as compared to various solid materials.

Ordered mesoporous carbon with enhanced porosity to support organic amines: efficient nanocomposites for the selective capture of CO2

Highly ordered mesoporous carbon with a much expanded porosity was impregnated with PEI to act as an efficient composite material for the highly selective capture of CO₂ from flue gas.